Flood inundation modeling using MIKE FLOOD and remote sensing data

A coupled 1D-2D hydrodynamic model, MIKE FLOOD was used to simulate the flood inundation extent and flooding depth in the delta region of Mahanadi River basin in India. Initially, the 1D model MIKE 11 was calibrated using river water level and discharge data of various gauging sites for the monsoon period (June to October) of the year 2002. Subsequently, the calibrated set up was validated using both discharge and water level data for the same period of the year 2001. The performance of calibration and validation results of MIKE 11 were evaluated using different performance indices. A bathymetry of the study area with a spatial resolution of 90m was prepared from SRTM DEM and provided as an input to the 2D model, MIKE 21. MIKE 11 and MIKE 21 models were then coupled using lateral links to form the MIKE FLOOD model set up for simulating the two dimensional flood inundations in the study area. Flood inundation is simulated for the year 2001 and the maximum flood inundation extent simulated by the model was compared with the corresponding actual inundated area obtained from IRS-1D WiFS image.     

The IGS VTEC maps: a reliable source of ionospheric information since 1998

The International GNSS Service (IGS) Working Group on Ionosphere was created in 1998. Since then, the Scientific community behind IGS, in particular CODE, ESA, JPL and UPC, have been continuosly contributing to reliable IGS combined vertical total electron content (VTEC) maps in both rapid and final schedules. The details on how these products are being generated, performance numbers, proposed improvement as far as VTEC evolution trends during near one Solar Cycle, are summarized in this paper. The confirmation of (1) the good performance of the IGS combined VTEC maps, and (2) the characteristic VTEC variability periods, are two main results of this work.     

Generation and validation of DEM using SAR interferometry and differential GPS supported by multispectral optical data

Digital elevation model (DEM) and the derived terrain parameters e.g. contour, slope, aspect, drainage pattern, etc are required for natural resources management, infrastructure planning and disaster management. The present paper aims at generating DEM from ERS tandem pair using interferometric technique supported by differential GPS measurements (DGPS) and multispectral optical data. Validation of DEM has been carried out by DGPS measurements. Ground Control Points (GCP) established by DGPS measurements have been used to georeference the IRS-1D optical data that has finally been co-registered with SAR amplitude image. Optical data, co-registered with ERS - I SAR data has helped in locating the GCP’s and check points, precisely, for refinement of DEM and its validation.     

Use of laser range and height texture cues for building identification

Airborne LiDAR has found application in an increasing number of mapping and Geo-data acquisition tasks. Apart from terrain information generation, applications such as automatic detection and modeling of objects like buildings or vegetation for the generation of 3-D city models have been explored. Besides the height itself, height texture defined by local variations of the height is a significant parameter for object recognition. The paper explores the potential of the analysis of height texture as a cue for the automatic detection of objects in LiDAR datasets. A number of texture measures were computed. Based on their definition and computation these measures were used as bands in a classification algorithm, and objects like buildings, single trees, and roads could be recognized.     

Distribution analysis of salt affected soils under canal and non-canal command area in a part of Etah district,U. P., using remote sensing technique

A World Bank-aided project on sodic land reclamation in Uttar Pradesh is being executed by U.P. Bhumi Sudhar Nigam, Lucknow, and Remote Sensing Applications Centre, U.P., Lucknow has the responsibility of sodic land mapping for the execution of land reclamation programme at the cadastral level. Sodic lands are mainly concentrated in the Gangetic alluvial plains but the problem of sodicity is particularly acute in the canal-irrigated areas. A study of the distribution pattern of sodic lands in canal and noncanal command areas in a reclamation site (covering 60 villages out of which sodic lands were mapped in 51 villages) of Etah district in Uttar Pradesh, indicates that 18.39 per cent area of the canal command villages was barren sodic which was 13.41 per cent of the total geographical area of the site (15417 ha), however, 11.69 per cent area was recorded to be barren sodic in the non-canal command villages which was only 3.16 per cent of the geographical area of the site. The results of soil chemical analysis indicate that barren sodic lands of canal command area are saline-sodic with higher concentration of soluble salts (pH₂ >8.5, EC₂ >4 dSm⁻¹), however, those of non-canal command area are sodic (pH₂ >8.5, EC₂ <4 dSm⁻¹). The post-monsoon ground level in the canal-irrigated areas was in the critical and semicritical zone (< 3.0 mbgl) whereas it was well below the semi-critical zone in the non-canal command area, which indicates that the high ground water level is a major factor to higher the area under sodicity.     

Mapping of suspended sediments using site specific seasonal algorithms

This article reports a preliminary work in which two site specific seasonal algorithms have been proposed for estimating the suspended sediments concentration (SSC) from the digital numbers recorded on Indian Remote sensing Satellite, IRS-P4 Ocean Colour Monitor (OCM) sensor. For estimation of SSC, the proposed algorithms utilize dark pixel deduction atmospheric correction technique. The computations are performed with respect to north east monsoon phase situations of Palk Strait coastal stretch. The algorithms performance was satisfactory during the north east monsoon period. Although the results obtained cannot be generalized, we suggest that the authority of proposed algorithms can be extended to other seasons with the addition of more temporal experimental validation data sets and with numeric constants adjusted to present existing conditions. (As this area was severely affected by Tsunami, it may have dissimilar conditions at present).     

Applications of AnnAGNPS model for soil loss estimation and nutrient loading for Malaysian conditions

The study evaluated the performance and suitability of AnnAGNPS model in assessing runoff, sediment loading and nutrient loading under Malaysian conditions. The watershed of River Kuala Tasik in Malaysia, a combination of two sub-watersheds, was selected as the area of study. The data for the year 2004 was used to calibrate the model and the data for the year 2005 was used for validation purposes. Several input parameters were computed using methods suggested by other researchers and studies carried out in Malaysia. The study shows that runoff was predicted well with an overall R² value of 0.90 and E value of 0.70. Sediment loading was able to produce a moderate result of R² = 0.66 and E = 0.49, nitrogen loading predictions were slightly better with R² = 0.68 and E = 0.53, and phosphorus loading performance was slightly poor with an R² = 0.63 and E = 0.33. The erosion map developed was in agreement with the erosion risk map produced by the Department of Agriculture, Malaysia. Rubber estates and urban areas were found to be the main contributors to soil erosion. The simulation results showed that AnnAGNPS has the potential to be used as a valuable tool for planning and management of watersheds under Malaysian conditions.     

Approaches for comparative evaluation of raster GIS-based landslide susceptibility zonation maps

Evaluation of maps generated from different conceptual models or data processing approaches at spatial level has importance in many geoenvironmental applications. This paper addresses the spatial comparison of different landslide susceptibility zonation (LSZ) raster maps of the same area derived from various procedures.     

An image engineering system for the inspection of transparent construction materials

This article presents a modular photogrammetric recording and image analysis system for inspecting the material characteristics of transparent foils, in particular Ethylen–TetraFluorEthylen-Copolymer (ETFE) foils. The foils are put under increasing air pressure and are observed by a stereo camera system. Determining the time-variable 3D shape of transparent material imposes a number of challenges: especially the automatic point transfer between stereo images and, in temporal domain, from one image pair to the next. We developed an automatic approach that accommodates for these particular circumstances and allows reconstruction of the 3D shape for each epoch as well as determining 3D translation vectors between epochs by feature tracking. Examples including numerical results and accuracy measures prove the applicability of the system.