Geochemical transport modelling of drainage from experimental mine tailings cells covered by capillary barriers

The use of covers with capillary barrier effects (CCBEs) for reducing acid mine drainage (AMD) from sulphidic mine tailings is simulated using the MIN3P finite volume model for coupled groundwater flow, O₂ diffusion and multi-component reactive transport. The model is applied to simulate five pilot-scale in situ test cells containing reactive tailings from the Manitou mine site, Val d’Or, Que., Canada. Four of the cells were constructed with CCBEs over the tailings, while the fifth tailings cell was left uncovered. Observed and simulated discharge from the base of each cell showed that the capillary barrier covers significantly reduced sulphide oxidation and AMD. Compared to acidic discharge from the uncovered cell, discharge from the four CCBE-covered cells had neutral pH levels and 1–7 orders of magnitude lower concentrations of SO₄, Fe, Zn, Cu and Al. The simulations showed that the moisture retaining layer of the CCBEs reduced AMD by inhibiting O₂ diffusion into the underlying reactive wastes. Provided the moisture-retention layer of the CCBE remains close to saturation, its thickness had a relatively minor effect. Under such near-saturated conditions, O₂ availability is limited by its diffusion rate through the bulk porous medium and not by the diffusion rate through the oxidized grain shells. The model is providing important new insights for comparing design alternatives for reducing or controlling AMD.     

Element discharge from pyritic mine tailings at limited oxygen availability in column experiments

Sulfide mineral oxidation in mine tailings deposits poses a long term threat to surrounding ground water and surface waters. Soil or water cover remediation aims at reducing the rate of sulfide mineral oxidation by decreasing the O₂ ingress rate. In this study, the authors addressed the rate of sulfide oxidation and pH buffering in ∼33 months long, well-controlled laboratory studies of water saturated columns of sulfidic mine tailings from the Kristineberg site in Sweden at reduced O₂ availability. The element discharge rates slowly declined towards a quasi-steady state over hundreds of days. Non-reactive tracer tests showed an anomalously large dispersion, indicating strong flow heterogeneity, possibly including preferential flow and/or stagnant water zones. Congruent dissolution of pyrite and sphalerite by injected oxidants (dissolved O₂ and Fe(III)) adequately explained the discharge rate of Fe, S and Zn at quasi-steady state. Arsenic, Pb and Cu were partly retained in the tailings. Base cation discharge rates, and thus pH buffering, were apparently controlled by the rate of acidity production, with actual pH levels, available mineral surface area, and water residence times being of less importance.     

Immobilization of toxic elements in mine residues derived from mining activities in the Iberian Pyrite Belt (SW Spain): Laboratory experiments

In the mining environments of the Iberian Pyrite Belt (IPB), the oxidation of sulphide wastes generates acid drainage with high concentrations of SO₄, metals and metalloids (Acid Mine Drainage, AMD). These acid and extremely contaminated discharges are drained by the fluvial courses of the Huelva province (SW Spain) which deliver high concentrations of potentially toxic elements into the Gulf of Cádiz. In this work, the oxidation process of mine tailings in the IPB, the generation of AMD and the potential use of coal combustion fly ash as a possible alkaline treatment for neutralization of and metal removal from AMD, was studied in non-saturated column experiments. The laboratory column tests were conducted on a mine residue (71.6 wt% pyrite) with artificial rainfall or irrigation. A non-saturated column filled solely with the pyrite residue leached solutions with an acid pH (approx. 2) and high concentrations of SO₄ and metals. These leachates have the same composition as typical AMD, and the oxidation process can be compared with the natural oxidation of mine tailings in the IPB. However, the application of fly ash to the same amount of mine residue in another two non-saturated columns significantly increased the pH and decreased the SO₄ and metal concentrations in the leaching solutions. The improvement in the quality of leachates by fly ash addition in the laboratory was so effective that the leachate reached the pre-potability requirements of water for human consumption under EU regulations. The extrapolation of these experiments to the field is a promising solution for the decontamination of the fluvial courses of the IPB, and therefore, the decrease of pollutant loads discharging to the Gulf of Cádiz.     

Experimental and numerical evaluation of single-layer covers placed on acid-generating tailings

This study focuses on the reclamation work being performed on two former acid-generating tailings sites, located in Quebec, Canada. At both sites, the tailings were partially oxidized due to extended exposure, and the pore water is acidic. The reclamation solution applied to control acid mine drainage is a monolayer cover, made of non acid-generating tailings in one case and a till in the other. The goal of this project was to assess the response of the tailings-cover systems under various conditions. Tailings samples were collected in situ and characterized in the laboratory. Large column tests were conducted to evaluate the hydrogeological and geochemical behaviour of the covered tailings following wetting and drying cycles. The instrumented columns were designed to reproduce some of the existing site conditions and provide representative results for longer term analyses. Volumetric water content, suction, and oxygen concentrations were also monitored over time. The experimental data were used to validate different numerical models including those constructed with Vadose/W (GeoSlope Int.). Additional simulations were conducted under field conditions to evaluate the effect of various influence factors such as the depth of the water table, climatic conditions and the thickness of the cover. The combination of experimental and numerical results show how the behaviour and efficiency of a monolayer cover placed over reactive tailings depend on these factors, highlighting the importance of hydrogeological properties and water table depth. In many instances, the cover materials were prone to desaturation, especially when the water table was deeper than about 2 m below the tailings-cover interface. These results tend to indicate that relatively thin monolayer covers would not be able to prevent oxygen ingress under some of the conditions observed in the field. Desaturation of the cover and/or reactive tailings is due to a combination of drainage and evaporation. In such cases, increasing the thickness of the monolayer cover only has a limited effect. A discussion follows on the practical implications of these laboratory experiments and the numerical simulations for field design of reclamation measures at these two tailings impoundments.     

Geochemical and mineralogical aspects of sulfide mine tailings

Tailings generated during processing of sulfide ores represent a substantial risk to water resources. The oxidation of sulfide minerals within tailings deposits can generate low-quality water containing elevated concentrations of SO₄, Fe, and associated metal(loid)s. Acid generated during the oxidation of pyrite [FeS₂], pyrrhotite [Fe_(1−x)S] and other sulfide minerals is neutralized to varying degrees by the dissolution of carbonate, (oxy)hydroxide, and silicate minerals. The extent of acid neutralization and, therefore, pore-water pH is a principal control on the mobility of sulfide-oxidation products within tailings deposits. Metals including Fe(III), Cu, Zn, and Ni often occur at high concentrations and exhibit greater mobility at low pH characteristic of acid mine drainage (AMD). In contrast, (hydr)oxyanion-forming elements including As, Sb, Se, and Mo commonly exhibit greater mobility at circumneutral pH associated with neutral mine drainage (NMD). These differences in mobility largely result from the pH-dependence of mineral precipitation–dissolution and sorption–desorption reactions. Cemented layers of secondary (oxy)hydroxide and (hydroxy)sulfate minerals, referred to as hardpans, may promote attenuation of sulfide-mineral oxidation products within and below the oxidation zone. Hardpans may also limit oxygen ingress and pore-water migration within sulfide tailings deposits. Reduction–oxidation (redox) processes are another important control on metal(loid) mobility within sulfide tailings deposits. Reductive dissolution or transformation of secondary (oxy)hydroxide phases can enhance Fe, Mn, and As mobility within sulfide tailings. Production of H₂S via microbial sulfate reduction may promote attenuation of sulfide-oxidation products, including Fe, Zn, Ni, and Tl, via metal-sulfide precipitation. Understanding the dynamics of these interrelated geochemical and mineralogical processes is critical for anticipating and managing water quality associated with sulfide mine tailings.     

A laboratory study of covers made of low-sulphide tailings to prevent acid mine drainage

Covers with capillary barrier effects (CCBE) are considered to be one of the most effective ways to control acid mine drainage (AMD) production from mine wastes. The use of low-sulphide tailings in CCBE has been proposed recently for cases where other types of material may be unavailable near the mining site. This paper presents leaching column test results showing that CCBEs with a moisture-retaining layer made of slightly reactive tailings, with three different sulphide contents, can effectively limit the production of AMD from the acid-generating tailings placed underneath. With these layered covers, the leachate pH was maintained near neutrality throughout the testing period. When compared to uncovered tailings, the efficiency of the cover systems for reducing the amount of contaminants in the percolated water was determined to be greater than 99% for zinc, copper and iron. This study shows that the use of low-sulphide tailings can improve the ability of a CCBE to limit gas diffusion by consuming a fraction of the migrating oxygen.     

Geochemical behavior and speciation modeling of rare earth elements in acid drainages at Sarcheshmeh porphyry copper deposit,Kerman Province,Iran

Acid mine drainage is a major source of water pollution in the Sarcheshmeh porphyry copper mine area. The concentrations of heavy metals and rare earth elements (REEs) in the host rocks, natural waters and acid mine drainage (AMD) associated with mining and tailing impoundments are determined. Contrary to the solid samples, AMDs and impacted stream waters are enriched in middle rare earth elements (MREEs) and heavy rare earth elements (HREEs) relative to light rare earth elements (LREEs). This behavior suggests that REE probably fractionate during sulfide oxidation and acid generation and subsequent transport, so that MREE and HREE are preferentially enriched. Speciation modeling predict that the dominant dissolved REE inorganic species are Ln³⁺, Ln(SO₄)₂⁻, LnSO₄⁺, LnHCO₃²⁺, Ln(CO₃)₂⁻ and LnCO₃⁺. Compared to natural waters, Sarcheshmeh AMD is enriched in REEs and SO₄²⁻. High concentrations of SO₄²⁻ lead to the formation of stable LnSO₄⁺, thereby resulting in higher concentrations of REEs in AMD samples. The model indicates that LnSO₄⁺ is the dissolved form of REE in acid waters, while carbonate and dicarbonate complexes are the most abundant dissolved REE species in alkaline waters. The speciation calculations indicate that other factors besides complexation of the REE's, such as release of MREE from dissolution and/or desorption processes in soluble salts and poorly crystalline iron oxyhydroxy sulfates as well as dissolution of host rock MREE-bearing minerals control the dissolved REE concentrations and, hence, the MREE-enriched patterns of acid mine waters.     

Mineralogical and geochemical characterization of the Old Tailings Dam,Australia: Evaluating the effectiveness of a water cover for long-term AMD control

Establishing a shallow water cover over tailings deposited in a designated storage facility is one option to limit oxygen diffusion and retard oxidation of sulfides which have the potential to form acid mine drainage (AMD). The Old Tailings Dam (OTD) located at the Savage River mine, western Tasmania contains 38 million tonnes of pyritic tailings deposited from 1967 to 1982, and is actively generating AMD. The OTD was constructed on a natural gradient, resulting in sub-aerial exposure of the southern area, with the northern area under a natural water cover. This physical contrast allowed for the examination of tailings mineralogy and geochemistry as a function of water cover depth across the OTD. Tailings samples (n = 144, depth: ≤ 1.5 m) were collected and subjected to a range of geochemical and mineralogical evaluations. Tailings from the southern and northern extents of the OTD showed similar AMD potential based on geochemical (NAG pH range: 2.1 to 4.2) and bulk mineralogical parameters, particularly at depth. However, sulfide alteration index (SAI) assessments highlighted the microscale contrast in oxidation. In the sub-aerial zone pyrite grains are moderately oxidized to a depth of 0.3 m (maximum SAI of 6/10), under both gravel fill and oxidized covers, with secondary minerals (e.g., ferrihydrite and goethite) developed along rims and fractures. Beneath this, mildly oxidized pyrite is seen in fresh tailings (SAI = 2.9/10 to 5.8/10). In the sub-aqueous zone, the degree of pyrite oxidation demonstrates a direct relationship with cover depth, with unoxidized, potentially reactive tailings identified from 2.5 m, directly beneath an organic-rich sediment layer (SAI = 0 to 1/10). These findings are broadly similar to other tailings storage facilities e.g., Fox Lake, Sherritt-Gordon ZnCu mine, Canada and Stekenjokk mine, Sweden where water covers up to 2 m have successfully reduced AMD. Whilst geotechnical properties of the OTD restrict the extension of the water cover, pyrite is enriched in cobalt (up to 2.6 wt%) indicating reprocessing of tailings as an alternative management option. Through adoption of an integrated mineralogical and geochemical characterization approach for tailings assessment robust management strategies after mine closure can be developed.     

Release,transport and attenuation of metals from an old tailings impoundment

The oxidation of sulfide minerals from mine wastes results in the release of oxidation products to groundwater and surface water. The abandoned high-sulfide Camp tailings impoundment at Sherridon, Manitoba, wherein the tailings have undergone oxidation for more than 70 a, was investigated by hydrogeological, geochemical, and mineralogical techniques. Mineralogical analysis indicates that the unoxidized tailings contain nearly equal proportions of pyrite and pyrrhotite, which make up to 60 wt% of the total tailings, and which are accompanied by minor amounts of chalcopyrite and sphalerite, and minute amounts of galena and arsenopyrite. Extensive oxidation in the upper 50 cm of the tailings has resulted in extremely high concentrations of dissolved SO₄ and metals and As in the tailings pore water (pH < 1, 129,000 mg L⁻¹ Fe, 280,000 mg L⁻¹ SO₄, 55,000 mg L⁻¹ Zn, 7200 mg L⁻¹ Al, 1600 mg L⁻¹ Cu, 260 mg L⁻¹ Mn, 110 mg L⁻¹ Co, 97 mg L⁻¹ Cd, 40 mg L⁻¹ As, 15 mg L⁻¹ Ni, 8 mg L⁻¹ Pb, and 3 mg L⁻¹ Cr). The acid released from sulfide oxidation has been extensive enough to deplete carbonate minerals to 6 m depth and to partly deplete Al-silicate minerals to a 1 m depth. Below 1 m, sulfide oxidation has resulted in the formation of a continuous hardpan layer that is >1 m thick. Geochemical modeling and mineralogical analysis indicate that the hardpan layer consists of secondary melanterite, rozenite, gypsum, jarosite, and goethite. The minerals indicated mainly control the dissolved concentrations of SO₄, Fe, Ca and K. The highest concentrations of dissolved metals are observed directly above and within the massive hardpan layer. Near the water table at a depth of 4 m, most metals and SO₄ sharply decline in concentration. Although dissolved concentrations of metals and SO₄ decrease below the water table, these concentrations remain elevated throughout the tailings, with up to 60,600 mg L⁻¹ Fe and 91,600 mg L⁻¹ SO₄ observed in the deeper groundwater. During precipitation events, surface seeps develop along the flanks of the impoundment and discharge pore water with a geochemical composition that is similar to the composition of water directly above the hardpan. These results suggest that shallow lateral flow of water from a transient perched water table is resulting in higher contaminant loadings than would be predicted if it were assumed that discharge is derived solely from the deeper primary water table. The abundance of residual sulfide minerals, the depletion of aluminosilicate minerals in the upper meter of the tailings and the presence of a significant mass of residual sulfide minerals in this zone after 70 a of oxidation suggest that sulfide oxidation will continue to release acid, metals, and SO₄ to the environment for decades to centuries.     

The mobility of radium-226 and trace metals in pre-oxidized subaqueous uranium mill tailings

The exchange of ²²⁶Ra and trace metals across the tailings-water interface and the mechanisms governing their mobility were assessed via sub-centimetre resolution profiling of dissolved constituents across the tailings–water interface in Cell 14 of the Quirke Waste Management Area at Rio Algom's Quirke Mine, near Elliot Lake, Ontario, Canada. Shallow zones (<1.5 m water depth) are characterized by sparse filamentous vegetation, well-mixed water columns and fully oxygenated bottom waters. Profiles of dissolved O₂, Fe and Mn indicate that the tailings deposits in these areas are sub-oxic below tailings depths of ∼3 cm. These zones exhibit minor remobilization of Ra in the upper 5 cm of the tailings deposit; ²²⁶Ra fluxes at these sites are relatively small, and contribute negligibly to the water column activity of ²²⁶Ra. The shallow areas also exhibit minor remobilization of Ni, As, Mo and U. The release of these elements to the water cover is, however, limited by scavenging mechanisms in the interfacial oxic horizons. The presence of thick vegetation (Chara sp.) in the deeper areas (>2 m water depth) fosters stagnant bottom waters and permits the development of anoxia above the benthic boundary. These anoxic tailings are characterized by substantial remobilization of ²²⁶Ra, resulting in a relatively large flux of ²²⁶Ra from the tailings to the water column. The strong correlation between the porewater profiles of ²²⁶Ra and Ba (r²=0.99), as well as solubility calculations, indicate that the mobility of Ra is controlled by saturation with respect to a poorly ordered and/or impure barite phase [(Ra,Ba)SO₄]. In the anoxic zones, severe undersaturation with respect to barite is sustained by microbial SO₄ reduction. Flux calculations suggest that the increase in ²²⁶Ra activity in the water cover since 1995 (from <0.5 to 2.5 Bq l⁻¹) can be attributed to an increase in the spatial distribution of anoxic bottom waters caused by increased density of benthic flora. The anoxic, vegetated areas also exhibit minor remobilization with respect to dissolved As, Ni and Zn. The removal of trace metals in the anoxic bottom waters appears to be limited by the availability of free sulphide. Collectively, the data demonstrate that while the water cover over the U mill tailings minimizes sulphide oxidation and metal mobility, anoxic conditions which have developed in deeper areas have led to increased mobility of ²²⁶Ra.     

Effect of acid mine drainage on a karst basin: a case study on the high-As coal mining area in Guizhou province,China

Acid mine drainage (AMD) is a common pollution in mining areas due to the oxidation of pyrite and associated sulfide minerals at mines, tailings and mine dumps. Elevated metals (Fe, Mn, Al) and metalloids (As, Hg) in AMD would deteriorate the local aquatic environment and influence the water supply. A carbonate basin with deposits of high-arsenic coal in Xingren County, southwestern China, was chosen to study the behavior of As and other chemical constituents along a river receiving AMD. Heavy metals (Fe, Mn) and major ions such as (Ca²⁺, Mg²⁺, Cl⁻, SO₄ ²⁻) in surface water, and As in sediment and surface water were analyzed. It was found that high concentrations of SO₄ ²⁻ (1,324–7,560 mg/L) and Fe (369–1,472 mg/L) in surface water were mainly controlled by the interactions between water and rocks such as the oxidation of pyrite in the local coal seams, precipitation and adsorption of iron minerals. Although ubiquitous carbonate minerals in the bedrock and the riverbeds, low pH (<3) water was maintained until 2 km downstream from the AMD source due to the Fe(hydro)oxide minerals coating on the surface of carbonate minerals to restrain the neutralization of acidic water. Moreover, the formation of Fe(hydro)oxide precipitations absorbed As was dominated the attenuation of As from water to sediment. Whereas, the dilution also played an important role in decrease of As in river water.     

The effects of hardpan layers on the water chemistry from the leaching of pyrrhotite-rich tailings material

Column leaching experiments were used to determine the effects of an iron-rich hardpan layer, on the rate of tailings oxidation and the composition of leachate waters, from the Renison Bell tailings dams in western Tasmania, Australia. One-meter-long PVC columns, filled with tailings, cover material (Cassiterite Flotation Tailings) and hardpan samples from the tailings dams, were leached over a period of 14 weeks. Under dry cover conditions, when hardpan was present, the solute loads peaked at 21–49 days (Fe at 2,294 ppm and SO ₄ ^2- at 4,700 ppm), and stabilised at much lower concentrations after 9 weeks. In contrast, the solute loads steadily increased over time in the column where hardpan was absent (SO ₄ ^2- from 1,800 to 3,100 ppm, and Fe from 407 to 1,692 ppm). Under saturated cover conditions, the solute concentrations in the leachate also increased with time (SO ₄ ^2-from 1,900 to 17,000 ppm, and Fe from 480 to 8,500 ppm). The presence of a hardpan layer between the reactive tailings and cover material has been found to improve leachate water chemistry and lessen the rate of sulphide oxidation.     

Hydrochemistry of superficial waters in the Adoria mine area (Northern Portugal): environmental implications

The purpose of this work is to characterize the hydrochemical behavior of acid mine drainages (AMD) and superficial waters from the Adoria mine area (Northern Portugal). Samples of superficial and mine drainage water were collected for one year, bi-monthly, with pH, temperature, Eh, conductivity and HCO₃ determined in situ with chemical analyses of SO₄, Ca, K, Mg, Na, Cl, Ag, As, Bi, Co, Cu, Fe, Mn, Ni, Pb, Zn and Cd. In the mine, there are acidic waters, with low pH and significant concentrations of SO₄, and metals (Fe, Mn, Zn, Cu, Pb, Cd and Ni), while in the superficial natural stream waters outside the mine, the pH is close to neutral, with low conductivity and lower metal concentrations. The stream waters inside the mine influence are intermediate in composition between AMD and natural stream waters outside the mine influence. Principal Component Analysis (PCA) shows a clear separation between AMD galleries and AMD tailings, with tailings having a greater level of contamination.     

Geochemical distribution and removal of As,Fe, Mn and Al in a surface water system affected by acid mine drainage at a coalfield in Southwestern China

The chemical characteristics, formation and natural attenuation of pollutants in the coal acid mine drainage (AMD) at Xingren coalfield, Southwest China, are discussed in this paper based on the results of a geochemical investigation as well as geological and hydrogeological background information. The chemical composition of the AMD is controlled by the dissolution of sulfide minerals in the coal seam, the initial composition of the groundwater and the water–rock interaction. The AMD is characterized by high sulfate concentrations, high levels of dissolved metals (Fe, Al, Mn, etc.) and low pH values. Ca²⁺ and SO₄ ²⁻ are the dominant cation and anion in the AMD, respectively, while Ca²⁺ and HCO₃ ⁻ are present at significant levels in background water and surface water after the drainage leaves the mine site. The pH and alkalinity increase asymptotically with the distance along the flow path, while concentrations of sulfate, ferrous iron, aluminum and manganese are typically controlled by the deposition of secondary minerals. Low concentrations of As and other pollutants in the surface waters of the Xingren coalfield could be due to relatively low quantities being released from coal seams, to adsorption and coprecipitation on secondary minerals in stream sediments, and to dilution by unpolluted surface recharge. Although As is not the most serious water quality problem in the Xingren region at present, it is still a potential environmental problem. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Mineralogical,geochemical, and microbial investigation of a sulfide-rich tailings deposit characterized by neutral drainage

Mineralogical, geochemical and microbial characterization of tailings solids from the Greens Creek Mine, Juneau, Alaska, was performed to evaluate mechanisms controlling aqueous geochemistry of near-neutral pH pore water and drainage. Core samples of the tailings were collected from five boreholes ranging from 7 to 26 m in depth. The majority of the 51 samples (77%) were collected from the vadose zone, which can extend >18 m below the tailings surface. Mineralogical investigation indicates that the occurrence of sulfide minerals follows the general order: pyrite [FeS₂] >> sphalerite [(Zn,Fe)S] > galena [PbS], tetrahedrite [(Fe,Zn,Cu,Ag)₁₂Sb₄S₁₃] > arsenopyrite [FeAsS] and chalcopyrite [CuFeS₂]. Pyrite constitutes <20 to >35 wt.% of the tailings mineral assemblage, whereas dolomite [CaMg(CO₃)₂] and calcite [CaCO₃] are present at ?30 and 3 wt.%, respectively. The solid-phase geochemistry generally reflects the mineral assemblage. The presence of additional trace elements, including Cd, Cr, Co, Mo, Ni, Se and Tl, is attributed to substitution into sulfide phases. Results of acid–base accounting (ABA) underestimated both acid-generating potential (AP) and neutralization potential (NP). Recalculation of AP and NP based on solid-phase geochemistry and quantitative mineralogy yielded more representative results. Neutrophilic S-oxidizing bacteria (nSOB) and SO₄-reducing bacteria (SRB) are present with populations up to 10⁷ and 10⁵ cells g⁻¹, respectively. Acidophilic S-oxidizing bacteria (aSOB) and iron-reducing bacteria (IRB) were generally less abundant. Primary influences on aqueous geochemistry are sulfide oxidation and carbonate dissolution at the tailings surface, gypsum precipitation–dissolution reactions, as well as Fe reduction below the zone of sulfide oxidation. Pore-water pH values generally ranged from 6.5 to 7.5 near the tailings surface, and from approximately 7–8 below the oxidation zone. Elevated concentrations of dissolved SO₄, S₂O₃, Fe, Zn, As, Sb and Tl persisted under these conditions.     

Multiphase flow and reactive transport model in vadose tailings

Weathering processes affecting pyritic wastes may generate huge amounts of acid waters with high concentrations of potentially toxic contaminants (acid mine drainage). Acid mine drainage is mainly produced in the vadose zone. In the present study, a coupled non-isothermal multiphase flow and reactive transport model of the vadose zone of sulfide mine tailings was developed. The geochemical model included kinetically controlled reactions for Fe(II)-oxidation and for the dissolution of sulfide and aluminosilicate phases and the Pitzer ion-interaction model to describe the behavior of the pore-water solutions. Model results were compared with experimental observations in unsaturated column experiments under strongly evaporative conditions similar to arid or semiarid climates. Evolution trends for temperature, water saturation, evaporation rates, pore-water hydrochemistry and mineral phases observed during the drying experiment were adequately reproduced. The coupled model reproduced the increase of solute concentrations in the column top and the precipitation of a crust of secondary mineral phases. This crust became a barrier for water vapour diffusion to the atmosphere and modified the thermohydraulic behavior of the tailings. Enhanced downward migration of water vapour and its condensation in this colder end of the column were correctly taken into account by the model, which reproduced the dilution observed in the lower part of the column during the experiments.     

Spatial variations in water composition at a northern Canadian lake impacted by mine drainage

Release of acid drainage from mine-waste disposal areas is a problem of international scale. Contaminated surface water, derived from mine wastes, orginates both as direct surface runoff and, indirectly, as subsurface groundwater flow. At Camp Lake, a small Canadian Shield lake that is in northern Manitoba and is ice-covered 6 months of the year, direct and indirect release of drainage from an adjacent sulfide-rich tailings impoundment has severely affected the quality of the lake water. Concentrations of the products from sulfide oxidation are extremely high in the pore waters of the tailings impoundment. Groundwater and surface water derived from the impoundment discharge into a semi-isolated shallow bay in Camp Lake. The incorporation of this aqueous effluent has altered the composition of the lake water, which in turn has modified the physical limnology of the lake. Geochemical profiles of the water column indicate that, despite its shallow depth (6 m), the bay is stratified throughout the year. The greatest accumulation of dissolved metals and SO₄ is in the lower portion of the water column, with concentrations up to 8500 mg L⁻¹ Fe, 20,000 mg L⁻¹ SO₄, 30 mg L⁻¹ Zn, 100 mg L⁻¹ Al, and elevated concentrations of Cu, Cd, Pb and Ni. Meromictic conditions and very high solute concentrations are limited to the bay. Outside the bay, solute concentrations are lower and some stratification of the water column exists. Identification of locations and composition of groundwater discharge relative to lake bathymetry is a fundamental aspect of understanding chemical evolution and physical stability of mine-impacted lakes.