RQD应用与研究的回顾与展望

RQD是评价裂隙岩体质量的重要参数,它在岩体工程中被广泛采用,但经过长期的理论和实践工程师们认识到了RQD自身所存在的缺点和不足,并将RQD的缺点和不足总结为5点。但RQD仍然具有很强的生命力,从5个方面总结了近半个世纪以来人们对RQD的不断探索和研究的进程,并进一步指出了对RQD的拓宽和改进的主要研究方法和发展方向。     

Stereotomography

The following paper presents a new exploration technique called stereotomography. Such a technique appropriately combines stereograms with data from borecores or from drillhole logs. Its purpose will be to show graphically the general trends of data for structural domains, for sectors, or for a whole mine. This method has been originally designed for discrete RQD measurements between boreholes, but it also has many other uses when RQD is substituted by any other physical or geophysical parameter related to the rock mass. In their example case, the authors found that such a so-called stereotomographic technique, supported by a complete structural geology study, will be decisive in the choice of potential mining sites, since it can delimit the discontinuity attitudes present inside the rock mass.     

基于空间插值的工程岩体RQD预测方法

作为工程实际中评价岩体性质的重要指标,RQD的应用已相当广泛。但工程岩体中RQD值的分布存在一定的结构性和随机性,因此,通过对特定位置钻探获取的RQD值无法很到位地表达整个空间区域的实际岩石质量。为了弥补这方面的不足,统计学中的空间插值法为此提供了有力的手段。考虑到空间RQD分布存在各向异性,以及在工程坐标系中很难描述RQD分布的结构性,首先计算工程坐标系下已获取RQD值的主要黑塞方向（pHd）;然后构建空间旋转与比例缩放矩阵对其进行坐标标准化处理。在标准化的空间中,引入Kriging插值法,采用变异函数描述RQD在标准空间结构上的变化,建立其空间变异规律的数学模型,并对其进行插值计算;最后将标准空间进行坐标逆变换,实现了对工程坐标系下RQD分布的预测。利用R语言编程将该方法应用于工程实例,结果表明,这种空间插值法能够有效地预测工程岩体中RQD值的分布规律,弥补了局部钻探的局限性。     

补充RQD值的几类岩体质量评价图

针对ＲＱＤ值不能全面反映裂隙间跑、块体大小以及随机表象的多重尺度等问题,介绍了三种岩体质量评价图,即基于裂隙岩体分数维结构之上的分维岩体质量图、考虑裂隙长度的累积长度图、建立在不同岩块频度基础上的岩块累积频度图。根据不同图解对岩体质量进行了评价,并对岩体完整性作了划分、三种图解能较全面反映岩体质量的特点,表明它们是ＲＱＤ的有益补充。     

岩石质量描述图与岩石质量风险分析探讨

本文针对结构面间距最常见的两种分布形式－－负指数分布和对数正态分布，探讨了岩石质量指标（RQD）的Monte-Carlo模拟方法，首和无根据结构面间距分布密度函数产和一包含50万个随机结构面并按生成顺序排列的模拟真实岩体的总测线，然后为了和实际 钻探时以2米测线计算RQD相一致，在总测线上按均匀分布形式随机抽取大于等于2米的局部测线共5万个计算RQD单值，并进一步统计得出所有RQD的平均值，RQD累积分布曲及岩石质量描述图，对于自然界大部分岩体，可根据结构面间距统计参数，直接在本文得出的一系列岩石质量图上定出RQD平均值，岩石质量百分比（RQP）及岩石质量风险（RQR）。     

北山花岗岩深部节理间距分布多重分形研究

岩体节理几何特征定量描述是岩体力学性质和渗透性研究的基础,更是核废料处置库场址筛选和评价过程的主要内容。基于甘肃北山高放废物深地质处置库预选区BS17、BS18和BS19钻孔岩芯节理数量修正数据,针对节理间距建立了类负指数分布数学统计模型,进一步应用于RQD体系定量评价深部岩体完整性,通过与RID体系对比验证了概率模型的可靠性。指出节理数量-间距关系具有明显的分段线性特征,分维数随着间距增大而增大。确定了节理间距-数量关系符合尺度律,得出了数量与间距关系的多重分形特征。进一步分析了数量与埋深的多重分形特征,初步实现了岩芯节理的定量描述。验证了多重分形谱可以很好地统计分形维特征,尤其是节理几何形状及分布特征。该研究结果可为实现基于钻孔岩芯节理几何特征数据的深部岩体节理三维网格模拟提供参考。     

基于三维结构面网络模拟的岩体变形模量确定方法

变形模量作为表征岩体变形特征的重要参数,是岩体工程设计的基础力学参数之一。在综合前人研究的基础上提出了基于三维结构面网络模拟确定岩体变形模量的方法,编制了三维结构面网络模拟及计算RQD值的程序。以西南山区某水电站坝址区岩体为实例,在概率统计各组优势结构面几何要素分布形式的基础上,采用Monte Carlo法生成三维结构面网络模型,据此获得岩体三维RQD值,利用RMR法进行质量评价和变形模量的确定,并与钻孔资料统计法和原位试验结果进行对比分析。结果表明：基于钻孔资料统计的估算结果与原位试验相对误差达31.62%,且其估算值偏低;基于三维结构面网络模拟的估算结果与原位试验相对误差仅为2.56%,估算结果精度较高。该方法考虑了岩体质量的空间各向异性,对岩体的质量评价和参数确定更为合理,研究成果为该工程的优化设计提供了合理的计算参数。     

Statistical Analysis of Anisotropic Damage of the Bukit Timah Granite

Summary This paper presents a method to analyze probabilistic anisotropic initial damage of a rock mass. A three-dimensional geometric model of cracks in a rock mass is established in terms of several parameters, such as orientations, spacing and normalized sizes of cracks in the rock mass. The dip, dip direction, spacing, and normalized size of cracks of the Bukit Timah granite in Singapore were obtained from visual inspection of rock cores, color TV imaging, and impression packer tests in the boreholes at a site of geological investigation. Using the measured data, probabilistic distribution laws of geometric parameters of cracks on the surface of the boreholes are derived. Based on these statistical distributions and using Monte-Carlo simulation method, the distribution of anisotropic initial damage of the Bukit Timah granite is derived and found to have a beta distribution. This anisotropic initial damage distribution of a rock mass can be used in probabilistic analysis of rock mass responses to both static and dynamic loads.     

Comparison of geoelectrical imaging and tunnel documentation at the Hallandsås Tunnel, Sweden

For construction in rock a thorough pre-investigation is important in order to avoid unforeseen conditions which may delay the work. It is crucial to remember the results from this investigation in the further work, and use the experience from the construction to update the geological prognosis and reduce the uncertainties. Different geophysical methods have proved valuable tools in such investigations. In this work the electrical imaging is evaluated with regards to the method's applicability. The evaluation is done qualitatively by comparing the electrical imaging with tunnel documentation from a tunnel in Southern Sweden. By evaluating the result continuously when making the tunnel a more detailed geological prognosis can be compiled and used in the continued work with the tunnel. The parameters used for the comparison are lithology, Q, RQD, weathering and water leakage. The result was that virtually every change in electrical resistivity image coincides with a change in rock conditions. The general trend was that high resistivity corresponded with good quality gneiss whereas low resistivity corresponds to poor quality rock e.g., high weathering, low RQD, low Q and/or several lithological contacts. The intermediate resistivity is often amphibolites or rock with water bearing fractures. The results were supported by in-situ resistivity measurements inside the tunnel and resistivity logging in a core drilling. Geoelectrical imaging proved to give valuable information for a detailed geological model, which could be compiled for a section where the tunnel had not yet been drilled as a help for planning of the continued tunnel work. As is the case other geophysical methods it is clear that for the interpretation of data a priori information about the geological setting is necessary.     

勘察阶段洞室围岩质量预测的问题探讨

因围岩质量评价对地下洞室的设计、施工具有重要作用,因此勘察规范对洞室围岩质量评价具有明确的规定。围岩质量评价方法很多,但在勘察阶段,围岩质量的评价结果与实际情况有很多差别。造成这种问题的主要原因是岩体质量评价需要准确而丰富的工程地质数据,而在勘察阶段,洞室围岩的直接数据有限,多为间接数据(物探数据)和推测数据(以地表工程地质测绘数据和钻孔数据为基础进行推测)。根据勘察阶段所获得的工程地质数据,以钻孔中岩心质量与测井数据之间的关系为基础,建立岩体质量与地球物理参数之间的关系,多种地球物理参数对比,可以比较准确地预测目标围岩质量。通过某花岗岩体中钻孔随深度变化的BQ值曲线、RQD曲线、测井曲线和电磁法物探剖面的对比,发现岩体质量与物探数据很难一一对应,但其大致趋势一致。     

基于结构面迹线分形维数的岩体质量评价

针对传统定性或部分定量的岩体质量评价现状,分形理论、神经网络等新方法得到广泛应用。本文基于岩体结构面迹线自相似性的分形特征,应用分形理论对基于数字近景摄影测量技术获取的岩体边坡结构面迹线的分形维数进行研究。以长春市净月采石场一边坡为例,采用方格网覆盖法计算结构面迹线的分形维数,验证了迹线分形特征,并对方格网覆盖法进行改进,采取与研究范围成比例的长方格网覆盖法计算分形维数。分析发现,两种计算方法结果相近,后者在理论上更接近分形原理并且编程更容易实现,迹线数量越多,分形维数越大,岩体越破碎,质量越差。最后,将分形维数与基于摄影测量方法获得的剔除空白区影响的RQD进行对比分析,确定分形维数与RQD的关系式,得到岩体质量定量评价的分形维数指标。研究表明：研究区边坡迹线分形维数为1.22,拟合度为0.98,此边坡岩体质量属于Ⅱ级。改进的长方形格网覆盖法分形维数计算容易实现,计算过程得到简化,结果可靠。得到了以岩体结构面迹线分形维数为指标的岩体质量定量评价方法。     

利用RQD估算岩体不同深度的平均渗透系数和平均变形模量

渗透系数是进行裂隙岩体渗流模拟的必备参数,变形模量是工程岩体数值模拟的必备参数。大量研究中忽视了渗透系数和变形模量随深度变化这一重要规律,从而影响模拟结果的可靠性。为此,探讨了利用极易获取的RQD（岩石质量指标）资料估算不同深度的渗透系数和变形模量的可行性。通过以某花岗岩体为例,研究发现,RQD均值随深度增大,渗透系数均值随深度减小,其相关性很好。因此,利用RQD估算不同深度的平均渗透系数是可行的。根据RQD随深度的变化,利用经验公式估算了不同深度的变形模量均值和变化范围。估算得到的变形模量与实测结果基本一致。     

高放废物地质处置阿拉善预选区巴彦诺日公地段目标深度岩体质量预测

高放废物地质处置阿拉善预选区巴彦诺日公地段位于阿拉善地块东部,主要由二叠纪侵入的花岗岩构成,地壳次稳定。通过踏勘,确定了2个钻孔,布置了若干条物探剖面。以这2个钻孔为中心,在17km×17km范围内进行了工程地质测绘,获得了地表结构面分布特征。地表岩体质量以III级岩体为主,地表以下3m~4m处多为I级和II级岩体。根据钻孔岩芯编录和力学试验数据,对岩芯质量进行评价,岩芯整体质量较好,以Ⅰ级和Ⅱ级岩体为主。对比岩体质量和测井数据,发现岩体质量与岩体的物理参数具有明显的相关性。通过和CSAMT剖面上对应位置的对比,建立了岩体质量与电阻率的关系。结合地表岩体质量、钻孔岩芯质量和物探剖面,对目标深度岩体进行了预测：目标深度（600m深左右）岩体质量以Ⅰ级岩体为主,局部有Ⅱ级岩体和Ⅲ岩体。     

山脊急拐弯处地下局部含泥带揭露及成因解释——以广东CSNS场地为例

在广东南部低山丘陵区剥蚀卸荷作用或许会导致地下一定深度地应力弱化和局部破碎泥化带生成,这一猜想在中国散裂中子源（CSNS）场地工程地质勘察中得到了证实。电法物探剖面显示出地形上山脊由330°急转为220°向急拐弯处地下局部低阻区、4个钻孔中揭露了完整变粒岩中蚀变长英质变质石英砂岩部位30~40 m深度范围出现局部泥化带。后续施工开挖中也揭露出此现象。数值模拟表明,受剥蚀卸荷影响的山脊近直角拐弯处一定深度范围内应力降低,靠近岩脉与变粒岩接触带岩体质量局部变差,出现破碎带,并控制了地下水局部富集和邻近低洼沟谷中泉水的生成。本研究揭示了山脊突变对地应力和岩体结构的影响,可望为类似条件下地质异常分析提供一定借鉴。     

运用结构面模拟技术分析岩体质量特征

在总结以往岩体质量分类经验基础上，突出岩体的结构特征分析与研究，阐明了岩体质量评价的理论、方法、指标体系，结合实例建立了一种简洁、实用的岩体质量评价体系。在这一系统中，突出了岩体结构面网络模拟分析在评价中对确定RQD值的重要作用，解决了RQD值的定量分析，对岩体质量评价向定量化发展具有重要意义。通过工程实践说明这一评价体系对工程建设具有重要指导作用。     

Fault detection in 3D by sequential Gaussian simulation of Rock Quality Designation (RQD)

Gazestan phosphate ore deposit (Central Iran) is an apatite deposit which is instrumental in selecting the method of excavation. The position of fault systems and the condition of rock quality also play a role in the method used for mineral resources and ore reserves estimation. Conversely, the Rock Quality Designation (RQD) is a parameter that provides a quantitative judgment of rock mass quality obtained from drill cores. This factor can be applied to detect the fractured zones which occur due to fault systems. Additionally, the faulted areas can be determined by surface geological map and a few by core drilling. Some of the faulted areas are not distinguishable in the surface and are covered by soils, especially within 3D modeling and visualization. In this study, an attempt has been made to establish a relationship between the RQD percentages which were geostatistically simulated and faulted areas through the region. In comparison, the results showed that low RQD domains (RQD <20 %) can be interpreted as fault zones; high RQD domains (RQD >50 %) correspond to less fractured areas, and the contact between high and low RQD domain is gradual. Therefore, this categorization of RQD domains can be incorporated to detect the faulted zones in 3D models for mine design. Based on the categorization, the uncertainty within the area was calculated to introduce two new core drilling points for the completion of this phase of exploratory grid from the fault structural viewpoint, in order to have a proper model of ore reserve to estimate. It was concluded that this procedure can be utilized for conceptual comprehension of fault trends in 3D modeling for the method selection of excavation and complete the estimation procedure phase.     

基于BQ系统的阿拉善巴彦诺日公NRG01号钻孔岩体质量评价

高放废物深部地质处置目前受到世界各国的高度重视,处置库围岩岩体质量评价是高放废物处置库选址的关键问题之一。文章基于BQ系统对我国高放废物地质处置库阿拉善预选区巴彦诺日公NRG01号钻孔进行了岩体质量评价。NRG01号孔钻孔资料丰富,采用岩芯编录、波速测井、水压致裂地应力测量及岩石波速测试、单轴压缩试验等多种方法手段相结合的方式获取了BQ评价系统中的各个参数。评价过程中,综合考虑了岩体坚硬程度、完整程度及地下水、软弱结构面、初始地应力等因素对围岩稳定的影响。根据计算的[BQ]值对岩体质量进行评价并与RQD评价结果进行对比。评价结果表明,NRG01号孔岩体质量较好,Ⅰ级和Ⅱ级岩体占90%,410~500 m的岩体范围可作为处置库建设的目标岩体。[BQ]值与RQD值所得的岩体质量评价结果一致性良好,但由于BQ系统考虑的影响因素更为全面,评价结果更为精细。本次评价可为巴彦诺日公地段高放废物地质处置库场址比选及处置库目标岩体选择提供依据。     

淮南板集煤矿F512断层导水性分析及地面注浆加固

板集煤矿F512断层落差70m,存在着导通上覆新生界松散层水与下伏太原组岩溶水的威胁,同时,断层带的破碎岩体也将对巷道掘进和支护带来困难。该矿先后施工了3个水文地质钻孔进行抽水和压水试验,根据岩心鉴定成果和岩石RQD值,认为断层带的岩心较为破碎;依据抽水过程中的流量变化、水位降深值和水位恢复值等指标及压水试验中透水率分析,发现该断层的导水性较差,具有弱渗透性。参考相邻矿区的经验,决定对断层破碎岩体采用地面注浆方法进行加固。整个工种注入水泥浆1 600m3,破碎岩体得到了有效加固,巷道掘进顺利通过了F512断层。     

Comparison of Permeability and Groutability of Ostur Dam Site Rock Mass for Grout Curtain Design

The focus of this study is the empirical hydromechanical behaviour of the Ostur dam site rock mass. The area surrounding the dam mostly consists of diorite and andesite, with primary fractures and hydrothermal veins. The hydromechanical behaviour of the rocks was determined using 500 water pressure tests at 5-m intervals. The hydrothermal veins and 2,739 discontinuities were studied and mapped along the dam axis. As a result, it was possible to design an optimum grout curtain for the dam axis. The empirical hydromechanical behaviour of the rock was studied to determine water flow and grout pressurised flow during the field tests that were conducted on two representative A-series grouting operation boreholes (one borehole for each abutment). The secondary permeability index (SPI), Lugeon value (LU), rock quality designation (RQD) and cement take (CT) values are presented and compared in this article. It is concluded that permeability and groutability are mostly controlled by the specifications and characteristics of the veins, especially in shallow areas and lower depths. A procedure is proposed based on a comparison of the trends in the RQD–SPI and LU–CT, and it is suggested that the areas with diverging trends require no treatment and that those with converging trends require heavy treatment. Additional complementary studies that were conducted during the construction stage have validated these results.     

一种基于块体化程度理论的裂隙岩体巷道顶板稳定性分级方法研究

岩体完整性是进行巷道顶板稳定性分级的一个重要指标,当前分级方法均是从一维角度对岩体结构进行描述,不能全面刻画出三维空间上顶板围岩的完整性。针对这一缺陷,引入裂隙岩体块体化程度理论,以块体化程度代替常规标准中表征岩体完整性的岩体质量RQD值和节理间距两项子指标,开展裂隙岩体巷道顶板稳定性分级研究,创新形成了一种适用于裂隙岩体顶板稳定性分级的BT分级方法。以块体百分比和块体体积曲线为基本依据,构建出裂隙岩体巷道顶板围岩块体化程度的解算流程;运用AHP法对稳定性影响因素权重进行了排序,制定出稳定性分级方法与标准。以铜坑矿92号矿体裂隙岩体试验区巷道顶板结构面调查数据和岩石力学参数为基础,运用传统分级方法RMR法和BT法分别对各试验区巷道顶板稳定性进行评价,对两种分级结果进行比较分析,结果表明：与传统的RMR法相比,BT法在稳定性描述、分级准确性和安全管理指导作用等方面更为优越,更能够客观真实地反映出裂隙岩体巷道顶板稳定性。研究成果可为复杂裂隙岩体条件下的巷道顶板安全分级与管理提供更为可靠的科学依据。