Behavior of soil plugs in open‐ended model piles driven into sands

Calibration chamber tests were conducted on open‐ended model piles driven into dried siliceous sands with different soil conditions in order to clarify the effect of soil conditions on load transfer mechanism in the soil plug. The model pile used in the test series was devised so that the bearing capacity of an open‐ended pile could be measured as three components: outside shaft resistance, plug resistance, and tip resistance. Under the assumption that the unit shaft resistance due to pile‐soil plug interaction varies linearly near the pile tip, the plug resistance was estimated. The plug capacity, which was defined as the plug resistance at ultimate condition, is mainly dependent on the ambient lateral pressure and relative density. The length of wedged plug that transfers the load decreases with the decrease of relative density, but it is independent of the ambient pressure and penetration depth. Under several assumptions, the value of earth pressure coefficient in the soil plug can be calculated. It gradually reduces with increase in the longitudinal distance from the pile tip. At the bottom of the soil plug, it tends to decrease with increase in the penetration depth and relative density, and to increase with the increase of ambient pressure. This may be attributed to (1) the decrease of friction angle as a result of increase in the effective vertical stress, (2) the difference in the dilation degree of the soil plug during driving with ambient pressures, and (3) the difference in compaction degree of soil plug during driving with relative densities. Based on the test results, an empirical equation was suggested to compute the earth pressure coefficient to be used in the calculation of plug capacity using one‐dimensional analysis, and it produces proper plug capacities for all soil conditions.     

Development of the cyclic p–y curve for a single pile in sandy soil

Pile foundations that support transmission towers or offshore structures are dominantly subjected to cyclic lateral load induced by wind and waves. For a successful design, it is crucial to investigate the effect of cyclic lateral loads on the pile behavior that is loaded laterally. Although the p–y curve method is generally utilized to design the cyclic laterally loaded pile foundations, the effect of cyclic lateral loads on the pile has not been properly implemented with the p–y curve. This reflects a lack of consideration of the overall stiffness change in soil–pile interaction. To address this, a series of model pile tests were conducted in this study on a preinstalled aluminum flexible pile under various sandy soil conditions. The test results were used to investigate the effect of cyclic lateral loads on the p–y behavior. The cyclic p–y curve, which properly takes into account this effect, was developed as a hyperbolic function. Pseudo-static analysis was also conducted with the proposed cyclic p–y curve, which showed that it was able to properly simulate cyclic laterally loaded pile behavior in sandy soil.     

Experimental Study on the Interaction Mechanism of Cap—Pile Group—Soil

Static load tests on pile group with prototype size were carried out in order to study the behavior and the working properties of the cap—pile group—soil interaction in the pile group foundation. The soil resistance under the cap, the pile shaft resistance and the tip resistance were measured by installing various measuring gauges. Based on these test results, the cap—pile group—soil interaction characteristics were analyzed. The regulations of the soil reaction on the cap, the shaft resistance and the tip resistance of pile, the mechanism of load transfer have been discussed with comparison to the result of the single pile tests. The bearing capacity of pile group is greater than the sum of the bearing capacity of the single pile obtained from testing in the same site in pile group foundation in the case presented here.     

A new look at the phenomenon of offshore pile plugging

Abstract

Open‐pipe piles are widely used for offshore structures. During the initial stage of installation, soil enters the pile at a rate equal to the pile penetration. As penetration continues, the inner soil cylinder may develop sufficient frictional resistance to prevent further soil intrusion, causing the pile to become plugged. The open‐ended pile then assumes the penetration characteristics of a closed‐ended pile. The mode of pile penetration significantly alters the soil‐pile interaction during and after installation. This affects the ultimate static bearing capacity (mainly in granular materials), the time‐dependent pile capacity (in clays), and the dynamic behavior and analysis of the piles.

Following a summary demonstrating the effects of pile plugging, a review of the common view of offshore pile plugging is undertaken. The interpretation of plugging by referring to the average plug length has led to the erroneous conclusion that in most piles significant plugging action does not occur.

Establishment of an analogy between soil samplers and open‐ended piles enabled correct identification of plugging by referring to the incremental changes in plug length. Examination of case histories of plugging of offshore piles revealed that beyond a certain penetration depth‐to‐diameter ratio, most piles are plugged.     

港口靠船桩工作性状计算的双参数法

港口靠船桩是承受重复性荷载或多循环荷载的一种横向承载桩。双参数法能较好地描述靠船桩 (单桩、群桩 )的桩土工作性状。用双参数法进行计算时 ,所给的地面条件必须由重复荷载或多循环荷载作用下实测出来。根据现场试桩资料 ,标定桩土参数 ,即k =mx1/n的指数l/n、桩土相对柔度系数α、桩土综合刚度EI等值 ,可以用来设计试桩附近局部地区同类条件下的其它长桩。对于没有进行试桩的某些工程 ,可以联合运用双参数法和p -y曲线法进行桩的分析     

Model tests on open-ended concrete pipe piles jacked in sand

Abstract

An experimental study of the performance of concrete pipe piles during installation under different penetration speeds and static load tests on the piles in sand is presented. The applied jacking force, the amount of pile penetration, length of soil plug formed and ultimate bearing capacity were measured during the model tests. The results showed that the concrete pipe piles were partially plugged and the behavior of the soil plug was significantly affected by the penetration speed. The lower the penetration speed, the larger the soil plug formed which in turn leads to a greater ultimate bearing capacity. The size of soil plug can be evaluated by the m value defined as the ratio of the volume of the soil plug to that of the penetrated pile wall. The relationship between the m value and the penetration speeds can be used to estimate the amount of soil plug and the depth of penetration for an open-ended concrete pipe pile jacked into sand.     

Lateral dynamic response of a partially embedded pile subjected to combined loads in saturated soil

In this article, an analytical solution is proposed to investigate the lateral dynamic response of a pile which is partially embedded in saturated soil layer and subjected to combined lateral and vertical loads. The saturated soil is described by Biot’s poroelastic theory and the resistance of soil is derived by potential function method. The governing equation of the pile is solved by coupling soil resistance and continuity conditions between the pile and the soil. The dynamic impedances of the pile are then obtained through transfer matrix method. To verify the validity of the proposed procedure, the present solution is compared with available solution for an idealized case. Finally, a parametric study is performed to investigate the effects of various parameters on the stiffness and damping properties of the pile-soil system. It is found that permeability of the soil and vertical load has significant effects on the dynamic response of the pile.     

A Model Test on the Behavior of a Static Drill Rooted Nodular Pile Under Compression

A static drill rooted nodular pile is a new type of composite pile foundation with high bearing capacity, and mud emissions can be largely reduced using the static drill rooted method. This report presents a model test on the behavior of this composite pile in a test box. The load-displacement response, axial force, skin friction, and mobilized base load are discussed in the report; in particular, the force in the cemented soil was investigated based on the measured data. Moreover, the finite element software ABAQUS was used to help investigate this behavior more thoroughly. It was determined that the function of the cemented soil around the pile shaft was different from that at the enlarged pile base; the stress in the cemented soil around the shaft increased suddenly when nearing the pile base; the ultimate skin friction obtained in the model test was larger than that estimated in the field test; and the relative displacement between the precast nodular pile and the cemented soil could be ignored during the loading process, which corresponded to the result of the field test and demonstrated that the nodular pile and cemented soil act as one entity during the loading process.     

土体疲劳对打桩分析的影响

在动力沉桩过程中,桩长时间连续运动导致桩侧土体强度的降低,使土体产生疲劳效应。结合一维应力波动理论,桩土相互作用模型和土体疲劳的不同计算方法,编制计算软件,对渤海某油田采油平台的桩基工程进行打桩分析,预测沉桩过程所需的锤击数、桩周土静阻力以及桩的极限承载力。比较不同的桩侧土体疲劳计算模式的分析结果,并用工程实测数据验证计算值。为工程设计和施工提供参考。     

Field Study on the Behavior of Destructive and Non-Destructive Piles Under Compression

This paper presents a series of full-scale load tests on long bored piles instrumented with strain gauges along the shafts, including eight field tests of piles loaded to failure and one non-destructive pile load test. The load-displacement response, skin friction, end resistance, and the threshold of the pile-soil relative displacement for fully mobilizing skin resistance were discussed. A simple softening model was proposed to describe the degradation behavior of the skin friction along the pile-soil interface and the load-displacement relationship developed at the pile base. It is found that the shaft resistance degradation investigated in the non-destructive load test only occurs at a shallow depth, and the skin friction of deeper soil is not fully developed. However, unlike the results of the non-destructive load tests, the softening is accompanied by a reduction in skin friction and observed to be along the whole pile depth. The thresholds of pile-soil relative displacement for fully mobilizing skin resistances in different soils have been found to be in the range 0.6% to 2.4% of the pile diameter. Moreover, in practical applications, a bilinear model is assumed to be feasible in analyzing the load-settlement relationship developed at the end of non-destructive pile, whereas the load transmission curve of the soils below the pile base corresponds to a softening model in the field tests of piles loaded to failure.     

有限元法在桩靴承载力计算中的应用

自升式钻井平台插桩是地基土在桩靴荷载作用下发生连续的塑性破坏的动态过程,当地基极限承载力等于桩靴荷载时插桩完成。经典土力学极限承载力理论对土体潜在滑动面做了假设,无法有效分析土体内部的破坏过程。本研究应用有限元法（FEM ）对插桩过程进行了模拟,得到地基土的破坏机制以及中间荷载下土体的应力、应变情况,通过和各理论公式计算的极限承载力进行对比分析,分析影响地基极限承载力的因素。研究表明,基础宽度与硬土层厚度的比值 B/H越大,下卧软土层越容易发生塑性破坏,极限承载力明显下降,当B/H＜0．286时,可以忽略下卧软土层对地基承载力的影响。     

A numerical investigation of influence of low-plasticity fines in sand on lateral response of piles

Abstract

Experimental evidence suggests that sands containing non-plastic or low-plasticity fines may show either decreasing or increasing shear strength with increasing fines content in certain situations. Accordingly, the presence of low-plasticity fines can significantly affect the ultimate lateral soil resistance; thus low-plasticity fines can affect the lateral response of piles. In this study, a quantitative method is proposed for determining the effect of low-plasticity fines in sand on the lateral response of piles in sand by combining a strain wedge model and a unified critical state compatible (UCSC) framework. An equivalent granular state parameter is employed in the UCSC framework to define the soil state uniquely in the strain wedge. The proposed quantitative method is incorporated in a finite element program. A series of numerical analyses are performed on a laterally loaded pile embedded in various relative densities of the base (clean) sand, to which various quantities of low-plasticity fines are added. The effect of low-plasticity fines on the lateral response is investigated. Furthermore, the effect of the low-plasticity fines on the response of the strain wedge is discussed.     

潮流作用下海洋平台桩基冲刷过程及冲刷深度计算

对埕岛油田典型平台周边多年监测所得的水深资料进行了分析研究,探讨了平台在潮流作用下的桩基冲刷过程及冲刷坑形态与分布,并选取经验公式对平台桩基极限冲刷深度进行了计算,计算结果与实测结果比较表明,所选公式在埕岛海域具有较好的适用性。     

Lateral loading of a pile using strain wedge model and its application under scouring

The scour hole around a pile will reduce the capacity of a laterally loaded pile. The strain wedge model is capable to derive a p–y curve for the analysis of a lateral loaded pile on a nonlinear Winkler foundation. To improve and extend the ability of the strain wedge method, a modified strain wedge (MSW) method is developed, in which a nonlinear lateral deflection of the pile is assumed to describe the varied soil strain distribution in the passive wedge. And then by treating the soil weight involved in the strain wedge as a vertical load at the bottom of the scour hole, an equivalent wedge depth is obtained to consider the effect of scour hole dimensions on the response of laterally loaded piles in sand. The validity of the MSW model is proved by comparisons with a centrifuge test without scour. And its applicability in the problem of a pile with scour is performed by a comparison with a model test and a FE analysis. The analysis shows the pile displacement at the pile head with scour can be obtained by multiplying the corresponding deflection without scour with an amplification factor related to scour depth at large load level.     

Implementation of state-dependent plasticity model in strain wedge model for laterally loaded piles in sand

ABSTRACT

The strain wedge model effectively performs nonlinear analyses of the lateral response of piles by using a nonlinear stress-strain relationship to describe soil behavior in the strain wedge. In this study, a state-dependent plasticity model has been implemented in the strain wedge model to calculate the stress-strain relationship for sand in the strain wedge. To complement this implementation, the effect of dilatancy on the shear strain is considered in the strain wedge. A full-scale test and a 45 g centrifuge model test on laterally loaded piles are used to validate the proposed method. The results show that the deflections and moments predicted by the proposed method accord well with those measured from full-scale and centrifugal model pile tests. Moreover, the combination of the state-dependent plasticity model and the strain wedge model allows for analyzing the lateral response of single piles using a unique set of model parameters for different relative densities of sands. In addtion, the stress-strain response in the strain wedge, not the dilatancy, dominates the soil resistance in the strain wedge and thus the lateral response of piles.     

多层砂土地基扩底桩单桩抗压模型试验及颗粒流模拟研究

利用室内半模试验和颗粒流数值模拟,揭示多层砂土地基扩底桩单桩抗压承载特性及变形特征。结果表明,通过对比分析极限承载力与H_h/D(持力层厚度与扩大头直径之比)的关系可以看出,单桩的抗压极限承载力随H_h/D逐渐增加,当H_h/D超过2.0时,极限承载力基本不再增加,此时的单桩抗压极限承载力稳定在300.01~303.25 N,是H_h/D=0.5时极限承载力(183.83 N)的1.65倍。扩大头下部土体发生局部压缩-剪切破坏,破坏面从扩大头底面边缘向斜下方扩展,在水平方向影响范围达到最大后逐渐向桩内侧收缩;荷载作用越大,地基破坏区域越大,相应的极限抗压承载力也越大;持力层厚度增加,扩大头分担的荷载比例增大,分担的荷载达到稳定需要的桩顶位移也越大,H_h=0.5 D试验扩大头分担的荷载比例稳定时为60%,对应的桩顶位移约为29 mm;桩顶位移达到33 mm后,H_h=1.0~3.0 D试验稳定在63%~65%之间;通过细观颗粒流理论对砂土移动特性的研究发现,持力层厚度从0.5 D增大至2.0 D,破坏面的起始扩展角度从31°增大至42°。数值模拟研究结果与模型试验数据吻合效果良好,证明该方法分析多层砂土地基扩底桩单桩抗压荷载传递机理是可行的。     

Shaft capacity of pre-bored grouted planted nodular pile under various overburden pressures in dense sand

Abstract

This paper presents the results of a series of model tests performed to study the shaft capacity of pre-bored grouted planted nodular (PGPN) pile in dense sand. The influence of the vertical overburden pressure on the shaft capacity of the PGPN pile is also investigated based on the test results. The test piles were equipped with strain gauges to measure the axial loads during the loading process, moreover, a foam plate was buried beneath pile tip to eliminate the influence of tip resistance on the shaft capacity. Some conclusions can be drawn based on the test results: the peak skin friction of PGPN pile increases with the increase of vertical overburden pressure applied on the foundation soil, while the rate of increase decreases with the increasing overburden pressure; the surface of the pile–soil interface of PGPN pile is relatively rough, and significant dilatant increase in lateral stress occurs during the loading process.     

Case study on pile running during the driving process of large-diameter pipe piles

The super-long and large-diameter steel pipe piles are often adopted for the construction of offshore oil platforms in deep sea. One constructability issue related to driving heavy pipe piles is the pile running. The term pile running refers to the quick penetration of a pile into the seabed as a result of its high self-weight and low resistance from the seabed. The unexpected pile running can cause the steel wire of the hammer to break or even the loss of the hammer. A case study of pile running at an oil platform is introduced in this paper. A simplified theoretical method is proposed to explain the mechanisms of the pile running in this case. A factor of friction degradation is proposed to calculate the dynamic skin friction from the static ultimate skin friction of surrounding soil. The comparisons between the predictions to the case history show that the proposed simplified method can be used to predict the pile running condition.     

Estimation of Axial Pile Bearing Capacity According to Shear Strength Parameters of Soil

At pesent,it is very popular to estimate pile bearing capacity by use of empirical formula andphysical indexes of soil provided in the design codes for civil construction in China.This paper attempts toapply mechanical indexes of soil and semi-empirical formulas,which are based on soil mechanical theoriesand were summarized and presented by Meyerhof in 1976,to calculate the axial pile bearing capacity.Lo-ading test results of 24 single piles in Tianjin area have been collected and compared with the proposed cal-ulation approach.     

Soil Plug Effect Prediction and Pile Driveability Analysis for Large-Diameter Steel Piles in Ocean Engineering

Long steel piles with large diameters have been more widely used in the field of ocean engineering.Owing to the pile with a large diameter,soil plug development during pile driving has great influences on pile driveability and beating capacity.The response of soil plug developed inside the open-ended pipe pile during the dynamic condition of pile-driving is different from the response under the static condition of loading during service.This paper addresses the former aspect.A numerical procedure for soil plng effect prediction and pile driveability analysis is proposed and described.By taking into consideration of the pile dimension effect on side and tip resistance,this approach introduces a dimensional coefficient to the conventional static equilibrium equations for the plug differential unit and proposes an improved static equity method for the plug effect prediction.At the same time,this approach introduces a simplified model by use of one-dimensional stress wave equation to simulate the interaction between soft ping and pile inner wall.The proposed approach has been applied in practical engineering analyses.Results show that the calculated plug effect and pile driveability based on the proposed approach agree well with the observed data.