Removal of Selenium Species from Waters Using Various Surface‐Modified Natural Particles and Waste Materials

Waste red mud and natural pumice/volcanic slag particles were surface modified and their selenium adsorption from waters was investigated. Acid activation/heat treatment of original red mud (ORM) particles significantly increased their micropore and external surface area and cumulative volume of pores. Iron oxide coating of pumice/slags and acid activation of ORM decreased their pH_pzc values and increased surface acidity. Selenite/selenate adsorption on iron oxide surfaces and acid activated red mud (AARM) was very fast with approximately first‐order adsorption kinetics. Iron oxide coating of pumice/slag and acid activation of ORM particles significantly enhanced their selenite and selenate uptakes. Maximum Se adsorption capacities as high as 6.3 (mg Se/g adsorbent) were obtained by AARM. The extent of selenate uptakes by the surface modified particles was generally lower than those of selenite. Due to competition among Se species and other background water matrix for iron oxide adsorption sites, reduced selenite/selenate uptakes were found in natural water compared to single solute tests. Higher Se uptakes by iron oxide surfaces were found at pH 7.5 compared to pH 8.9, due to increased electrostatic repulsion among iron oxides and Se species at higher pH. The most effective adsorbents among the tested 17 different particles for Se uptake were AARM and iron oxide coated pumice. Se concentrations less than drinking water standards (5–10 µg/L) can be achieved by these particles. These low‐cost, natural, or recyclable waste particles appear to be promising adsorbents for Se removal after their surface modification.     

Removal of Chromium from Synthetic Effluent using Nymphaea rubra

In the present work, biosorption of Cr(VI) by Nymphaea rubra was investigated in batch studies. Batch experiments were conducted to study the effect of initial sorbent dosage, solution pH and initial Cr(VI) concentration. The results showed that the equilibrium uptake capacity was increased with decrease in biomass dosage. The Cr(VI) removal was influenced by the initial chromium compound concentration. Langmuir and Freundlich adsorption isotherm models were used to represent the equilibrium data. The Freundlich isotherm model was fitted very well with the equilibrium data when compared to Langmuir isotherm model. The sorption results were analyzed for pseudo‐first order and pseudo‐second order kinetic model. It was observed that the kinetic data fitted very well with the pseudo‐second order rate equation when compared to the pseudo‐first order rate equation. Fourier transform infrared spectrum showed the presence of different functional groups in the biomass. The surface morphology of the sorbent was exemplified by SEM analysis. Aquatic weeds seem to be a promising biosorbent for the removal of chromium ions from water environment. This paper reports the research findings of a laboratory‐based study on the removal of Cr(VI) from the synthetic solution using the dried stem of N. rubra as a biosorbent.     

Development of Polymeric and Polymer‐Based Hybrid Adsorbents for Chromium Removal from Aqueous Solution

Ferric oxide‐loaded hybrid sorbents are environmentally benign and exhibit sorption behaviors for chromium removal from waters. In the current study, glycidyl methacrylate‐based polymer (GMD) and nanosized ferric oxide loaded glycidyl methacrylate‐based polymer (GMDFe) were prepared and assayed to examine the effect of ferric oxide loading on chromium sorption from aqueous solution for the first time from the equilibrium and kinetic points of view. The experimental equilibrium data, suitably fitted by the Langmuir and Freundlich isotherms, have shown that ferric oxide loaded hybrid sorbent exhibits higher adsorption capacity than glycidyl methacrylate‐based polymer (GMD). The Langmuir isotherm model was found to be the most suitable one for the Cr(VI) adsorption. The maximum adsorption capacities of GMD and GMDFe sorbents were determined at pH 4 as 109.54 and 157.52 mg/g, respectively. A series of column experiments was carried out to determine the breakthrough curves. The column was regenerated by eluting Cr(VI) using NaOH (10% w/v) solution after adsorption studies.     

Removal of EDTA from Aqueous Solutions Using Activated Carbon Prepared from Rubber Wood Sawdust: Kinetic and Equilibrium Modeling

Adsorptive removal of EDTA (ethylenediaminetetraacetic acid) from aqueous solution was studied using steam pyrolyzed activated carbon. Rubber wood sawdust, obtained from a local timber facility at Kodangavila, Trivandrum, Kerala, India was used as the precursor for the production of the activated carbon. Batch adsorption experiments were employed to monitor and optimize the removal process. The experimental parameters, i. e., solution pH, agitation time, initial EDTA concentration and adsorbent dosage, affecting the adsorption of EDTA onto sawdust activated carbon (SDAC) were optimized. The inner core mechanism for the interaction between EDTA and SDAC, which resulted in the adsorption process, was also discussed. The change in amount of EDTA adsorbed onto SDAC and CAC (commercial activated carbon) was compared over a wide range of pH (2.0–8.0). The maximum removal of EDTA took place in the pH range of 4.0–6.0 for SDAC and 5.0–5.5 for CAC, which demonstrates the effectiveness of the former adsorbent. Kinetic as well as equilibrium studies were performed to determine the rate constant and adsorption capacity, respectively. The adsorption kinetic data was fitted with pseudo‐first‐order kinetics and the equilibrium data was shown to follow the Langmuir isotherm model. These observations explain the formation of a monolayer of EDTA on the surface of SDAC as confirmed by the slow approach to equilibrium after 4 h of contact time. The adsorption capacity of SDAC for the removal of EDTA was 0.526 mmol/g and is seen to be greater than that of CAC and other reported adsorbents (0.193–0.439 mmol/g). Finally, it is clear that the production of steam pyrolyzed activated carbon in the presence of K₂CO₃ greatly enhanced EDTA removal and resulted in a product with possible commercial value for wastewater treatment strategies.     

Equilibrium Uptake and Bioaccumulation of Basic Violet 14 Using Submerged Macrophyte Hydrilla verticillata

The percentage removal and uptake capacity of Basic Violet 14 using Hydrilla verticillata with living biomass was studied under batch conditions. The survival of H. verticillata was studied using the chlorophyll content in the living biomass. Bioaccumulation of Basic Violet 14 using H. verticillata was tested by varying the wet sorbent dosage (0.5–2.5 g), initial pH (3–8), and initial dye concentrations (5–25 mg L^?1). The results show that the plant was effectively accumulating the Basic Violet 14 dye. The uptake capacity of Basic Violet 14 dye was observed as 5.9 and 21.3 mg g^?1 at the initial dye concentration of 5 and 25 mg L^?1, respectively, for a biomass of 5 g L^?1 (wet weight) at pH 7.0 for 144 h. In general, the plant growth was found to be normal at lower concentrations and showed higher removal efficiency. It was also observed that removal efficiency of H. verticillata was found to decrease with increase in initial dye concentration. The biomass sample surface was analyzed using SEM imaging and functional groups present in the biomass were analyzed using FTIR. The equilibrium uptake capacity was analyzed by Langmuir and Freundlich isotherms. The equilibrium data was found to be fit well to both Langmuir and Freundlich isotherm models with higher coefficient of determination.     

The Seashell Wastes as Biosorbent for Reactive Dye Removal from Textile Effluents

This study investigates structural and adsorption properties of the powdered waste shells of Rapana gastropod and their use as a new cheap adsorbent to remove reactive dye Brilliant Red HE‐3B from aqueous solutions under batch conditions. For the powder shells characterization, solubility tests in acidic solutions and X‐ray diffraction (XRD), scanning electron microscopy (SEM), energy‐dispersive X‐ray spectroscopy (EDX), Fourier transform IR spectroscopy (FT‐IR) and thermogravimetric analyses were performed. The results revealed that the adsorbent surface is heterogeneous consisting mainly from calcium carbonate layers (either calcite or aragonite) and a small amount of organic macromolecules (proteins and polysaccharides). The dye adsorptive potential of gastropod shells powder was evaluated as function of initial solution pH (1–5), adsorbent dose (6–40 g L^?1), dye concentration (50–300 mg L^?1), temperature (5–60°C), and contact time (0–24 h). It was observed that the maximum values of dye percentage removal were obtained at the initial pH of solution 1.2, shells dose of 40 g L^?1, dye initial concentration of 50–50 mg L^?1 and higher temperatures; the equilibrium time decreases with increasing of dye concentration. It is proved that the waste seashell powder can be used as low cost bioinorganic adsorbent for dyes removal from textile wastewaters.     

Batch and Continuous Design of a Full‐Scale Treatment Facility for Removing Dissolved Natural Organic Matter

Batch and continuous flow adsorption experiments are carried out and the design of a full‐scale facility for removing dissolved natural organic matter (DNOM) from Catalan Lakewater is demonstrated. The adsorption efficiency is proportional to the temperature and the amount of adsorbent unlike pH increase. The highest DNOM removal rate is obtained at 35 °C, pH 4, and an adsorbent amount of 0.8 g L^?1. Optimum contact time for batch studies is 60 min at equilibrium. Correlation constants (r) of Langmuir and Freundlich isotherms are 0.8905 and 0.9739, respectively. Based on the Freundlich isotherm, the highest adsorption capacity (q_max) obtained is 2.44 and 6.01 mg DNOM/g granulated activated carbon (GAC) for raw and enriched water, respectively. Consequently, the effects of adsorbent amount, bed depth, empty bed contact time, and organic loading on removal performance are investigated in the rapid small‐scale column test (RSSCT) columns. The targeted effluent concentration of 1 mg DNOM/L can easily be achieved in the columns. At the design capacity of the facility, 15 adsorption columns with dimensions of 7 m height, 4.33 m diameter, and 22 days of operation cycle are required to remove DNOM from raw water.     

Biosorption of Dyes by Natural and Activated Vine Stem. Interaction between Biosorbent and Dye

In the present study, the vine stem and modified vine stem were used as low cost adsorbents for the removal of acidic and basic dyes from aqueous solutions. A comparative study was also carried out with activated carbon obtained from vine stem and then the adsorption capacities of all adsorbents were evaluated by batch adsorption process. The effects of various adsorption parameters (initial pH, particle size, and contact time) were investigated. The modification of the vine stem with nitric acid increased its adsorption capacity for the basic dye. Both, vine stem and modified vine stem exhibited higher adsorption capacities than activated carbon. The adsorption capacities were found to be 322.58, 250, and 200 mg g^?1 for modified, natural vine stem, and activated carbon, respectively. In the case of acidic dye, the pH strongly affected the adsorption capacity and the maximum dye uptake was observed at pH 2 for all adsorbents. The acidic dye adsorption was lower compared to basic dye on both biosorbents and activated carbon tested. The maximum acidic dye adsorption values (58.82 and 59.88 mg g^?1) were obtained with the vine stem and activated carbon, respectively. In the case of lignocellulosic adsorbents, both surface charge and surface groups had main effect on the adsorption of basic dye, while adsorption mechanism in activated carbon was mainly through the physical adsorption. The results of comparative adsorption capacity of adsorbents indicated that vine stem or modified vine stem can be used as a low cost alternative to activated carbon in aqueous solution for basic dye removal.     

Effect of extracellular polymeric substances on the phosphorus adsorption characteristics of sediment particles

Extracellular polymeric substances (EPS) have a great impact on the characteristics of sediment particles and their environmental effects in hydro-environmental systems, yet little effort has been made to study the considerable variability in the element adsorption process of sediment particles caused by EPS. Understanding the variability of the adsorption characteristics of sediment particles associated with EPS and quantifying the scale of the adsorption isotherm parameters are important for understanding how EPS mediate sediment properties and environmental factors. In this paper, isothermal equilibrium adsorption experiments are done on phosphorus to study the influence of EPS on the adsorption characteristics of sediment particles, and the Langmuir adsorption isotherm is applied to analyze the adsorption rule of sediment particles under the impact of EPS. The current research demonstrates that significant differences will take place in the adsorption characteristics of sediments coated with EPS at different development phases and the phosphorus adsorption capacity of sediment particles increases with the growth of EPS. The difference in the adsorption percentage between sediment particles coated with EPS of 0 and 6 weeks growth time is about 42%–60% for different initial aqueous phosphorus concentration. A formula describing the adsorption isotherm parameter of the maximum material (element) adsorption capacity of sediment particles change over time is further proposed based on the experimental data. The current study provides some evidence for the interaction of sediment particles, EPS, and adsorbed elements in the water environment.     

Adsorption of Zinc using Tea Factory Waste: Kinetics,Equilibrium and Thermodynamics

In India, the annual production of tea is ca. 857,000 tonnes, which is 27.4% of the total world production. The amount of tea factory waste (TFW) produced per annum after processing is ca. 190,400 tonnes. TFW can be used as a low cost adsorbent for the removal of toxic metals from the aqueous phase. An investigation was carried out to study the feasibility of the use of TFW as an adsorbent for the removal of the heavy metal, zinc. Equilibrium, kinetic and thermodynamic studies were reported. The straight line plot of log (q_e–q) versus time t for the adsorption of zinc shows the validity of the Lagergren equation. The various steps involved in adsorbate transport from the solution to the surface of the adsorbent particles were dealt with by using a Weber‐Morris plot, q_e versus t^0.5 for the TFW. The rate controlling parameters, k_id,1 and k_id,2, were determined and it was found that the macro‐pore diffusion rate was much larger than micro‐pore diffusion rate. A batch sorption model, which assumes the pseudo‐second‐order mechanism, was used to predict the rate constant of sorption, the equilibrium sorption capacity and the initial sorption rate with the effect of initial zinc (II) ion concentration. Equilibrium data obtained from the experiments were analyzed with various isotherms, i. e., Freundlich, Langmuir, Redlich‐Peterson and Tempkin. The adsorption equilibrium was reached in 30 min and the adsorption data fitted well to all models. The maximum adsorption capacity of TFW for zinc (II) ions was determined to be 14.2 mg/g. The capacity of adsorption on Zn(II) increased with increasing temperatures and pH. The maximum uptake level of zinc was observed at pH of 4.2. The various thermodynamic parameters, i. e., ΔG°, ΔH° and ΔS°, were estimated. The thermodynamics of the zinc ion/TFW system indicated a spontaneous, endothermic and random nature of the process. The results showed that the TFW, which has low economical value, is a suitable adsorbent for the removal of zinc (II) ions from aqueous solutions.     

Studies on the Removal of Iron from Drinking Water by Electrocoagulation – A Clean Process

The present study describes an electrocoagulation process for the removal of iron from drinking water using magnesium as the anode and galvanized iron as the cathode. Experiments were carried out as a function of pH, temperature and current density. The adsorption capacity was evaluated using both the Langmuir and the Freundlich isotherm models. The results show that the maximum removal efficiency of 98.4% was achieved at a current density of 0.06 A dm^–2, at a pH of 6.0. The adsorption of iron was better explained by fitting the Langmuir adsorption isotherm, which suggests a monolayer coverage of adsorbed molecules. The adsorption process followed a second‐order kinetics model. Temperature studies showed that adsorption was endothermic and spontaneous in nature.     

Adsorption of Thallium(I) Ions Using Eucalyptus Leaves Powder

Using batch method, the adsorption of thallium(I) ions from aqueous solutions on eucalyptus leaves powder, as a low cost adsorbent, was studied. The effect of various modification of considered adsorbent on the adsorption percentage of Tl(I) is an important feature of this study. The results showed that the unmodified and acidic modified adsorbent are the poor adsorbents for the Tl(I) ions while basic modified adsorbent is a suitable adsorbent. Also, the effect of some experimental conditions such as solution initial pH, agitation speed, contact time, sorbent dosage, temperature, particle size, and thallium initial concentration was studied. The results showed that the adsorption percentage depends on the conditions and the process is strongly pH‐dependent. The satisfactory adsorption percentage of Tl(I) ions, 81.5%, obtained at 25 ± 1°C. The equilibrium data agreed fairly better with Langmuir isotherm than Freundlich and Temkin models. The value of q_m that was obtained by extrapolation method is 80.65 mg g^?1. Separation factor values, R_L, showed that eucalyptus leaves powder is favorable for the sorption of Tl(I). The negative values of ΔH⁰ and ΔS⁰ showed that the Tl(I) sorption is an exothermic process and along with decrease of randomness at the solid–solution interface during sorption, respectively.     

Characterization of phosphorus interaction with sediments affected by acid mine drainage-relation with the sediment composition

Phosphorus sorption capacity was investigated in surface sediments derived from an abandoned zinclead mine area located in northeastern Algeria. The forms and the distribution of phosphorus in the raw sediment were identified using the sequential chemical extractions method. Batch experiments were done to study the adsorption kinetics and isotherms. The pH effect was evaluated by macroscopic and infrared analyses. In raw sediment, speciation results show that phosphorus is dominantly bound to oxyhydroxides. Sorption experiments demonstrate that phosphorus uptake is principally related to sediment composition. The nature of the dominant iron oxyhydroxide has a substantial role in the adsorption capacity and the mechanism interaction. The adsorption kinetics can be described by the second order and Elovich models. The isotherms data are successfully modeled by the Temkin equation.The maximum phosphorus removal is reached under acidic pH. Spectroscopic analyses reveal that the predominance of jarosite implies electrostatic interaction with sediment particles. However, in the case of schwertmannite predominance, phosphate ions are adsorbed by the ligand exchange mechanism.     

Adsorption Characteristics of Reactive Black 5 from Aqueous Solution onto Chitosan

Adsorption of reactive black 5 (RB5) from aqueous solution onto chitosan was investigated in a batch system. The effects of solution pH, initial dye concentration, and temperature were studied. Adsorption data obtained from different batch experiments were modeled using both pseudo first‐ and second‐order kinetic equations. The equilibrium adsorption data were fitted to the Freundlich, Tempkin, and Langmuir isotherms over a dye concentration range of 45–100 µmol/L. The best results were achieved with the pseudo second‐order kinetic and Langmuir isotherm equilibrium models, respectively. The equilibrium adsorption capacity (q_e) was increased with increasing the initial dye concentration and solution temperature, and decreasing solution pH. The chitosan flakes for the adsorption of the dye was regenerated efficiently through the alkaline solution and was then reused for dye removal. The activation energy (E_a) of sorption kinetics was estimated to be 13.88 kJ/mol. Thermodynamic parameters such as changes in free energy (ΔG), enthalpy (ΔH), and entropy (ΔS) were evaluated by applying the van't Hoff equation. The thermodynamics of reactive dye adsorption by chitosan indicates its spontaneous and endothermic nature.     

Malachite Green Removal from Aqueous Solution by the Peel of Cucumis sativa Fruit

This study investigates the potential use of activated carbon prepared from the peel of Cucumis sativa fruit for the removal of malachite green (MG) dye from simulated wastewater. The effects of different system variables, adsorbent dosage, initial dye concentration, pH, and contact time were investigated and optimal experimental conditions were ascertained. The results showed that when the amount of the adsorbent increased, the percentage of dye removal increased accordingly. Optimum pH value for dye adsorption was 6.0. Maximum dye was sequestered within 50 min of the start of every experiment. The adsorption of MG followed the pseudo‐second‐order rate equation and fits the Langmuir, Freundlich, Dubinin–Radushkevich (D–R), and Tempkin equations well. The maximum removal of MG was obtained at pH 6 as 99.86% for adsorbent dose of 1 g/50 mL and 25 mg L^?1 initial dye concentration at room temperature. Activated carbon developed from the peel of C. sativa fruit can be an attractive option for dye removal from diluted industrial effluents since test reaction made on simulated dyeing wastewater showed better removal percentage of MG.     

Use of Pistachio Shells as an Adsorbent for the Removal of Zinc(II) Ion

In this study, the removal of zinc(II) ion from an aqueous solution by pistachio shells (PS) is investigated. The dynamic behavior of the adsorption is examined on the effects of pH, adsorbent dosage, and contact time. The adsorption rates are determined quantitatively and simulated by the Lagergren first order, pseudo‐second order, Elovich, and intra‐particle diffusion kinetic models. The adsorption kinetic models are also tested for validity. The thermodynamic parameters, which are also deduced from adsorption experiments, are very useful in elucidating the nature of adsorption. The experimental results reveal that the optimum pH value and the contact time for the adsorption of Zn²⁺ onto PS are found as 6 and 10 min, respectively. According to these parameters, adsorption process follows the pseudo‐second order kinetic model with high correlation coefficients (R² = 0.999). The obtained results demonstrate that PS is a reasonably effective adsorbent for the removal of Zn²⁺ from aqueous leachate of hazardous waste.     

Application of Agro‐Based Biomasses for Zinc Removal from Wastewater – A Review

Zinc remediation of aqueous streams is of special concern due to its highly toxic and persistent nature. Conventional treatment technologies for the removal of zinc are not economical and further generate huge quantity of toxic chemical sludge. Biosorption is emerging as a potential alternative to the existing conventional technologies for the removal of metal ions from aqueous solutions. Mechanisms involved in the biosorption process include chemisorption, complexation, adsorption–complexation on surface and pores, ion exchange, microprecipitation, heavy metal hydroxide condensation onto the bio surface, and surface adsorption. Biosorption largely depends on parameters such as pH, the initial metal ion concentration, biomass concentration, presence of various competitive metal ions in solution, and to a limited extent on temperature. Biosorption using biomass such as agricultural wastes, industrial residues, municipal solid waste, biosolids, food processing waste, aquatic plants, animal wastes, etc., is regarded as a cost‐effective technique for the treatment of high volume and low concentration complex wastewaters containing zinc metal. Very few reviews are available where readers can get an overview of the sorption capacities of agro based biomasses used for zinc remediation together with the traditional remediation methods. The purpose of this review article is to provide the scattered available information on various aspects of utilization of the agro based biomasses for zinc metal ions removal. An extensive table summarizes the sorption capacities of various adsorbents. These biosorbents can be modified using various methods for better efficiency and multiple reuses to enhance their applicability at industrial scale. We have incorporated most of the valuable available literature on zinc removal from waste water using agro based biomasses in this review.     

Assessment of the Biosorption Characteristics of a Spent Cottonseed Husk Substrate for the Decolorization of Methylene Blue

This study concentrates on the possible application of the spent cottonseed husk substrate (SCHS), an agricultural waste used after the cultivation of white rot fungus Flammulina velutipes, to adsorb methylene blue (MB) from aqueous solutions. Batch studies were carried out with variable initial solution pH, adsorbent amount, reaction time, temperature, and initial MB concentration. MB uptake was favorable at pH ranging from 4.0 to 12.0, and the equilibrium adsorption capacity of 143.5 mg g^?1 can be reached promptly within about 240 min. The combination analysis of FTIR and BET techniques revealed that the massive functional groups on the biosorbent surface, such as hydroxyl and carboxyl, were responsible for the biosorption of MB. It was found that adsorption data matched the pseudo‐second order kinetic and Langmuir isotherm models. Thermodynamic parameters of free energy (ΔG°), enthalpy (ΔH°), and entropy (ΔS°), obtained from biosorption MB ranging from 293 to 313 K, showed that the sorption experiment was a spontaneous and endothermic process. The study highlighted a new pathway to develop a new potential utilization of SCHS as a low‐cost sorbent for the removal of MB pollutants from wastewater.     

Adsorption characteristics of copper ion on nanoporous silica

Adsorption by nanoporous media is critically involved in many fundamental geological and geochemical processes including chemical weathering,element migration and enrichment,environmental pollution,etc.Yet,the adsorption behavior of metal ions on nanoporous materials has not been systematically investigated.In this study,MCM-41 material with a monodisperse pore size(4.4 nm)and a large BET specific surface area(839 m^2/g)was hydrothermally prepared and used as a model silica adsorbent to study the adsorption characteristics of Cu^2+as a representative metal ion.The Cu^2+adsorption capacity was found to increase with increasing suspension pH in the range from 3 to 5 and to decrease in the presence of NaNO3.At 25℃,pH=5,and a solid-to-liquid ratio of 5 g/L,the adsorption capacity was determined to be 0.29 mg/g,which can be converted to a dimensionless partition coefficient of 45,indicating a strong enriching effect of nanoporous silica.The adsorption isotherm and kinetic data were fitted to several commonly used thermodynamic,kinetic,and diffusion models.The adsorption mechanism was also studied by Fourier transform infrared spectroscopy,X-ray photoelectron spectroscopy and synchrotron-based X-ray absorption spectroscopy.The results suggest that Cu2+ion adsorption is an entropy-driven endothermal process,possibly involving both outer-sphere and inner-sphere complexes.