Hydrocarbon charging and accumulation history in the Niudong Buried Hill Field in the Baxian Depression,eastern China

The Niudong Buried Hill Field, which lies in the Baxian Depression of the Bohai Bay Basin, is the deepest oil/gas accumulation in eastern China. Its Precambrian dolomite reservoir occurs at burial depths of 5860 m–6027 m. This paper attempts to document the hydrocarbon charging and accumulation history in this field, which could greatly enhance the understanding of the mechanisms for the formation of deep hydrocarbon accumulations. Our previous study of oil trapped in fluid inclusions has demonstrated that the ratio parameters of the fluorescence spectral intensities at 425 nm and 433 nm (Q_425/433 ratio), and at 419 nm and 429 nm (Q_419/429 ratio) can be more effective for revealing hydrocarbon charging history than the previously-used fluorescence parameters such as Lambda max and red/green quotient as well as fluorescence colors. The hydrocarbon charging and accumulation history in the Niudong Buried Hill Field was studied with an integrated approach involving the application of these two spectral parameters of petroleum inclusion fluorescence as well as utilization of other data including homogenization temperatures of aqueous inclusions coeval with petroleum inclusions, and cross-cutting relationships of cements and “oil veins” in pores and fractures. The results indicate that the dolomite reservoir in the Niudong Buried Hill Field experienced three episodes of hydrocarbon charging. In the first two episodes (between 38.5Ma and 25Ma), the low mature and mature oils, which were derived from source rocks in the Sha-4 Member of the Eocene Shahejie Formation, migrated into the reservoir, but part of them leaked out due to normal faulting at the updip margin of the buried hill. These early-charged oils were preserved mainly in small pores in micritic dolomites by oil-wettability and capillary pressure. In the Neogene, the basin subsided as a whole and local faults at the updip margin became inactive and played a sealing role. By approximately 13Ma, the source rocks became highly mature and the generated hydrocarbons then migrated into the reservoir and accumulated. Therefore, the last charging is the most important for hydrocarbon accumulation in the Niudong Buried Hill Field.     

Oil-bearing inclusions in vein quartz and calcite and,bitumens in veins: Testament to multiple phases of hydrocarbon migration in the Barrandian basin (lower Palaeozoic), Czech Republic

The petroleum charge history of the Barrandian basin was investigated by analysing quartz and calcite and organic phases that occur in veins and fractures cutting dolerite sills within the Liteň Formation (Silurian). The geochemical characteristics of fluid inclusions trapped in vein quartz and calcite, vein bitumens and adjacent potential source rocks when combined with burial and thermal history data reflect the presence of at least three separate hydrocarbon charge episodes. Solid highly reflecting (R_max = 0.92–1.49%) bitumen provides information on the first and oldest episode of oil migration. The precursor oil was probably derived relatively early during diagenesis from nearby organic-rich sediments and was subsequently thermally altered to form the solid bitumen.     

Tracing of deeply-buried source rock: A case study of the WC9-2 petroleum pool in the Pearl River Mouth Basin, South China Sea

The identification of a deeply-buried petroleum-source rock, owing to the difficulty in sample collection, has become a difficult task for establishing its relationship with discovered petroleum pools and evaluating its exploration potential in a petroleum-bearing basin. This paper proposes an approach to trace a deeply-buried source rock. The essential points include: determination of the petroleum-charging time of a reservoir, reconstruction of the petroleum generation history of its possible source rocks, establishment of the spatial connection between the source rocks and the reservoir over its geological history, identification of its effective source rock and the petroleum system from source to trap, and evaluation of petroleum potential from the deeply-buried source rock. A case study of the W9-2 petroleum pool in the Wenchang A sag of the Pearl River Mouth Basin, South China Sea was conducted using this approach. The W9-2 reservoir produces condensate oil and gas, sourced from deeply-buried source rocks. The reservoir consists of a few sets of sandstone in the Zhuhai Formation, and the possible source rocks include an early Oligocene Enping Formation mudstone and a late Eocene Wenchang Formation mudstone, with a current burial depth from 5000 to 9000 m. The fluid inclusion data from the reservoir rock indicate the oil and the gas charged the reservoir about 18–3.5 Ma and after 4.5 Ma, respectively. The kinetic modeling results show that the main stages of oil generation of the Wenchang mudstone and the Enping mudstone occurred during 28–20 Ma and 20–12 Ma, respectively, and that the δ¹³C₁ value of the gas generated from the Enping mudstone has a better match with that of the reservoir gas than the gas from the Wenchang mudstone. Results from a 2D basin modeling further indicate that the petroleum from the Enping mudstone migrated upward along the well-developed syn-sedimentary faults in the central area of the sag into the reservoir, but that the petroleum from the Wenchang mudstone migrated laterally first toward the marginal faults of the sag and then migrated upward along the faults into shallow strata. The present results suggest that the trap structure in the central area of the sag is a favorable place for the accumulation of the Enping mudstone-derived petroleum, and that the Wenchang mudstone-derived petroleum would have a contribution to the structures along the deep faults as well as in the uplifted area around the sag.     

Improved understanding of petroleum migration history in the Hongche fault zone,northwestern Junggar Basin (northwest China): Constrained by vein-calcite fluid inclusions and trace elements

Calcite veins and cements occur widely in Carboniferous and Permian reservoirs of the Hongche fault zone, northwestern Junggar Basin in northwest China. The calcites were investigated by fluid inclusion and trace-element analyses, providing an improved understanding of the petroleum migration history. It is indicated that the Hongche fault behaved as a migration pathway before the Early Cretaceous, allowing two oil charges to migrate into the hanging-wall, fault-core and footwall reservoirs across the fault. Since the Late Cretaceous, the Hongche fault has been sealed. As a consequence, meteoric water flowed down only into the hanging-wall and fault-core reservoirs. The meteoric-water incursion is likely an important cause for degradation of reservoir oils. In contrast, the footwall reservoirs received gas charge (the third hydrocarbon event) following the Late Cretaceous. This helps explain the distribution of petroleum across the fault. This study provides an example of how a fault may evolve as pathway and seal over time, and how reservoir diagenetic minerals can provide clues to complex petroleum migration histories.     

Stable carbon isotope ratios of CH4-rich gas inclusions in shale-hosted fracture-fill mineralization: A tool for tracing hydrocarbon generation and migration in shale plays for oil and gas

Fluid inclusion gases in minerals from shale hosted fracture-fill mineralization have been analyzed for stable carbon isotopic ratios of CH₄ using a crushing device interfaced to an isotope ratio mass spectrometer (IRMS). The samples of Paleozoic strata under study originate from outcrops and wells in the Rhenish Massif and Campine Basin, Harz Mountains, and the upper slope of the Southern Permian Basin. Fracture-fill mineralization hosted by Mesozoic strata was sampled from drill cores in the Lower Saxony Basin. Some studied sites are candidates for shale gas exploration in Germany. Samples of Mesozoic strata are characterized by abundant calcite-filled horizontal fractures which preferentially occur in TOC-rich sections of the drilled sediments. Only rarely are vertical fractures filled with carbonates and/or quartz in drill cores from Mesozoic strata but in Paleozoic shale they occur frequently. The δ¹³C(CH₄) values of fluid inclusions in calcite from horizontal fractures hosted by Mesozoic strata suggest that gaseous hydrocarbons were generated during the oil/early gas window and that the formation of horizontal fractures seems to be related to hydraulic expulsion fracturing. The calculated maturity of the source rocks at the time of gas generation lies below the maturity derived from measured vitrinite reflectance. Thus, the formation of horizontal fractures and trapping of gas that was generated in the oil and/or early gas window obviously occurred prior to maximal burial. Rapidly increasing vitrinite reflectance data seen locally can be explained by hydrothermal alteration, as indicated by increasing δ¹³C (CH₄–CO₂) values in fluid inclusions. The formation of vertical fractures in studied Mesozoic sediments is related to stages of post-burial inversion; gas-rich inclusions in fracture filling minerals recorded the migration of gas that had probably been generated instantaneously, rather than cumulatively, from high to overmature source rocks. Since no evidence is given for the presence of early generated gas in studied Paleozoic shale, it appears likely that major gas loss from shales occurred due to deformation and uplift of these sediments in response to the Variscan Orogeny.     

Petroleum generation and charge history of the northern Dongying Depression,Bohai Bay Basin,China: Insight from integrated fluid inclusion analysis and basin modelling

The petroleum generation and charge history of the northern Dongying Depression, Bohai Bay Basin was investigated using an integrated fluid inclusion analysis workflow and geohistory modelling. One and two-dimensional basin modelling was performed to unravel the oil generation history of the Eocene Shahejie Formation (Es3 and Es4) source rocks based on the reconstruction of the burial, thermal and maturity history. Calibration of the model with thermal maturity and borehole temperature data using a rift basin heat flow model indicates that the upper interval of the Es4 source rocks began to generate oil at around 35 Ma, reached a maturity level of 0.7% R_o at 31–30 Ma and a peak hydrocarbon generation at 24–23 Ma. The lower interval of the Es3 source rocks began to generate oil at around 33–32 Ma and reached a maturity of 0.7% R_o at about 27–26 Ma. Oil generation from the lower Es3 and upper Es4 source rocks occurred in three phases with the first phase from approximately 30–20 Ma; the second phase from approximately 20–5 Ma; and the third phase from 5 Ma to the present day. The first and third phases were the two predominant phases of intense oil generation.Samples from the Es3 and Es4 reservoir intervals in 12 wells at depth intervals between 2677.7 m and 4323.0 m were investigated using an integrated fluid inclusion workflow including petrography, fluorescence spectroscopy and microthermometry to determine the petroleum charge history in the northern Dongying Depression. Abundant oil inclusions with a range of fluorescence colours from near yellow to near blue were observed and were interpreted to represent two episodes of hydrocarbon charge based on the fluid inclusion petrography, fluorescence spectroscopy and microthermometry data. Two episodes of oil charge were determined at 24–20 Ma and 4–3 Ma, respectively with the second episode being the predominant period for the oil accumulation in the northern Dongying Depression. The oil charge occurred during or immediately after the modelled intense oil generation and coincided with a regional uplift and a rapid subsidence, suggesting that the hydrocarbon migration from the already overpressured source rocks may have been triggered by the regional uplift and rapid subsidence. The expelled oil was then charged to the already established traps in the northern Dongying Depression. The proximal locations of the reservoirs to the generative kitchens and the short oil migration distance facilitate the intimate relationship between oil generation, migration and accumulation.     

Controls on reservoir quality of Lower Cretaceous tight sandstones in the Laiyang Sag,Jiaolai Basin,Eastern China: Integrated sedimentologic,diagenetic and microfracturing data

The Jiaolai Basin (Fig. 1) is an under-explored rift basin that has produced minor oil from Lower Cretaceous lacustrine deltaic sandstones. The reservoir quality is highly heterogeneous and is an important exploratory unknown in the basin. This study investigates how reservoir porosity and permeability vary with diagenetic minerals and burial history, particularly the effects of fracturing on the diagenesis and reservoir deliverability. The Laiyang sandstones are tight reservoirs with low porosity and permeability (Φ < 10% and K < 1 mD). Spatial variations in detrital supply and burial history significantly affected the diagenetic alterations during burial. In the western Laiyang Sag, the rocks are primarily feldspathic litharenites that underwent progressive burial, and thus, the primary porosity was partially to completely eliminated as a result of significant mechanical compaction of ductile grains. In contrast, in the eastern Laiyang Sag, the rocks are lithic arkoses that were uplifted to the surface and extensively eroded, which resulted in less porosity reduction by compaction. The tectonic uplift could promote leaching by meteoric water and the dissolution of remaining feldspars and calcite cement. Relatively high-quality reservoirs are preferentially developed in distributary channel and mouth-bar sandstones with chlorite rims on detrital quartz grains, which are also the locations of aqueous fluid flow that produced secondary porosity. The fold-related fractures are primarily developed in the silt–sandstones of Longwangzhuang and Shuinan members in the eastern Laiyang Sag. Quartz is the most prevalent fracture filling mineral in the Laiyang sandstones, and most of the small-aperture fractures are completely sealed, whereas the large-aperture fractures in a given set may be only partially sealed. The greatest fracture density is in the silt–sandstones containing more brittle minerals such as calcite and quartz cement. The wide apertures are crucial to preservation of the fracture porosity, and the great variation in the distribution of fracture-filling cements presents an opportunity for targeting fractures that contribute to fluid flow.     

A well-preserved 250 million-year-old oil accumulation in the Tarim Basin,western China: Implications for hydrocarbon exploration in old and deep basins

A giant oilfield (YM-2) with an estimated reserve of close to one billion bbl was recently discovered in an Ordovician carbonate reservoir at a burial depth of 5800–6200 m in the northern Tarim Basin, western China. Biomarker and isotope geochemistry of the hydrocarbons indicate that the oil was derived from Ordovician marine source rocks at early to peak oil generation. Authigenic illite (K–Ar) dating, fluid inclusion analysis, fluid inclusion PVTx and thermal history modeling indicate that the accumulation is of primary in origin, and the original charge occurred in the Permian during the Late Hercynian Orogenic Stage, approximately 290–250 million years ago. The physiochemical compositions of the hydrocarbons and formation water remained largely unchanged since the initial accumulation. The excellent preservation of such an old accumulation at such a great depth is due to continuous burial of the YM-2 structure since the Triassic, a thick effective seal, and a relatively low geothermal gradient with a current reservoir temperature of 127–130 °C. This finding suggests that under suitable conditions old petroleum accumulations can be well-preserved, and some old and deep basins may be prospective frontiers for future exploration.     

Structural patterns of the late Mesozoic crustal detachment system in the Raoyang Sag,Bohai Bay Basin,eastern China: New insights from 3D seismic data

Understanding the late Mesozoic tectonic origin and structural patterns of the Bohai Bay Basin (BBB) is of growing importance for its buried-hill petroleum exploration. This study revealed, based on 3D seismic and borehole data, that the Raoyang Sag in the Jizhong Depression, western BBB, was dominated by a crustal detachment system during the late Jurassic to the early Cretaceous. It was characterized by the WNW-dipping low-angle detachment fault F₀ (namely Cangxi Fault), the structural dome cored by Archean Basement rocks at the footwall and supradetachment basins on the hanging wall. We suggested the late Mesozoic volcanic materials and coarse deposits accumulated in the supradetachment basins had locally diminished the petroleum prospect, but the syndetachment deformation and denudation had contributed to it by means of promoting petroleum migration from source rocks to reservoirs and improving porosity and permeability of the reservoir rocks by karstification and structural fracturing.     

Oil migration driven by exhumation of the Canol Formation oil shale: A new conceptual model for the Norman Wells oil field,northwestern Canada

Thermal history, petroleum system, structural, and tectonic constraints are reviewed and integrated in order to derive a new conceptual model for the Norman Wells oil field, and a new play type for tectonically active foreland regions. The thermal history recorded by Devonian rocks suggests that source rocks experienced peak thermal conditions in the Triassic–Jurassic, during which time oil was likely generated. After initial oil generation and expulsion, the Canol Formation oil shale retained a certain fraction of hydrocarbons. The shallow reservoir (650–350 m) is a Devonian carbonate bank overlain by the Canol Formation and resides within a hanging wall block of the Norman Range thrust fault. Both reservoir and source rocks are naturally fractured and have produced high API non-biodegraded oil. Thrust faults in the region formed after the Paleocene, and a structural cross-section of the field shows that the source and reservoir rocks at Norman Wells have been exhumed by over 1 km since then.The key proposition of the exhumation model is that as Canol Formation rocks underwent thrust-driven exhumation, they crossed a ductile–brittle transition zone and dip-oriented fractures formed sympathetic to the thrust fault. The combination of pore overpressure and new dip-directed subvertical fractures liberated oil from the Canol Formation and allowed for up-dip oil migration. Reservoir rocks were similarly fractured and improved permeability enhanced charging and pooling of oil. GPS and seismicity data indicate that strain transfer across the northern Cordillera is a response to accretion of the Yakutat terrane along the northern Pacific margin of North America, which is also the probable driving force for foreland shortening and rock exhumation at Norman Wells.     

Characteristics and petroleum origin of the Carboniferous volcanic rock reservoirs in the Shixi Bulge of Junggar Basin,western China

Shixi Bulge of the central Junggar Basin in western China is a unique region that provides insight into the geological and geochemical characteristics of large-scale petroleum reservoirs in volcanic rocks of the western Central Asian Orogenic Belt. Carboniferous volcanic rocks in the Shixi Bulge mainly consist of striped lava and agglomerate, as well as breccia lava and tight tuff. Volcanic rocks differ in porosity and permeability. Striped lava exhibits the highest porosity (average: 14.2%) but the lowest permeability (average: 0.67 × 10⁻¹⁵ m) among the rock types. Primary gas pores are widely developed and mostly filled. Secondary dissolution pores and fractures are two major reservoir storage spaces. Capillary pressure curves suggest the existence of four pore structure types of reservoir rocks. Several factors, namely, lithology, pore structure, and various diagenesis, govern the physical properties of volcanic rocks. The oil is characterized by a high concentration of tricyclic terpane, a terpane distribution of C₂₃ < C₂₁ > C₂₀, and sterane distributions of C₂₇ < C₂₈ < C₂₉ and C₂₇ > C₂₈ < C₂₉. Oil and gas geochemistry revealed that the oil is a mixture derived primarily from P₂w source rock and secondarily from P₁j source rock in the sag west of Pen-1 Well. The gases are likely gas mixtures of humic and sapropelic organic origins, with the sapropelic gas type dominant in the mixture. The gas mixture is most likely cracked from kerogen rather than oils. The Carboniferous volcanic reservoirs in Shixi Bulge share some unique characteristics that may provide useful insights into the various roles of different volcanic reservoir types in old volcanic provinces. The presence of these reservoirs will undoubtedly encourage future petroleum exploration in volcanic rocks up to the deep parts of sedimentary basins.     

Diagenetic differences caused by the charging of natural gases with various compositions - a case study on the lower Zhuhai Formation clastic reservoirs in the WC-A sag,the Pearl River Mouth Basin

Only a limited number of comparative studies have explored the diagenetic differences of reservoirs caused by the charging of natural gases with different compositions during the migration and accumulation of oil and gas. In this study, we quantitatively assessed the diagenetic variations of the lower Zhuhai Formation reservoirs in the WC-A sag, the Pearl River Mouth Basin, as a result of natural gas charging with different compositions. The employed methods included electron microscopy, scanning electron microscopy, cathode luminescence, X-ray diffraction, chemical composition analysis of formation water, stable isotope analysis, and fluid inclusion determination. The results indicated that: (1) in the lower Zhuhai Formation reservoir that are near the large fractures, the late-charging of CO₂-rich thermal fluid promoted the dissolution of minerals, and changed the porosity, permeability, pH value of fluid, and the contents of ions such as K⁺, Na⁺, Mg²⁺ of the reservoirs. These changes, in turn, indirectly affected the content, form, and distribution of clay minerals in the reservoirs. In addition, the secondary enlargement of quartz was enhanced. (2) The charging of CO₂-rich thermal fluid caused strong dissolution and produced high contents of cements. The dissolution mainly occurred in a half open system with strong fluid activity. Consequently, the significantly decreasing of permeability was hindered and middle porosity–middle permeability reservoirs were generated. The reservoirs that are far from the large fractures, however, were mainly early charged by the hydrocarbon-rich fluid. The dissolution was weak and the generated cements were limited. In addition, the dissolution products could not be discharged in such closed diagenetic systems. As a result, the permeability of the reservoir was declined sharply and resulted in low porosity–low permeability reservoirs.     

Hydrothermal dolomite reservoir in the Precambrian Dengying Formation of central Sichuan Basin,Southwestern China

The Precambrian Dengying Formation is maximum buried carbonate reservoir in the Sichuan Basin. Reservoir types are thought to be dominated by sedimentary facies or karst controlled. Precursory sedimentary fabrics have been intensively superimposed by medium-to coarse-grained dolomite in most areas. Dolomitized intervals contain planar and saddle dolomite, quartz, and few hydrothermal replacive minerals. Fluid inclusion analyses of dolomite suggests that rocks are formed at temperatures ranging from 132.6°C to 218.7°C in the presence of dense brines, while the dolomite phases are demonstrated by negative δ¹⁸O and δ¹³C VPDB values. Strontium isotopes enriched in ⁸⁷Sr, and the fluid source could support the conclusion. The dolomites of the Dengying Formation in central Sichuan Basin that formed around basement-rooted wrench faults, in turn mainly oriented towards the North-South and East-West strike-slip faults, are detectable. Lastly, the grabens take the form of negative flower structures-the result of an intra-cratonic rift that took place during the Sinian and early Cambrian period through tensional faulting.Our primary contention is that basement fault, which resulted in the magmatic or deep clastic fluids migration, was key for the formation of the obvious high-temperature coarse dolomite and saddle dolomite replacement. Subsequently, hot fluids that circulated within the matrix dolomite were aided by fractures or vugs and (1) leached into the dolomite, producing vugs and pores; (2) precipitated saddle dolomite, and (3) led to hydrofracturing, fractures enlargement, and further brecciation. The dolomite eventually formed porous hydrocarbon reservoirs through diagenesis. This model better illustrates how fluids that originated from deep basin migration along strike-slip transfer faults and fractures flowed out to structures in Precambrian basement-rooted faults, inheriting the rift in the Cambrian. The data involved offers a fresh perspective pertinent to deep hydrocarbon exploration of dolomite reservoirs in Southwestern China.     

Beef veins and thrust detachments in Early Cretaceous source rocks,foothills of Magallanes-Austral Basin,southern Chile and Argentina: Structural evidence for fluid overpressure during hydrocarbon maturation

We describe (1) bedding-parallel veins of fibrous calcite (beef) and (2) thrust detachments, which we believe provide good evidence for fluid overpressure in source rocks for petroleum. Our examples are from the surface or subsurface of the Magallanes-Austral Basin, which lies at the southern tip of South America. There, the best source rocks for petroleum are of Early Cretaceous age. In the central parts of the basin these source rocks have become overmature, but at the eastern edge, onshore and offshore, they are today either immature or in the oil window.In Tierra del Fuego, the foothills of the Andes consist mainly of sedimentary rocks, which have undergone thin-skinned thrusting. In the Vicuña area (Chile), Early Cretaceous source rocks have reached the surface above thrust detachments, which are visible on seismic data and well data. At the surface, we have found calcite beef, containing hydrocarbons (solid and/or fluid), in the Rio Jackson and Vicuña formations, which have reached the wet gas window. In the Rio Gallegos area (Argentina), the source rocks have not reached the surface, but seismic and well data provide good evidence for thin-skinned thrusting above flat-lying detachments in Early Cretaceous source rock, where it is in the early oil window. In contrast, there is little or no deformation where the source rock is still immature. Thus the deformation front coincides with the maturity front. Next to the central parts of the basin, where the source rocks have reached the surface within the Andes proper, they have undergone low-grade metamorphism. Within these source rocks, we have found beef veins, but of quartz, not calcite. To the east, within the foreland basin, seismic and well data provide evidence for a few compressional structures, including thin-skinned detachments in the deeply buried source rock. Finally, in the northern part of the basin (Santa Cruz province, Argentina), where it is shallower, the source rocks have reached the surface in the foothills, above a series of back-thrusts. At Lago San Martín, the source rocks have reached the oil window and they again contain calcite beef.In conclusion, where we have examined Early Cretaceous source rocks at the surface, they contain either calcite beef (if they have reached the late oil window or wet gas window) or quartz beef (if they are overmature). Independent evidence for overpressure, in the form of source-rock detachments, comes from subsurface data, especially at the southern end of the basin, where the source rocks are not overmature and deformation is relatively intense. Thus we argue that hydrocarbon generation has led to overpressure, as a result of chemical compaction and load transfer, or volume changes, or both.     

Fracturing and calcite cementation controlling fluid flow in the shallow-water carbonates of the Jandaíra Formation,Brazil

The shallow-marine carbonate rocks of the Jandaíra Formation have been subject to significant permeability variations through time due to various events of fracturing and calcite cementation. As a consequence, the Jandaíra Formation accommodated fluid flow only during specific moments in time. We reconstructed these episodes of fluid flow based on isotope characterizations and microscope characteristics of calcite veins and host rock cements. The Jandaíra Formation, which belongs to the post-rift sequence of the Potiguar Basin in northeast Brazil, was deposited from the Turonian onward until a marine regression exposed it in the Campanian. Due to the subaerial exposure, meteoric waters flushed out marine connate waters, leading to an event of early diagenesis and full cementation of the Jandaíra Formation. Fluid flow through the resulting impermeable carbonate formation appears to be closely related to fracturing. Fracturing in the Late Cretaceous induced a drastic increase in permeability, giving rise to extensive fluid circulation. Host rock dissolution associated to the circulating fluids led to calcite vein cementation within the fracture network, causing it to regain an impermeable and sealing character. In the research area, fluid flow occurred during early burial of the Jandaíra Formation at estimated depths of 400–900 m. This study documents the first application of fluid inclusion isotope analysis on vein precipitates, which allowed full isotopic characterization of the paleo-fluids responsible for calcite vein cementation. The fluid inclusion isotope data indicate that upwelling of groundwater from the underlying Açu sandstones provided the fluids to the fracture network. In Miocene times, renewed tectonic compression of a lower intensity created a secondary fracture network in the Jandaíra Formation. The density of this fracture network, however, was too low to induce a new episode of fluid circulation. As a result, this tectonic event is associated with the development of barren extensional fractures.     

Paleotemperatures and paleofluids recorded in fluid inclusions from calcite veins from the northern flank of the Ponta Grossa dyke swarm: Implications for hydrocarbon generation and migration in the Paraná Basin

The Paraná Basin, southern Brazil, has an atypical thermal and fluid history due to the occurrence of an episodic continental flood volcanism during the Early Cretaceous. So far, there are few data about the influence of this volcanic event on the paleotemperatures and paleofluids of the Paraná Basin sedimentary rocks. The Teresina Formation in the northern flank of the Ponta Grossa dyke swarm hosts high concentration of subsurface igneous rock bodies (sills and dykes), besides its covering by a hundreds meter thick volcanic rock cap. In this study, we used fluid inclusion analysis performed in horizontal and vertical calcite veins from the Teresina Formation and from a Late Cretaceous basic dyke to estimate paleotemperatures and to characterize the composition of diagenetic paleofluids. Homogenization temperatures of requilibrated fluid inclusions show that the Teresina Formation reached temperatures above 200 °C. Horizontal parallel bedding calcite veins from the Teresina Formation record low to high salinity (2–26 wt.% NaCl eq.) aqueous paleofluids. The prevalence of high salinity fluid inclusions associated with light hydrocarbon fluid inclusions indicates deep buried fluids. Fluid inclusions in vertical calcite vein from basic dyke comprise only low salinity aqueous fluids (0–3 wt.% eq.NaCl) interpreted as dominated by meteoric water. The recorded paleotemperatures are attributed to the heating by the Paraná volcanic event during the Early Cretaceous, with the thermal effect of the volcanic rock cap surpassing the effect of nearby sills and dykes. Estimated paleotemperatures higher than 200 °C would allow the generation of light liquid and gaseous hydrocarbons. Overpressured compartments in the Teresina Formation allowed the expulsion of buried pore fluids (high salinity aqueous fluids and hydrocarbons) to fracture systems, where they mixed with meteoric water. The input of meteoric water through fracture systems connected with the surface favored hydrocarbons degradation in the early stages of source rock maturation during the Early Cretaceous.     

Hydrocarbon migration and accumulation of the Suqiao buried-hill zone in Wen'an Slope,Jizhong Subbasin,Bohai Bay Basin,China

The hydrocarbon migration and accumulation of the Suqiao deep buried-hill zone, in the Jizhong Subbasin, the Bohai Bay Basin, eastern China, was investigated from the perspective of paleo-fluid evidence by using fluid inclusions, quantitative fluorescence techniques (QGF), total scanning fluorescence method (TSF) and organic geochemical analysis. Results show that the current condensate oil-gas reservoirs in the study area once were paleo-oil reservoirs. In addition, the reservoirs have experienced at least two stages of hydrocarbon charge from different sources and/or maturities. During the deposition of the Oligocene Dongying Formation (Ed), the deep Ordovician reservoirs were first charged by mature oils sourced from the lacustrine shale source rocks in the fourth member of Shahejie and Kongdian Formations (Es₄+Ek), and then adjusted at the end of Ed period subsequently by virtue of the tectonic movement. Since the deposition of the Neogene Minghuazhen Formation (Nm), the reservoirs were mainly charged by the gas that consisted of moderate to high-maturity condensate and wet gas sourced from the Es₄+Ek lacustrine shale source rocks and mature coal-derived gas sourced from the Carboniferous-Permian (C-P) coal-bearing source rocks. Meanwhile, the early charged oil was subjected to gas flushing and deasphalting by the late intrusion of gas. The widely distributed hydrocarbon inclusions, the higher QGF Index, and FOI (the frequency of oil inclusions) values in both gas-oil and water zone, are indicative of early oil charge. In addition, combined with the homogenization temperatures of the fluid inclusions (<160 °C) and the existence of solid-bitumen bearing inclusions, significant loss of the n-alkanes with low carbon numbers, enrichments of heavier components in crude oils, and the precipitation of asphaltene in the residual pores suggest that gas flushing may have played an important role in the reservoir formation.     

Petroleum accumulation in the deeply buried reservoirs in the northern Dongying Depression,Bohai Bay Basin,China: New insights from fluid inclusions,natural gas geochemistry,and 1-D basin modeling

The deeply buried reservoirs (DBRs) from the Lijin, Shengtuo and Minfeng areas in the northern Dongying Depression of the Bohai Bay Basin, China exhibit various petroleum types (black oil-gas condensates) and pressure systems (normal pressure-overpressure) with high reservoir temperatures (154–185 °C). The pressure-volume-temperature-composition (PVTX) evolution of petroleum and the processes of petroleum accumulation were reconstructed using integrated data from fluid inclusions, stable carbon isotope data of natural gas and one-dimensional basin modeling to trace the petroleum accumulation histories.The results suggest that (1) the gas condensates in the Lijin area originated from the thermal cracking of highly mature kerogen in deeper formations. Two episodes of gas condensate charging, which were evidenced by the trapping of non-fluorescent gas condensate inclusions, occurred between 29-25.5 Ma and 8.6–5.0 Ma with strong overpressure (pressure coefficient, P_c = 1.68–1.70), resulting in the greatest contribution to the present-day gas condensate accumulation; (2) the early yellow fluorescent oil charge was responsible for the present-day black oil accumulation in well T764, while the late blue-white oil charge together with the latest kerogen cracked gas injection resulted in the present-day volatile oil accumulation in well T765; and (3) the various fluorescent colors (yellow, blue-white and blue) and the degree of bubble filling (F_v) (2.3–72.5%) of the oil inclusions in the Minfeng area show a wide range of thermal maturity (API gravity ranges from 30 to 50°), representing the charging of black oil to gas condensates. The presence of abundant blue-white fluorescent oil inclusions with high Grain-obtaining Oil Inclusion (GOI) values (35.8%, usually >5% in oil reservoirs) indicate that a paleo-oil accumulation with an approximate API gravity of 39–40° could have occurred before 25 Ma, and gas from oil cracking in deeper formations was injected into the paleo-oil reservoir from 2.8 Ma to 0 Ma, resulting in the present-day gas condensate oil accumulation. This oil and gas accumulation model results in three oil and gas distribution zones: 1) normal oil reservoirs at relatively shallow depth; 2) gas condensate reservoirs that originated from the mixture of oil cracking gas with a paleo-oil reservoir at intermediate depth; and 3) oil-cracked gas reservoirs at deeper depth.The retardation of organic matter maturation and oil cracking by high overpressure could have played an important role in the distribution of different origins of gas condensate accumulations in the Lijin and Minfeng areas. The application of oil and gas accumulation models in this study is not limited to the Dongying Depression and can be applied to other overpressured rift basins.     

Properties and shale oil potential of saline lacustrine shales in the Qianjiang Depression,Jianghan Basin,China

The geochemical and petrographic characteristics of saline lacustrine shales from the Qianjiang Formation, Jianghan Basin were investigated by organic geochemical analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM) and low pressure nitrogen adsorption analysis. The results indicate that: the saline lacustrine shales of Eq3 member with high oil content are characterized by type I and type II oil-prone kerogen, variable TOC contents (1.0–10.0 wt%) and an early-maturity stage (R_o ranges between 0.41 and 0.76%). The mineral compositions of Eq3 saline shale show strong heterogeneity: brittle intervals with high contents of quartz and carbonate are frequently alternated with ductile intervals with high glauberite and clay contents. This combination might be beneficial for oil accumulation, but may cause significant challenges for the hydraulic stimulation strategy and long-term production of shale oil. The interparticle pores and intraparticle pores dominate the pore system of Eq3 shale, and organic matter hosted pores are absent. Widely distributed fractures, especially tectonic fractures, might play a key role in hydrocarbon migration and accumulation. The pore network is contributed to by both large size inorganic pores and abundant micro-factures, leading to a relatively high porosity (2.8–30.6%) and permeability (0.045–6.27 md) within the saline shale reservoir, which could enhance the flow ability and storage capacity of oil. The oil content (S₁ × 100/TOC, mg HC/g TOC and S₁, mg HC/g rock) and brittleness data demonstrate that the Eq3^3x section has both great potential for being a producible oil resource and hydraulic fracturing. Considering the hydrocarbon generation efficiency and properties of oil, the mature shale of Eq3 in the subsidence center of the Qianjiang Depression would be the most favorable zone for shale oil exploitation.     

Mineral carbon MinC(%) from Rock-Eval analysis as a reliable and cost-effective measurement of carbonate contents in shale source and reservoir rocks

The abundance of carbonate minerals in rocks is an important element for petroleum geochemists, geologists and engineers to consider during hydrocarbon exploration and production. Carbonate minerals can be related to the depositional environments of the source rocks and hence the type of organic matter that can be subsequently modified through diagenetic processes. The total carbonate content in shales can also be used to deduce their fracability as reservoir rock for shale gas/oil extraction. At present, mineralogical analysis by X-ray diffraction (XRD) is the most widely used technique in the oil and gas-related petrophysical and geochemical laboratories for identifying and quantifying carbonate minerals in rock samples. In contrast, the use of the total mineral carbon content parameter MinC (%) from Rock-Eval analysis has been limited despite (1) the parameter's effectiveness as demonstrated through instrument and methodology development; and (2) the presence of a large volume of Rock-Eval results due to its widespread use in the oil and gas industry.In this study, we acquired XRD and Rock-Eval analytical results on over nine hundred rock samples ranging from Ordovician to Cretaceous age from four petroleum sedimentary basins in Canada. Least-squares regression analyses produce empirical equations with R² values greater than 0.92 for the correlations between XRD total carbonate contents and the Rock-Eval MinC (%) values of six different suites of samples. This indicates that the MinC (%) values generated by Rock-Eval 6 and other instruments of similar capability can be used with confidence for estimating the amounts of total carbonates in sedimentary rock samples. While the correlation between the two types of carbonate content measurements is geology-specific, a global linear regression model (R² of 0.97) based on the large combined data set has been proposed for approximating the total carbonate abundances based on Rock-Eval MinC (%) values.