Numerical analysis of the interaction of soil-structure under earthquake loading

Ｎｕｍｅｒｉｃａｌａｎａｌｙｓｉｓｏｆｔｈｅｉｎｔｅｒａｃｔｉｏｎｏｆｓｏｉｌ┐ｓｔｒｕｃｔｕｒｅｕｎｄｅｒｅａｒｔｈｑｕａｋｅｌｏａｄｉｎｇＧＥＮ－ＤＥＺＨＡＮＧ１）（章根德）ＳＨＵ－ＣＨＥＮＧＮＩＮＧ２）（宁书成）１）ＩｎｓｔｉｔｕｔｅｏｆＭｅ...     

新疆巴楚地震液化宏观现象的对比分析

2003年2月24日新疆巴楚-伽师地区发生6.8级地震,出现了唐山、海城地震后近30年我国最具规模的砂土液化现象。本文通过现场调查和资料分析,并与以往大地震液化比较,提出了此次地震液化宏观现象的认识,包括液化分布特征、喷水冒砂形态、液化震害和工程地质条件等几个方面。结果表明,此次地震液化宏观现象与我国以往几次大地震有很多不同,具有很大的研究价值。     

Shear wave velocity-based liquefaction evaluation in the great Wenchuan earthquake： a preliminary case study

The great Wenchuan earthquake (Ms = 8.0) in 2008 caused severe damage in the western part of the Chengdu Plain. Soil liquefaction was one of the major causes of damage in the plain areas, and proper evaluation of liquefaction potential is important in the definition of the seismic hazard facing a given region and post-earthquake reconstruction. In this paper, a simplified procedure is proposed for liquefaction assessment of sandy deposits using shear wave velocity (Vs), and soil liquefaction from the Banqiao School site was preliminarily investigated after the earthquake. Boreholes were made at the site and shear wave velocities were measured both by SASW and down-hole methods. Based on the in-situ soil information and Vs profiles, the liquefaction potential of this site was evaluated. The results are reasonably consistent with the actual field behavior observed after the earthquake, indicating that the proposed procedure is effective. The possible effects of gravel and fines contents on liquefaction of sandy soils were also briefly discussed.     

某长江大桥深度超过15米的砂土层液化势的综合评价

不同抗震设计规范的砂土液化判别方法或国内外其他有代表性的液化判别方法所采用的地震动参数和土性指标及其埋藏条件是不同的,因而采用这些方法对同一工程场地进行液化势预测时其评价结果通常有一些差异,甚至会得到相反的结论。为了给重大工程建设提供较为合理、可信的地基液化势预测结果,采用多种液化判别方法进行场地液化势的综合评价是比较客观的,也是必要的。本文结合某长江大桥桥基工程,采用建筑抗震设计规范的砂土液化判别方法、国内外有代表性的液化判别方法、有限元数值分析法等多种方法逐一对该工程场地砂性土层进行液化判别,并结合室内动三轴液化试验结果,对主桥墩不考虑冲刷条件和考虑一般冲刷深度5m条件时的砂性土层进行了液化势的综合评价,并将各土层的液化势分为液化、可能液化和不液化3个等级,得到了较为合理可靠的判别结果。     

关于砂土液化判别的若干意见

简要回顾了我国抗震规范中液化判别方法的发展历史,并对我国若干规范中的液化初步判别的条文进行了比较,提出了修改意见;对我国有代表性的几种液化判别方法及基于Seed简化方法修正的美国NCEER法进行了评述和综合对比,指出了我国现行若干规范中有关液化判别规定方面的错误;此外,还将GB50011－2001《建筑抗震设计规范》液化判别公式转变为类似于NCEER法的表达式,拓宽了该规范方法的应用范围。最后,结合某长江大桥工程的地基液化判别工作,探讨了深层土液化判别的可能性,结果表明,本文建议的方法是可行的。     

动载作用下饱和土壤液化的研究述评

从土壤液化的机理、影响因素、液化的判别、液化的分析方法以及液化后土壤的性质等方面详述了动载(地震荷载和爆炸荷载)作用下的饱和土壤液化的国内外研究成果(主要是近十年的研究),并对其作出了述评。最后,对今后土壤液化的研究工作作出了展望,认为以下问题需要开展深入研究:⑴液化分析中的土骨架的动力本构模型;⑵Rayle igh波对地震液化的影响;⑶建构物的存在对液化的影响;⑷液化后土的性质和液化引起的建构物破坏;⑸尤其爆炸液化问题。     

黄土液化机理和判别标准的再研究

本文结合作者的试验研究和国外最新研究进展对黄土液化问题作了一些深入讨论。在一定的条件下,黄土可能发生液化,而且相当一部分黄土符合“修正的中国标准”。从液化机理上讲,黄土液化属于流滑。试验研究发现,黄土液化过程与应变发展有内在的联系,因而在动三轴试验中用轴向应变作为黄土初始液化的判别条件更符合实际。最后,通过对俄罗斯、美国和中国黄土的对比研究,作者认为黄土的粒度组成对黄土的液化特性有明显的影响。     

地震作用下穿越管道砂土液化实验研究

本文研究了引滦入港工程水下穿越管道土质情况，对土层的主要物理、力学性质进行实验分析并设计了实验室装置，进行5种工况实验分析，得出了有益的结论。     

Reduction of earthquake disasters

The article summarizes the researches on mitigating earthquake disasters of the past four years in China. The studyof earthquake disasters′ quantification shows that the losses increase remarkably when population concentrates inurban area and social wealth increase. The article also summarizes some new trends of studying earthquake disas-ters′ mitigation, which are from seismic hazard to seismic risk, from engineering disaster to social disaster andintroduces the community-centered approach.     

Adaptive element free Galerkin method applied to analysis of earthquake induced liquefaction

An automatically adaptive element free method is presented to analyze the seismic response of liquefiable soils.The method is based on the element free Galerkin method (EFGM) and the fission procedure that is part of h-refinement,indicated by error estimation. In the proposed method, a posteriori error estimate procedure that depends on the energy normof stress and the T-Belytschko (TB) stress recovery scheme is incorporated. The effective cyclic elasto-plastic constitutivemodel is used to describe the nonlinear behavior of the saturated soil. The governing equations are established by u-pformulation. The proposed method can effectively avoid the volumetric locking due to large deformation that usually occursin numerical computations using the finite element method (FEM). The efficiency of the proposed method is demonstratedby evaluating the seismic response of an embankment and comparing it to results obtained through FEM. It is shown that theproposed method provides an accurate seismic analysis of saturated soil that includes the effects of liquefaction     

液化场地桩-土-桥梁结构动力相互作用振动台试验研究进展

本文在全面归纳与总结液化场地桩－土－桥梁结构动力相互作用振动台试验及与之相关领域的国内外研究进展基础上，直接针对我国桥梁工程中的主要震害问题，提出在我国开展液化场地桩－土－桥梁结构动力相互作用振动台试验研究的必要性，并阐述作者对液化场地桩－土－张桥梁结构动力相互作用振动台试验中若干问题的认识。     

Three-dimensional liquefaction potential analysis using geostatistical interpolation

We applied three-dimensional geostatistical interpolation to evaluate the extent of liquefiable materials at two sites that liquefied during the 1994 Northridge Earthquake. The sites were the Balboa Blvd site and the Wynne Ave. site located in the alluvial San Fernando Valley. The estimated peak ground accelerations at the sites are 0.84 g (Balboa Blvd) and 0.51 g (Wynne Ave.). These sites were chosen because surface effects due to liquefaction were not predicted using available techniques based on thickness and depth of liquefiable layers (Ishihara [Ishihara K. Stability of natural deposits during earthquakes. Proceedings of the 11th international conference on soil mechanics and foundation engineering, vol. 1. Rotterdam, The Netherlands: A.A. Balkema; 1985. p. 321–76.]) and the Liquefaction Potential Index (Iwasaki et al. [Iwasaki T, Tatsuoka F, Tokida K, Yasuda S. A practical method for assessing soil liquefaction potential based on case studies at various sites in Japan. In: Proceedings of the second international conference on microzonation, San Francisco; 1978. p. 885–96.]). During the earthquake, both sites experienced surface effects including ground cracking and extension as a result of liquefaction. Foundations and buried utilities were damaged at both sites. The sites were investigated after the event by researchers with the United States Geologic Survey using standard penetration tests (SPT) and cone penetration tests. In this paper, liquefaction potential was estimated for each soil sample using results from SPTs according to the updated Seed and Idriss simplified procedure. The probability of liquefaction was estimated by applying an indicator transform to the results of the liquefaction potential calculation. We compared our results to detailed geologic mapping of the sites performed by other researchers. Using geostatistical interpolation to estimate the probability of liquefaction is a useful supplement to geologic evaluation of liquefaction potential. The geostatistical analysis provides an estimate of the continuous volume of liquefiable soil along with an assessment of confidence in an interpolation. The probability of liquefaction volumes compare well with those predicted using geologic interpretations.     

A semi-empirical formula for evaluating residual strain of soils under earthquake loading

A new semi-empirical formula for evaluating the residual strain of soils under earthquake loading is presented in this paper based on the incremental method and the increment model proposed by the authors. When the incident loading is uniform, the results calculated by the new formula are nearly the same as those by the existing formula. For excitation of the random earthquake loading, the results calculated by the new formula are compared to the results obtained by dynamic triaxial tests. The dynamic triaxial tests had been performed considering different seismic waves, confining stresses,consolidation ratios, and types of cohesive soils. The comparison between the calculated and tested results indicate that the presented formula can efficiently and practically describe the time-dependent process of the soil residual strains under actual seismic loads.     

可液化地基土三维地震响应分析

编制完全耦合的三维排水有效应力动力反应分析程序，对可液化地基进行三维地震响应分析，探讨了不同土性参数、不同土层构成和不同附加压重等因素对可液化地基抗液化性能的影响。结果表明：在地震荷载作用下，天然饱和砂土地基中的超孔隙水压力随深度的增大而增大；在不同深度处，超孔压峰值到达的时刻比地震加速度峰值到达的时刻要晚；随输入地震加速度的减弱，深层处的超孔压开始消散或基本保持不变，浅层处的超孔压保持不变或略有上升，这一现象与土性参数、输入地震荷载的情况等因素有关；土性参数对土体本身的抗液化性能有重要影响，初始孔隙比越小，相对密度越大，土体的抗液化能力越强；附加压重有利于地基抗液化能力的提高；随着附加压重的增大，超孔压比减小；附加压重对地基中超孔隙水压力的增长有明显的抑制作用。     

Evaluation of the seismic hazard of Lebanon

This paper presents the results of a study undertaken todetermine the seismic hazard of Lebanon. The seismic hazard evaluation wasconducted using probabilistic methods of hazard analysis. Potential sourcesof seismic activities that affect Lebanon were identified and the earthquakerecurrence relationships of these sources were developed from instrumentalseismology data, historical records, and earlier studies undertaken toevaluate the seismic hazard of neighboring countries. The sensitivityof the results to different assumptions regarding the seismic sources in theLebanese segment and choice of the attenuation relationship wasevaluated. Maps of peak ground acceleration contours, based on 10percent of probability of exceedance in 50 years and 100 years time spans,were developed.     

Ground motion evaluation procedures for performance-based design

The objective of performance-based earthquake engineering (PBEE) is the analysis of performance objectives with a specified annual probability of exceedance. Increasingly undesirable performance is caused by increasing levels of strong ground motion having decreasing annual probabilities of exceedance. Accordingly, the evaluation of ground motion intensity measures is a vital component of PBEE. This paper provides a brief synthesis of ground motion analysis procedures within a performance-based design framework, and is a summary of a recent report to which the reader is referred for details. The principal topics addressed are probabilistic characterizations of source, path, and site effects, with the discussion of these effects focusing principally on applications in active regions such as California.     

Assessment of soil liquefaction incorporating earthquake characteristics

This paper investigates the effect of nature of the earthquake on the assessment of liquefaction potential of a soil deposit during earthquake loading. Here, the nature of the earthquake is included via the parameter V, the ‘pseudo-velocity’, that is the gross area under the acceleration record of the earthquake at any depth below the ground surface. By analysing a number of earthquake records from different parts of the world, a simple method has been outlined to assess the liquefaction potential of a soil deposit based on the pseudo-velocity. For many earthquakes occurred in the past, acceleration records are available or can be computed at the ground level or some other depth below the ground surface. Therefore, this method is a useful tool at the preliminary design stage to determine the liquefaction potential before going into a detailed analysis. Validation of the method is carried out using a database of case histories consisting of standard penetration test values, acceleration records at the ground surface and field observations of liquefaction/non-liquefaction. It can be seen that the proposed method has the ability to predict soil liquefaction potential accurately, despite its simplicity.     

Parallel finite element modeling of earthquake ground response and liquefaction

Parallel computing is a promising approach to alleviate the computational demand in conducting large-scale finite element analyses. This paper presents a numerical modeling approach for earthquake ground response and liquefaction using the parallel nonlinear finite element program, ParCYCLIC, designed for distributed-memory message-passing parallel computer systems. In ParCYCL1C, finite elements are employed within an incremental plasticity, coupled solid-fluid formulation. A constitutive model calibrated by physical tests represents the salient characteristics of sand liquefaction and associated accumulation of shear deformations. Key elements of the computational strategy employed in ParCYCL1C include the development of a parallel sparse direct solver, the deployment of an automatic domain decomposer, and the use of the Multilevel Nested Dissection algorithm for ordering of the finite element nodes. Simulation results of centrifuge test models using ParCYCLIC are presented. Performance results from grid models and geotechnical simulations show that ParCYCLIC is efficiently scalable to a large number of processors.     

Stress-strain transformations and liquefaction of sands

Presented in this paper are the results of the laboratory tests of sands performed for the purpose of defining the characteristics of the dynamic shear stress-shear strain relationships. For this purpose, the transformation of the initial stress-strain characteristics of undrained saturated sands was investigated separately. These transformations take place under conditions of an increase in pore pressure under the effect of sufficiently intensive dynamic excitations. The process of occurrence and development of liquefaction was investigated simultaneously. The obtained results show that the transformation of the stress-strain relationships leads to intensive reduction in the initial dynamic characteristics of sands. At the moment of occurrence of initial liquefaction, for the selected strain, shear moduli are considerably reduced in respect to their initial values. These parameters tend to be further reduced in the phase of post-initial liquefaction. It is concluded that the process of liquefaction of sands can be completely defined through the transformation of the stress-strain relationships.