Jet flow over foredunes

Jet flows, which are localized flows exhibiting a high speed maxima, are relatively common in nature, and in many devices. They have only been occasionally observed on dunes, and their dynamics are poorly known. This paper examines computational fluid dynamic (CFD) two‐dimensional (2D) modelling of jet flow over a foredune topography. Flow was simulated in 10° increments from onshore (0°) to highly oblique alongshore (70°) incident wind approach angles. CFD modelling reveals that the formation of a jet is not dependent on a critical wind speed, and an increase in incident wind velocity does not affect the magnitude of jet flow. A jet is first formed at ~1.0 m seawards of the foredune crest on the Prince Edward Island foredune morphology example examined here. A jet is not developed when the incident wind is from an oblique approach angle greater than ~50° because there is significantly less flow acceleration across a much lower slope at this incident angle. The presence of a scarp does influence the structure of the crest jet, in that the jet is more pronounced where a scarp is present. Surface roughness affects the magnitude of jet expansion and jets are better developed on bare surfaces compared to vegetated ones. Copyright © 2016 John Wiley & Sons, Ltd.     

Aeolian dynamics over a coastal foredune,Prince Edward Island,Canada

Near‐surface airflow over a morphologically simple, vegetated, 8 m high foredune with a small wave‐cut scarp was measured for onshore to oblique‐onshore conditions during a low‐moderate (5–6 m s^‐1 ) wind event and a high velocity (11–18 m s^‐1) sand‐transporting gale event. Flow across the foredune was characterized by significant flow compression and acceleration up and across the foredune during both events. During the gale, a pronounced jet (speed bulge) developed at the foredune crest, which increased in magnitude with increasing wind speed. The vertical (W) velocity component of the 3D flow field was positive (upwards) across the stoss slope under low wind conditions but negative (downwards) during gale wind conditions, with upslope acceleration. During the low velocity event, there was speed‐down within the vegetation canopy, as would be expected for a porous roughness cover. During the strong wind event there was speed‐up in the lower portion of the vegetation canopy, and this was found up the entire stoss slope. Sediment transport during the gale force event was substantial across the beach and foredune despite the moderate vegetation cover and minimum fetch. Aeolian suspension was evident in the lee of the dune crest. The observations presented herein show that strong storm winds are an effective mechanism for translating sediment landwards across a high vegetated foredune, contributing sediment to the stoss slope, crest and leeward slopes of the foredune and backing dunes. Copyright © 2013 John Wiley & Sons, Ltd.     

High‐frequency sediment transport responses on a vegetated foredune

Wind flow and sand transport intensity were measured on the seaward slope of a vegetated foredune during a 16 h storm using an array of sonic anemometers and Wenglor laser particle counters. The foredune had a compound seaward slope with a wave‐cut scarp about 0.5 m high separating the upper vegetated portion from the lower dune ramp, which was bare of vegetation. Wind direction veered from obliquely offshore at the start of the event to obliquely onshore during the storm peak and finally to directly onshore during the final 2 h as wind speed dropped to below threshold. Sand transport was initially inhibited by a brief period of rain at the start of the event but as the surface dried and wind speed increased sand transport was initiated over the entire seaward slope. Transport intensity was quite variable both temporally and spatially on the upper slope as a result of fluctuating wind speed and direction, but overall magnitudes were similar over the whole length. Ten‐minute average transport intensity correlates strongly with mean wind speed measured at the dune crest, and there is also strong correlation between instantaneous wind speed and transport intensity measured at the same locations when the data are smoothed with a 10 s running mean. Transport on the beach for onshore winds is decoupled from that on the seaward slope above the small scarp when the wind angle is highly oblique, but for wind angles <45° from shore perpendicular some sand is transported onto the lower slope. Copyright © 2012 John Wiley & Sons, Ltd.     

Aeolian sediment transport on a human‐altered foredune

Changes in wind speed and sediment transport are evaluated at a gap and adjacent crest of a 2 to 3 m high, 40 m wide foredune built by sand fences and vegetation plantings on a wide, nourished fine sand beach at Ocean City, New Jersey. Anemometer masts, cylindrical sand traps and erosion pins were placed on the beach and dune during two obliquely onshore wind events in February and March 2003. Results reveal that: (1) changes in the alongshore continuity of the beach and dune system can act as boundaries to aeolian transport when winds blow at an angle to the shoreline; (2) oblique winds blowing across poorly vegetated patches in the dune increase the potential for creating an irregular crest elevation; (3) transport rates and deflation rates can be greater within the foredune than on the beach, if the dune surface is poorly vegetated and the beach has not had time to dry following tidal inundation; (4) frozen ground does not prevent surface deflation; and (5) remnant sand fences and fresh storm wrack have great local but temporary effect on transport rates. Temporal and spatial differences due to sand fences and wrack, changes in sediment availability due to time‐dependent differences in surface moisture and frozen ground, combined with complex topography and patchy vegetation make it difficult to specify cause–effect relationships. Effects of individual roughness elements on the beach and dune on wind flow and sediment transport can be quantified at specific locations at the event scale, but extrapolation of each event to longer temporal and spatial scales remains qualitative. Copyright © 2006 John Wiley & Sons, Ltd.     

Wind direction and complex sediment transport response across a beach–dune system

Evidence from a field study on wind flow and sediment transport across a beach–dune system under onshore and offshore conditions (including oblique approach angles) indicates that sediment transport response on the back‐beach and stoss slope of the foredune can be exceedingly complex. The upper‐air flow – measured by a sonic anemometer at the top of a 3·5 m tower located on the dune crest – is similar to regional wind records obtained from a nearby meteorological station, but quite different from the near‐surface flow field measured locally across the beach–dune profile by sonic anemometers positioned 20 cm above the sand surface. Flow–form interaction at macro and micro scales leads to strong modulation of the near‐surface wind vectors, including wind speed reductions (due to surface roughness drag and adverse pressure effects induced by the dune) and wind speed increases (due to flow compression toward the top of the dune) as well as pronounced topographic steering during oblique wind approach angles. A conceptual model is proposed, building on the ideas of Sweet and Kocurek (Sedimentology 37 : 1023–1038, 1990), Walker and Nickling (Earth Surface Processes and Landforms 28 : 111–1124, 2002), and Lynch et al. (Earth Surface Processes and Landforms 33 : 991–1005, 2008, Geomorphology 105 : 139–146, 2010), which shows how near‐surface wind vectors are altered for four regional wind conditions: (a) onshore, detached; (b) onshore‐oblique, attached and deflected; (c) offshore, detached; and (d) offshore‐oblique, attached and deflected. High‐frequency measurements of sediment transport intensity during these different events demonstrate that predictions of sediment flux using standard equations driven by regional wind statistics would by unreliable and misleading. It is recommended that field studies routinely implement experimental designs that treat the near‐surface wind field as comprising true vector quantities (with speed and direction) in order that a more robust linkage between the regional (upper air) wind field and the sediment transport response across the beach–dune profile be established. Copyright © 2012 John Wiley & Sons, Ltd.     

A field study of mean and turbulent flow characteristics upwind,over and downwind of barchan dunes

Field‐measured patterns of mean velocity and turbulent airflow are reported for isolated barchan dunes. Turbulence was sampled using a high frequency sonic anemometer, deriving near‐surface Reynolds shear and normal stresses. Measurements upwind of and over a crest‐brink separated barchan indicated that shear stress was sustained despite a velocity reduction at the dune toe. The mapped streamline angles and enhanced turbulent intensities suggest the effects of positive streamline curvature are responsible for this maintenance of shear stress. This field evidence supports an existing model for dune morphodynamics based on wind tunnel turbulence measurements. Downwind, the effect of different dune profiles on flow re‐attachment and recovery was apparent. With transverse incident flow, a re‐attachment length between 2·3 and 5·0h (h is dune brink height) existed for a crest‐brink separated dune and 6·5 to 8·6h for a crest‐brink coincident dune. The lee side shear layer produced elevated turbulent stresses immediately downwind of both dunes, and a decrease in turbulence with distance characterized flow recovery. Recovery of mean velocity for the crest‐brink separated dune occurred over a distance 6·5h shorter than the crest‐brink coincident form. As the application of sonic anemometers in aeolian geomorphology is relatively new, there is debate concerning the suitability of processing their data in relation to dune surface and streamline angle. This paper demonstrates the effect on Reynolds stresses of mathematically correcting data to the local streamline over varying dune slope. Where the streamline angle was closely related to the surface (windward slope), time‐averaged shear stress agreed best with previous wind tunnel findings when data were rotated along streamlines. In the close lee, however, the angle of downwardly projected (separated) flow was not aligned with the flat ground surface. Here, shear stress appeared to be underestimated by streamline correction, and corrected shear stress values were less than half of those uncorrected. Copyright © 2011 John Wiley & Sons, Ltd.     

Influence of topography on wind speed over a coastal dune and blowout system at Jockey's Ridge,NC, USA

This study examines the spatial distribution of wind speed across a coastal dune system located at Jockey's Ridge State Park, North Carolina. The study area consists of a trough blowout through a foredune ridge, and the landforms that have developed behind the foredune. Wind speed and direction were measured simultaneously with single sensors placed at a fixed height in 13 locations across the blowout/dune complex. Fractional wind speed‐up is computed for sampling stations using data from a mast located on the beach as the reference. Results show that wind speeds were generally accelerated across the study site. The highest speeds were recorded on the foredune ridges adjacent to the blowout. Wind was accelerated through the center of the blowout throat and along the downwind lateral wall. Further into the blowout, at the base of the ramp to the depositional lobe, higher wind speeds shifted to the upwind lateral wall and continued to accelerate up the ramp as air exited to the rear. Significant variations in the wind speed‐up pattern were associated with different wind approach angles, with greater speed‐up occurring when the winds were aligned normal to the dune system. The speed‐up decreased as the angle of approach became increasingly oblique to the ridge. The patterns of wind speed‐up across the site point to the influence of topography on airflow. To quantify the relationship, measures of several topographic variables were obtained along sample transects running upwind from each sample station along flow lines representing different wind approach angles. Examination of correlation coefficients between wind speed‐up and topographic variables suggests that for groups of stations with similar topographic characteristics, 30–50% of the variations in speed‐up may be explained by the upwind topographic variability. Copyright © 2014 John Wiley & Sons, Ltd.     

Air flow over foredunes and implications for sand transport

More than 4000 hourly wind profiles measured on three topographically different foredunes are analysed and discussed. Wind flow over the foredunes is studied by means of the relative wind speed: the ratio between wind speed at a certain location and the reference wind speed at the same height. Relative wind speeds appear to be independent of general wind speed but dependent on wind direction. For perpendicular onshore winds the flow over the foredune is accelerated due to topographic changes and decelerated due to changes in surface roughness. Accelerations dominate over decelerations on the seaward slope. The pattern of acceleration and deceleration in relation to wind direction is more or less comparable for different foredunes, but the magnitudes differ. An increase in foredune height from 6 to 10m leads to an increase in speed-up near the top of the seaward slope from 110 to 150 per cent during onshore wind, but further increase of foredune height from 10 to 23m appears to have little effect, due to increased roughness and deflection of flow. Topography also influences the direction of the flow. Between beach and top, the flow deflects in the direction of the normal during onshore winds. During offshore winds the flow is deflected to the parallel. Near the dunefoot, deflection is always in the direction of the parallel, and increases with steeper topography. The maximum deflection near the dunefoot was 90°, over a 23 m high dune, observed during offshore winds. Patterns of erosion and sedimentation resulting from winds from different directions can be explained by the observed accelerations and decelerations. Owing to speed-up on the seaward front of the foredune, sand transport capacity of the wind increases, which results in erosion if vegetation is absent. During strong onshore wind, sand is lifted near the dunefoot and moves over the foredune in suspension. During weaker winds, vertical wind velocities do not exceed fall velocities of the sand grains, and most of the sand is deposited near the dunefoot.     

Aeolian processes across transverse dunes. I: Modelling the air flow

This paper discusses a two-dimensional second-order closure model simulating air flow and turbulence across transverse dunes. Input parameters are upwind wind speed, topography of the dune ridge and surface roughness distribution over the ridge. The most important output is the distribution of the friction velocity over the surface. This model is dynamically linked to a model that calculates sand transport rates and the resulting changes in elevation. The sand transport model is discussed in a separate paper. The simulated wind speeds resemble patterns observed during field experiments. Despite the increased wind speed over the crest, the friction velocity at the crest of a bare dune is reduced compared to the upstream value, because of the effect of stream line curvature on turbulence. These curvature effects explain why desert dunes can grow in height. In order to obtain realistic predictions of friction velocity it was essential to include equations for the turbulent variables in the model. In these equations streamline curvature is an important parameter. The main flaw of the model is that it cannot deal with flow separation and the resulting recirculation vortex. As a result, the increase of the wind speed and friction velocity after a steep dune or a slipface will be too close to the dune foot. In the sand transport model this was overcome by defining a separation zone. Copyright © 1999 John Wiley & Sons, Ltd.     

Secondary flow deflection in the lee of transverse dunes with implications for dune morphodynamics and migration

Measurements of lee‐side airflow response from an extensive array of meteorological instruments combined with smoke and flow streamer visualization is used to examine the development and morphodynamic significance of the lee‐side separation vortex over closely spaced transverse dune ridges. A differential deflection mechanism is presented that explains the three‐dimensional pattern of lee‐side airflow structure for a variety of incident flow angles. These flow patterns produce reversed, along‐dune, and deflected surface flow vectors in the lee that are inferred to result in net ‘lateral diversion’ of sand transport over one dune wavelength for incident angles as small as 10° from crest‐transverse (i.e. 80° from the crest line). This lateral displacement increases markedly with incident flow angle when expressed as the absolute value of the total deflection in degrees. Reversed and multi‐directional flow occurs for incident angles between 90° and 50°. These results document the three‐dimensional nature of flow and sand transport over transverse dunes and provide empirical evidence for an oblique migration model. Copyright © 2013 John Wiley & Sons, Ltd.     

Airflow and aeolian sediment transport patterns within a coastal trough blowout during lateral wind conditions

Blowouts are depressions that occur on coastal dunes, deserts and grasslands. The absence of vegetation in blowouts permits high speed winds to entrain and remove sediment. Whereas much research has examined patterns of wind flow and sediment transport on the stoss slopes and lee of sand dunes, no study has yet investigated the connections between secondary air‐flow structures and sediment transport in a blowout where zones of streamline compression, expansion and steering are less clearly delineated. In this study we investigated the variability of sediment flux and its relation to near‐surface wind speed and turbulence within a trough blowout during wind flow that was oblique to the axis of the blowout. Wind flow was measured using six, three‐dimensional (3D) ultrasonic anemometers while sediment flux by eight sand traps, all operating at 25 Hz. Results demonstrated that sediment flux rates were highly variable throughout the blowout deflation basin, even over short distances (< 0.5 m). Where flow was steadiest, flux was greatest. Consequently the highest rates of sediment transport were recorded on the erosional wall crest where flow was compressed and accelerated. The strength of correlation between sediment flux and wind parameter improved with an increase in averaging interval, from 10 seconds to 1 minute. At an interval of 10 seconds, however, wind speed correlated best with flux at seven of eight traps, whereas at an interval of one minute Turbulent Kinetic Energy (TKE) provided the best correlation with flux at six of the eight traps. Correlation between sediment flux and wind parameters was best in the centre of the blowout and poorest on the erosional wall crest. The evidence from this paper suggests, for the first time, that TKE may be a better predictor of sediment transport at minute scale averaging intervals, particularly over landforms where wind flow is highly turbulent. Copyright © 2014 John Wiley & Sons, Ltd.     

Aeolian transport rates across raked and unraked beaches on a developed coast

Wind characteristics and aeolian transport were measured on a naturally evolving beach and dune and a nearby site where the beach is raked and sand‐trapping fences are deployed. The beaches were composed of moderately well sorted to very well sorted fine to medium sand. The backshore at the raked site was wider and the foredune was more densely vegetated and about 1 m higher than at the unraked site. Wind speeds were monitored using anemometers placed at 1 m elevation and sand transport was monitored using vertical traps during oblique onshore, alongshore and offshore winds occurring in March and April 2009. Inundation of the low backshore through isolated swash channels prevented formation of a continuously decreasing cross‐shore moisture gradient. The surface of the berm crest was dryer than the backshore, making the berm crest the greatest source of offshore losses during offshore winds. The lack of storm wrack on the raked beach reduced the potential for sediment accumulation seaward of the dune crest during onshore winds, and the higher dune crest reduced wind speeds and sediment transport from the dune to the backshore during offshore winds. Accretion at wrack seaward of the dune toe on the unraked beach resulted in a wider dune field and higher, narrower backshore. Although fresh wrack is an effective local trap for aeolian transport, wrack that becomes buried appears to have little effect as a barrier and can supply dry sand for subsequent transport. Aeolian transport rates were greater on the narrower but dryer backshore of the unraked site. Vegetation growth may be necessary to trap sand within zones of buried wrack in order to allow new incipient foredunes to evolve. Copyright © 2010 John Wiley & Sons, Ltd.     

Experimental investigation of the velocity of a sand cloud blowing over a sandy surface

The velocity of a wind‐blown sand cloud is important for studying its kinetic energy, related erosion, and control measures. PDA (particle dynamics analyser) measurement technology is used in a wind tunnel to study the probability distribution of particle velocity, variations with height of the mean velocity and particle turbulence in a sand cloud blowing over a sandy surface. The results suggest that the probability distribution of the particle velocity in a blowing sand cloud is stochastic. The probability distribution of the downwind velocity complies with a Gaussian function, while that of the vertical velocity is greatly complicated by grain impact with the bed and particle–particle collisions in the air. The probability distribution of the vertical velocity of ?ne particles (0·1–0·3 mm sands) can be expressed as a Lorentzian function while that of coarse particles (0·3–0·6 mm sands) cannot be expressed by a simple distribution function. The mean downwind velocity is generally one or two orders greater than the mean vertical velocity, but the particle turbulence in the vertical direction is at least two orders greater than that in the downwind direction. In general, the mean downwind velocity increases with height and free‐stream wind velocity, but decreases with grain size. The variation with height of the mean downwind velocity can be expressed by a power function. The particle turbulence of a blowing sand cloud in the downwind direction decreases with height. The variations with height of the mean velocity and particle turbulence in the vertical direction are very complex. It can be concluded that the velocity of a sand cloud blowing over a sandy surface is mainly in?uenced by wind velocity, grain impact with the bed and particle–particle collisions in the air. Wind velocity is the primary factor in?uencing the downwind velocity of a blowing sand cloud, while the grain impact with the bed and particle–particle collisions in the air are the primary factors responsible for the vertical velocity. Copyright © 2004 John Wiley & Sons, Ltd.     

Form–flow interactions of an aeolian saucer blowout

Airflow patterns through a saucer blowout are examined from wind speed and direction measurements made during a chinook wind event. The blowout long‐axis is oriented east–west with a broad depositional apron on the east side. Wind directions during the event rotated from south‐westerly to westerly, permitting an assessment of oblique and axis‐parallel flows. Results show that airflow passing over the windward rim of the saucer blowout expands and decelerates, leading to flow separation and a small re‐circulation zone on sheltered lee slopes. Near the deflation basin, airflow re‐attaches to the blowout surface and accelerates up to a small opening in the east rim, where it can be up to 50% faster than on the windward edge. Beyond the downwind rim the airflow expands and decelerates and sand is deposited onto a broad apron. Similar to coastal trough blowouts, the degree of airflow steering and acceleration along the deflation basin is determined by the angle of incidence between the approach wind and the long‐axis of the blowout. As the angle of incidence increases wind speed accelerates at 0·3 m above the surface of the deflation basin and the degree of airflow steering increases. Overall, a two‐fold process is identified, where south‐westerly flows have greater potential for eroding the deflation basin, while westerly flows have greater potential for evacuating sand from within the blowout. Visual observations indicate that sand eroded from the deflation basin during south‐westerly flows is re‐distributed to adjacent zones of low wind speed until axis‐parallel winds evacuate the sand through the opening in the east rim. Morphometric changes since 1994 indicate that the blowout morphology has remained relatively constant, suggesting a persistent interplay between oblique and axis‐parallel wind erosion events. Collectively, these findings indicate that the angle of approach winds is an important control on saucer blowout morphodynamics. Copyright © 2009 John Wiley & Sons, Ltd.     

Secondary airflow and sediment transport in the lee of a reversing dune

Lee-side windspeed and sediment transport were measured over a small (1·2 m) transverse ridge in the Silver Peak dunefield, west-central Nevada, USA, using an intensive array of 25 cup anemometers and seven total flux traps. During crest-transverse and transporting flow conditions (u_0·3crest ≈ 8·4 m s⁻¹), windspeed near the surface of the lee slope averaged half (48 per cent) that of crest speeds. Dimensionless speeds in the separation zone ranged from 0·2 to 0·8 that of the outer flow (u₁₂). Along the boundary of the separation cell, windspeed increased by 10 per cent of the crest speed before separation. Equilibrium of upper and lower wake regions was not observed by the documented eight dune heights, suggesting that wake recovery may not occur over closely spaced dunes. Sediment transport measured directly on both the lee slope and interdune surfaces averaged approximately 15 per cent of crest inputs. This suggests that a significant amount (c. 70–95 per cent) of sediment transported over the crest moved as fallout. For this data set, flux was approximately proportional to the cube of the near-surface windspeed (u_0·3) and in general there was an order of magnitude difference between flux measured at the crest and that measured within the separation zone. Transport direction in the separation zone was acutely oblique to the incident direction owing to secondary flow deflection. Beyond the interdune, transport direction progressed from oblique to crest-transverse. This indicates that an appreciable amount of sediment may move laterally along the lee slope and interdune corridor under crest-transverse flows. Regarding the grain size and sorting properties of transported sediment, there was no significant difference in mean grain size over the dune, although in general particles were finer and more poorly sorted in the lee. Copyright © 1999 John Wiley & Sons, Ltd.     

Three‐dimensional flow structure around small‐scale bedforms in a simulated gravel‐bed environment

Pebble clusters are common small‐scale morphological features in gravel‐bed rivers, occupying as much as 10 per cent of the bed surface. Important links exist between the presence of pebble clusters and the development of flow structures. These links are poorly understood at the three‐dimensional level. Particularly neglected has been the effect of clusters on the lateral flow characteristics. A laboratory study was conducted using a hydraulic flume, within which simulated pebble clusters were superimposed onto a plane bed of gravel material. High‐resolution three‐dimensional flow data were collected above the bed at two different flow depths using an acoustic Doppler velocimeter. The results present evidence of the importance of lateral flow in the development of turbulent flow structure. Narrow regions of high lateral and downstream turbulence intensity exist to both sides of clusters and in a three‐dimensional separation zone in their lee. This may indicate the presence of horseshoe‐type vortical structures analogous to those identified in less hydraulically rough environments. However, it is likely that these structures are more complicated given the mutual interference of the surrounding medium. The lateral flow was also identified as a key component in the upwelling identified by other authors in the lee of pebble clusters. The results of the vertical flow analysis confirm the hypothesis that six regions with distinct vertical flow characteristics exist above clusters: flow acceleration up the stoss‐side of the cluster; recirculation behind the cluster in the wake region; vortex shedding from the pebble crest and shear layer; flow reattachment downstream of the cluster; upwelling of flow downstream of the point of reattachment; and recovery of flow. Copyright © 2001 John Wiley & Sons, Ltd.     

Assessing aeolian beach‐surface dynamics using a remote sensing approach

A remote sensing technique for assessing beach surface moisture was used to provide insight into beach‐surface evolution during an aeolian event. An experiment was carried out on 21 October 2007 at Greenwich Dunes, Prince Edward Island National Park, Canada, during which cameras were mounted on a mast on the foredune crest at a height of about 14 m above the beach. Maps of beach surface moisture were created based on a calibrated relationship between surface brightness from the photographs and surface moisture content measured in situ at points spaced every 2.5 m along a transect using a Delta‐T moisture probe. A time sequence of maps of surface moisture content captured beach surface evolution through the transport event at a spatial and temporal resolution that would be difficult to achieve with other sampling techniques such as impedance probes. Erosion of the foreshore and berm crest resulted in an increase in surface moisture content in these areas as the wetter underlying sediments were exposed. Flow expansion downwind of the berm crest led to sand deposition and a consequent decrease in surface moisture content. Remote sensing systems such as the one presented here allow observations of the combined evolution of beach surface moisture, shoreline position, and fetch distances during short‐term experiments and hence provide a comprehensive rendering of sediment erosion and transport processes. Copyright © 2012 John Wiley & Sons, Ltd.     

Annual to decadal morphodynamics of the foredune system at Greenwich Dunes,Prince Edward Island,Canada

The purpose of this study was to quantify relationships between season, sediment availability, sediment transport pathways, and beach/foredune morphology at Greenwich Dunes, PEI. This was done for periods ranging from a few days to multiple decades using erosion pins, bedframe measurements, annual surveys, and digital photogrammetry using historical aerial photographs. The relative significance of seasonal/annual processes versus response of the foredune system to broader geomorphic controls (e.g. relative sea level rise, storms, etc.) was also assessed. The data show that there are clear seasonal differences in the patterns of sand supply from the beach to the foredune at Greenwich and that there are differences in sediment supply to the foredune between the east and west reaches of the study area, resulting in ongoing differences in foredune morphology. They also demonstrate that models that incorporate wind climate alone, or even models that include other factors like beach moisture, would not be able to predict the amount of sediment movement from the beach to the foredune in this environment unless there were some way to parameterize system morphology, especially the presence or absence of a dune ramp. Finally, the data suggest that the foredune can migrate landward while maintaining its form via transfers of sediment from the stoss slope, over the crest, and onto the lee slope. Although the rate of foredune development or recovery after disturbance changes over time due to morphological feedback, the overall decadal evolution of the foredune system at Greenwich is consistent with, and supports, the Davidson‐Arnott (2005) conceptual model of dune transgression under rising sea level. Copyright © 2012 John Wiley & Sons, Ltd.     

Aeolian sediment transport and morphologic change on a managed and an unmanaged foredune

Sediment transport and short‐term morphologic change were evaluated at a site where sand fences are deployed and the beach is raked (Managed Site) and a site where these human adjustments are not practiced (Unmanaged Site). Data were gathered across the seaward portion of a low foredune when winds blew nearly shore‐normal at mean speeds 8.9 to 9.3 m s^‐1. Data from traps revealed sediment transport rates at unvegetated portions of the foredune crest (40.2 to 43.5 kg m^‐1 h^‐1) were greater than on the backshore (4.9 to 11.2 kg m^‐1 h^‐1) due to onshore decreases in surface moisture and speed‐up of the wind passing over the foredune. Data from erosion pins indicate sediment input to the dune was 1.48 m³ m^‐1 alongshore at the Managed Site and 1.25 m³ m^‐1 at the Unmanaged Site. The Unmanaged Site had deposition at the dune toe, erosion at mid‐slope, and deposition at the crest. Deposition occurred at mid‐slope on the Managed Site near a partially buried (0.58 m high) fence with a porosity of about 65%. Deposition at partially buried wrack on the upper backshore and dune toe at the Unmanaged Site was about twice as great as deposition in this zone at the Managed Site. Results indicate that: (1) the seaward slope of the foredune can be a more important source of sand to the lee of the crest than the beach; (2) wrack near the toe can decrease transport into the foredune; (3) a scour zone can occur on the foredune slope above the wrack line; (4) a fence placed in this location can promote deposition and offset scour, but fences can restrict delivery of sediment farther inland. Evaluation of alternative configurations of fences and strategies for managing wrack is required to better determine the ways that humans modify foredunes. Copyright © 2012 John Wiley & Sons, Ltd.