砖住宅楼系列模型地震模拟试验设计：多层砖房抗震性能三？…

为保障住户地震安全和进一步研究多层砖房的抗震性能,由企业出资与研究所合作,在三向振动台上进行以四幢砖住宅为一系列的模型试验,本文为其研究论文之一,着重阐述在系列模型的设计中和地震模拟试验中的关键技术以及试验的最终结果。     

悬臂踏步板装配式楼梯多层砖房模型振动台试验研究

介绍了一幢四层砖混结构模型的地震模拟振动台试验，模型为１／４比例，采用悬踏步板装配式楼梯。输入了不同峰值的地震加速度，直至破坏。     

大型三向六自由度地震模拟振动台

大型三向六自由度地震模拟振动台韩俊伟１）李玉亭２）胡宝生２）１）中国哈尔滨１５０００１哈尔滨工业大学２）中国哈尔滨１５００８０国家地震局工程力学研究所主题词地震模拟振动台我国地震模拟振动台（振动台）的研制始于７０年代后期．当时由一机部抗震办、建设部、...     

地震模拟振动台试验系统频率特性估计的研究及应用

系统地分析了在地震模拟振动台试验系统频率特性测试过程中，测量误差，环境对振动台驱动信号的干扰噪声及试验系统本身非线性等因素的影响，得到了对指导试验具有重要意义的结论，阐述了应用试验系统频率特性对试验进行数字补偿控制的方法，并列举一些实例。     

2.5m×2.5m三向六自由度地震模拟振动台系统建设研究

介绍了2.5m×2.5m三向六自由度地震模拟振动台对比国内典型振动台的不同特点。在前期分析与论证工作的基础上,阐述了振动台试验系统的关键组成部分和主要参数的选定、设计原则;通过模态分析和基础动力响应分析,验证了振动台台面及基础设计方案的安全性和合理性;提出了振动台基础预埋件精确定位的方法,可为振动台试验系统建设提供经验和参考依据。     

模型储罐三维地震反应振动台试验研究

针对立式钢制模型罐,进行了三维地震激励和一维地震激励振动台的动响应试验研究。结果表明:储罐在三维地震动激励下的反应与一维激励相比,加速度反应、罐壁的应变反应、储罐提离反应具有较明显的放大效应。位移反应在不同地震激励下,其放大效应不同,El Centro波激励下各测点三维激励下位移较一维激励下位移放大明显,Taft、天津波激励下各测点三维激励下位移较一维激励下位移有放大也有缩小,幅度均不大。由罐壁测点加速度功率谱分析表明:一维激励其峰值频率区域较为集中,主峰突出,能量主要集中于低频区;在三维地震激励下,频率峰值区域明显拉长,峰值点模糊,频率成份十分丰富,表现出多主峰的特点。     

三向地震模拟振动台静力平衡系统的设计与分析

我国自行研制的三向六自由度大型地震模拟振动台采用蓄能器液压马达系统作为其重力平衡装置。用修正的滞弹性模型近似描述蓄能器液压马达系统是合理的，按照静态准则和动态准则设计该系统，确保系统能满足设计要求。本文并对蓄能器流动民达压力控制系统、启动特性和平衡特性进行了分析。     

三向地震作用下砌体结构抗震性能研究

本文首先介绍了两个砌体结构模型在三向地震作用下的地震模拟振动台试验，在此基础上，运用参数识别技术，对试验数据进行了参数识别计算，最后，分析了三向地震作用对砌体结构抗震性能的影响。     

多层砖房底部两层框架抗震变形性能分析

为实现多层砖房底部两层框架结构的加固,需要研究其抗震变形性能。以某底部两层框架、上部四层砖房建筑为对象,通过STRAND7有限元软件构建有限元计算模型,考虑水平荷载与垂直荷载,深入分析多层砖房底部两层框架抗震变形性能。仿真结果表明,建筑结构振型受结构横向楼板刚度的影响较显著,不同振型的频率变化中,X向1阶频率与Y向2阶频率变化最快,楼板平面内弯曲频率变化最慢;整体结构在X向与Y向分别呈现线性剪切变形和弯剪变形,Y向上由于填充墙发挥抗震墙功能,底部两层框架变形较小;在7度多遇地震影响下,底部两层结构中第二层楼板变形较第一层严重,多层砖房底部两层框架建筑结构处于弹性工作状态。     

子结构地震模拟振动台混合试验原理与实现

为了解决地震模拟振动台承载能力及台面尺寸对大型结构试验的限制,扩展振动台的功能,本文提出了子结构地震模拟振动台混合试验方法、试验过程及实时数值积分方法,并给出了试验子结构边界条件的两种模拟形式.通过一个简单框架结构的地震模拟振动台试验和子结构混合加载试验验证了该方法的可行性,并指出了该试验方法的主要技术问题.混合试验方法通过子结构技术和振动台试验相结合,解决了目前的地震模拟振动台试验和拟动力试验在设备规模和加载速度上的局限性.     

钢-混凝土高层结构抗震性能振动台试验研究

广州天誉大厦采用型钢混凝土框架一钢筋混凝土筒体的混合结构体系,地面以上结构采用抗震缝兼伸缩缝分隔为南、北塔两个独立结构体系,南塔高186.5 m,北塔高159.5 m.两塔的核心筒总宽度与核心筒总高的比值均超出了规范限值.为研究这种超限高层混合结构的抗震性能,对其进行了缩尺(1/30)模型的振动台试验,并建立了有限元计...     

大跨度钢桁架转换结构振动台试验研究

以某带高位大跨钢桁架转换结构高层建筑为工程背景,进行了1/25缩尺比例的模型振动台试验,通过粘贴在钢桁架杆件上的应变片,测试了输入不同加速度峰值地震波作用下钢桁架的地震响应。在加速度峰值0.9g地震波作用下,两端支承钢桁架筒体剪力墙才出现裂缝,表明连接部位剪力墙受力性能较好;人工波作用下结构的地震响应最大,层地震作用力在钢桁架转换结构层有突变;试验中随模型结构裂缝发展和抗侧刚度衰减,层地震作用力分布发生变化,其中钢桁架转换结构层承担地震力相对减小,钢桁架应变反应也相对趋缓;钢桁架两端杆件受力较大,表明支承剪力墙对钢桁架的约束作用较大。     

滑动屋盖摩擦控制系统的振动台实验研究

五层钢框架模型的振动台实验表明 ,滑动屋盖摩擦控制系统减震作用显著 ,减震幅度可达 5 0 %以上 ,地震动越强减震效果越好 ;控制系统具有一定的鲁棒性 ,刚度容许大约± 15 %的误差 ,而摩擦系数容许的误差范围更大 ,同时也容许地震强度在一定范围内变化。     

液化场地桩-土-桥梁结构地震相互作用振动台试验数值模拟方法研究

直接针对大型振动台模型试验,建立液化场地桩-土-桥梁结构地震相互作用数值模拟的二维分析模型和计算方法。根据桩基平面应变假定,将空间桩体转换成平面板桩,并考虑桩的尺寸效应;基于桩截面节点位移协调条件和平衡力系等效原理,建立四结点梁单元刚度矩阵且对Timoshenko梁杆单元刚度矩阵进行增广修正,以考虑桩的横向尺寸影响桩周土位移场分布的尺寸效应。根据有效应力原理进行土动反应分析,采用满足M asing准则的修正双曲线模型描述土动力变形的本构关系,同时考虑因孔压上升造成土体软化而对土动力性能的影响,由迭代法处理土的动力非线性。采用并联弹簧-阻尼器模拟计算域人工边界,以考虑边界波的反射作用对体系动力反应的干扰和土粘滞阻尼的影响。采用W ilson-θ逐步积分法计算体系的地震反应。通过与试验结果的对比分析,评估数值模拟的建模途径和计算方法的可靠性。     

Experimental study on the aseismic capacity of a wooden house using shaking table

The aseismic capacity of a typical Korean wooden house built using traditional construction methods is quantitatively estimated. Tenon joints were used in wooden frames. Two 1:4 scale models were tested for rock and soil foundation conditions. Scaled real earthquake time histories were input for the tests. The natural frequency and modal damping ratio of the wooden house in the elastic range were 1·66 Hz and 7 per cent, respectively. The Peak Ground Acceleration (PGA) at the collapse of the house at the soil site was 0·25g, whereas PGA for moderate damage at the rock site was 0·6g. A significant reduction in acceleration response and increase in displacement response was observed for rock and soil foundation conditions, respectively. The wooden house studied is much more vulnerable at soil sites than at rock sites due to the rich low-frequency contents of the input motion and the flexible characteristics of the wooden house. Non-linear dynamic analyses using the modified Double-Target model were compared with test results. The modified Double-Target model appropriately simulates the non-linear inelastic behaviour of a wooden house with tenon joints. Copyright © 1999 John Wiley & Sons, Ltd.     

足尺钢框架振动台试验及动力弹塑性数值模拟

本文通过有限元分析程序OpenSees对一足尺四层钢框架结构进行静力及动力弹塑性分析,结构构件采用自由度较少的纤维模型模拟。在振动台试验之前,预测足尺钢框架结构连续在小震、中震及大震作用下的响应,将预测分析结果与振动台试验结果进行对比,结果显示该数值模拟方法能很好地反映结构的弹塑性行为及破坏机制,准确预测结构的地震响应及大震下结构倒塌时间。这进一步说明基于纤维模型的整体结构弹塑性分析方法,由于自由度数少,适用于整体结构抗震分析。     

Shaking table testing and numerical simulation of the seismic response of a typical Mexican colonial temple

A shaking table testing program was undertaken with the main objective of providing basic information for the calibration of analytical models, and procedures for determining seismic response of typical stone masonry temples of the 16–18th centuries stone masonry construction in Mexico. A typical colonial temple was chosen as a prototype. A model at a 1:8 geometric scale was built with the same materials and techniques as the prototype, and was subjected to horizontal and vertical motions of increasing intensities. The maximum applied intensity corresponded to a base shear force of about 58 of the total building weight. Vertical component of the base motion significantly affected the response and increased the damage of the model. Damage patterns were similar to those observed in actual temples. Damping coefficients of the response ranged from 7 for undamaged state, reached about 14 for severe damage. The main features of the measured response were compared with those computed using a nonlinear, finite element model; for the latter, a constitutive law developed for plain concrete was adopted for reproducing cracking and crushing of the irregular stone masonry. Observed damage patterns as well as measured response could be reproduced with reasonable accuracy by the analytical simulation, except for some local vibrations, as those at the top of the bell towers. It can be concluded that the simple constitutive law adopted for the simulation was able to reproduce the experimental response with reasonable level of accuracy. Copyright © 2011 John Wiley & Sons, Ltd.     

Evaluation of seismic performance of pile‐supported models in liquefiable soils

The seismic performance of four pile‐supported models is studied for two conditions: (i) transient to full liquefaction condition, i.e. the phase when excess pore pressure gradually increases during the shaking; (ii) full liquefaction condition, i.e. defined as the state where the seismically induced excess pore pressure equalises to the overburden stress. The paper describes two complementary analyses consisting of an experimental investigation, carried out at normal gravity on a shaking table, and a simplified numerical analysis, whereby the soil–structure interaction (SSI) is modelled through non‐linear Winkler springs (commonly known as p–y curves). The effects of liquefaction on the SSI are taken into account by reducing strength and stiffness of the non‐liquefied p–y curves by a factor widely known as p‐multiplier and by using a new set of p–y curves. The seismic performance of each of the four models is evaluated by considering two different criteria: (i) strength criterion expressed in terms of bending moment envelopes along the piles; (ii) damage criterion expressed in terms of maximum global displacement. Comparison between experimental results and numerical predictions shows that the proposed p–y curves have the advantage of better predicting the redistribution of bending moments at deeper elevations as the soil liquefies. Furthermore, the proposed method predicts with reasonable accuracy the displacement demand exhibited by the models at the full liquefaction condition. However, disparities between computed and experimental maximum bending moments (in both transient and full liquefaction conditions) and displacement demands (during transient to liquefaction condition) highlight the need for further studies. Copyright © 2016 The Authors Earthquake Engineering & Structural Dynamics Published by John Wiley & Sons Ltd.     

薄弱层设置耗能阻尼器支撑的钢框架模型振动台试验

设计制作了一个五层钢框架模型,在其第一层、第三层和第五层薄弱层分别设置摩擦阻尼器、粘弹性阻尼器和粘弹性-摩擦阻尼器等三种耗能阻尼器支撑,进行了罕遇地震和多遇地震下的振动台试验。试验结果表明,耗能阻尼器支撑能够有效地控制结构的地震反应。     

中国古代木构建筑抗震机理及抗震加固效果的试验研究

为探究中国古代大木作(带有斗栱的木构建筑)结构抗震机理和抗震加固的有效方法，对缩尺比为1／3．52二等材宫殿当心间模型在同样条件下分别进行了模拟地震动的振动台试验研究，测试了模型结构加速度、速度和位移的动力时程响应；模型结构的自震频率和阻尼比。结果表明，古代大木作结构的抗震机理主要表现为两个方面：(i)因柱根滑移而隔震;(ii)斗栱以及普柏枋因弹塑性变形和摩擦滑移消耗掉大量地震能以致结构减轻了震害。