汶川地震滑坡-碎屑流致灾距探讨

为了阐明地震滑坡的运动特性并对其进行致灾距的预测,基于遥感影像解译和野外调查数据,借助经验公式法,分析了汶川地震滑坡水平最大运移距离L与前后缘高差H之间的相关性,给出了经验公式;探讨了不同滑坡之间滑程的差异与异常。结果表明:若已知H,可用L=aH+b或L=aHb对总位移进行预测初探;将视摩擦系数H/L=0.45作为汶川地震高速远程型滑坡的上限较合适;滑坡体积、源区破裂面积与L呈正相关,与H/L呈负相关;地震滑坡易发生在山脊线平行于断裂带、垂直于地震波传播方向的山体两侧;崩塌型滑坡易发前后缘高差范围在10~100m之间,大型高速远程型滑坡易发前后缘高差大于200m;滑坡源区易发坡度分布在25°51°之间,滑床坡降变化范围为0~58°,高速远程型滑坡的滑床坡降主要在8°20°之间;分析认为滑程差异和异常是距离效应、能量传递与岩体挡板效应、滚动润滑与气垫效应、体积与破裂面积效应、地质因子、地形因子、颗粒级配与颗粒流效应等因素综合作用的结果,考虑上述因素有益于滑坡-碎屑流致灾距的预测分析。      

Distribution of debris flows in Glacier National Park,Montana, U.S.A.

The spectacular scenery of Glacier National Park is the result of glacial erosion as well as post-glacial mass wasting processes. Debris flow magnitude and frequency have been established through extensive fieldwork across seven separate drainage basins in the eastern portion of the park. This paper summarizes the investigation of the hypotheses that debris flow distribution in the Glacier National Park, east of the Continental Divide is （a） not random; and Co） concentrated adjacent to the Continental Divide. The location of 2317 debris flows were identified and mapped from sixty-three 1-m resolution Digital Orthophoto Quarter Quadrangles and their spatial distribution was then analyzed using ArcView Spatial Analyst GIS software. The GIS analysis showed that the debris flows are not randomly distributed nor are they concentrated directly adjacent to the Divide. While the Continental Divide provides orographic enhancement of precipitation directly adjacent to the Divide, the debris flows are not concentrated there due to a lack of available weathered regolith. The most recent Little Ice Age glaciation removed the debris directly adjacent to the Divide, and without an adequate debris supply, these steep slopes experience few debris flows. Both abundant water and an adequate debris supply are necessary to initiate slope failure, resulting in a clustering of debris flows at the break in slope where valley walls contact talus slopes. A variety of summer storm and antecedent moisture conditions initiate slope failures in the Glacier National Park, with no distinct meteorological threshold. With over two million visitorsevery year, and millions of dollars of park infrastructure at risk, identifying the hazard of debris flows is essential to future park management plans.     

Mass-front velocity of dry granular flows influenced by the angle of the slope to the runout plane and particle size gradation

The mass-front velocities of granular flows results from the joint action of particle size gradations and the underlying surfaces.However,because of the complexity of friction during flow movement,details such as the slope-toe impedance effects and momentum-transfer mechanisms have not been completely explained by theoretical analyses,numerical simulations,or field investigations.To study the mass-front velocity of dry granular flows influenced by the angle of the slope to the runout plane and particle size gradations we conducted model experiments that recorded the motion of rapid and long-runout rockslides or avalanches.Flume tests were conducted using slope angles of 25°,35°,45°,and 55° and three particle size gradations.The resulting mass-front motions consisted of three stages:acceleration,velocity maintenance,and deceleration.The existing methods of velocity prediction could not explain the slowing effect of the slope toe or the momentum-transfer steady velocity stage.When the slope angle increased from 25° to 55°,the mass-front velocities dropped significantly to between 44.4% and59.6% of the peak velocities and energy lossesincreased from 69.1% to 83.7% of the initial,respectively.The velocity maintenance stages occurred after the slope-toe and mass-front velocity fluctuations.During this stage,travel distances increased as the angles increased,but the average velocity was greatest at 45°.At a slope angle of 45°,as the median particle size increased,energy loss around the slope toe decreased,the efficiency of momentum transfer increased,and the distance of the velocity maintenance stage increased.We presented an improved average velocity formula for granular flow and a geometrical model of the energy along the flow line.     

Influence factors on the seismic behavior and deformation modes of gravity retaining walls

This study investigated the influence factors on the seismic response and deformation modes of retaining walls using large-scale model shaking table tests. Experimental results showed that the distribution of peak seismic earth pressures along the height of a wall was a single peak value curve. The seismic earth pressures on a gravel soil retaining wall were larger than the pressures on the weathered granite and quartz retaining walls. Also, the peak seismic earth pressure increased with increases in the peak ground acceleration and the wall height. The measured seismic active earth pressures on a rock foundation retaining wall were larger than the calculated values, and the action position of resultant seismic pressure was higher than 0.33 H. In the soil foundation retaining wall, the measured seismic earth pressures were much smaller than the calculated values, while the action position was slightly higher than 0.33 H. The soil foundation retaining wall suffered base sliding and overturning under earthquake conditions, while overturning was the main failure mode for the rock foundation retaining walls.     

Slope debris flows in the Wenchuan Earthquake area

Avalanches and landslides, induced by the Wenchuan Earthquake on May 12, 2008, resulted in a lot of disaggregated, solid material on slopes that could be readily mobilized as source material for debris flows. Rainstorms triggered numerous slope debris flows with great damage to highways and rivers over the subsequent two years. Slope debris flows (as opposed to channelized debris flows) are defined as phenomena in which high-concentration mixtures of debris and water flow down slopes for short distances to highways and river banks. Based on field investigations and measurements of 19 slope debris flows, their main characteristics and potential mitigation strategies were studied. High rainfall intensity is the main triggering factor. Critical rainfall intensities for simultaneous occurrence of single, several and numerous slope debris flow events were 20 mm/day, 30mm/day, and 90 mm/day, respectively. Field investigations also revealed that slope debris flows consist of high concentrations of cobbles, boulders and gravel. They are two-phase debris flows. The liquid phase plays the role of lubrication instead of transporting medium. Solid particles collide with each other and consume a lot of energy. The velocities of slope debris flows are very low, and their transport distances are only several tens of meters. Slope debris flows may be controlled by construction of drainage systems and by reforestation.     

Debris flow in metropolitan area — 2011 Seoul debris flow

A large number of debris flows occurred simultaneously at around 8:30 to 8:50 a.m. on July 27, 2011, at the center of Seoul, Korea. This area is located in the southern part of Seoul and is a densely populated district. As a result of the debris flow event, 16 people were killed, 30 houses were buried, and 116 houses were damaged around Umyeon Mountain, a relatively small mountain with a height of 312.6 m. Since the debris flow event, field investigations on the initiation and transportation zones of debris flows have been carried out. Rainfall data were collected from the automatic weather stations (AWSs) which are operated by the Korea Meteorological Administration (KMA). Video files recorded by residents were also acquired and used to analyze the flow characteristics of the debris flow. Field investigation shows that about 40 debris flows occurred around Umyeon Mountain and most of the debris flows were initiated by small slope failures. The effects of the precipitation that triggered the debris flows were analyzed as well. A landslide hazard map which considers slope gradient and aspect, strength of soil, hazard record, rainfall conditions, and vegetation, was constructed and compared with the initiation zones of debris flows.     

藏东南多依弄巴流域冰湖溃决危险性评价

冰湖溃决灾害是指冰湖坝体突然破坏引发溃决洪水或溃决泥石流的现象,对下游人类活动和自然环境造成严重影响。近年来,藏东南地区冰川快速退缩,冰湖数量和规模显著增加,冰湖溃决事件广泛发生。基于1995-2021年多时相Landsat系列遥感影像、Sentinel-2A遥感影像,结合RAMMS水文动力学模型方法,对藏东南地区多依弄巴流域内冰湖、冰川进行动态变化分析,模拟冰崩危险体触发冰湖溃决和冰湖溃决泥石流的演进过程,根据泥石流模拟中的流速和流深对冰湖溃决可能影响的区域进行危险性分区。结果表明:流域内冰川面积由1995年的14.05 km2退缩为2021年的9.43 km2,年均退缩率约为0.15 km2/a。流域内共发育3处冰崩危险体,均可能触发冰湖溃决。潜在危险冰湖在全溃情况下,溃决泥石流会冲出沟口堵塞然乌湖湖口和帕隆藏布主河道,对下游居民和道路造成影响,影响范围约4.05 km2,其中高危险性区域约2.55 km2。危险性评价结果可为多依弄巴流域未来土地利用规划和防灾减灾提供依据,也能为藏东南地区冰湖溃决型泥石流危险评估提供参考。      

Effects of loose deposits on debris flow processes in the Aizi Valley,southwest China

Loose deposits, rainfall and topography are three key factors that triggering debris flows.However, few studies have investigated the effects of loose deposits on the whole debris flow process.On June 28, 2012, a catastrophic debris flow occurred in the Aizi Valley, resulting in 40 deaths.The Aizi Valley is located in the Lower Jinsha River,southwestern Sichuan Province, China. The Aizi Valley debris flow has been selected as a case for addressing loose deposits effects on the whole debris flow process through remote sensing, field investigation and field experiments. Remote sensing interpretation and laboratory experiments were used to obtain the distribution and characteristics of the loose deposits, respectively. A field experiment was conducted to explore the mechanics of slope debris flows, and another field investigation was conducted to obtain the processes of debris flow formation, movement and amplification. The results showed that loose deposits preparation, slope debris flow initiation,gully debris flow confluence and valley debris flow amplification were dominated by the loose deposits.Antecedent droughts and earthquake activities may have increased the potential for loose soil sources in the Aizi Valley, which laid the foundation for debris flow formation. Slope debris flow initiated under rainfall, and the increase in the water content as well as the pore water pressure of the loose deposits were the key factors affecting slope failure. The nine gully debris flows converged in the valley, and the peak discharge was amplified 3.3 times due to a blockage and outburst caused by a large boulder. The results may help in predicting and assessing regional debris flows in dry-hot and seismic-prone areas based on loose deposits, especially considering large boulders.     

An experimental study: Integration device of Fiber Bragg grating and reinforced concrete beam for measuring debris flow impact force

The impact effect of boulder within debris flow is the key factor contributing to peak impact as well as to the failure of debris flow control work. So accurate measuring and calculating the impact force of debris flow can ensure the engineering design strength. However, limited to the existing laboratory conditions and piezoelectric sensor performance, it is impossible, based on the conventional measurements, to devise a computing method for expressing a reliable boulder impact force. This paper has therefore designed a new measurement device according to the method of integrating Fiber Bragg grating (FBG) and reinforced concrete composite beam (RCB) for measuring the impact force of debris flows, i.e. mounting FBG on the axially stressed steel bar in the composite beam at regular intervals to monitor the steel strain. RCB plays the role of contacting debris flow and protecting FBG sensors. Taking this new device as the experimental object, drop testing is designed for simulating and reflecting the boulder impact force. In a series of impacting tests, the relationship between the peak dynamic strain value of the steel bar and the impact force is analyzed, and based on which, an inversion model that uses the steel bar strain as the independent variable is established for calculating the boulder impact force. The experimental results show that this new inversion model can determine the impact force value and its acting position with a system error of 18.1%, which can provide an experimental foundation for measuring the impact force of boulders within the debris flow by the new FBG-based device.     

Mechanisms involved in triggering debris flows within a cohesive gravel soil mass on a slope: a case in SW China

The triggering mechanisms of debris flows were explored in the field using artificial rainfall experiments in two gullies, Dawazi Gully and Aizi Gully, in Yunnan and Sichuan Provinces, China, respectively. The soils at both sites are bare, loose and cohesive gravel-dominated. The results of a direct shear test, rheological test and back-analysis using soil mass stability calculations indicate that the mechanisms responsible for triggering debris flows involved the decreases in static and dynamic resistance of the soil. The triggering processes can be divided into 7 stages: rainfall infiltration, generation of excess runoff, high pore water pressure, surface erosion, soil creep, soil slipping, debris flow triggering and debris flow increment. In addition, two critical steps are evident: (i) During the process of the soil mass changing from a static to a mobile state, its cohesion decreased sharply (e.g., the cohesion of the soil mass in Dawazi Gully decreased from 0.520 to 0.090 kPa, a decrease of 83%). This would have reduced the soil strength and the kinetic energy during slipping, eventually triggered the debris flow. (ii) When the soil mass began to slip, the velocity and the volume increment of the debris flow fluctuated as a result of the interaction of soil resistance and the sliding force. The displaced soil mass from the source area of the slope resulted in the deposition of a volume of soil more than 7 - 8 times greater than that in the source area.     

Early warning model for slope debris flow initiation

Early warning model of debris flow is important for providing local residents with reliable and accurate warning information to escape from debris flow hazards. This research studied the debris flow initiation in the Yindongzi gully in Dujiangyan City, Sichuan province, China with scaled-down model experiments. We set rainfall intensity and slope angle as dominating parameters and carried out 20 scaled-down model tests under artificial rainfall conditions. The experiments set four slope angles(32°, 34°, 37°, 42°) and five rainfall intensities(60 mm/h, 90 mm/h, 120 mm/h, 150 mm/h, and 180 mm/h) treatments. The characteristic variables in the experiments, such as, rainfall duration, pore water pressure, moisture content, surface inclination, and volume were monitored. The experimental results revealed the failure mode of loose slope material and the process of slope debris flow initiation, as well as the relationship between the surface deformation and the physical parameters of experimental model. A traditional rainfall intensity-duration early warning model(I-D model) was firstly established by using a mathematical regression analysis, and it was then improved into ISD model and ISM model(Here, I is rainfall Intensity, S is Slope angle, D is rainfall Duration, and M is Moisture content). The warning model can provide reliable early warning of slope debris flow initiation.     

Limit analysis method for active earth pressure on laggings between stabilizing piles

Stabilizing pile is a kind of earth shoring structure frequently used in slope engineering. When the piles have cantilever segments above the ground, laggings are usually installed to avoid collapse of soil between piles. Evaluating the earth pressure acting on laggings is of great importance in design process. Since laggings are usually less stiff than piles, the lateral pressure on lagging is much closer to active earth pressure. In order to estimate the lateral earth pressure on lagging more accurately, first, a model test of cantilever stabilizing pile and lagging systems was carried out. Then, basing the experimental results, a three-dimensional sliding wedge model was established. Last, the calculation process of the total active force on lagging is presented based on the kinematic approach of limit analysis. A comparison is made between the total active force on lagging calculated by the formula presented in this study and the force on a same-size rigid retaining wall obtained from Rankine's theory. It is found that the proposed method fits well with the experimental results. Parametric studies show that the total active force on lagging increases with the growth of the lagging height and the lagging clear span; while decreases as the soil internal friction angle and soil cohesion increase.     

Experimental study on the energy dissipation characteristics of debris flow deceleration baffles

Debris flow can cause serious damages to roads, bridges, buildings and other infrastructures.Arranging several rows of deceleration baffles in the significant influence on the mobility and deposition characteristic of debris flow. The deposit amount first increased then decreased when the flow density rises,flow path can reduce the flow velocity and ensure better protection of life and property. In debris flow prevention projects, deceleration baffles can effectively reduce the erosion of the debris flow and prolong the running time of the drainage channel.This study investigated the degree to which a 6 m long flume and three rows of deceleration baffles reduce the debris flow velocity and affect the energy dissipation characteristics. The influential variables include channel slope, debris flow density, and spacing between baffle rows. The experimental results demonstrated that the typical flow pattern was a sudden increase in flow depth and vertical proliferation when debris flow flows through the baffles. Strong turbulence between debris flow and baffles can contribute to energy dissipation and decrease the kinematic velocity considerably. The results showed that the reduction ratio of velocity increased with the increase in debris flow density,channel slope and spacing between rows. Tests phenomena also indicated that debris flow density hasand the deposit amount of debris flow density of 1500kg/m~3 reached the maximum when the experimental flume slope is 12°.     

京广铁路K1219路基土质边坡深层滑移失稳机制与整治对策

为研究土质边坡深层滑移失稳机制, 以京广铁路下行线K1219+000处路基边坡失稳为例, 通过现场调查测绘、工程地质钻探、原位试验和室内试验、深部位移监测和数值模拟等手段, 详细研究了该土质边坡变形破坏特征、地质力学过程和失稳模式。结果表明: 路基边坡表面裂缝宽度及深度呈坡顶至坡脚逐渐变浅变窄, 变形具有一定的旋转性, 牵引式特征明显, 属于深层滑移拉裂式失稳; 土质边坡经历了因坡脚开挖、抽水引起的应力场和渗流场重新分布阶段、雨水入渗软化导致下滑力不断增大而滑面逐渐迁移扩大加深阶段以及支挡结构抗力失效阶段3个地质力学过程, 其失稳模式包括浅层滑移、浅层滑面向深层迁移、动荷载触发深层滑移失稳3个阶段。在此基础上, 综合确定了滑面位置, 并通过反演方法确定了滑面力学参数。研究采用了刚架式双排抗滑桩的整治方案, 通过理论计算和数值分析, 边坡变形与抗滑桩变形基本一致, 且与监测结果整体吻合, 这表明土质边坡深层失稳理论分析准确且计算的力学参数科学, 整治对策稳妥、可靠。      

GIS tools for preliminary debris-flow assessment at regional scale

The assessment of the areas endangered by debris flows is a major issue in the context of mountain watershed management. Depending on the scale of analysis, different methods are required for the assessment of the areas exposed to debris flows. While 2-D numerical models are advised for detailed mapping of inundation areas on individual alluvial fans, preliminary recognition of hazard areas at the regional scale can be adequately performed by less data-demanding methods, which enable priority ranking of channels and alluvial fans at risk by debris flows. This contribution focuses on a simple and fast procedure that has been implemented for regional-scale identification of debris-flow prone channels and prioritization of the related alluvial fans. The methodology is based on the analysis of morphometric parameters derived from Digital Elevation Models (DEMs). Potential initiation sites of debris flows are identified as the DEM cells that exceed a threshold of slope-dependent contributing area. Channel reaches corresponding to debris flows propagation, deceleration and stopping conditions are derived from thresholds of local slope. An analysis of longitudinal profiles is used for the computation of the runout distance of debris flows. Information on erosion-resistant bedrock channels and sediment availability surveyed in the field are taken into account in the applications. A set of software tools was developed and made available (https://github.com/HydrogeomorphologyTools) to facilitate the application of the procedure. This approach, which has been extensively validated by means of field checks, has been extensively applied in the eastern Italian Alps. This contribution discusses potential and limitations of the method in the frame of the management of small mountain watersheds.     

Mutual Interference of Two Debris Flow Deposits Delivered in a Downstream River Reach

We investigate experimentally the depositions of two contiguous debris flows flowing into a main river reach.The aim of the present experimental research is to analyze the geometry and the mutual interactions of debris flow deposits conveyed by these tributaries in the main channel.A set of 19 experiments has been conducted considering three values of the confluence angle,two slopes of the tributary,and three different triggering conditions（debris flows occurring simultaneously in the tributaries,or occurring first either in the upstream or in the downstream tributary）.The flow rate along the main channel was always kept constant.During each experiment the two tributaries had the same slope and confluence angle.The analysis of the data collected during the experimental tests indicates that the volume of the debris fan is mainly controlled by the slope angle,as expected,while the shape of the debris deposit is strongly influenced by the confluence angle.Moreover,in the case of multiple debris flows,the deposit shape is sensitive to the triggering conditions.Critical index for damming formation available in literature has been considered and applied to the present case,and,on the basis of the collected data,considerations about possible extension of such indexes to the case of multiple confluences are finally proposed.     

Investigation and Assessment of Landslides and Debris Flows in Sichuan Province of China by Remote Sensing Technique

Taking TM images, ETM images, SPOT images, aerial photos and other remote sensing data as fundamental sources, this research makes a thorough investigation on landslides and debris flows in Sichuan Province, China, using the method of manual interpretation and taking topography maps as references after the processes of terrain correction, spectral matching, and image mosaic. And then, the spatial characteristics of landslides and debris flows in the year of 2005 are assessed and made into figures. The environmental factors which induce landslides and debris flows such as slope, vegetation coverage, lithology, rainfall and so on are obtained by GIS spatial analysis method. Finally, the relationships of landslides or debris flows with some environmental factors are analyzed based on the grade of each environmental factor. The results indicate： 1） The landslides and debris flows are mainly in the eastern and southern area of Sichuan Province, however, there are few landslides and debris flows in the western particularly the northwestern Sichuan. 2） The landslides and debris flows of Sichuan Province are mostly located in the regions with small slope degree. The occurring rate of debris flow reduces with the increase of the vegetation coverage degree, but the vegetation coverage degree has little to do with the occurrence of landslide. The more rainfall a place has, the easier the landslides and debris flows take place.     

Debris flow dam formation in Southeast Tibet

1 Introduction Debris flows in Southeast Tibet can carry a great deal of sediment into streams in a special way. They block mainstreams and form dams.This type of dam,not only dominates the interaction between water and sediment and changes in the riverbed, but also exerts a great influence on the ability of transportation of the river. When a debris-flow dam forms, the water level behind the dam will increase, and villages, fields and roads will beflooded.When the dam breakes,the resulting …     

降雨模式对震后泥石流起动模式影响的试验研究: 以九寨天堂沟为例

降雨过程中降雨强度的变化会影响土体渗透率及饱和过程, 从而改变土体的力学性质, 影响泥石流起动模式及破坏规模。为探究不同降雨模式对震后泥石流起动机制的影响, 自制了小比例模型槽, 结合可控雨型的降雨模拟系统, 进行了人工降雨诱发泥石流的室内模型试验; 基于不同降雨模式下泥石流的起动过程分析, 对坡体内部含水率和孔隙水压力的变化规律进行了研究。研究结果表明: 递增型降雨模式下泥石流发生突然, 呈整体滑坡转化为泥石流起动模式, 坡体破坏规模最大; 递减型降雨模式下表现为后退式溃散失稳起动模式; 均匀型降雨模式下则表现为溯源侵蚀起动模式; 中峰型降雨模式下以局部滑坡转化为泥石流起动模式; Ⅴ型降雨模式下则由坡面侵蚀加剧转化为泥石流启动模式, 破坏规模最小。研究结果可以为九寨沟地区泥石流的预报预警提供参考。      

Debris flows introduced in landslide deposits under rainfall conditions: The case of Wenjiagou gully

Debris flows often occur in landslide deposits during heavy rainstorms. Debris flows are initiated by surface water runoff and unsaturated seepage under rainfall conditions. A physical model based on an infinitely long, uniform and void-rich sediment layer was applied to analyze the triggering of debris-flow introduced in landslide deposits. To determine the initiation condition for rainfall-induced debris flows, we conducted a surface water runoff and saturated-unsaturated seepage numerical program to model rainfall infiltration and runoff on a slope. This program was combined with physical modeling and stability analysis to make certain the initiation condition for rainfall-introduced debris flows. Taking the landslide deposits at Wenjiagou gully as an example, the initiation conditions for debris flow were computed. The results show that increase height of surface-water runoff and the decrease of saturated sediment shear strength of are the main reasons for triggering debris-flows under heavy rainfall conditions. The debris-flow triggering is affected by the depth of surface-water runoff, the slope saturation and shear strength of the sediment.