THE USE OF SEISMIC SHEAR WAVES AND COMPRESSIONAL WAVES FOR LITHOLOGICAL PROBLEMS OF SHALLOW SEDIMENTS*

From a great variety of in situ shear wave experiments, i.e., reflection, refraction and borehole surveys in the shallow sediments of the north German plains, several specific properties have been derived. Shear waves (S) differ from compressional waves (P) in that:

• 1 they are not affected by the degree of water saturation. Thus, they provide a better correlation between the velocity V_s and (solid) lithology;
• 2 they generally have lower frequencies, but shorter wavelength and, hence, a better resolution of thin layers;
• 3 they have lower absorption Q_s^?1 and hence a better penetration in partially saturated and gas-containing sediments than P-waves.

Correlations have been established between V_s and the confining pressure and between reduced V_s values and several lithological parameters like the grain size of sandy material. More lithological and hydrological information is obtained by using S- and P-wave surveys along the same profile. The best information on a sedimentological structure is obtained by the simultaneous observation of V_s, V_p, Q_s and Q_p.     

Determining Q of near-surface materials from Rayleigh waves

High-frequency (≥2 Hz) Rayleigh wave phase velocities can be inverted to shear (S)-wave velocities for a layered earth model up to 30 m below the ground surface in many settings. Given S-wave velocity (V_S), compressional (P)-wave velocity (V_P), and Rayleigh wave phase velocities, it is feasible to solve for P-wave quality factor Q_P and S-wave quality factor Q_S in a layered earth model by inverting Rayleigh wave attenuation coefficients. Model results demonstrate the plausibility of inverting Q_S from Rayleigh wave attenuation coefficients. Contributions to the Rayleigh wave attenuation coefficients from Q_P cannot be ignored when Vs/V_P reaches 0.45, which is not uncommon in near-surface settings. It is possible to invert Q_P from Rayleigh wave attenuation coefficients in some geological setting, a concept that differs from the common perception that Rayleigh wave attenuation coefficients are always far less sensitive to Q_P than to Q_S. Sixty-channel surface wave data were acquired in an Arizona desert. For a 10-layer model with a thickness of over 20 m, the data were first inverted to obtain S-wave velocities by the multichannel analysis of surface waves (MASW) method and then quality factors were determined by inverting attenuation coefficients.     

VISCOELASTIC SEISMIC RESPONSES OF 2D RESERVOIR MODELS1

The use of relaxation mechanisms has recently made it possible to simulate viscoelastic (Q) effects accurately in time-domain numerical computations of seismic responses. As a result, seismograms may now be synthesized for models with arbitrary spatial variations in compressional- and shear-wave quality factors (Q₉, and Q_s, as well as in density (ρ) and compressional- and shear-wave velocities (V_p, and V_s). Reflections produced by Q contrasts alone may have amplitudes as large as those produced by velocity contrasts. Q effects, including their interaction with V_p, V_s and p, contribute significantly to the seismic response of reservoirs. For band-limited data at typical seismic frequencies, the effects of Q on reflectivity and attenuation are more visible than those on dispersion. Synthetic examples include practical applications to reservoir exploration, evaluation and monitoring. Q effects are clearly visible in both surface and offset vertical seismic profile data. Thus, AVO analyses that neglect Q may produce erroneous conclusions.     

Measuring wave propagation characteristics in artificial sand-clay mixtures

Ultrasonic compressional (V _p ) and shear (V _s ) velocities have been measured on artificial sand-clay mixtures. The measurements were carried out in a drained triaxial load cell using a pulse transition method. The measuring device was equiped with a waveform storage facility. The investigated mixtures consisted mainly of kaolinite and quartz sand. Some mixtures also contained Na-montmorillonite, illites or quartz-flour. The acoustic behaviour was observed during a pressure increase up to 72 MPa vertical and 36 MPa horizontal pressure. At a given pressure,V _p andV _s in pure sand turned out to be similar to those in pure kaolinite. As predicted by the sand-clay model of Marion (1990), a velocity maximum corresponds to a minimum in total porosity. This porosity minimum marks the transition from a clayey sand to a sandy clay. It is not only reflected in bothV _p andV _s , but also in the quality of the received pulse. The effective tension of the received signal during 20µs after the first arrival, was used as an indication for P-wave pulse attenuation. This apparent attenuation decreases with increasing clay content and increases with increasing porosity. It is shown that clay mineralogy does not measurably affect wave velocities in clayey sands.     

Modelling shear waves in OBS data from the Vøring basin (Northern Norway) by 2-D ray-tracing

Three component recordings from an array of five ocean bottom seismographs in the northwestern part of the Vøring basin have been used to obtain a 2-D shear-wave (S-wave) velocity-depth model. The shear waves are identified by means of travel-time differences compared to the compressional (P) waves, and by analyzing their particle motions. The model has been obtained by kinematic (travel-time) ray-tracing modelling of the OBS horizontal components.The shear-wave modelling indicates that mode conversions occur at several high velocity interfaces (sills) in the 4–10 km depth range, previously defined by a compressional-wave velocity-depth model using the same data set.An averageV _p /V _s ratio of 2.1 is inferred for the layers above the uppermost sill, indicative of both poorly consolidated sediments and a low sand/shale ratio. A significant decrease in theV _p /V _s ratio (1.7) below the first sill may in part be atributed to well consolidated sediments, and to a change in lithology to more sandy sediments. This layer is interpreted to lie within the lower Cretaceous sequence. At 5–10 km depthV _p /V _s ratios of 1.85 indicate a lower sand/shale ratio consistent with the expected lithologies. The averageV _p /V _s ratio inferred for the crust is 1.75, which is consistent with values obtained north of Vøring, in the Lofoten area. An eastward thinning of the crystalline basement is supported by the shear-wave modelling.     

A PHYSICAL MODEL STUDY OF SCATTERING OF WAVES BY ALIGNED CRACKS: COMPARISON BETWEEN EXPERIMENT AND THEORY1

An approximation to plane-wave propagation through a composite material is examined using a physical model with oriented but randomly distributed penny-shaped rubber inclusions within an isotropic epoxy resin matrix. A pulse transmission method is used to determine velocities of shear and compressional waves as a function of angle of incidence and crack density. The experimental and theoretical results of Hudson were compared and limitations within the crack parameters used in this study have been determined. Results from both polarized shear waves (S1, S2) compare favourably with the theory for a composite with up to 7% crack density, but theory and experiment diverge at higher crack densities. On the other hand, compressional-wave velocities at low crack densities (1% and 3%) compare favourably with the theory. It is also shown that the velocity ratio V_p/V_s for two extreme cases, i.e. propagation normal and parallel to the cracks, as a function of crack density and porosity, has a strong directional dependence.     

Vp‐Vs relationship and amplitude variation with offset modelling of glauconitic greensand‡

The relationship between V_p and V_s may be used to predict V_s where only V_p is known. V_p/V_s is also used to identify pore fluids from seismic data and amplitude variation with offset analysis. Theoretical, physical, as well as statistical empirical V_p‐V_s relationships have been proposed for reservoir characterization when shear‐wave data are not available. In published work, the focus is primarily on the V_p‐V_s relationship of quartzitic sandstone. In order to broaden the picture we present V_p‐V_s relationships of greensand composed of quartz and glauconite by using data from the Paleocene greensand Nini oil field in the North Sea. A V_p‐V_s relationship derived from modelling is compared with empirical V_p‐V_s regressions from laboratory data as well as from log data. The accuracy of V_s prediction is quantified in terms of root‐mean‐square error. We find that the V_p‐V_s relationship derived from modelling works well for greensand shear‐wave velocity prediction. We model the seismic response of glauconitic greensand by using laboratory data from the Nini field. Our studies here reveal that brine‐saturated glauconitic greensand can have a similar seismic response to that from oil‐saturated quartzitic sandstone and that oil‐saturated strongly cemented greensand can have a similar amplitude variation with offset response to that from brine‐saturated weakly cemented greensand.     

Borehole study of compressional and shear attenuation of basalt flows penetrated by the Brugdan and William wells on the Faroes shelf

We investigated the seismic attenuation of compressional (P‐) and converted shear (S‐) waves through stacked basalt flows using short‐offset vertical seismic profile (VSP) recordings from the Brugdan (6104/21–1) and William (6005/13–1A) wells in the Faroe‐Shetland Trough. The seismic quality factors (Q) were evaluated with the classical spectral ratio method and a root‐mean‐square time‐domain amplitude technique. We found the latter method showed more robust results when analysing signals within the basalt sequence. For the Brugdan well we calculated effective Q estimates of 22–26 and 13–17 for P‐ and S‐waves, respectively, and 25–33 for P‐waves in the William well. An effective Q_S/Q_P ratio of 0.50–0.77 was found from a depth interval in the basalt flow sequence where we expect fully saturated rocks. P‐wave quality factor estimates are consistent with results from other VSP experiments in the North Atlantic Margin, while the S‐wave quality factor is one of the first estimates from a stacked basalt formation using VSP data. Synthetic modelling demonstrates that seismic attenuation for P‐ and S‐waves in the stacked basalt flow sequence is mainly caused by one‐dimensional scattering, while intrinsic absorption is small.     

IMPROVEMENTS IN THE OBSERVATION OF SHEAR WAVES*

The observation of shear waves is finding more interest in seismic exploration, especially for the determination of additional lithologic parameters, e.g. V^p/V^s. We demonstrate the observation of converted waves in routine seismic work by means of horizontal geophones. Field technique and data processing permit acquisition and interpretation of converted waves in connection with routine seismic measurements. A special interpretation of the recorded converted waves results in the shear wave velocity and the V^p/V^s relation.     

Use of mode-converted waves in marine seismic data to investigate the lithology of the sub-bottom sediments in Isfjorden,Svalbard

The compression wavefield is efficiently converted to shear-wave energy at post-critical angles in areas of high impedance contrast at the sea floor. We have analysed mode-converted shear waves in a data set acquired with a hybrid marine/land geometry in Isfjorden, Svalbard. Through a kinematic 2D ray-tracing modellingV _p/V_s ratios for part of the uppermost 5km of the crust are obtained. Low values (V _p /V _s =1.65) are tentatively associated with the section of Devonian sandstones which appears to attain a minimum thickness of 1.5km below 3 km depth about 10km west of Kapp Thorden.     

AN ULTRASONIC PROFILING INVESTIGATION ON SOME FRESH AND WEATHERED GRANITES OF HYDERABAD,INDIA*

The ultrasonic profiling method of measuring the compressional and shear wave velocities in cylindrical rock samples is extended to measurements in some weathered and fresh granite blocks collected from the Hyderabad (India) region. This possibility of the method provides a means of investigating the elastic properties of the less compact rocks, of which the near-surface formations are particularly important. In this article the important parts of the ultrasonic profiling instrument developed are described and the relevant aspects of the seismic wave fields and identification of the individual waves in the wavetrain responses to longitudinal excitation are considered. Compressional, shear and surface (Rayleigh) wave velocities in some fresh and weathered granites are detailed. The compressional velocities range from 4.8 km/s to 5.5 km/s in fresh granites and lie between 1.1 km/s and 2.5 km/s in weathered granites. Young's modulus and Poisson's ratios computed from the measured velocities are also presented. An empirical relation of the form log E= 4.27 + 2.11 log V_p between Young's modulus E and compressional velocities V_p in the fresh granites studied is deduced. The versatility of the approach is thus demonstrated.     

Velocities of compressional and shear waves in limestones

Carbonate rocks are important hydrocarbon reservoir rocks with complex textures and petrophysical properties (porosity and permeability) mainly resulting from various diagenetic processes (compaction, dissolution, precipitation, cementation, etc.). These complexities make prediction of reservoir characteristics (e.g. porosity and permeability) from their seismic properties very difficult. To explore the relationship between the seismic, petrophysical and geological properties, ultrasonic compressional‐ and shear‐wave velocity measurements were made under a simulated in situ condition of pressure (50 MPa hydrostatic effective pressure) at frequencies of approximately 0.85 MHz and 0.7 MHz, respectively, using a pulse‐echo method. The measurements were made both in vacuum‐dry and fully saturated conditions in oolitic limestones of the Great Oolite Formation of southern England. Some of the rocks were fully saturated with oil. The acoustic measurements were supplemented by porosity and permeability measurements, petrological and pore geometry studies of resin‐impregnated polished thin sections, X‐ray diffraction analyses and scanning electron microscope studies to investigate submicroscopic textures and micropores. It is shown that the compressional‐ and shear‐wave velocities (V_p and V_s, respectively) decrease with increasing porosity and that V_p decreases approximately twice as fast as V_s. The systematic differences in pore structures (e.g. the aspect ratio) of the limestones produce large residuals in the velocity versus porosity relationship. It is demonstrated that the velocity versus porosity relationship can be improved by removing the pore‐structure‐dependent variations from the residuals. The introduction of water into the pore space decreases the shear moduli of the rocks by about 2 GPa, suggesting that there exists a fluid/matrix interaction at grain contacts, which reduces the rigidity. The predicted Biot–Gassmann velocity values are greater than the measured velocity values due to the rock–fluid interaction. This is not accounted for in the Biot–Gassmann velocity models and velocity dispersion due to a local flow mechanism. The velocities predicted by the Raymer and time‐average relationships overestimated the measured velocities even more than the Biot model.     

Acoustic and petrophysical relationships in low-shale sandstone reservoir rocks

This paper describes the measurements of the acoustic and petrophysical properties of two suites of low‐shale sandstone samples from North Sea hydrocarbon reservoirs, under simulated reservoir conditions. The acoustic velocities and quality factors of the samples, saturated with different pore fluids (brine, dead oil and kerosene), were measured at a frequency of about 0.8 MHz and over a range of pressures from 5 MPa to 40 MPa. The compressional‐wave velocity is strongly correlated with the shear‐wave velocity in this suite of rocks. The ratio V_P/V_S varies significantly with change of both pore‐fluid type and differential pressure, confirming the usefulness of this parameter for seismic monitoring of producing reservoirs. The results of quality factor measurements were compared with predictions from Biot‐flow and squirt‐flow loss mechanisms. The results suggested that the dominating loss in these samples is due to squirt‐flow of fluid between the pores of various geometries. The contribution of the Biot‐flow loss mechanism to the total loss is negligible. The compressional‐wave quality factor was shown to be inversely correlated with rock permeability, suggesting the possibility of using attenuation as a permeability indicator tool in low‐shale, high‐porosity sandstone reservoirs.     

Ultrasonic measurements of Vp and Qp: relaxation spectrum of complex modulus on basalt melts

Ultrasonic compressional wave velocity V_p and quality factor Q_p have been measured in alkali basalt, olivine basalt and basic andesite melts in the frequency range of 3.4–22 MHz and in the temperature range of 1100–1400°C. Velocity and attenuation of the melts depend on frequency and temperature, showing that there are relaxation mechanisms in the melts. Complex moduli are calculated from the ultrasonic data. The results fit well a complex modulus of Arrhenius temperature dependence with log-normal Gaussian distribution in relaxation times of attenuation. The analysis yields average relaxation time, its activation energy, relaxed modulus, unrelaxed modulus and width of Gaussian distribution in relaxation times. Relaxed modulus is smaller (17.5 GPa) for basic andesite melt of high silica and high alumina contents than for the other two basalt melts (18.1–18.4 GPa). The most probable relaxation times decrease from ～ 3 × 10^?10 s for basic andesite to ～ 10^?11 s for alkali basalt at 1400°C. Activation energies of attenuation, ranging from 270 to 340 kJ mol^?1 in the three melts, are highest in basic andesite. Longitudinal viscosity values and their temperature dependences are also calculated from V_p and Q_p data. The volume viscosity values are estimated from the data using the shear viscosity values. Longitudinal, volume and shear viscosities and their activation energies are highest in the basic andesite melt of the most polymerized structure.     

SEISMIC AND ELECTRICAL PROPERTIES OF UNCONSOLIDATED PERMAFROST1

A model has been developed to relate the velocities of acoustic waves V_p and V_s in unconsolidated permafrost to the porosity and extent of freezing of the interstitial water. The permafrost is idealized as an assemblage of spherical quartz grains embedded in a matrix composed of spherical inclusions of water in ice. The wave-scattering theory of Kuster and Toksoz is used to determine the effective elastic moduli, and hence the acoustic velocities. The model predicts V_p and V_s to be decreasing functions of both the porosity and the water-to-ice ratio. The theory has been applied to laboratory measurements of V_p and V_s in 31 permafrost samples from the North American Arctic. Although no direct measurements were made of the extent of freezing in these samples, the data are consistent with the predictions of the model. Electrical resistivity measurements on the permafrost samples have demonstrated their essentially resistive behaviour. The ratio of resistivity of permafrost in its frozen state to that in its unfrozen state has been related to the extent of freezing in the samples. Electromagnetic and seismic reflection surveys can be used together in areas of permafrost: firstly an EM survey to determine the extent of freezing and then the acoustic velocity model to predict the velocities in the permafrost. The necessary transit time corrections can thus be made on seismic reflection records to compensate for the presence of permafrost.     

COMMON REFLECTION POINT DATA-STACKING TECHNIQUE FOR CONVERTED WAVES1

For converted waves stacking requires a true common reflection point gather which, in this case, is also a common conversion point (CCP) gather. We consider converted waves of the PS- and SP-type in a stack of horizontal layers. The coordinates of the conversion points for waves of PS- or SP-type, respectively, in a single homogeneous layer are calculated as a function of the offset, the reflector depth and the velocity ratio v_p/v_s. Knowledge of the conversion points enables us to gather the seismic traces in a common conversion point (CCP) record. Numerical tests show that the CCP coordinates in a multilayered medium can be approximated by the equations given for a single layer. In practical applications, an a priori estimate of v_p/v_s is required to obtain the CCP for a given reflector depth. A series expansion for the traveltime of converted waves as a function of the offset is presented. Numerical examples have been calculated for several truncations. For small offsets, a hyperbolic approximation can be used. For this, the rms velocity of converted waves is defined. A Dix-type formula, relating the product of the interval velocities of compressional and shear waves to the rms velocity of the converted waves, is presented.     

Estimation of Q p and Q s of Kinnaur Himalaya

The attenuation characteristics of the Kinnaur area of the North West Himalayas were studied using local earthquakes that occurred during 2008–2009. Most of the analyzed events are from the vicinity of the Panjal Thrust (PT) and South Tibetan Detachment Thrust, which are well-defined tectonic discontinuities in the Himalayas. The frequency-dependent attenuation of P and S waves was estimated using the extended coda normalization method. Data from 64 local earthquakes recorded at 10 broadband stations were used. The coda normalization of the spectral amplitudes of P and S waves was done at central frequencies of 1.5, 3, 6, 9, and 12 Hz. Q _p increases from about 58 at 1.5 Hz to 706 at 12 Hz, and Q _s increases from 105 at 1.5 Hz to 1,207 at 12 Hz. The results show that the quality factors for both P and S waves (Q _p and Q _s) increase as a function of frequency according to the relation Q?=?Q _o f ⁿ , where Q _o is the corresponding Q value at 1 Hz frequency and “n” is the frequency relation parameter. We obtained Q _p?=?(47?±?2)f ^(1.04±0.04) and Q _s?=?(86?±?4)f ^(0.96±0.03) by fitting power law dependency model for the estimated values of the entire study region. The Q ₀ and n values show that the region is seismically very active and the crust is highly heterogeneous. There was no systematic variation of values of Q _p and Q _s at different frequencies from one tectonic unit to another. As a consequence, average values of these parameters were obtained for each frequency for the entire region, and these were used for interpretation and for comparison with worldwide data. Q _p values lie within the range of values observed for some tectonically active regions of the world, whereas Q _s values were the lowest among the values compared for different parts of the world. Q _s/Q _p values were >1 for the entire range of frequencies studied. All these factors indicate that the crust is highly heterogeneous in the study region. The high Q _s/Q _p values also indicate that the region is partially saturated with fluids.     

Time domain solution for multiple scattering and the coda envelopes

This article summarizes work on multiple scattering based on models of media with randomly distributed scatterers. The scatterers are isotropic and statistically uniform. Measuring distance in terms of mean-free pathL _s and time in terms of the mean-free timesL _s/V, whereV is the velocity of scattered waves, we have more convenient dimensionless distance and time. It can be shown that after the dimensionless time equals 0.65 energy contributed from multiple scattering becomes predominant. Thus the later coda reflects the effect of multiple scattering rather than single scattering. Treating the seismic record, including starting and tail parts, as a whole, the diffusion theory predicts that at a dense distribution of scatterers and a small distance between source and receiver, codas reflect mainly intrinsicQ _i. Of course, this conclusion is coincident with the presumption of the diffusion theory,Q _s>Q _i. However, from a new integral equation of multiple scattering, which deals with the scattered waves and primary waves separately, the conclusion is similar but clearer. This article quotes the new expression for coda energy in two-dimensional space. It shows that if the receiver is close to the source, the coda decay reflects only intrinsicQ _i, then as the distance increases, effects of scatteringQ _s, are involved in the decay feature. The theoretical plots of coda decay show that it seems in most cases in the earthQ _i should not be smaller than one tenth ofQ _s.Project Sponsored by the Joint Earthquake Science Foundation of China.     

τ-p SEISMIC DATA FOR VISCOELASTIC MEDIA - PART 2: LINEARIZED INVERSION1

An approach to extraction of viscoelastic parameters from seismic data is implemented and succesfully tested. Viscoelastic inversion is performed using adaptive damping factors to control the sensitivity of the viscoelastic parameters in relation to the τ-p seismic data. A priori information is incorporated through the damping factors as standard deviations of the data and of the viscoelastic model parameters. The stability of the inversion process is controlled by the variation of the damping factors as a function of the residual errors and parameter updates at each iteration. Tests on synthetic and real data show that P- and S-wave quality factors, Q_p and Q_s, in addition to P- and S-wave velocities and density C_p, C_s and p, can be extracted from τ-p seismic information. Singular value decomposition analysis demonstrates that estimated Q_p and Q_s values are more affected by the presence of data inaccuracies and noise than are those of C_p and p. C_s and Q_s are not uniquely recovered due to the limited contribution of P-S converted waves. Knowledge of the viscoelastic parameters is of particular importance in accurately describing petrophysical properties of rocks and pore fluids existing in the subsurface; this is demonstrated with real data from the Gulf of Mexico.     

Lithology and hydrocarbon mapping from multicomponent seismic data

Elastic rock properties can be estimated from prestack seismic data using amplitude variation with offset analysis. P‐wave, S‐wave and density ‘reflectivities’, or contrasts, can be inverted from angle‐band stacks. The ‘reflectivities’ are then inverted to absolute acoustic impedance, shear impedance and density. These rock properties can be used to map reservoir parameters through all stages of field development and production. When P‐wave contrast is small, or gas clouds obscure reservoir zones, multicomponent ocean‐bottom recording of converted‐waves (P to S or Ps) data provides reliable mapping of reservoir boundaries. Angle‐band stacks of multicomponent P‐wave (Pz) and Ps data can also be inverted jointly. In this paper Aki‐Richards equations are used without simplifications to invert angle‐band stacks to ‘reflectivities’. This enables the use of reflection seismic data beyond 30° of incident angles compared to the conventional amplitude variation with offset analysis. It, in turn, provides better shear impedance and density estimates. An important input to amplitude variation with offset analysis is the V_s/V_p ratio. Conventional methods use a constant or a time‐varying V_s/V_p model. Here, a time‐ and space‐varying model is used during the computation of the ‘reflectivities’. The V_s/V_p model is generated using well log data and picked horizons. For multicomponent data applications, the latter model can also be generated from processing V_s/V_p models and available well data. Reservoir rock properties such as λρ, μρ, Poisson's ratio and bulk modulus can be computed from acoustic impedance, shear impedance and density for pore fill and lithology identification. λ and μ are the Lamé constants and ρ is density. These estimations can also be used for a more efficient log property mapping. V_p/V_s ratio or Poisson's ratio, λρ and weighted stacks, such as the one computed from λρ and λ/μ, are good gas/oil and oil/water contact indicators, i.e., pore fill indicators, while μρ mainly indicates lithology. μρ is also affected by pressure changes. Results from a multicomponent data set are used to illustrate mapping of gas, oil and water saturation and lithology in a Tertiary sand/shale setting. Whilst initial log crossplot analysis suggested that pore fill discrimination may be possible, the inversion was not successful in revealing fluid effects. However, rock properties computed from acoustic impedance, shear impedance and density estimates provided good lithology indicators; pore fill identification was less successful. Neural network analysis using computed rock properties provided good indication of sand/shale distribution away from the existing wells and complemented the results depicted from individual rock property inversions.