共查询到20条相似文献,搜索用时 478 毫秒
1.
In marine cycloidal propeller (MCP), the inflow velocity vector to the propeller blade continuously changes at different blade orbit angle. Earlier marine cycloidal propellers were installed on ships that mainly performed towing operations. Recently marine cycloidal propellers are being installed on large naval vessels, which spend lot of their operating hours in cruising. Therefore, the hydrodynamic loading on the blades both during cruising maneuvers need to be investigated. The flow characteristics around the propeller blade are computed numerically by panel method. Viscous effects on the flow are then estimated by boundary layer technique. The effect of rotating disc on viscous fluid is also investigated. The corrected flow characteristics are then used for estimating the hydrodynamic loading. The operating conditions that are critical for the loading of the blade and the support structure and some aspects of the maneuvering simulation at cruising speed are investigated. 相似文献
2.
The purpose of this paper is to optimise the hydroelastic performance of a composite marine propeller to reduce vibration and dynamic stress. A hydroelasticity method based on the finite element method (FEM) coupled with computational fluid dynamics (CFD) is used to simulate the composite marine propeller in a non-uniform wake. Composite blades can be considered as a cantilever-like laminated structure experiencing an unsteady hydrodynamic load and centrifugal force. The objective of the improved design is to minimise the vibratory hub loads. The ply angle and stacking sequence are considered as the design variables. The nonlinear periodic transient responses and vibration hub loads of the composite blade are obtained by solving coupled equations using the Newton–Raphson numerical procedure. Compared to the starting design of the propeller, the optimum solution results in a 49.6–70.6% reduction of the 7/rev hub loads. 相似文献
3.
In this paper, the flow-induced vibrations of marine propellers in cyclic inflows are investigated both experimentally and numerically. A Laser-Doppler velocimetry (LDV) system is used to measure the axial flow velocity distributions produced by the seven-cycle wake screen in the water tunnel. A customized underwater slip ring and a single axis accelerometer sealed by silicon sealant are employed to measure the acceleration responses of rotating propeller blade. Numerical simulations of pressure fluctuations on the blades are performed using large eddy simulation (LES), while the forced vibrations of the propeller blades are obtained by a combined finite element and boundary element method. Experimental and numerical results are presented for two model propellers with the same geometries and different flexible properties, which show that the propeller blade vibrates at a frequency which is seven times as large as the axial passing frequency (APF) in the seven-cycle inflow. Moreover, the propeller blades are observed to resonance when the 7 APF excitation frequency is equal to the fundamental frequency of the propellers. The results indicate that both the inflow feature and the modal characteristic of blades contribute to flow-induced vibrations of elastic propellers. 相似文献
4.
The hydrodynamic characteristics of a marine propeller operating in oblique inflow are investigated by using CFD method. Two propellers with different geometries are selected as the study subjects. RANS simulation is carried out for the propellers working at a wide range of advance coefficients and incidence angles. The effects of axial inflow and lateral inflow are demonstrated with the hydrodynamic force on the propeller under different working conditions. Based on the obtained flow field details, the hydrodynamic mechanism of propeller operating in oblique inflow is analyzed further. The trailing vortex wake of propeller is highly affected by the lateral inflow, resulting in the deflected development path and the circumferentially non-uniform structure, as well as the enhanced axial velocity in slipstream. Different flow patterns are observed on the propeller blade with the variation of circumferential position. Combined with the computed hydrodynamic forces and pressure distribution on propeller, the mechanism resulting in the increase of propulsive loads and the generation of propeller side force is explored. Finally, a systematic analysis is carried out for the propulsive loads and propeller side force as a function of axial and lateral advance coefficients. The major terms that play a dominant role in the modeling of propulsive loads and propeller side force are determined through the sensitivity analysis. This study provides a deeper insight into the hydrodynamic characteristics of propeller operating in oblique inflow, which is useful to the investigation of propeller performance during ship maneuvers. 相似文献
5.
During ice-breaking navigation, a massive amount of crushed ice blocks with different sizes is accumulated under the hull of an ice-going ship. This ice slides into the flow field in the forward side of the podded propulsor, affecting the surrounding flow field and aggravating the non-uniformity of the propeller wake. A pulsating load is formed on the propeller, which affects the hydrodynamic performance of the podded propulsor. To study the changes in the propeller hydrodynamic performance during the ice podded propulsor interaction, the overlapping grid technique is used to simulate the unsteady hydrodynamic performance of the podded propulsor at different propeller rotation angles and different ice block sizes. Hence, the hydrodynamic blade behavior during propeller rotation under the interaction between the ice and podded propulsor is discussed. The unsteady propeller loads and surrounding flow fields obtained for ice blocks with different sizes interacting with the podded propulsor are analyzed in detail. The variation in the hydrodynamic performance during the circular motion of a propeller and the influence of ice size variation on the propeller thrust and torque are determined. The calculation results have certain reference significance for experiment-based research, theoretical calculations and numerical simulation concerning ice podded propulsor interaction. 相似文献
6.
基于重叠网格模型,通过非定常RANS数值模拟与结果分析,研究了块状冰的尺寸、轴向运动和冰桨位置对螺旋桨水动力性能的影响。选用切割体网格绘制整体静止计算域的背景网格,之后结合棱柱层网格绘制螺旋桨子计算域和冰块子计算域的重叠网格,不同的计算域之间通过两者的重叠区域进行数据传递和插值。计算结果显示,当冰块固定在桨前时,螺旋桨产生的非定常推力和扭矩均以叶频为基频进行周期性变化,而且两者的时间平均值和振幅主要受冰块在螺旋桨盘面内的轴向投影面积、冰桨轴向位置和冰桨水平位置的影响;当冰块在桨前沿轴向匀速靠近螺旋桨时,冰桨轴向距离逐渐变小,冰桨周向相对位置发生周期性的变化,使得推力和扭矩两者均以叶频振荡,而且两者的时间平均值和振幅均随着冰桨轴向距离减小而增加。 相似文献
7.
Surface Piercing Propellers (SPPs) are a particular kind of propellers which are partially submerged operating at the interface of air and water. They are more efficient than submerged propellers for the propulsion system of high-speed crafts because of larger propeller diameter, replacing cavitation with ventilation, decreasing the torque and higher efficiency. This study presents a reliable numerical simulation to predict SPP performance using Unsteady Reynolds-Averaged Navier–Stokes (URANS) method. A numerical study on 841-B SPP is performed in open water condition. The free surface is modeled by Volume of Fluid (VOF) approach and the sliding mesh technique is implemented to model the propeller rotational motion. The sliding mesh allows capturing the process of water entry and water exit of blades. The propeller hydrodynamic characteristics, the ventilation pattern and the time history of blade loads are validated through the comparison with available experimental data. For the studied case, it was found that the common grid independence study approach is not sufficient. The grid should be elaborately generated fine enough based on the flow pattern and turbulence modeling parameters in regions near the blade's tip, trailing and leading edges and over the suction side. Details of URANS simulations including optimal time-step size based on propeller revolution rate and the required number of propeller revolutions for periodical results are presented and discussed. 相似文献
8.
The blade frequency noise of non-cavitation propeller in a uniform flow is analyzed in time domain. The unsteady loading (dipole source) on the blade surface is calculated by a potential-based surface panel method. Then the time- dependent pressure data is used as the input for Ffowcs Williams-Hawkings formulation to predict the acoustics pressure. The integration of noise source is performed over the true blade surface rather than the nothickness blade surface, and the effect of hub can be considered. The noise characteristics of the non-cavitation propeller and the numerical discretization forms are discussed. 相似文献
9.
The understanding and the accurate assessment of propeller loads in realistic operative scenario, both design and off-design conditions, is of paramount importance to design low emission and comfortable ships, fulfilling the requirements of structural integrity of the propulsion system, safety and continuity of operations at sea. To this purpose, a deeper characterization of the propeller functioning, in terms of averaged and fluctuating loads, can be attained by means of the quantification of the single blade loads. In this work, a novel set up that allows to monitor the loads developed by a single blade was implemented on a free running, self propelled maneuvering model with the aim to investigate in details the hydrodynamic interactions between the spatially non-homogeneous and time-variant wake of the hull and the propeller and a complete characterization of its performance. This preliminary work introduces the experimental setup and provides a preliminary overview of the results relative to straight ahead motion. 相似文献
10.
The blade frequency noise of non-cavitation propeller in a uniform flow is analyzed in time domain. The unsteady loading (dipole source) on the blade surface is calculated by a potential-based surface panel method. Then the time- dependent pressure data is used as the input for Ffowcs Williams-Hawkings formulation to predict the acoustics pressure. The integration of noise source is performed over the true blade surface rather than the nothickness blade surface, and the effect of hub can be considered. The ... 相似文献
11.
Surface-Piercing Propellers (SPPs) are the preferred propulsion system for light to moderately loaded high-speed applications due to the high fuel efficiency. For highly loaded applications, the efficiency of SPPs tends to decrease because of the limited submerged blade area and the presence of large suction side cavities. Moreover, it is a challenge to design large-scale SPPs that can maintain reliable fatigue strength and avoid vibration issues while maximizing the propeller thrust for a given power input. In this work, three SPP designs are presented for different size Surface Effect Ships (SESs) that can attain a maximum advance speed of 25.72 m/s (50 knots). A previously developed and validated three-dimensional (3-D) coupled boundary element method-finite element method (BEM-FEM) is used for the transient hydroelastic analysis of SPPs. The method is validated by comparing the predicted hydrodynamic performance with those obtained using a vortex-lattice method (VLM) and a Reynolds Averaged Navier-Stokes (RANS) solver. The hydrodynamic and structural dynamic performance of the SPPs are presented. Finally, challenges associated with the design related analyzes of large-scale SPPs are discussed. 相似文献
12.
In the present study, cavitation and a ship propeller wake are reported by computed fluid dynamics based on viscous multiphase flow theory. Some recent validation results with a hybrid grid based on unsteady Navier-Stokes (N-S) and bubble dynamics equations are presented to predict velocity, pressure and vapor volume fraction in propeller wake in a uniform inflow. Numerical predictions of sheet cavitation, tip vortex cavitation and hub vortex cavitation are in agreement with the experimental data, same as numerical predictions of longitudinal and transversal evolution of the axial velocity. Blade and shaft rate frequency of propeller is well predicted by the computed results of pressure, and tip vortex is the most important to generate the pressure field within the near wake. The overall results indicate that the present approach is reliable for prediction of cavitation and propeller wake on the condition of uniform inflow. 相似文献
13.
《中国海洋工程》2020,(3)
The research on the hydrodynamics of blades is mainly focused on sea areas with high-speed current. However, the average velocity in most territorial waters of China is smaller than 1 m/s, and the lift type of airfoil blades has limited application in most of these conditions. Therefore, it is of great significance to study the tidal current energy capture of blades in sub-low speed sea areas. The effect of flow impact resistance on the blade at sub-low current speed is considered and a new type of thin-walled blade based on the lift type of blade is proposed, and then the lift-impact combined hydrodynamic model of horizontal axis blade is established. Based on this model, and considering the characteristics of tidal current and velocity in the sea area of Yushan Islands, simulation and optimization of blade design are carried out. Additionally, the horizontal axis thin-walled blade and the NACA airfoil contrast blade under the same conditions are developed. By using a synthetical experimental test system, the power, torque, rotational speed and load characteristics of these two blades are tested. The performance of the thin-walled blade and the design theory are verified. It shows that this type of blade has much better energy capture efficiency in the sub-low speed sea area. This research will promote the study and development of turbines that can be used in low-speed current sea areas in the future. 相似文献
14.
This paper presents the results of a numerical performance analysis to demonstrate the worthiness of a recently patented new concept propulsor, the so-called “thrust-balanced propeller (TBP)”. The main advantage of this unconventional propulsor is its inherent ability to reduce the unsteady effect of blade forces and moments when it is operating in a non-uniform wake flow. The propulsor comprises a pair of diametrically opposed blades that are connected to one another and mounted so as to be rotatable together through a limited angle about their spindle axis. A quasi-hydrodynamic approach is described and applied to perform the numerical analysis using a state-of-the-art lifting surface procedure for conventional propellers. Performance comparisons with a conventional fixed-pitch propeller are made for the blade forces and moments, efficiency, cavitation extents and fluctuating hull pressures. Bearing in mind the quasi-static nature of the analyses, the results present favourable performance characteristics for the thrust-balanced propeller and support the worthiness of the concept. However, the concept needs to be proved through physical model tests, which are planned to take in a cavitation tunnel. 相似文献
15.
The existing propulsor that can perform both propulsion and maneuvering along axis of rotation is propeller/rotor for a helicopter. Helicopter propellers when maneuvering increase or decrease their blades’ pitch cyclically to create imbalanced thrust and hence maneuvering force/torque. A “maneuverable propeller” was developed and its performance on both maneuvering and propulsion is assessed. The “maneuverable propeller” is an alternative of the existing helicopter rotors. The novelty of this propulsor is that the imbalanced thrust force/torque is created by cyclically increasing or decreasing the angular speed of their blades relatively to the hubs/shafts, to provide the desired maneuvering torque. This maneuverable propeller is hence defined as the Cyclic Blade Variable Rotational Speed Propeller (CBVRP). One of the best advantages is that the maneuvering torque created by the “maneuverable propeller” is much higher, about 5 times of the shaft torque of the same propeller at thrust only mode. The “maneuverable propeller” has wide applications for both surface ships and underwater vehicles that require high maneuverability for cruising inside the narrow passage. 相似文献
16.
Flow characteristics of the hull wake behind a container ship model were investigated under different loading conditions (design and ballast loadings) by employing the particle image velocimetry (PIV) technique. Measurements were made at four transverse locations and two longitudinal planes for three Reynolds numbers (Re) (=U0Lpp/ν, where U0 is the freestream velocity, Lpp is the length between two perpendiculars of the ship model and ν is the kinematic viscosity) of 5.08×105, 7.60×105, and 1.01×106. It was observed that symmetric, large-scale, longitudinal counter-rotating vortices (with respect to centerline) of nearly the same strength were formed in the near wake. For the ballast-loading condition, the vortices appear at propeller plane below the propeller-boss. The vortex center exhibits a significant upward shift near the propeller-boss as the Reynolds number increase, and as the flow moves downstream. Under the design-loading condition, the vortices first appear at a further downstream location than that for the ballast-loading condition above the propeller-boss. This difference in the flow structure can significantly change the inflow conditions to the propeller blades, such as the streamwise mean velocity profiles and turbulence intensity distributions at the propeller plane. In particular, under the ballast-loading condition, asymmetric inflow may weaken the propulsion and cavitation performance of the marine propeller. 相似文献
17.
The Computational Fluid Dynamics (CFD) approach is adopted to study the steady and unsteady performances of the podded propulsor by the Fluent software package. While the interactions of the propeller blades with the pod and strut are time-dependent by nature, the mixing plane model is employed firstly to predict the steady performance, where the interactions are time-averaged. Numerical experiments are carried out with systematically varied mesh sizes to investigate the dependence of the predicted force values on the mesh sizes. Furthermore, the sliding mesh model is employed to simulate the unsteady interactions between the blades, pod and strut. Based on the numerical results, the characteristics of unsteady hydrodynamic forces are discussed, and the applicability of the mixing plane model is investigated for puller-type podded propulsor. 相似文献
18.
Marine propellers usually operate in a spatially nonuniform wake and then the propeller exciting forces are produced. These exciting forces will cause serious hull vibration and noise radiation. So, there are many researches on the exciting forces of propellers. However, the effects of the shaft and blade elasticity are ignored in most studies. Therefore, firstly, considered the effects of the shaft and blade elasticity, a fluid–structure interaction dynamic model of the fluid-propeller-shaft system is established by coupled BEM and FEM. Then, based on this model, the characteristics of axial exciting force and theirs transmission mechanism to the hull via the shaft are studied. The research results show that first, there are two kinds of vibration modes for blade bending vibration: global mode and local mode. The elastic coupling effect between the blade and the shafting only affects the global mode, but hardly affects the local mode of the blade. Secondly, during the transmission of axial exciting force to the hull through the blades and shafting, only the global mode of the blades can amplify it, while the local mode cannot. These studies could provide a guideline for the optimal design of the propeller-shaft system to make the exciting force transmitted to the ship hull via the shafting be the smallest. 相似文献
19.
导管桨的尾流不稳定性在其性能评价中非常重要,不但是其能否提供稳定推力的保证,而且也与螺旋桨的尾流噪声直接相关。为了改善导管桨的尾流,提高尾流稳定性,并优化导管桨的流场脉动,根据座头鲸鳍肢前缘结节的仿生原理,对导管桨叶片的导边进行改进,提出了两种仿生桨型,采用IDDES湍流模型对低进速系数下常规导管桨和仿生叶片导管桨进行数值模拟,探究叶片构型对导管桨性能和尾流不稳定性的影响。计算结果表明,前缘结节可以有效降低叶片受力波动的幅值和叶片所受合力的主频域峰值,具有较大结节的叶片对导管桨尾流有明显的优化作用,在尾流远场中扩大了流动稳定区,延后了尾流处涡破碎的发生,改善了能量谱密度的频域分布。进一步,大前缘结节叶片导管桨应用在低速工况下时,可以大量减少尾流泄涡区域的二次涡产生,这是由于前缘结节提升了相邻涡互感的强度,使得尾流更加稳定,而小结节叶片仿生桨型对导管桨尾流则无明显优化作用。研究方法和成果可为螺旋桨尤其是导管桨尾流不稳定性研究提供参考,不仅验证了前缘结节在导管桨叶片应用的合理性,而且揭示了其优化尾流稳定性的机理。 相似文献
20.
在开放海域运行的潮流能水轮机需要应对复杂多变的海洋环境,要有较好的刚度、强度和抗疲劳性能。这对水轮机结构,尤其是为其运行提供动力的叶片结构的设计提出了较高要求。文中建立了垂直轴潮流能水轮机叶片及流场的三维数值计算模型,基于ANSYS商业软件提供的CFX与瞬时结构模块的双向流固耦合分析功能,分析了叶片在不同流速下的流体力学性能,分析了流场的三维效应及其引起叶片升力损失的原因,研究了其结构的刚度和强度特性。还对比分析了使用铝合金和钢材作为水轮机叶片材料的优劣。 相似文献