Sheet flow hydrodynamics over a non-uniform sand bed channel

The current study experimentally investigates the flow characteristics and temporal variations in the sheet flow profile of a non-uniform sand bed channel. Experiments were done to explore turbulent structures in the presence of a sheet flow layer with and without seepage. The turbulent events, such as stream wise velocity, Reynolds shear stresses, and turbulence intensities were found to be increasing and vertical velocity was found decreasing with a sheet layer. The presence of a sheet layer also effects the turbulent energy production and energy dissipation. All the turbulence parameters with and without a sheet layer have also been influenced by the presence of downward seepage. The rate of sheet flow movement is increased with seepage, owing to increased turbulence with seepage. The current study used wavelet analysis on temporally lagged spatial bed elevation profiles obtained from a set of laboratory experiments and synchronized the wavelet coefficients with bed elevation fluctuation at different spatial scales. A spatial cross correlation analysis at multiple scales, based on the wavelet coefficients, has been done on these bed elevation datasets to observe the effect of downward seepage on the dynamic behavior of sheet flow at different length scales. It is found that seepage increases average bed celerity and also increases the celerity of sheet flow of similar length scales. This increase in the celerity has been hypothesized as the increase of sheet flow movement as well as the increase in turbulent parameters with seepage, which destabilizes the bed particles resulting in a disruption in the continuous propagation pattern of the sheet flow. The increase of sheet flow celerity with seepage is confirmed from the saturation level of the wavelet power spectra of the bed elevation series. The presence of seepage also affects the non-uniformity of collective sheet material.     

Bedform effect on the reorganization of surface and subsurface grain size distribution in gravel bedded channels

Quantification of river bedform variability and complexity is important for sediment transport modeling as well as for characterization of river morphology. Alluvial bedforms are shown to exhibit highly nonlinear dynamics across a range of scales, affect local bed roughness, and vary with local hydraulic, hydrologic, and geomorphic properties. This paper examines sediment sorting on the crest and trough of gravel bedforms and relates it to bed elevation statistics. The data analysed here are the spatial and temporal series of bed elevation, grain size distribution of surface and subsurface bed materials, and sediment transport rates from flume experiments. We describe surface topography through bedform variability in height and wavelength and multiscale analysis of bed elevations as a function of discharge. We further relate bedform migration to preferential distribution of coarse and fine sediments on the troughs and crests, respectively, measuring directly surface and subsurface grain size distributions, and indirectly the small scale roughness variations as estimated from high resolution topographic scans.     

Sand settling through bedform-generated turbulence in rivers

Fluvial bedforms generate a turbulent wake that can impact suspended-sediment settling in the passing flow. This impact has implications for local suspended-sediment transport, bedform stability, and channel evolution; however, it is typically not well-considered in geomorphologic models. Our study uses a three-dimensional OpenFOAM hydrodynamic and particle-tracking model to investigate how turbulence generated from bedforms and the channel bed influences medium sand-sized particle settling, in terms of the distribution of suspended particles within the flow field and particle-settling velocities. The model resolved the effect of an engineered bedform, which altered the flow field in a manner similar to a natural dune. The modelling scenarios alternated bed morphology and the simulation of turbulence, using detached eddy simulation (DES), to differentiate the influence of bedform-generated turbulence relative to that of turbulence generated from the channel bed. The bedform generated a turbulent wake that was composed of eddies with significant anisotropic properties. The eddies and, to a lesser degree, turbulence arising from velocity shear at the bed substantially reduced settling velocities relative to the settling velocities predicted in the absence of turbulence. The eddies tended to advect sediment particles in their primary direction, diffuse particles throughout the flow column, and reduced settling likely due to production of a positively skewed vertical-velocity fluctuation distribution. Study results suggest that the bedform wake has a significant impact on particle-settling behaviour (up to a 50% reduction in settling velocity) at a scale capable of modulating local suspended transport rates and bedform dynamics. © 2020 John Wiley & Sons, Ltd.     

Detailed bed topography and sediment load measurements for two stepdown flows in a laboratory flume

Streams and rivers, particularly smaller ones, often do not maintain steady flow rates for long enough to reach equilibrium conditions for sediment transport and bed topography. In particular, streams in small watersheds may be subject to rapidly changing hydrographs, and relict bedforms from previous high flows can cause further disequilibrium that complicates the prediction of sediment transport rates. In order to advance the understanding of how bedforms respond to rapid changes in flow rate,...     

Velocity characteristics along a small step–pool channel

This paper summarizes measurements of velocity along three reaches of a small mountain channel with step–pool bedforms. A one‐dimensional electromagnetic current meter was used to record velocity fluctuations at 37 fixed measurement points during five measurement intervals spanning the peak of the annual snowmelt hydrograph. Measurement cross‐sections were located upstream from a bed‐step, at the step lip, downstream from the step, and in a uniform‐gradient run. Data analyses focused on characteristics of velocity profiles, and on correlations between velocity characteristics and the potential control variables bedform type, reach gradient and flow depth. To test the hypothesis that velocity characteristics are related to channel bedform types, ANOVA and ANCOVA tests were performed for the average velocity and coefficient of variation of point velocity data. Results indicate that high frequency velocity variations correlate to some degree with both channel characteristics and discharge. Velocity became more variable as stage increased, particularly at low‐gradient reaches with less variable bed roughness. Velocity profiles suggest that locations immediately downstream from bed‐steps are dominated by wake turbulence from mid‐profile shear layers. Locations immediately upstream from steps, at step lips, and in runs are dominated by bed‐generated turbulence. Adverse pressure gradients upstream and downstream from steps may be enhancing turbulence generation, whereas favourable pressure gradients at steps are suppressing turbulence. The bed‐generated turbulence and skin friction of runs appear to be less effective energy dissipators than the wake‐generated turbulence and form drag of step–pool bedforms. Copyright © 2000 John Wiley & Sons, Ltd.     

Topographic forcing of flow partition and flow structures at river bifurcations

This paper presents the predicted flow dynamics from the application of a Reynolds‐averaged Navier–Stokes model to a series of bifurcation geometries with morphologies measured during previous flume experiments. The topography of the bifurcations consists of either plane or bedform‐dominated beds which may or may not possess discordance between the two bifurcation distributaries. Numerical predictions are compared with experimental results to assess the ability of the numerical model to reproduce the division of flow into the bifurcation distributaries. The hydrodynamic model predicts: (1) diverting fluxes in the upstream channel which direct water into the distributaries; (2) super‐elevation of the free surface induced at the bifurcation edge by pressure differences; and (3) counter‐rotating secondary circulation cells which develop upstream of the apex of the bifurcation and move into the downstream channels, with water converging at the surface and diverging at the bed. When bedforms are not present, weak transversal fluxes characterize the upstream channel for almost its entire length, associated with clearly distinguishable secondary circulation cells, although these may be under‐estimated by the turbulence model used in the solution. In the bedform dominated case, the same hydrodynamic conditions were not observed, with the bifurcation influence restricted and depth scale secondary circulation cells not forming. The results also demonstrate the dominant effect bed discordance has upon flow division between the two distributaries. Finally, results indicate that in bedform dominated rivers. Consequently, we suggest that sand‐bed river bifurcations are more likely to have an influence that extends much further upstream and have a greater impact upon water distribution. This may contribute to observed morphological differences between sand‐bedded and gravel‐bedded braided river networks. Copyright © 2012 John Wiley & Sons, Ltd.     

How does the bed surface impact low-magnitude bedload transport rates over gravel-bed rivers?

Bedload transport is a complex phenomenon that is not well understood, especially for poorly sorted sediment and low transport rates, which is what is typically found in alpine gravel-bed rivers. In this paper, the interaction between bedload rate, bed stability and flow is investigated using flume experiments. Significant differences in bedload rates were observed for experiments conducted on beds formed with the same gravel material but presenting diverse arrangements and bedforms. Tests were performed under regimes of low transport rate, which are mainly controlled by gravel-bed roughness. Different scales of roughness were identified using the statistical characteristics of detailed bed elevation measurements: grain, structure and large bedform scales. The role played by these different roughness scales in bedload dynamics was examined. For quasi-flat beds, bed stability was quantified using a combination of bed surface criteria describing grain and structure scales. It was found that bed stability affects the bedload rate directly and not only through its influence on the flow or on the incipient motion. For beds with large bedforms, the analysis of bedload dynamics also showed the importance of accounting for effective bed shear stress distributions. An empirical bedload model for low transport regimes was suggested. Compared with previous formulae developed for alpine rivers, this model accounts for bed stability and distribution of effective bed shear stress. It significantly improves the understanding of gravel dynamics over complex beds such as arranged beds or those with large bedforms. However, further tests are needed to use the model outside the range of conditions of this study. © 2019 John Wiley & Sons, Ltd.     

Riffle‐pool morphometry and stage‐dependant morphodynamics of a large floodplain river (Vereinigte Mulde,Sachsen‐Anhalt,Germany)

Riffle‐pool sequences are a common feature of gravel‐bed rivers. However, mechanisms of their generation and maintenance are still not fully understood. In this study a monitoring approach is employed that focuses on analysing cross‐sectional and longitudinal channel geometry of a large floodplain river (Vereinigte Mulde, Sachsen‐Anhalt, Germany) with a high temporal and spatial resolution, in order to conclude from stage‐dependant morphometric changes to riffle and pool maintaining processes. In accordance with previous authors, pool cross‐sections of the Mulde River are narrow and riffle cross‐sections are wide suggesting that they should rather be addressed as two general types of channel cross‐sections than solely as bedforms. At high flows, riffles and pools in the study reaches changed in length and height but not in position. Pools were scoured and riffles aggraded, a development which was reversed during receding flows below the threshold of 0·4Q_bf (40% bankfull discharge). An index for the longitudinal amplitude of riffle‐pool sequences, the bed undulation intensity or bedform amplitude, is introduced and proved to be highly significant as a form parameter, its first derivative as a process parameter. The process of pool scour and riffle fill is addressed as bedform maintenance or bedform accentuation. It is indicated by increasing longitudinal bed amplitudes. According to the observed dynamics of bed amplitudes, maintenance of riffle‐pool sequences lags behind discharge peaks. Maximum bed amplitudes may be reached with a delay of several days after peak discharges. Increasing bed undulation intensity is interpreted to indicate bed mobility. Post‐flood decrease of the bed undulation intensity indicates a retrograde phase when transport from pools to riffles has ceased and bed mobility is restricted to riffle tails and heads of pools. This type of transport behaviour is referred to as disconnected mobility. The comparison of two river reaches, one with undisturbed sediment supply, the other with sediment deficit, suggests that high bed undulation intensity values at low flows indicate sediment deficit and potentially channel degrading conditions. It is more generally hypothesized that channel bed undulations constitute a major component of form roughness and that increased bed amplitudes are an important feature of channel bed adjustment to sediment deficit be it temporally during late floods or permanently due to a supply limitation of bedload. Copyright © 2011 John Wiley & Sons, Ltd.     

Bedform response to flow variability

Laboratory observations and computational results for the response of bedform fields to rapid variations in discharge are compared and discussed. The simple case considered here begins with a relatively low discharge over a flat bed on which bedforms are initiated, followed by a short high‐flow period with double the original discharge, during which the morphology of the bedforms adjusts, followed in turn by a relatively long period of the original low discharge. For the grain size and hydraulic conditions selected, the Froude number remains subcritical during the experiment, and sediment moves predominantly as bedload. Observations show rapid development of quasi‐two‐dimensional bedforms during the initial period of low flow with increasing wavelength and height over the initial low‐flow period. When the flow increases, the bedforms rapidly increase in wavelength and height, as expected from other empirical results. When the flow decreases back to the original discharge, the height of the bedforms quickly decreases in response, but the wavelength decreases much more slowly. Computational results using an unsteady two‐dimensional flow model coupled to a disequilibrium bedload transport model for the same conditions simulate the formation and initial growth of the bedforms fairly accurately and also predict an increase in dimensions during the high‐flow period. However, the computational model predicts a much slower rate of wavelength increase, and also performs less accurately during the final low‐flow period, where the wavelength remains essentially constant, rather than decreasing. In addition, the numerical results show less variability in bedform wavelength and height than the measured values; the bedform shape is also somewhat different. Based on observations, these discrepancies may result from the simplified model for sediment particle step lengths used in the computational approach. Experiments show that the particle step length varies spatially and temporally over the bedforms during the evolution process. Assuming a constant value for the step length neglects the role of flow alterations in the bedload sediment‐transport process, which appears to result in predicted bedform wavelength changes smaller than those observed. However, observations also suggest that three‐dimensional effects play at least some role in the decrease of bedform wavelength, so incorporating better models for particle hop lengths alone may not be sufficient to improve model predictions. Published in 2011. This article is a US Government work and is in the public domain in the USA.     

Turbulent flow structures in alluvial channels with curved cross‐sections under conditions of downward seepage

Experimental investigations have been done to analyze turbulent structures in curved sand bed channels with and without seepage. Measures of turbulent statistics such as time‐averaged near‐bed velocities, Reynolds stresses, thickness of roughness sublayer and shear velocities were found to increase with application of downward seepage. Turbulent kinetic energy and Reynolds normal stresses are increased in the streamwise direction under the action of downward seepage, causing bed particles to move rapidly. Analysis of bursting events shows that the relative contributions of all events (ejections, sweeps and interactions) increase throughout the boundary layer, and the thickness of the zone of dominance of sweep events, which are responsible for the bed material movement, increases in the case of downward seepage. The increased sediment transport rate due to downward seepage deforms the cross‐sectional geometry of the channel made of erodible boundaries, which is caused by an increase in flow turbulence and an associated decrease in turbulent kinetic energy dissipation and turbulent diffusion.     

Influence of compound bedforms on hydraulic roughness in a tidal environment

The effect exerted by the seabed morphology on the flow is commonly expressed by the hydraulic roughness, a fundamental parameter in the understanding and simulation of hydro- and sediment dynamics in coastal areas. This study quantifies the hydraulic roughness of large compound bedforms throughout a tidal cycle and investigates its relationship to averaged bedform dimensions. Consecutive measurements with an acoustic Doppler current profiler and a multibeam echosounder were carried out in the Jade tidal channel (North Sea, Germany) along large compound bedforms comprising ebb-oriented primary bedforms with superimposed smaller secondary bedforms. Spatially averaged velocity profiles produced log-linear relationships which were used to calculate roughness lengths. During the flood phase, the velocity profiles were best described by a single log-linear fit related to the roughness created by the secondary bedforms. During the ebb phase, the velocity profiles were segmented, showing the existence of at least two boundary layers: a lower one scaling with the superimposed secondary bedforms and an upper one scaling with the ebb-oriented primary bedforms. The drag induced by the primary bedform during the ebb phase is suggested to be related to flow expansion, separation, and recirculation on the downstream side of the bedform. Three existing formulas were tested to predict roughness lengths from the local bedform dimensions. All three predicted the right order of magnitude for the average roughness length but failed to predict its variation over the tidal cycle.     

Experimental study on transient and steady‐state dynamics of bedforms in supply limited configuration

The purpose of the present study is to investigate experimentally the development of bedforms in a configuration where the sediment supply is limited. The experimental setup is a rectangular closed duct combining an innovative system to control the rate of sediment supply Q_in , and a digitizing system to measure in real time the 3D bedform topography. We carried out different sets of experiments with two sediment sizes (100 µm and 500 µm) varying both the sediment supply and the water flow rate to obtain a total of 46 different configurations. After a transient phase, steady sub‐centimeter bedforms of various shapes have been observed: barchans dunes, straight transverse dune, linguoid transverse dunes and bedload sheets. Height, spacing, migration speed, and mean bed elevation of the equilibrium bedforms were measured. For a given flow rate, two regimes were identified with fine sediment: (i) a monotonic increasing regime where the equilibrium bedform height and velocity increase with the sediment supply rate Q_in and (ii) an invariant regime for which both parameters are almost independent of Q_in. For coarse sediment, only the first regime is observed. We interpret the saturation of height and velocity for fine sediment bedforms as the transition from a supply‐limited regime to a transport‐limited regime in which the bedload flux has reached its maximum value under the prevailing flow conditions. We also demonstrate that all experiments can be rescaled if the migration speed and height of the bedforms are, respectively, divided and multiplied by the cube of the shear velocity. This normalization is independent of grain size and of bedform morphology. These experimental results provide a new quantification of the factors controlling equilibrium height and migration speed of bedforms in supply‐limited conditions against which theoretical and numerical models can be tested.     

In situ quantification of spatial and temporal variability of hyporheic exchange in static and mobile gravel‐bed rivers

Seepage meters modified for use in flowing water were used to directly measure rates of exchange between surface and subsurface water in a gravel‐ and cobble bed river in western Pennsylvania, USA (Allegheny River, Q_mean = 190 m³/s) and a sand‐ and gravel‐bed river in Colorado, USA (South Platte River, Q_mean = 9·7 m³/s). Study reaches at the Allegheny River were located downstream from a dam. The bed was stable with moss, algae, and river grass present in many locations. Median seepage was + 0·28 m/d and seepage was highly variable among measurement locations. Upward and downward seepage greatly exceeded the median seepage rate, ranging from + 2·26 (upward) to ? 3·76 (downward) m/d. At the South Platte River site, substantial local‐scale bed topography as well as mobile bedforms resulted in spatial and temporal variability in seepage greatly in exceedence of the median groundwater discharge rate of 0·24 m/d. Both upward and downward seepage were recorded along every transect across the river with rates ranging from + 2·37 to ? 3·40 m/d. Despite a stable bed, which commonly facilitates clogging by fine‐grained or organic sediments, seepage rates at the Allegheny River were not reduced relative to those at the South Platte River. Seepage rate and direction depended primarily on measurement position relative to local‐ and meso‐scale bed topography at both rivers. Hydraulic gradients were small at nearly all seepage‐measurement locations and commonly were not a good indicator of seepage rate or direction. Therefore, measuring hydraulic gradient and hydraulic conductivity at in‐stream piezometers may be misleading if used to determine seepage flux across the sediment‐water interface. Such a method assumes that flow between the well screen and sediment‐water interface is vertical, which appears to be a poor assumption in coarse‐grained hyporheic settings. Copyright © 2011 John Wiley & Sons, Ltd.     

How do bedform patterns arise? New views on the role of bedform interactions within a set of boundary conditions

One explanation for bedform patterns is self‐organization in which the pattern emerges because of interactions among the bedforms themselves. Models, remote images, field studies and lab experiments have identified bedform interactions that involve whole bedforms, only bedform defects, or that are remote interactions between bedforms. It is proposed that bedform interactions form a spectrum from constructive to regenerative in pattern development. Constructive interactions, including merging, lateral linking, cannibalization, and remote transfer of sediment, push the system toward fewer, larger, more widely spaced bedforms. Regenerative interactions, including bedform splitting, defect creation and calving, push the system back toward a more initial state. Other interactions, including off‐center collision, defect migration, and bedform and defect repulsion, cause pattern change, but may not be strongly constructive or regenerative. Although bedform interactions are ubiquitous to any field of bedforms, their dynamics, flow‐field modification, and impact upon measurable pattern parameters are yet poorly understood. Most bedform interactions span bedform types and fluids, supporting the hypothesis that pattern emerges from dynamics at the bedform level in a hierarchy that includes lower levels of bedform‐flow and grain–fluid interactions. Bedform interactions alone, however, cannot account for the rich diversity of bedform patterns in nature. It is proposed that field diversity arises because of boundary conditions, which are the environmental variables within which a field evolves. Conceptually, boundary conditions modify the shape of the attractor toward which a field evolves, possibly by altering the type and frequency of bedform interactions. Boundary conditions are broadly similar within system types, but are unique for each bedform field so that no two are ever exactly alike. Although aeolian and fluvial systems share some types of boundary conditions, flow depth is a unique boundary condition in shallow fluvial systems. Copyright © 2009 John Wiley & Sons, Ltd.     

Grain‐size distribution patterns of a point bar system in the Usri River,India

Grain‐size distribution patterns in a point bar system of the Usri River, India, were critically analysed in the light of log‐normal, log‐hyperbolic and log‐skew‐Laplace distribution models. Sand samples were collected from the cross‐bedding foreset of different sizes of bedform; the objectives were to (i) study whether bedform heights have any role in grain‐size distribution patterns, (ii) offer a best‐fit statistical model, (iii) study the downstream variation of size‐sorting in a point bar system, and (iv) study the mechanism of grain sorting. The results indicate that the bedform heights have no role in grain‐size distribution patterns. Quantitatively when the errors in three distribution models were analysed, it was observed that the log‐normal distribution is the best‐fit statistical model and the next one is the log‐skew‐Laplace. However, in the upper reaches of the river, log‐normal distribution is the best‐fit model in the case of large bedforms, whereas in the lower reaches the log‐normal model is the best‐fit one in the case of small bed forms. It is also observed that within a point bar, for large and small bedforms, there is a tendency for mean grain size to decrease downstream. Between point bars for large bedforms there is no consistency in decreasing grain size downstream, whereas for small bed forms the decrease of grain size downstream is observed except near the confluence at Palkia. With distance of transport, the coarser and finer fractions of sediments are gradually chopped off. The coarser fractions are buried below the advancing bedforms on the lee sides and the finer ones are transported further downstream. Thus the finer admixture giving rise to the fining‐upward sequence overlies a carpet of coarser materials. This mechanism provides a clue to the process of grain sorting in the fluvial environment. An interpretation has been offered for the log‐normality of the grain‐size distribution pattern. During prolonged transportation in a fluvial environment, the larger grain‐size fractions are gradually chopped off and buried below the advancing bedforms on their lee sides. On the other hand, the finer fractions are transported further downstream in suspension. Thus the narrow, intermediate size fraction takes active part in the distribution patterns leading to the generation of unimodality and a symmetric distribution pattern downstream, which are the main criteria for log‐normality. Similarly, increase of bedform size is the effect of increase of stream power and Froude number leading to the selective segregation of bed materials. Thus the intermediate size fractions take a more active part than the coarser and the finer size fractions in developing log‐normality. Besides the hydrodynamic parameters of the Usri, coarsening of grain size downstream has been attributed to (i) the aggrading nature of the Usri downstream, and (ii) the contribution of coarser materials to the Usri by its tributaries and bank erosion. Copyright © 2006 John Wiley & Sons, Ltd.     

Morphology of riffle–pool sequences in the River Severn,England

Despite the occurrence of riffle–pool sequences in many rivers there are few data concerning riffle–pool unit morphology. Of many criteria proposed to identify riffle–pool units, only three methods can be regarded as objective and robust. These are the ‘zero‐crossing’, the ‘spectral analysis’ and the ‘control‐point’ methods. In this paper statistics are developed using the first two of these methods to describe the streamwise morphology of 275 riffles and 285 pools which form a continuous 32·1 km reach of the bed of the River Severn in Shropshire, England. Yalin's theoretical relationship between the average riffle:pool unit length ( λ _p) and channel width ( W ), λ _p = 3 W , applies to the River Severn. Reach‐average riffle height ( H ) is a constant proportion of bankfull depth ( h ); typically H ≅ 0·16 h . Riffle height is a positive function of riffle length. Pool depth is a positive function of pool length. However, both riffle length and pool length increase more rapidly than the bed‐level amplitude, such that long riffles or pools are relatively ‘flat’. As channel gradient reduces, bedforms flatten and become more asymmetric as riffle stoss sides and the proximal slope of pools lengthen at the expense of riffle lee sides and pool distal slopes. The statistical relationships between riffle steepness (H/L) and water depth are similar to those for equilibrium subaqueous dunes. The Severn data are consistent with Yalin's theoretical analysis relating riffle bedform length (L _r) to water depth, i.e. L _r = α2π h, wherein α ≅ 1 for steep near‐equilibrium bedforms but α ≅ 2 to 3 as the relative depth decreases and riffles become long, low features. Theoretical consideration and turbulence data indicate that the frequency of coherent turbulent‐flow structures associated with the riffle–pool mixing length in the Severn should be of the order of 50 to 100 s. The morphological similarity of the steepest River Severn riffles with dunes raises intriguing questions with respect to self‐similar, convergent organization of periodic alluvial bedforms and to bedform dynamic classification particularly. Copyright © 2000 John Wiley & Sons, Ltd.     

Numerical modelling of downstream migrating antidunes

A numerical model is presented that compute the geometrical dimensions and movement of downstream migrating antidunes. The model solves the Navier–Stokes equations together with the k‐epsilon turbulence model to find the water flow field over the bedforms. A two‐dimensional width‐averaged grid is used. The bed elevation changes are computed by solving the convection–diffusion equation for suspended sediments and bedload, together with the Engelund–Hansen sediment transport formula. The free surface is computed with an algorithm based on water continuity in the surface cells. Non‐orthogonal adaptive grids were used, moving vertically with the computed location of the bed and the free water surface. The numerical model was tested on data from a physical model study where regular downstream migrating antidunes had been observed. The numerical model started out with a flat bed and the trains of antidunes formed over time. Many of the physical processes observed in earlier studies were replicated by the numerical model. Four dune parameters were computed in the current tests: The antidune wavelength, height and celerity, together with the average water depth. The antidune wavelengths were best predicted with an accuracy of 3 to 8% compared with the measurements. The antidune heights were computed with a deviation of 11 to 25% compared with an empirical formula. The water depths over the antidunes were predicted with an accuracy of 3 to 9% related to the measured values. The average antidune celerity was the parameter with largest deviation: For the coarsest grid it was overpredicted with 37%. Copyright © 2017 John Wiley & Sons, Ltd.     

EXPERIMENTAL STUDY ON AGGRADATION

１ＩＮＴＲＯＤＵＣＴＩＯＮＨｕｍａｎａｃｔｉｖｉｔｉｅｓｍａｙｉｎｄｕｃｅｓｉｇｎｉｆｉｃａｎｔｃｈａｎｇｅｓｉｎｓｅｄｉｍｅｎｔｔｒａｎｓｐｏｒｔｃａｐａｃｉｔｙｏｆａｌｕｖｉａｌｒｉｖｅｒｃｈａｎｎｅｌｓａｎｄｃａｕｓｅｃｈａｎｇｅｓｉｎｔｈｅ...     

A method for estimating spatially variable seepage and hydraulic conductivity in channels with very mild slopes

Infiltration along ephemeral channels plays an important role in groundwater recharge in arid regions. A model is presented for estimating spatial variability of seepage due to streambed heterogeneity along channels based on measurements of streamflow‐front velocities in initially dry channels. The diffusion‐wave approximation to the Saint‐Venant equations, coupled with Philip's equation for infiltration, is connected to the groundwater model MODFLOW and is calibrated by adjusting the saturated hydraulic conductivity of the channel bed. The model is applied to portions of two large water delivery canals, which serve as proxies for natural ephemeral streams. Estimated seepage rates compare well with previously published values. Possible sources of error stem from uncertainty in Manning's roughness coefficients, soil hydraulic properties and channel geometry. Model performance would be most improved through more frequent longitudinal estimates of channel geometry and thalweg elevation, and with measurements of stream stage over time to constrain wave timing and shape. This model is a potentially valuable tool for estimating spatial variability in longitudinal seepage along intermittent and ephemeral channels over a wide range of bed slopes and the influence of seepage rates on groundwater levels. Copyright © 2012 John Wiley & Sons, Ltd.     

Robust methods for the decomposition and interpretation of compound dunes applied to a complex hydromorphological setting

Underwater dunes are a morphological feature that are explored by marine scientists and coastal engineers alike. This study presents new methodologies in order to simplify bedform identification and morphodynamic analyses. Specifically, subaqueous compound dunes are decomposed with a simple yet extensive tracking algorithm, which relies on a repeated evaluation of unfiltered bed elevation profiles according to five predefined length classes. In a second step, morphological trends are assessed in the form of bed migration rates, bed slope asymmetries and net sediment changes, in which all parameters are referred to equidistant sections of the examined fairway stretch. This integrated approach not only avoids the challenges in weighting the varying size and abundance of dunes of different scales but also ensures comparability between dune-specific and areal parameters, which significantly improves the interpretation of the morphological setting as a whole. The developed methods are applied to the Outer Jade fairway, an anthropogenically influenced and regularly maintained waterway in the German Bight, and allow scrutiny of spatio-temporal trends in this region. Based on a unique data set of 100 sequential high-quality echo-sounding surveys, various types of bedforms are identified, comprising large-scale primary as well as superimposing secondary dunes that are assumed to interfere with each other. Temporal trends show a long-term rise of the troughs of major bedforms and constant maximum crest elevations near the official maintenance depth, which matches the observed long-term aggradation of sediments. The spatial distribution of integrated morphodynamic parameters reflects a previously described zone of primary dune convergence and facilitates the precise localization of this geophysical singularity. The presented findings both confirm the robustness of the proposed methodologies and, in return, enhance the understanding of morphological processes in the Outer Jade. © 2020 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.