Synthesis and properties of ammoniojarosites prepared with iron-oxidizing acidophilic microorganisms at 22-65 °C

Ammoniojarosite [(NH₄,H₃O)Fe₃(OH)₆(SO₄)₂], a poorly soluble basic ferric sulfate, was produced by microbiological oxidation of ferrous sulfate at pH 2.0-3.0 over a range of concentrations (5.4-805 mM) and temperatures (22-65 °C). Ammoniojarosites were also produced by chemical (abiotic) procedures in parallel thermal (36-95 °C) experiments. At 36 °C, schwertmannite [ideally Fe₈O₈(OH)₆(SO₄)] was the only solid product formed at <10 mM concentrations. Between 11.5 and 85.4 mM , a mixed product of ammoniojarosite and schwertmannite precipitated, as identified by X-ray diffraction. In excess of 165 mM , ammoniojarosite was the only solid phase produced. An increase in the incubation temperature using thermoacidophiles at 45 and 65 °C accelerated the formation of ammoniojarosite in culture solutions containing 165 mM . Both the biogenic and chemical ammoniojarosites were yellow (2Y-4Y in Munsell hue), low surface area (<1 m²/g), well crystalline materials with average c_o and a_o unit cell parameters of 17.467 ± 0.048 Å and 7.330 ± 0.006 Å, respectively. Strong positive correlations were observed between unit cell axial ratios (c_o/a_o) and increasing synthesis temperature in both biotic and abiotic systems. All samples were N deficient compared to stoichiometric ammoniojarosite, and both chemical and X-ray data indicated partial replacement of by H₃O⁺ to form solid solutions with 0.14-0.24 mole H₃O⁺ per formula unit. The morphology of the biogenic jarosites included aggregated discs, pseudo-cubic crystals and botryoidal particles, whereas the chemical specimens prepared at 36-95 °C were composed of irregular crystals with angular edges. Morphological information may thus be useful to evaluate environmental parameters and mode of formation. The data may also have application in predicting phase boundary conditions for Fe(III) precipitation in biogeochemical processes and treatment systems involving acid sulfate waters.     

A potentiometric study of the stability of aqueous yttrium-acetate complexes from 25 to 175 °C and 1-1000 bar

The stability of yttrium-acetate (Y-Ac) complexes in aqueous solution was determined potentiometrically at temperatures 25-175 °C (at P_s) and pressures 1-1000 bar (at 25 and 75 °C). Measurements were performed using glass H⁺-selective electrodes in potentiometric cells with a liquid junction. The species YAc²⁺ and were found to dominate yttrium aqueous speciation in experimental solutions at 25-100 °C (log [Ac⁻] < −1.5, pH < 5.2), whereas at 125, 150 and 175 °C introduction of into the Y-Ac speciation model was necessary. The overall stability constants β_n were determined for the reaction

     

Gold and copper partitioning in magmatic-hydrothermal systems at 800 °C and 100 MPa

Porphyry-type ore deposits sometimes contain fluid inclusion compositions consistent with the partitioning of copper and gold into vapor relative to coexisting brine at the depositional stage. However, this has not been reproduced experimentally at magmatic conditions. In an attempt to determine the conditions under which copper and gold may partition preferentially into vapor relative to brine at temperatures above the solidus of granitic magmas, we performed experiments at 800 °C, 100 MPa, oxygen fugacity () buffered by Ni-NiO, and fixed at either 3.5 × 10⁻² by using intermediate solid solution-pyrrhotite, or 1.2 × 10⁻⁴ by using intermediate solid solution-pyrrhotite-bornite. The coexisting vapor (∼3 wt.% NaCl eq.) and brine (∼68 wt.% NaCl eq.) were composed initially of NaCl + KCl + HCl + H₂O, with starting HCl set to <1000 μg/g in the aqueous mixture. Synthetic vapor and brine fluid inclusions were trapped at run conditions and subsequently analyzed by laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS). Our experiments demonstrate that copper and gold partitioned strongly into the magmatic volatile phase(s) (MVP) (i.e., vapor or brine) relative to a silicate melt over the entire imposed range of . Nernst style partition coefficients between coexisting brine (b) and melt (m), D^b/m (±1σ), range from 3.6(±2.2) × 10¹ to 4(±2) × 10² for copper and from 1.2(±0.6) × 10² to 2.4(±2.4) × 10³ for gold. Partition coefficients between coexisting vapor (v) and melt, D^v/m range from 2.1 ± 0.7 to 18 ± 5 and 7(±3) × 10¹ to 1.6(±1.6) × 10² for copper and gold, respectively. Partition coefficients for all experiments between coexisting brine and vapor, D^b/v (±1σ), range from 7(±2) to 1.0(±0.4) × 10² and 1.7(±0.2) to 15(±2) for copper and gold, respectively. Observed average D^b/v at an of 1.2 × 10⁻⁴ were elevated, 95(±5) and 15 ± 1 for copper and gold, respectively, relative to those at the higher of 3.5 × 10⁻² where D^b/v were 10(±5) for copper and 7(±6) for gold. Thus, there is an inverse relationship between the and the D^b/v for both copper and gold with increasing resulting in a decrease in the D^b/v signifying increased importance of the vapor phase for copper and gold transport. This suggests that copper and gold may complex with volatile S-species as well as Cl-species at magmatic conditions, however, none of the experiments of our study at 800 °C and 100 MPa had a D^b/v ? 1. We did not directly determine speciation, but infer the existence of some metal-sulfur complexes based on the reported data. We suggest that copper and gold partition preferentially into the brine in most instances at or above the wet solidus. However, in most systems, the mass of vapor is greater than the mass of brine, and vapor transport of copper and gold may become more important in the magmatic environment at higher , lower , or near the critical point in a salt-water system. A D^b/v ? 1 at subsolidus hydrothermal conditions may also occur in response to changes in temperature, , , and/or acidity.Additionally, both copper and gold were observed to partition into intermediate solid solution and bornite much more strongly than into vapor, brine or silicate melt. This suggests that, although vapor and brine are both efficient at removing copper and gold from a silicate melt, the presence of Cu-Fe sulfides can sequester a substantial portion of the copper and gold contained within a silicate melt if the Cu-Fe sulfides are abundant.     

Dissociation constants and speciation in aqueous Li2SO4 and K2SO4 from measurements of electrical conductance to 673 K and 29 MPa

The electrical conductivities of aqueous solutions of Li₂SO₄ and K₂SO₄ have been measured at 523-673 K at 20-29 MPa in dilute solutions for molalities up to 2 × 10⁻² mol kg⁻¹. These conductivities have been fitted to the conductance equation of Turq, Blum, Bernard, and Kunz with a consensus mixing rule and mean spherical approximation activity coefficients. In the temperature interval 523-653 K, where the dielectric constant, ε, is greater than 14, the electrical conductance data can be fitted by a solution model which includes ion association to form , , and , where M is Li or K. The adjustable parameters of this model are the first and second dissociation constants of the M₂SO₄. For the 673 K and 300 kg m⁻³ state point where the Coulomb interactions are the strongest (dielectric constant, ε = 5), models with more extensive association give good fits to the data. In the case of the Li₂SO₄ model, including the multi-ion associate, , gave an extremely good fit to the conductance data.     

An XAS study of the structure and thermodynamics of Cu(I) chloride complexes in brines up to high temperature (400 °C, 600 bar)

The transport and deposition of copper in saline hydrothermal fluids are controlled by the stability of copper(I) complexes with ligands such as chloride. Despite their role in the formation of most hydrothermal copper deposits, the nature and stability of Cu(I) chloride complexes in highly saline brines remains controversial. We present new X-ray absorption data (P = 600 bar, T = 25-400 °C, salinity up to 17.2 m Cl), which indicate that the linear (x = 1, 2) complexes are stable up to supercritical conditions. Distorted trigonal planar complexes predominate at room temperature and at high salinity (>3 m LiCl): subtle changes in the XANES spectrum with increasing salinity may reflect geometric distortions of this complex. Similar changes were observed in UV-Vis data [Liu, W., Brugger, J., McPhail, D.C., Spiccia, L., 2002. A spectrophotometric study of aqueous copper(I) chloride complexes in LiCl solutions between 100 °C and 250 °C. Geochim. Cosmochim. Acta66, 3615-3633], and were erroneously interpreted as a new species, . Our XAS data and ab-initio XANES calculations show that this tetrahedral species is not present to any significant degree in our solutions. The stability of the complexe decreases with increasing temperature; under supercritical conditions and in brines under magmatic-hydrothermal conditions (e.g., 15.58 m Cl, 400 °C, 600 bar), only the linear Cu(I) chloride complexes were observed. This result and the instability of the complex are also consistent with the recent ab-initio molecular dynamic calculations of Sherman [Sherman D. M.(2007) Complexation of Cu⁺ in hydrothermal NaCl brines: ab-initio molecular dynamics and energetics. Geochim. Cosmochim. Acta71, 714-722]. This study illustrates the power of the quantitative nature of XANES and EXAFS measurements for deciphering the speciation of weak transition metal complexes up to magmatic-hydrothermal conditions.The systematic XANES data are used to retrieve the formation constant for at 150 °C, which is in good agreement with the reinterpretation of the UV-Vis data of Liu et al. (Liu et al., 2002). At high temperatures (?400 °C), the solubility of chalcopyrite in equilibrium with hematite-magnetite-pyrite and K-feldspar-muscovite-quartz calculated with the new properties is lower than that calculated using the previous model, and the calculated solubilities are at the lower end of the range of values measured in brine inclusions from porphyry copper systems.     

Oxygen isotope fractionation between apatite-bound carbonate and water determined from controlled experiments with synthetic apatites precipitated at 10-37 °C

The oxygen isotope fractionation between the structural carbonate of inorganically precipitated hydroxyapatite (HAP) and water was determined in the range 10-37 °C. Values of 1000 ln α() are linearly correlated with inverse temperature (K) according to the following equation: 1000 ln α() = 25.19 (±0.53)·T⁻¹ − 56.47 (±1.81) (R² = 0.998). This fractionation equation has a slightly steeper slope than those already established between calcite and water ( [O’Neil et al., 1969] and [Kim and O’Neil, 1997]) even though measured fractionations are of comparable amplitude in the temperature range of these experimental studies. It is consequently observed that the oxygen isotope fractionation between apatite carbonate and phosphate increases from about 7.5‰ up to 9.1‰ with decreasing temperature from 37 °C to 10 °C. A compilation of δ¹⁸O values of both phosphate and carbonate from modern mammal teeth and bones confirms that both variables are linearly correlated, despite a significant scattering up to 3.5‰, with a slope close to 1 and an intercept corresponding to a 1000 ln α() value of 8.1‰. This apparent fractionation factor is slightly higher or close to the fractionation factor expected to be in the range 7-8‰ at the body temperature of mammals.     

Coupled phase and aqueous species equilibrium of the H2O-CO2-NaCl-CaCO3 system from 0 to 250 °C, 1 to 1000 bar with NaCl concentrations up to saturation of halite

A model is developed for the calculation of coupled phase and aqueous species equilibrium in the H₂O-CO₂-NaCl-CaCO₃ system from 0 to 250 °C, 1 to 1000 bar with NaCl concentrations up to saturation of halite. The vapor-liquid-solid (calcite, halite) equilibrium together with the chemical equilibrium of H⁺, Na⁺, Ca²⁺, , Ca(OH)⁺, OH⁻, Cl⁻, , , CO_2(aq) and CaCO_3(aq) in the aqueous liquid phase as a function of temperature, pressure, NaCl concentrations, CO_2(aq) concentrations can be calculated, with accuracy close to those of experiments in the stated T-P-m range, hence calcite solubility, CO₂ gas solubility, alkalinity and pH values can be accurately calculated. The merit and advantage of this model is its predictability, the model was generally not constructed by fitting experimental data.One of the focuses of this study is to predict calcite solubility, with accuracy consistent with the works in previous experimental studies. The resulted model reproduces the following: (1) as temperature increases, the calcite solubility decreases. For example, when temperature increases from 273 to 373 K, calcite solubility decreases by about 50%; (2) with the increase of pressure, calcite solubility increases. For example, at 373 K changing pressure from 10 to 500 bar may increase calcite solubility by as much as 30%; (3) dissolved CO₂ can increase calcite solubility substantially; (4) increasing concentration of NaCl up to 2 m will increase calcite solubility, but further increasing NaCl solubility beyond 2 m will decrease its solubility.The functionality of pH value, alkalinity, CO₂ gas solubility, and the concentrations of many aqueous species with temperature, pressure and NaCl_(aq) concentrations can be found from the application of this model. Online calculation is made available on www.geochem-model.org/models/h2o_co2_nacl_caco3/calc.php.     

Water speciation and diffusion in haploandesitic melts at 743-873 K and 100 MPa

Water is an important volatile component in andesitic eruptions and deep-seated andesitic magma chambers. We report an investigation of H₂O speciation and diffusion by dehydrating haploandesitic melts containing ?2.5 wt.% water at 743-873 K and 100 MPa in cold-seal pressure vessels. FTIR microspectroscopy was utilized to measure species [molecular H₂O (H₂O_m) and hydroxyl group (OH)] and total H₂O (H₂O_t) concentration profiles on the quenched glasses from the dehydration experiments. The equilibrium constant of the H₂O speciation reaction H₂O_m+O?2OH, K = (X_OH)²/(X_H2OmX_O) where X means mole fraction on a single oxygen basis, in this Fe-free andesite varies with temperature as ln K = 1.547-2453/T where T is in K. Comparison with previous speciation data on rhyolitic and dacitic melts indicates that, for a given water concentration, Fe-free andesitic melt contains more hydroxyl groups. Water diffusivity at the experimental conditions increases rapidly with H₂O concentration, contrary to previous H₂O diffusion data in an andesitic melt at 1608-1848 K. The diffusion profiles are consistent with the model that molecular H₂O is the diffusion species. Based on the above speciation model, H₂O_m and H₂O_t diffusivity (in m²/s) in haploandesite at 743-873 K, 100 MPa, and H₂O_t ? 2.5 wt.% can be formulated as

     

An in situ XAS study of copper(I) transport as hydrosulfide complexes in hydrothermal solutions (25-592 °C, 180-600 bar): Speciation and solubility in vapor and liquid phases

Chloride and hydrosulfide are the principal ligands assumed to govern transport of copper in hydrothermal fluids. Existing solubility experiments suggest that Cu(I)-hydrosulfide complexes are dominant compared to chloride complexes at low salinities in alkaline solutions (H₂S_(aq)/HS⁻ pH buffer), and may be important in transporting Cu in low density magmatic vapors, potentially controlling the liquid-vapor partitioning of Cu. This study provides the first in situ evidence of the solubility of copper sulfides and the nature and structure of the predominant Cu species in sulfur-containing fluids at temperatures up to 592 °C and pressures of 180-600 bar. XANES and EXAFS data show that at elevated T (?200 °C), Cu solubility occurs via a linear Cu complex. At 428 °C in alkaline solutions, Cu is coordinated by two sulfur atoms in a distorted linear coordination (angle ∼150-160°). This geometry is consistent with the species predicted by earlier solubility studies. In addition, in situ measurements of the solubility of chalcocite in 2 m NaHS solutions performed in this study are in remarkably good agreement with the solubilities calculated using available thermodynamic data for Cu(I)-hydrosulfide complexes, also supporting the interpretation of speciation in these studies and validating the extrapolation of low-T thermodynamic properties for to high P-T. Data on phase separation for the 2 m NaHS solution show that while significant amounts of copper can be partitioned into the vapor phase, there is no indication for preferential partitioning of Cu into the vapor. This is consistent with recent partitioning experiments conducted in autoclaves by Pokrovski et al. (2008a) and Simon et al. (2006). XANES data suggest that the species present in the low density phase is very similar to that present in the high density liquid, i.e., , although Cu(HS)(H₂S)⁰ cannot be excluded on the basis of XAS data.     

Oxygen and hydrogen isotope fractionation in serpentine-water and talc-water systems from 250 to 450 °C, 50 MPa

Oxygen and hydrogen isotope fractionation factors in the talc-water and serpentine-water systems have been determined by laboratory experiment from 250 to 450 °C at 50 MPa using the partial exchange technique. Talc was synthesized from brucite + quartz, resulting in nearly 100% exchange during reaction at 350 and 450 °C. For serpentine, D-H exchange was much more rapid than ¹⁸O-¹⁶O exchange when natural chrysotile fibers were employed in the initial charge. In experiments with lizardite as the starting charge, recrystallization to chrysotile enhanced the rate of ¹⁸O-¹⁶O exchange with the coexisting aqueous phase. Oxygen isotope fractionation factors in both the talc-water and serpentine-water systems decrease with increasing temperature and can be described from 250 to 450 °C by the relationships: 1000 ln  = 11.70 × 10⁶/T² − 25.49 × 10³/T + 12.48 and 1000 ln  = 3.49 × 10⁶/T² − 9.48 where T is temperature in Kelvin. Over the same temperature interval at 50 MPa, talc-water D-H fractionation is only weakly dependent on temperature, similar to brucite and chlorite, and can be described by the equation: 1000 ln = 10.88 × 10⁶/T² − 41.52 × 10³/T + 5.61 where T is temperature in Kelvin. Our D-H serpentine-water fractionation factors calibrated by experiment decrease with temperature and form a consistent trend with fractionation factors derived from lower temperature field calibrations. By regression of these data, we have refined and extended the D-H fractionation curve from 25 to 450 °C, 50 MPa as follows: 1000 ln  = 3.436 × 10⁶/T² − 34.736 × 10³/T + 21.67 where T is temperature in Kelvin. These new data should improve the application of D-H and ¹⁸O-¹⁶O isotopes to constrain the temperature and origin of hydrothermal fluids responsible for serpentine formation in a variety of geologic settings.     

Solubility of tin in (Cl, F)-bearing aqueous fluids at 700 °C, 140 MPa: A LA-ICP-MS study on synthetic fluid inclusions

Synthetic fluid inclusions in quartz were grown from cassiterite-saturated fluids in cold-seal pressure vessels at and subsequently analyzed by laser ablation-ICP-MS. Most inclusions were synthesized using a new technique that allows entrapment of fluid that had no immediate contact to the capsule walls, such that potential disequilibrium effects due to alloying could be avoided. Measured Sn solubilities increase with increasing ligand concentration in the fluid, ranging from 100 to 800 ppm in NaCl-bearing fluids (5-35 wt% NaCl), from 70 to 2000 ppm in HF-bearing fluids (0.5-3.2 m HF), and from 0.8 to 11 wt% in HCl-bearing fluids (0.5-4.4 m HCl). Two runs performed with the in-situ cracking method after 1 week of pre-equilibration demonstrate that the speed of hydrogen diffusion through the capsule wall relative to that of fluid inclusion formation is a critical factor in f_O2-dependent solubility studies. Graphical evaluation of the solubility data suggests that Sn may have been dissolved as Sn(OH)Cl in the NaCl-bearing fluids, as Sn(OH)Cl and SnCl₂ in the HCl-bearing fluids, and as SnF₂ in the HF-bearing fluids. Experiments with NaF-bearing fluids produced an additional melt phase with an approximate composition of 53 wt% SiO₂, 25 wt% H₂O, 14 wt% NaF and 8 wt% SnO, which caused the composition of the coexisting fluid to be buffered at 0.5 wt% NaF and 150 ppm Sn. Fluorine-rich, peralkaline melts may therefore serve as important transport media for Sn in the final crystallization stages of tin granites. Based on the available cassiterite-solubility data in fluids and melts, in natural granite systems is estimated to be in the order of 0.1-4 (depending on their aluminosity), suggesting that Sn is not easily mobilized by magmatic-hydrothermal fluids. This interpretation is in accordance with the high degrees of Sn-enrichment commonly observed in highly fractionated melt inclusions. is primarily controlled by the HCl concentration in the fluid, which in turn is a function of the aluminum saturation index of the magma. Compared to HCl, the effect of fluorine on is subordinate.     

Dissolution kinetics of calcite at 50-70 °C: An atomic force microscopic study under near-equilibrium conditions

Direct measurements of calcite faces were performed using in situ atomic force microscopy (AFM) to reveal the dissolution processes as a function of solution saturation state and temperature. Time-sequential AFM images demonstrated that step velocities at constant temperature increased with increasing undersaturation. The anisotropy of obtuse and acute step velocities appeared to become more significant as solutions approached equilibrium and temperature increased. At saturation state Ω > 0.02, a curvilinear boundary was formed at the intersection of two acute steps and the initially rhombohedral etch pit exhibited a nearly triangular shape. This suggests that the and steps may not belong to the calcite-aqueous solution equilibrium system. Further increase in the saturation state (Ω ? 0.3) led to a lack of etch pit formation and dissolution primarily occurred at existing steps, in accordance with Teng (2004). Analysis of step kinetics at different temperatures yielded activation energies of 25 ± 6 kJ/mol and 14 ± 13 kJ/mol for obtuse and acute steps, respectively. The inconsistencies in etch pit morphology, step anisotropy, and step activation energies from the present study with those of studies far-from-equilibrium can be explained by increased influence of the backward reaction, or growth, near-equilibrium. We propose that the backward reaction occurs preferentially at the acute-acute kink sites. The kinetics and effective activation energies of near-equilibrium calcite dissolution presented in this work provide accurate experimental data under likely CO₂ sequestration conditions, and thus are crucial to the development of robust geochemical models that predict the long-term performance of mineral-trapped CO₂.     

Synthesis, characterization and thermochemistry of a Pb-jarosite

The enthalpy of formation from the elements of a well-characterized synthetic Pb-jarosite sample corresponding to the chemical formula (H₃O)_0.74Pb_0.13Fe_2.92(SO₄)₂(OH)_5.76(H₂O)_0.24 was measured by high temperature oxide melt solution calorimetry. This value ( = −3695.9 ± 9.7 kJ/mol) is the first direct measurement of the heat of formation for a lead-containing jarosite. Comparison to the thermochemical properties of hydronium jarosite and plumbojarosite end-members strongly suggests the existence of a negative enthalpy of mixing possibly related to the nonrandom distribution of Pb²⁺ ions within the jarosite structure. Based on these considerations, the following thermodynamic data are proposed as the recommended values for the enthalpy of formation from the elements of the ideal stoichiometric plumbojarosite Pb_0.5Fe₃(SO₄)₂(OH)₆:  = −3118.1 ± 4.6 kJ/mol,  = −3603.6 ± 4.6 kJ/mol and S° = 376.6 ± 4.5 J/(mol K). These data should prove helpful for the calculation of phase diagrams of the Pb-Fe-SO₄-H₂O system and for estimating the solubility product of pure plumbojarosite. For illustration, the evolution of the estimated solubility product of ideal plumbojarosite as a function of temperature in the range 5-45 °C was computed (Log(K_sp) ranging from −24.3 to −26.2). An Eh-pH diagram is also presented.     

Comparative carbonate and hydroxide complexation of cations in seawater

Comparative concentrations of carbonate and hydroxide complexes in natural solutions can be expressed in terms of reactions with bicarbonate that have no explicit pH dependence (). Stability constants for this reaction with n = 1 were determined using conventional formation constant data expressed in terms of hydroxide and carbonate. Available data indicate that stability constants appropriate to seawater at 25 °C expressed in the form are on the order of 10^4.2 for a wide range of cations (M^z+) with z = +1, +2 and +3. Φ₁ is sufficiently large that species appear to substantially dominate MOH^z−1 species in seawater. Evaluations of comparative stepwise carbonate and hydroxide stability constant behavior leading to the formation of n = 2 and n = 3 complexes suggest that carbonate complexes generally dominate hydroxide complexes in seawater, even for cations whose inorganic speciation schemes in seawater are currently presumed to be strongly dominated by hydrolyzed forms (). Calculated stability constants, and , indicate that the importance of carbonate complexation is sufficiently large that carbonate and hydroxide complexes would be generally comparable even if calculated Φ₂ and Φ₃ values are overestimated by two or more orders of magnitude. Inclusion of mixed ligand species in carbonate-hydroxide speciation models allows cation complexation intensities (M_T/[M^z+]) to be expressed in the following form:

     

The partitioning of molybdenum(VI) between aqueous liquid and vapour at temperatures up to 370 °C

We have conducted experiments to evaluate the vapour-liquid fractionation of Mo(VI) in the system MoO₃-NH₃-H₂O at 300-370 °C and saturated vapour pressure, using a two-chamber autoclave that allows separate trapping of the vapour and liquid. The measured total Mo concentrations in each phase were used to calculate a distribution coefficient, , which increases as the density of the vapour approaches that of the liquid, and is greater than one for pH ? 4. Molybdenum speciation in the vapour is described by a single complex, MoO₃H₂O. By contrast, thermodynamic modeling of the distribution of Mo species in the liquid indicates that bimolybdate (HMoO₄⁻) is the dominant aqueous species at the conditions of our experiments, and that molybdate (MoO₄²⁻) and molybdic acid (H₂MoO₄⁰) are present in smaller quantities. As vapour-liquid fractionation occurs between neutral species, it is governed by the reaction H₂MoO₄⁰(aq) = MoO₃ · H₂O(g). Fractionation is therefore controlled by the concentration of H₂MoO₄⁰ in the liquid, which increases with increasing temperature and decreasing pH. Owing to the pH dependence of , it cannot be used to describe Mo fractionation in aqueous vapour-liquid systems with compositions different than those of this study. We have therefore calculated a composition-independent (Henry’s Law) constant, , for each experimental point, using the measured total Mo concentration in the vapour and the modeled concentration of H₂MoO₄⁰ in the liquid. This constant may be applied to aqueous vapour-liquid systems of known liquid composition to estimate the concentration of Mo in a vapour for which little chemical information is available, and thereby supplement the available fractionation data for natural porphyry-forming systems. The results of this study demonstrate that at conditions typical of natural porphyry ore-forming systems, a significant amount of molybdenum fractionates into the vapour over the liquid, and the vapour may transport quantities of Mo in excess of that in the liquid at pH conditions below those of the muscovite-microcline reaction boundary.     

The system H2O-NaCl. Part II: Correlations for molar volume, enthalpy, and isobaric heat capacity from 0 to 1000 °C, 1 to 5000 bar, and 0 to 1 XNaCl

A set of correlations for the volumetric properties and enthalpies of phases in the system H₂O-NaCl as a function of temperature, pressure, and composition has been developed that yields accurate values from 0 to 1000 °C, 1 to 5000 bar, and 0 to 1 X_NaCl. The volumetric properties of all fluid phases from low-density vapor to hydrous salt melts and single-phase binary fluids at high pressures and temperatures, can be described by a simple equation

     

Effect of pH and organic ligands on the kinetics of smectite dissolution at 25 °C

Forward dissolution rates of Na-Montmorillonite (Wyoming) SWy-2 smectite (Ca_0.06Na_0.56)[Al_3.08Fe(III)_0.38Mg_0.54] [Si_7.93 Al_0.07]O₂₀(OH)₄ were measured at 25 °C in a mixed-flow reactor equipped with interior dialysis compartment (6-8 kDa membrane) as a function of pH (1-12), dissolved carbonate (0.5-10 mM), phosphate (10⁻⁵ to 0.03 M), and nine organic ligands (acetate, oxalate, citrate, EDTA, alginate, glucuronic acid, 3,4-dihydroxybenzoic acid, gluconate, and glucosamine) in the concentration range from 10⁻⁵ to 0.03 M. In organic-free solutions, the Si-based rates decrease with increasing pH at 1 ? pH ? 8 with a slope close to −0.2. At 9 ? pH ? 12, the Si-based rates increase with a slope of ∼0.3. In contrast, non-stoichiometric Mg release weakly depends on pH at 1 ? pH ? 12 and decreases with increasing pH. The empirical expression describing Si-release rates [R, mol/cm²/s] obtained in the present study at 25 °C, I = 0.01 M is given by

     

Thermodynamic studies of pyrrhotite-pyrite equilibria in the Ag-Fe-S system by solid-state galvanic cell technique at 518-723 K and total pressure of 1 atm

The reaction FeS₂(cr) + 2Ag(cr) = ‘FeS’(cr) + Ag₂S(cr) was studied by measuring the temperature dependence of the electromotive force (EMF) of the all-solid-state galvanic cell with common gas space:

(-)Pt|Ag|AgI|Ag₂S,‘FeS’,FeS₂|Pt(+)     

Trace element partitioning between ilmenite, armalcolite and anhydrous silicate melt: Implications for the formation of lunar high-Ti mare basalts

We performed a series of experiments at high pressures and temperatures to determine the partitioning of a wide range of trace elements between ilmenite (Ilm), armalcolite (Arm) and anhydrous lunar silicate melt, to constrain geochemical models of the formation of titanium-rich melts in the Moon. Experiments were performed in graphite-lined platinum capsules at pressures and temperatures ranging from 1.1 to 2.3 GPa and 1300-1400 °C using a synthetic Ti-enriched Apollo ‘black glass’ composition in the CaO-FeO-MgO-Al₂O₃-TiO₂-SiO₂ system. Ilmenite-melt and armalcolite-melt partition coefficients (D) show highly incompatible values for the rare earth elements (REE) with the light REE more incompatible compared to the heavy REE ( 0.0020 ± 0.0010 to 0.069 ± 0.010 for ilmenite; 0.0048 ± 0.0023 to 0.041 ± 0.008 for armalcolite). D values for the high field strength elements vary from highly incompatible for Th, U and to a lesser extent W (for ilmenite: 0.0013 ± 0.0008, 0.0035 ± 0.0015 and 0.039 ± 0.005, and for armalcolite 0.008 ± 0.003, 0.0048 ± 0.0022 and 0.062 ± 0.03), to mildly incompatible for Nb, Ta, Zr, and Hf (e.g. 0.28 ± 0.05 and : 0.76 ± 0.07). Both minerals fractionate the high field strength elements with D_Ta/D_Nb and D_Hf/D_Zr between 1.3 and 1.6 for ilmenite and 1.3 and 1.4 for armalcolite. Armalcolite is slightly more efficient at fractionating Hf from W during lunar magma ocean crystallisation, with D_Hf/D_W = 12-13 compared to 6.7-7.5 for ilmenite. The transition metals vary from mildly incompatible to compatible, with the highest compatibilities for Cr in ilmenite (D ∼ 7.5) and V in armalcolite (D ∼ 8.1). D values show no clear variation with pressure in the small range covered.Crystal lattice strain modelling of D values for di-, tri- and tetravalent trace elements shows that in ilmenite, divalent elements prefer to substitute for Fe while armalcolite data suggest REE replacing Mg. Tetravalent cations appear to preferentially substitute for Ti in both minerals, with the exception of Th and U that likely substitute for the larger Fe or Mg cations. Crystal lattice strain modelling is also used to identify and correct for very small (∼0.3 wt.%) melt contamination of trace element concentration determinations in crystals.Our results are used to model the Lu-Hf-Ti concentrations of lunar high-Ti mare basalts. The combination of their subchondritic Lu/Hf ratios and high TiO₂ contents requires preferential dissolution of ilmenite or armalcolite from late-stage, lunar magma ocean cumulates into low-Ti partial melts of deeper pyroxene-rich cumulates.     

Modeling the effects of bond environment on equilibrium iron isotope fractionation in ferric aquo-chloro complexes

Four or five sets of ab initio models, including Unrestricted Hartree Fock (UHF) and hybrid Density Functional Theory (DFT) are calculated for each species in a series of aqueous ferric aquo-chloro complexes: , , , FeCl₃(H₂O)₃, FeCl₃(H₂O)₂, , FeCl₅H₂O²⁻, , ) in order to determine the relative isotopic fractionation among the complexes, to compare the results of different models for the same complexes, to examine factors that influence the magnitude of the isotopic fractionation, and to compare bond-partner-driven fractionation with redox-driven fractionation.Relative to , all models show a nearly linear decrease in ⁵⁶Fe/⁵⁴Fe as the number of Cl⁻ ions per Fe³⁺ ion increases, with slopes of −0.8‰ to −1.0‰ per Cl⁻ at 20 °C. At 20 °C, 1000 ln β (β = ⁵⁶Fe/⁵⁴Fe reduced partition function ratio relative to a dissociated Fe atom) values range from 8.93‰ to 9.73‰ for , 8.04-9.12‰ for , 7.61-8.73‰ for , 7.14-8.25‰ for , and 3.09-4.41‰ for . The fractionation between and ranges from 1.5‰ to 2.6‰, depending on the model; this is comparable in magnitude to fractionation effects due to Fe³⁺/Fe²⁺ redox reactions. β values from the UHF models are consistently higher than those from the hybrid DFT models.Isotopic fractionation is shown to be sensitive to differences in ligand bond stiffness (above), coordination number, bond length, and the frequency of the asymmetric Fe-X stretching vibrational mode, as predicted by previous theoretical studies. Complexes with smaller coordination numbers have higher 1000 ln β (7.46‰, 5.25‰, and 3.48‰ for , ,, respectively, from the B3LYP/6-31G(d) model). Species with the same number of chlorides but fewer waters also show the effect of coordination number on 1000 ln β: (7.46‰ vs. 7.05‰ for FeCl₃(H₂O)₂ vs. FeCl₃(H₂O)₃ and 5.25‰ vs. 4.94‰ for vs. FeCl₅H₂O²⁻ with the B3LYP/6-31G(d) model). As more Fe-Cl bonds substitute for Fe-OH₂ bonds (with a resulting decrease in β), the lengths of the Fe-Cl bonds and the Fe-O bonds increase.Preliminary modeling of shows an Fe³⁺/Fe²⁺ fractionation of 3.2‰ for the B3LYP/6-31G(d) model, in agreement with previous studies. The addition of an explicit outer hydration sphere of 12 H₂O molecules to models of improves agreement with measured vibrational frequencies and bond lengths; 1000 ln β increases by 0.8-1.0‰. An additional hydration sphere around increases 1000 ln β by only 0.1‰.Isotopic fractionations predicted for this simple system imply that ligands present in an aqueous iron environment are potentially important drivers of fractionation, and suggest that significant fractionation effects are likely in other aqueous systems containing sulfides or organic ligands. Fractionation effects due to both speciation and redox must be considered when interpreting iron isotope fractionations in the geological record.