压力控制的圆孔扩张数值模拟分析

受沉积历史的影响,实际工程中土体的初始应力往往呈各向异性,此时传统圆孔扩张理论的假定条件不再成立,故其适用性也受到限制。借助于FLAC有限差分数值软件,建立了以压力为圆孔扩张边界的二维圆孔扩张模型,从圆孔的变形、孔周土屈服范围、圆孔扩张产生的超静孔水压力分布等方面进行分析,获得在初始应力各向异性的条件下压力控制圆孔扩张过程土体响应规律。计算分析结果表明,初始应力各向异性时,压力控制的圆孔扩张孔口径向位移、塑性区分布、超静孔隙水压力影响范围各个方向不相等;塑性区的分布具有明显的方向性,塑性区最大半径位于孔周土体初始大主应力方向上,并且其值比在相同的扩张压力作用下各向同性初始应力条件下的塑性区半径大,因此传统的初始等应力条件下位移控制的圆孔扩张理论用于分析各向异性初始应力的工程是偏于不安全的。     

全风化花岗岩抗剪强度影响因素分析

研究了香港全风化花岗岩三轴抗剪强度指标凝聚力c、内摩擦角 同微结构及成分的关系,指出微结构的特点决定了强度特点, 值主要由其石英与长石总含量和颗粒中大于0.5 mm的含量所控制,而c值的影响因素复杂性决定了其试验结果的离散性。通过研究c, 值与应变之间的关系,说明摩擦力在强度中占的比重大,并能够进一步解释c值结果的离散性大的原因。     

Numerical investigation of undrained cavity expansion in fine-grained soils

Based on the spherical cavity expansion (SCE) problem, Cudmani and Osinov (Can Geotech J 38:622–638, 2001), Osinov and Cudmani (Int J Numer Anal Method Geomech 25:473–495, 2001) developed a semi-empirical method of interpretation of CPT for coarse-grained soils (sand, gravel) using a hypoplastic constitutive model. Using a material-independent shape factor, the cone penetration resistance was related to the limit pressure required to expand a spherical cavity. The shape factor was observed to be a function of the soil state only, in particular the pressure-dependent relative density. This paper presents an analogous interpretation technique for CPT in fine-grained soils using the shape factor concept, Cavity Expansion approach, and a hypoplastic constitutive model. Relations for the shape factor and the limit pressure have been proposed based on the parameters affecting these quantities. A validation of the proposed interpretation technique with experimental results has also been performed.     

花岗岩风化土与废弃轮胎混合物力学特性研究

废旧轮胎的治理是一个世界性的难题,而将废旧轮胎应用于岩土工程加固中则为其污染治理提供了一个行之有效的手段。为了进一步研究废旧轮胎对土体的加固机制并应用到实际工程中,主要选取了全风化花岗岩砂颗粒和加工后的废旧轮胎（包括颗粒型和长条型）的混合体作为研究对象,通过一系列不同竖向压力下的一维压缩试验,详细研究不同橡胶含量配比、不同形态下的橡胶-砂混合体的受压力学特性,并创新性地探讨了橡胶颗粒对砂颗粒在压缩过程中破碎行为的影响。试验结果表明,所有橡胶-砂混合体在较高压力作用下都能收敛到一条直线,即存在唯一的标准压缩线;随着橡胶含量增加到大于20%,混合物的压缩和卸载回弹量均明显增加,而这种特性不受轮胎颗粒形态的影响。此外,轮胎橡胶含量配比越高,砂颗粒的破碎程度越小,同时,当其中砂颗粒尺寸越小时,整体破碎越少。     

全风化花岗岩全岩和粘粒中粘土矿物含量变化对比

工程实践和理论研究中常用全岩和粘粒中粘土矿物绝对和相对含量.对同一样品探求两者关系,便于数据对比,有利于工程应用.以采自香港九龙的2处边坡3个探坑中51个全风化花岗岩样品为例,作者用同一套仪器、测试方法,先后采用了颗分法测粘粒质量百分比、物理化学方法测比表面积、XRD方法测矿物成分,分别得出了全岩和粘粒中粘土矿物的绝对含量和相对含量,以及用粘粒质量百分比乘以相对含量得出的换算含量.另外还将全岩XRD矿物成分同薄片统计结果进行了相关分析.对粘土矿物绝对含量基本为20%～45%的全风化花岗岩,对比分析不同含量结果表明:全岩中的某些粘土矿物,如高岭石、蛭石的绝对含量远大于换算含量;不同样品中高岭石和蛭石的相对含量变化幅度远大于它们在全岩中绝对含量变化,两者变化呈现某种一致性;全岩中粘土矿物含量远大于粘粒(粒径<2μm和<5μm两个界限)的含量.后两者相对而言变化基本一致,差值不大;同全岩中粘土矿物含量相关性较好的是比表面积;同薄片统计结果相比,全岩XRD粘土矿物含量受对风化矿物处理不确定性的影响,结果往往偏大.     

Engineering properties of fresh and decomposed igneous rocks from Hong Kong

The influence of degree of decomposition on the strength and elasticity of fresh to highly decomposed igneous rocks in Hong Kong is described and summarized. Assessments of degree of decomposition by rock grade, rock quality designation, apparent porosity, ultra-sonic velocity, and point load index are discussed from the point of view of estimating rock behaviour. For engineering purposes a sufficiently precise measure of decomposition could be based on the point load index, and a sufficiently reliable estimate of elastic modulus could be calculated from the ultra-sonic velocity.     

花岗岩风化料弃土快速堆填过程中不排水抗剪强度评估

沿海沿江城市地下开挖产生的工程渣土含泥量大、含水率高且较松散,主要运往渣土场进行堆填处置。由于产量巨大而处置场地有限,许多渣土场在运营过程中存在堆填速度快、缺乏排水设施、超高超库容堆填等问题,容易引发堆填体失稳事故。目前对于非饱和工程渣土堆体在快速堆填过程中的失稳机制认识尚不清晰,尤其是对这一过程中的高饱和度工程渣土强度增长规律缺乏足够的认识。以深圳红坳渣土场填料——花岗岩风化料(CDG)填土为研究对象,对不同初始饱和度土样进行三轴不排水不排气等向压缩和剪切试验,结果表明:非饱和CDG填土不排水抗剪强度随围压增大呈非线性增长,增长速率与试样初始饱和度密切相关;当土样压缩后的饱和度超过0.7,不排水强度随围压的增长速率显著降低。基于有效固结应力法的原理,结合Hilf孔压公式和修正剑桥模型,提出了一种工程渣土不排水抗剪强度估算方法,并通过与试验结果对比验证了该方法对初始饱和度高于0.6的CDG填土的适用性。利用该方法确定的不排水强度cu与正应力σn的关系可应用于高饱和度工程渣土快速堆填中的稳定性分析。     

Weathering indices for rhyolitic tuff and granite in Hong Kong

A series of chemical analyses and dry density tests of rhyolitic tuff and granitic samples have been carried out. The test results have been interpreted using a newly developed theoretical weathering model for calculating a mobility index of major elements in rock and soil. It is found that this index is useful for describing changes of rock and soil during weathering and classifying the degrees of weathering. Based on the theoretical model, a new parameter called the volume index, which combines chemical and physical data, is suggested. This index appears to be a good indicator for classifying the degree of weathering in Hong Kong. A quantitative classification scheme is suggested.     

全风化花岗岩物理化学特征数值统计及指标相关性分析

广布于华南(尤其是香港)地区全风化花岗岩与地质灾害关系密切。其物化指标统计结果以及相互关系研究似很欠缺。通过对香港九龙两处边坡上部3个探坑中48个全风化花岗岩样品物理化学实验结果分析，本文给出了物理化学性质统计值，并对比表面积和阳离子交换容量等主要指标进行了相关分析。这就将物理化学指标问相关关系具体量化，揭示了它们同矿物成分间的关系，并可对化学、物理化学和矿物学实验分析结果进行校验。本文结果对分析其风化特征及其工程地质性质，有一定实际意义。     

A micromechanical experimental study of highly/completely decomposed tuff granules

In this paper, an experimental micromechanical study is presented investigating the contact mechanics and tribological behaviour of highly/completely decomposed tuff granules. The parent material was taken from two locations—named the top and bottom—from a recent landslide in Hong Kong, and in this study the tested granules were obtained from the parent material after drying and sieving processes. Basic material characterisation was conducted quantifying the particle shape, the surface roughness and the strength of a set of grains. A set of twenty-nine monotonic inter-particle shearing tests were conducted on pairs of granules taken from the top and bottom of the landslide. It was found that the granules had very high friction angles at their contacts, in general greater in comparison with other materials reported in the literature. The slightly greater inter-particle friction for the granules taken from the top of the landslide might be because of their higher roughness in comparison with the ones from the bottom. Additional experiments were conducted to investigate the normal and tangential load–displacement response of the granules subjected to cyclic loading. A good curve fitting for the normal load–displacement response could be obtained by using very low apparent Young’s moduli in the Hertzian model. In general, the decomposed tuff granules showed significant plastic response during the first normal load cycle, and this plastic behaviour continued for the subsequent third and fourth cycles. In the cyclic inter-particle shearing tests, the nonlinearity and hysteresis increased for larger cyclic displacements, but the effect of the number of shearing cycles on the energy loss was generally small. Finally, a limited discussion is presented on the applicability of a theoretical model on the tangential load–displacement behaviour of the granules.     

Structurally controlled landslides in saprolitic soils in Hong Kong

A number of large slope failures which have occurred in Hong Kong have highlighted the important influence that discontinuities in saprolitic soils can have on slope stability. Conventional stability analyses normally adopted for such soils, which assume failure through intact materials of uniform shear strength, are not appropriate if discontinuity-controlled failures can be postulated. Stress history and present-day weathering effects should also be taken into consideration in the assessment of the long-term stability of slopes in weathered rocks in tropical and subtropical regions. © Rapid Science Ltd. 1998     

Solution for spherical cavity expansion in state-dependent soils

Acta Geotechnica - This work presents a spherical cavity expansion solution aimed at linking soil constitutive behavior with quantities that bear direct engineering meanings for practicing...     

全风化花岗岩孔径分布-颗粒组成-矿物成分变化特征及指标相关性分析

孔径分布、颗粒组成和矿物成分是全风化花岗岩微观和结构特征的3个主要方面,也是决定其工程地质性质的关键因素。理论研究和实际工程中,常用大、中小和微孔隙、角砾、砂粒和粉粘粒、三大矿物（石英、长石和粘土矿物）含量等指标表征这3方面的特征。3方面指标在一定范围上变化幅度多大？数值间相关性及作为土结构模型组份因子,它们相对权重多大？通过对香港九龙两处边坡51件全风化花岗岩试样压汞测试、颗粒分析和X射线衍射（XRD）等微观结构特征分析,结果表明：两处边坡粗粒和细粒结构全风化花岗岩有明显区别,前者主要属于砾石土和砂砾土,部分为含砾土,大孔隙多,石英和粘土矿物多,而后者部分属含砾土,部分为细砂土和亚砂土,微孔隙多,长石多;两者长石和粘土矿物含量变化正好相反。借助于多因素关系矩阵法,对3方面共9个指标作相关分析发现,相关性较好的指标是：角砾和砂粒 (0.948);大孔隙和微孔隙(0.846);石英和长石(0.827);长石和粘土矿物 (0.747)。从土结构因子角度考虑,权重从大到小指标是：微孔隙、长石、粘土矿物、砂粒、角砾、大孔隙、中小孔隙、粉粘粒和石英。其分析结果可为该类土微观结构特征细化及分类提供依据,为其微结构力学研究提供基础材料。     

Heavy metal contamination of urban soils and street dusts in Hong Kong

Due to rapid urbanisation and scarcity of land, most of the urban parks and recreational areas in Hong Kong are built close to major roads or industrial areas, where they are subject to many potential pollution sources, including vehicle exhaust and industrial emissions. An extensive soil survey was conducted in urban parks of Hong Kong to study the current conditions of heavy metals contamination in soils. Soil samples and associated street dusts were collected from more than 60 parks and public amenity areas in old urban districts, industrial areas and New Towns of the territory. Soils were also sampled in the remote country parks to establish the baseline conditions. The total concentrations of heavy metals and major elements in the samples were determined. The results indicate that urban soils in Hong Kong have elevated concentrations of Cd, Cu, Pb and Zn. The parks with high metal concentrations are located in old urban commercial districts and industrial areas, indicating that the major contamination sources in these soils are traffic emissions and industrial activities. In addition, the application of Cd containing phosphate fertilizers may be an important source of Cd in urban park soils. The street dusts have highly elevated Zn concentration, particularly along the main trunk roads. The high Zn content in the street dusts may come from traffic sources, especially vehicle tyres. Selective soil and road dust samples were also analysed for potential chemical speciation by a sequential chemical extraction method. The chemical partitioning results show that Pb and Zn are mainly in the carbonate/adsorbed and Fe–Mn oxide phases, while Cu is largely associated with the organic and sulphide fractions. The high exchangeable Cd in urban soils and high concentration of Zn in street dusts need further investigation for their ecological and health implications.     

Undrained cavity expansion in anisotropic soils with isotropic and frictional destructuration

This paper proposes a semi-analytical solution of undrained cylindrical cavity expansion in anisotropic soils with both isotropic and frictional destructuration. The rigorous derivation based on the general form of the SANICLAY model with destructuration is provided following a standardized solving procedure, and the features of anisotropy and structuration are then invoked in the cavity expansion solution by adopting the non-associated hierarchical model. Cavity expansion tests in both structured and unstructured clays with various overconsolidation ratio are conducted to investigate the evolutions of effective stresses, excess pore pressure, anisotropic parameters and structuration factors during cylindrical expansion. The results show that the effective stresses at the cavity wall are lower after expansion and the cavity excess pore pressure is oppositely higher in structured clays with slightly smaller plastic regions. The evolutions of anisotropy for structured clays appear to follow similar patterns to unstructured cases, whereas the degree of anisotropy is further developed with gradual loss of inter-particle bonds. Finally, the proposed solution is applied to predict the limit pressure of pressuremeter tests in Bothkennar clay, showing its ability for interpretation of in situ testing data in natural structured clays.

     

全风化花岗岩突水通道扩展的颗粒起动流速研究

突水突泥是富水全强风化花岗岩隧道施工常见的地质灾害,地层颗粒的流失是导致突水通道扩展的关键因素,其中颗粒达到起动流速是其流失的临界条件。考虑水流冲刷和土体黏结作用,对突水通道断面颗粒进行三维受力分析,导出颗粒的临界起动条件,建立了考虑颗粒粒径、颗粒坡面位置、相对暴露度三因素的颗粒起动流速函数,并利用数值方法分析了上述三因素对起动流速的影响规律。计算分析表明:起动流速随粒径增大先减小后增大,通道断面不同坡面位置颗粒起动流速呈明显的对称性,总体上起动流速随相对暴露度的增大呈增大趋势。采用正交试验法研究了三因素对颗粒起动流速的敏感性,发现粒径对起动流速影响最为显著。同时根据断面颗粒起动最小流速标准及相对暴露度的随机性,简化颗粒坡面位置和相对暴露度两因素,导出颗粒起动流速的简化公式,最后利用室内试验和工程实例验证了该公式的合理性。     

Defining the geochemical baseline: a case of Hong Kong soils

A geochemical baseline provides the means to distinguish between the pedogenic origin and the anthropogenic origin of the trace element in the environmental compartments. We collected 271 soil samples representative of different parent rocks and soil types from the whole territory of Hong Kong and analyzed the composition of clay mineralogy and the contents of 15 chemical elements (Fe, Cd, As, etc.) for these samples. The baseline was predicted with the method of the normalization procedure combined with the relative cumulative frequency curve. The result indicated that Fe was the best reference element for the normalization procedure among the five potential reference elements (Fe, Al, Sc, Ti, and Mn), followed by Sc and Ti. A poor correlation was found between Sc, Ti, and Cu. The predicted baseline was much lower than the A-value of the Dutch List used usually in screening the polluted soil of Hong Kong, implying that the extent of heavy metal pollution might have been underestimated with respect to local lands. We also applied the cluster analysis to distinguish the geochemical associations of the trace elements due to its importance to the baseline. Approximately three major associations including the Fe–Mn-oxides related, Al oxides or Al-bearing-clay-mineralogy related and sulfide- related associations were observed from the dendrogram.     

K0固结饱和土柱孔扩张问题弹塑性分析

采用K0固结各向异性土体本构模型,将柱孔扩张后周围土体分为弹性区和塑性区,根据柱孔扩张理论和边界条件,推导出K0固结状态下饱和天然土体柱孔扩张问题弹塑性区的应力、塑性区半径以及超孔隙水压力的理论解答。同时,通过算例与修正剑桥模型解答进行对比分析,结果表明,土的不同初始固结状态对柱孔扩张后孔周围的应力和超孔隙水压力产生很大影响,采用考虑K0固结诱发各向异性土体本构模型所得到的应力和超孔隙水压力解答大于修正剑桥模型的解答,但塑性区影响半径却明显小于后者。     

Exact solution for drained spherical cavity expansion in saturated soils of finite radial extent

This study presents an exact solution for drained spherical cavity expansion subjected to constant stress and zero displacement boundary conditions in finite medium. The solution is exact as no simplification is involved in the solution procedure in the plastic region and can be solved as an initial value problem. The effect of finite radial extent on the results of cavity expanding to a certain radius is accounted for through the initial values at the elastic-plastic boundary. A critical state constitutive model with a nonassociated flow rule is adopted. The model parameters from literature are then used in generating the results for cavity expansion in infinite and finite radial extent to highlight the difference. Also, the results are presented in a way that can be used to account for the boundary effect for the interpretation of cone penetration tests conducted in calibration chambers.     

香港九龙大坑东地下蓄水方案数值研究

香港九龙大坑东地下蓄水方案(Tai Hang Tung Storage Scheme-THTSS)是香港西九龙渠道改善二期计划的一个重要组成部分,其目标是解决香港九龙繁华拥挤、人口稠密的商业中心旺角一带的洪水淹没问题。THTSS即是在经常洪水淹没区域(大坑东和界限街水渠交接处)上游足球场下面建立一个100 000 m3的地下蓄水池。本文建立了一个能处理明渠缓流和急流、封闭管道有压流、侧流堰和渠道汇合处过渡流于一体的一维水力数学模型,用1:22正态物理模型恒定流下的结果进行验证。数值模型计算了在50年一遇暴雨下,非恒定洪水在不同的侧流堰方案下的流动过程。结合物理模型试验结果,选择最佳的地下蓄水方案。计算结果表明,大坑东地下蓄水方案确实能加强旺角地区地洪水控制能力,并能通过50年一遇暴雨的洪水。