Removal of textile dyes from aqueous solution by conducting polymer modified clinoptilolite

In this work, clinoptilolite was modified with conducting polyaniline polymer and then the nanocomposite was used as an adsorbent for methyl orange (MO) as a model dye. Cations located in clinoptilolite structure like Na⁺, K⁺, Mg²⁺, Ca²⁺ were exchanged with anilinium cations and then the polymerization of anilinium cations in and outside of the clinoptilolite channels resulted in the formation of polyaniline/clinoptilolite nanocomposite. The resulted nanocomposite was used for the removal of MO from aqueous solution. The effect of various factors like contact time, concentration of dye as well as the amount of adsorbent on the removal efficiency of dye was investigated. The adsorption isotherms were investigated. It was found that the equilibrium adsorption data were well described by the Langmuir isotherm model. The kinetic studies indicated that the adsorption process was controlled by pseudo-second-order equation. High adsorption capacity and low contact time as well as the low cost of modified clinoptilolite proved that it is an efficient adsorbent for the removal of MO from aqueous solutions.     

Preparation of magnetic microgels for catalytic reduction of 4-nitrophenol and removal of methylene blue from aqueous medium

This work describes the synthesis of poly(acrylic acid) microgels and fabrication of magnetic cobalt nanoparticles in the prepared microgels. Cobalt nanoparticles were fabricated by loading the cobalt (II) ions in microgels from aqueous solution and their subsequent reduction with sodium borohydride (NaBH₄). Bare and composite microgels were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy and transmission electron microscopy. The catalytic properties of the prepared microgel composites were investigated by using them as catalyst for the reduction of 4-nitrophenol and methylene blue. The effect of temperature and catalyst dose on the rate of reduction of these toxic pollutants was investigated. The reusability of prepared catalysts was also studied for the five consecutive cycles, and an increase in catalytic activity was observed after every cycle. The prepared bare and magnetic microgels were found as very effective adsorbent for the removal of methylene blue from aqueous medium. Very rapid adsorption rate was found for the removal of methylene as its 100 mg was adsorbed on per gram of dried hydrogels in about 25 min. The effects of different parameters like amount of adsorbate and concentration of adsorbent on the adsorption process were studied. Langmuir, Freundlich and Temkin adsorption isotherms were applied, and it was found that adsorption of MB follows Freundlich model better than others. Furthermore, pseudo-first-order and pseudo-second-order kinetic models were also applied and adsorption of MB was found to abide by pseudo-second-order kinetics.     

Retention studies of chromium (VI) from aqueous solution on the surface of a novel carbonaceous material

In the present study, the retention capacity of carbonaceous material obtained from the diesel engine exhaust mufflers for Cr(VI) removal has been investigated. The physicochemical properties such as density, pH of aqueous slurry, pH at point of zero charge, ash content, moisture content, volatile matter, surface area, scanning electron microscopy and electron dispersive spectroscopy of the carbonaceous material were determined. The capacity of adsorbent for removal of Cr(VI) from aqueous solution was observed under different experimental condition like contact time, initial concentration of metal ions, pH and temperatures on the adsorption capacity of the adsorbent. Maximum adsorption of Cr(VI) ions was found at low pH. The adsorption process was found to follow second-order kinetics. The rate constant was evaluated at different temperatures along with other thermodynamic parameters like activation energy, Gibbs free energy change, enthalpy change and entropy change. Both Langmuir and Freundlich isotherms were used to describe the adsorption equilibrium of carbonaceous material at different temperatures. Langmuir isotherm shows better fit than Freundlich isotherm at given conditions. The result shows that low-cost carbonaceous material from diesel engine exhaust mufflers can be efficiently used for wastewater treatment containing Cr(VI) ions.     

Removal of cadmium (II) from aqueous solution and natural water samples using polyurethane foam/organobentonite/iron oxide nanocomposite adsorbent

A novel polyurethane foam/organobentonite/iron oxide nanocomposite adsorbent was successfully prepared via in situ polymerization of toluene diisocyanate and polyol in presence of 5 wt% organobentonite/iron oxide. The obtained nanocomposite was characterized in detail, and the results revealed that the clay layers are exfoliated and/or intercalated in the polymer matrix forming a nanocomposite structure. The application of the prepared nanocomposite for adsorption of cadmium ions from aqueous solution was tested as a function of various experimental parameters using batch procedures. Adsorptive removal of Cd(II) onto the nanocomposite attained maximum at adsorbent content 1.5 g/L, pH 6, and the equilibrium was established within 60 min. Kinetic studies showed that the experimental data fit very well to pseudo-second-order model, and the adsorption process proceeds through three steps. It was found that external liquid film and intraparticle diffusion steps deeply affect the rate of Cd²⁺ ions adsorption onto the synthesized nanocomposite. Langmuir isotherm model fitted the adsorption data better than Freundlich with a maximum adsorption capacity (q _m) for Cd(II) equal to 78 mg/g under the specified experimental conditions. The synthesized nanocomposite afforded effective extraction for Cd²⁺ ions from natural water samples and excellent reusability feature. This study declares the potential efficiency of a new clay/polymer nanocomposite as alternative for wastewater remediation.     

Adsorption of lead using a new green material obtained from Portulaca plant

In the present study the potential of a new green material obtained from Portulaca oleracea plant was investigated. The material was used without any chemical treatment to study the adsorption behavior of lead ions from aqueous solution. Various batch experiments were carried out using different experimental conditions such as pH, contact time, adsorbent concentration, and metal ion concentration to identify the optimum conditions. The influence of these parameters on the adsorption capacity was studied. Results showed the optimum initial pH for adsorption as 6. Adsorption equilibrium was reached in 120?min. The adsorption data were modeled using both the Langmuir and Freundlich classical adsorption isotherms. Results show ~78% removal of lead from aqueous solution. The kinetic data corresponded well with pseudo second-order equation. From the initial results, the green material obtained from the waste of Portulaca seems to be a potential low-cost adsorbent for removal of lead ions from water.     

Green synthesis of magnetic mesoporous silica nanocomposite and its adsorptive performance against organochlorine pesticides

Green synthesis of nanomaterials has received increasing attention as an eco-friendly technology in materials science. Here, we have used two types of extractions from green tea leaf (i.e., total extraction and tannin extraction) as reducing agents for a rapid, simple and one-step synthesis method of mesoporous silica nanoparticles/iron oxide nanocomposite based on deposition of iron oxide onto mesoporous silica nanoparticles. Mesoporous silica nanoparticles/iron oxide nanocomposite were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, energy-dispersive X-ray, vibrating sample magnetometer, N₂ adsorption and high-resolution transmission electron microscopy. Mesoporous silica nanoparticles/iron oxide nanocomposite was used as a solid adsorbent for removal of lindane pesticide from aqueous solutions. The developed system possesses the advantages of silica as core that include large surface area and advantages of iron oxide (shell) that include the capability to interact with chlorinated compounds and ability to release by using external magnetic field. UV-Vis technique was used as a simple and easy method for monitoring the removal of lindane. Effects of pH and temperature on the removal efficiency of the developed mesoporous silica nanoparticles/iron oxide nanocomposite toward lindane pesticide were also investigated. Fourier transform infrared spectroscopy, high-performance liquid chromatography and gas chromatography techniques were used to confirm the high ability of mesoporous silica nanoparticles/iron oxide nanocomposite for sensing and the capture of lindane molecules with high sorption capacity (about 99%) that could develop a new eco-friendly strategy for detection and removal of pesticide and as a promising material for water treatment.     

Biosorption of Cd(II) from synthetic wastewater using dry biofilms from biotrickling filters

Biofilms wasted from biotrickling filters was dried and used as biosorbent for Cd(II) removal from aqueous solutions. The adsorption condition and effect, adsorption isotherms and kinetics of Cd(II) removal were investigated, and the effects of competitive metal ions on Cd(II) removal were also examined. Results showed that the dry waste biofilms reached the maximum adsorption capacity of 42 mg/g of Cd(II) at 25 °C for 120 min when the initial concentration of Cd(II) and their pH were 50 mg/L and 6.0, respectively. Under these conditions, the removal efficiency of Cd(II) reached to 89.3% when the biosorbent dosage was 2.0 g/L. The Langmuir isotherm model correlated with the isotherm data better than the Freundlich isotherm model, and the pseudo-second-order model fitted the kinetic data better than the pseudo-first-order model. These results indicated that the adsorption was monolayer accompanied with chemical adsorption. In the presence of other metal ions, divalent metal ions of Ca and Zn inhibited the performance of Cd(II) biosorption significantly, while Na(I), K(I) and Fe(III) which had a higher or lower valence than Ca(II) affected slightly when containing 50 mg/L Cd(II), 0.5 g/L adsorbent dosage and pH 6.0. The analyses of scanning electron microscopy and Fourier transform infrared spectroscopy illuminated that the biosorbent had porous structures and the amide group was the majorly responsible for Cd(II) removal. Dry biofilms were novel sorbents for effective removal Cd(II), and it could be reused and recycled if necessary.     

Equilibrium studies on removal of lead (II) ions from aqueous solution by adsorption using modified red mud

In the present experimental study, solid waste was used as an adsorbent and the effectiveness of the adsorbent was increased by novel treatment methods. Red mud, acid-treated activated red mud and iron oxide-coated acid-treated activated red mud were used for the removal of lead (II). The structural and functional groups were identified to confirm the removal of lead (II) by powder X-ray diffraction and Fourier transform infrared spectroscopy analyses. The enhancement of surface area was confirmed by Brunauer–Emmett–Teller analysis. Batch adsorption experiment was also conducted, and various parameters such as the effect of adsorbent dosage, pH, contact time and initial ion concentration were analyzed and reported. Adsorption equilibrium data were investigated using Langmuir, Freundlich and Dubinin–Radushkevich isotherm models with three parameters, and the rate of reaction was examined through kinetic models. The results indicate that in particular a novel modified form of red mud, namely iron oxide-coated acid-treated activated red mud was well fitted in lead (II) removal compared with reported adsorbents. The Langmuir isotherm shows that the maximum adsorption of adsorbate per gram was greater than other adsorbents (27.02 mg/g). In Freundlich isotherm, the Freundlich constant n values lie between 1 and 10 indicate the favorable adsorption. The calculated n values for normal red mud, acid-treated activated red mud and iron oxide-coated acid-treated activated red mud were found to be 1.9, 2.1 and 2.0 respectively. The correlation coefficient value was higher and the rate of reaction follows the pseudo-second-order kinetic model.     

Insight into adsorption equilibrium,kinetics and thermodynamics of lead onto alluvial soil

In the present study, adsorption of lead (II) ions from aqueous solution by alluvial soil of Bhagirathi River was investigated under batch mode. The influence of solution pH, sorbent dose, initial lead (II) concentration, contact time, stirring rate and temperature on the removal process were investigated. The lead adsorption was favored with maximum adsorption at pH 6.0. Sorption equilibrium time was observed in 60 min. The equilibrium adsorption data were analyzed by the Freundlich, Langmuir, Dubinin–Radushkevich and Temkin adsorption isotherm models. The kinetics of lead (II) ion was discussed by pseudo first-order, pseudo second-order, intra-particle diffusion, and surface mass transfer models. It was shown that the adsorption of lead ions could be described by the pseudo second-order kinetic model. The activation energy of the adsorption process (E _a) was found to be ?38.33 kJ mol^?1 using the Arrhenius equation, indicating exothermic nature of lead adsorption onto alluvial soil. Thermodynamic parameters, such as Gibbs free energy (?G ⁰), the enthalpy (?H ⁰), and the entropy change of sorption (?S ⁰) have also been evaluated and it has been found that the adsorption process was spontaneous, feasible, and exothermic in nature. The results indicated that alluvial soil of Bhagirathi River can be used as an effective and low cost adsorbent to remove lead ions from aqueous solutions.     

Removal of Arsenic(V) from Aqueous Solutions by Lanthanum-loaded Zeolite

A new adsorption process for the removal of As（V） ion from aqueous solutions is studied in this paper using lanthanum-loaded zeolite. The removal efficiency of different adsorbents, activated alumina and activated carbon are obtained in the study for comparison. The results show that lanthanum-loaded zeolite is an effective adsorbent for the removal of As（V） from aqueous solutions. Then, the pH effect and regeneration of modified zeolite on the As（V） removing efficiency are also assessed. It functions with a wide range of pH （2-8）. After adsorption, zeolite adsorbed with As（V） ions can be regenerated successfully with 1 M NaOH. Based on the data obtained, an adsorption mechanism and the possible complex structure are tentatively presented. Compare to other adsorbents, easy availability of this adsorbent, excellent adsorption capacity, wide optimum pH range, and regeneration are expected to be utilized in practical operations.     

Single and binary adsorption of lead and cadmium ions from aqueous solution using the clay mineral beidellite

Beidellite, a low-cost, locally available and natural mineral was used as an adsorbent for the removal of lead and cadmium ions from aqueous solutions in batch experiments. The kinetics of adsorption process was tested for the pseudo first-order, pseudo second-order reaction and intra-particle diffusion models. The rate constants of adsorption for all these kinetic models were calculated. Comparison amongst the models showed that the sorption kinetics was best described by the pseudo second-order model. Langmuir and Freundlich isotherm models were applied to the experimental equilibrium data for different temperatures. The adsorption capacities (Q°) of beidellite for lead and cadmium ions were calculated from the Langmuir isotherm. It was found that adsorption capacity was in the range of 83.3–86.9 for lead and 42–45.6 mg/g for cadmium at different temperatures. Thermodynamic studies showed that the metal uptake reaction by beidellite was endothermic in nature. Binary metal adsorption studies were also conducted to investigate the interactions and competitive effects in binary adsorption process. Based on the optimum parameters found, beidellite can be used as adsorbent for metal removal processes.     

A novel adsorbent for heavy metal remediation in aqueous environments

The objective of this study was to investigate the possibility of using maize tassel as an alternative adsorbent for the removal of chromium (VI) and cadmium (II) ions from aqueous solutions. The effect of pH, solution temperature, contact time, initial metal ion concentration and adsorbent dose on the adsorption of chromium (VI) and cadmium (II) by tassel was investigated using batch methods. Adsorption for both chromium (VI) and cadmium (II) was found to be highly pH dependent compared to the other parameters investigated. Obtained results gave an adsorption capacity of 79.1 % for chromium (VI) at pH 2, exposure time of 1h at 25 °C. Maximum capacity of cadmium of 88 % was obtained in the pH range of 5-6 at 25 °C after exposure time of 1 h. The adsorption capacities of tassel for both chromium (VI) and cadmium (II) were found to be comparable to those of other commercial adsorbents currently in use for the removal of heavy metals from aqueous wastes. These results have demonstrated the immense potential of maize tassel as an alternative adsorbent for toxic metal ions remediation in polluted water and wastewater.     

Removal of lead from aqueous solution using low cost abundantly available adsorbents

The removal of poisonous Pb (II) from wastewater by different low-cost abundant adsorbents was investigated. Rice husks, maize cobs and sawdust, were used at different adsorbent/metal ion ratios. The influence of pH, contact time, metal concentration, adsorbent concentration on the selectivity and sensitivity of the removal process was investigated. The adsorption efficiencies were found to be pH dependent, increasing by increasing the solution pH in the range from 2.5 to 6.5. The equilibrium time was attained after 120 min and the maximum removal percentage was achieved at an adsorbent loading weight of 1.5 gm. The equilibrium adsorption capacity of adsorbents used for lead were measured and extrapolated using linear Freundlich, Langmuir and Temkin isotherms and the experimental data were found to fit the Temkin isotherm model.     

Hydrothermal synthesis of hydroxy sodalite from fly ash for the removal of lead ions from water

Zeolites are known to possess valuable physiochemical properties such as adsorption, cation exchange, molecular sieving, and catalysis. In addition, zeolites are highly selective scavengers of a variety of heavy metals from liquid effluents through the process of ion exchange. The present study was performed to hydrothermally synthesize Na₈[AlSiO₄]₆(OH)₂·2H₂O (also known as hydroxy sodalite hydrate). Due to its small aperture size, this material can be an ideal candidate for the separation of small molecules and ions from aquatic and gas mixtures. Synthetic zeolites offer many advantages over natural zeolites, such as higher ion affinity and adsorption capacity. Batch adsorption isotherm studies were conducted to evaluate the obtained adsorbent for the lead ion removal from aqueous media. Modeling lead ion adsorption using Langmuir and Freundlich isotherm expressions determined the capacity of the adsorbent. A removal efficiency of 98.1 % in a 3.0 g/l adsorbent/solution mixture with a maximum adsorption capacity of 153.8 mg/g was obtained. One potential application of the synthesized zeolite is for the lead removal in point-of-use treatment devices.     

Nettle ash as a low cost adsorbent for the removal of nickel and cadmium from wastewater

This study was focused on nettle ash as an alternative adsorbent for the removal of nickel (II) and cadmium (II) from wastewater. Batch experiments were conducted to determine the factors affecting adsorption of nickel (II) and cadmium (II). The adsorption process is affected by various parameters such as contact time, solution pH and adsorbent dose. The optimum pH required for maximum adsorption was found to be 6. The experimental data were tested using Langmuir, Freundlich and Tempkin equations. The data were fitted well to the Langmuir isotherm with monolayer adsorption capacity of 192.3 and 142.8 mg/g for nickel and cadmium, respectively. The adsorption kinetics were best described by the pseudo second order model. The cost of removal is expected to be quite low, as the adsorbent is cheap and easily available in large quantities. The present study showed that nettle ash was capable of removing nickel and cadmium ions from aqueous solution.     

Significance of co-immobilized activated carbon and Bacillus subtilis on removal of Cr(VI) from aqueous solutions

Batch sorption system using co-immobilized (activated carbon and Bacillus subtilis) beads as adsorbent was investigated to remove Cr(VI) from aqueous solution. Fourier transform infrared spectroscopy analysis showed the functional groups of both bacteria and activated carbon in co-immobilized beads. Experiments were carried out as a function of contact time (5–300 min), initial metal concentration (50–200 mg L^?1), pH (2–8), and adsorbent dose (0.2–1 g L^?1). The maximum percentage of removal was found to be 99 %. Langmuir model showed satisfactory fit to the equilibrium adsorption data of co-immobilized beads. The kinetics of the adsorption followed pseudo-second-order rate expression, which demonstrates that chemisorption plays a significant role in the adsorption mechanism. The significant shift in the Fourier transform infrared spectroscopy peaks and a Cr peak in the scanning electron microscope–energy dispersive spectroscopy spectra further confirmed the adsorption. The results indicate that co-immobilized beads can be used as an effective adsorbent for the removal of Cr(VI) from the aqueous solution.     

Dye removal from aqueous solutions using novel nanocomposite hydrogel derived from sodium montmorillonite nanoclay and modified starch

A novel nanocomposite hydrogels (NCHs)-based polysaccharide was synthesized by incorporating Na-montmorillonite (NaMMT) nanoparticles (NPs) into poly acrylic acid and polyacrylamide grafted onto starch [P(AA–AAm)-g-starch] hydrogel. The conditions applied in this synthesis were optimized using the Taguchi orthogonal experimental design method. The characterization of NaMMT NPs/P(AA–AAm)-g-starch NCH was performed by Fourier transform infrared, thermogravimetric analysis, scanning electron microscopy/energy-dispersive X-ray, and atomic force microscopy analyses. The resulting optimized NCH showed improved pH-dependent swelling and enhanced safranin adsorption capacity compared to pure hydrogel and NaMMT NPs. Its adsorption process could be described very well by pseudo-second-order and Elovich kinetic models. The adsorption isotherm was followed by Freundlich isotherm models. The conclusion confirms the prospect of NCH as an effective adsorbent for the adsorption of dyes from aqueous solutions.     

Adsorptive separation of Pb(II) and Cu(II) from aqueous solutions using as-prepared carboxymethylated waste Lyocell fiber

Adsorptive separation of Pb(II) and Cu(II) using modified waste Lyocell fiber adsorbent was investigated in this research. The waste Lyocell fiber was functionalized through carboxymethylation of the hydroxyl moieties using sodium chloroacetate as modifying agent and was crosslinked with epichlorohydrin to provide water stability. The maximum equilibrium batch uptake in single metal system was 353.45 mg/g for Pb(II) and 98.33 mg/g for Cu(II), according to the Langmuir isotherm model. The adsorption rates were very fast and reached equilibrium within 3 and 5?10 min for Cu(II) and Pb(II), respectively. In competitive binary metal system, the uptake of Cu(II) largely decreased to 38.40 mg/g, and Pb(II) selectivity was observed. Elemental and functional characterization suggested that the adsorption proceeded by ion exchange between the adsorbent and metal ions. In a flow-through column system, adsorption followed by desorption aided in effectively eluting ~260 mg of Pb(II) (out of ~300 mg total adsorbed) from the Pb(II)–Cu(II) binary solution. Finally, the adsorbent was very effective in four successive adsorption–desorption cycles with over 99 % uptake and 94 % desorption efficiencies. The present study may provide an alternative option for waste fiber recycling and could be useful in recovering heavy metal ions from aqueous sources to complement their depleting reserves.     

Biosorption of Cu(II) and Pb(II) from aqueous solutions by chemically modified spent coffee grains

In this research, spent coffee grains were modified with citric acid solutions (0.1 and 0.6 M) to increase the quantity of carboxylic groups improving its metal adsorption capacity. Added functional groups on modified and non-modified spent coffee grains were identified and quantified by attenuated total reflection Fourier transform infrared analyses and potentiometric titrations, respectively. These adsorbents were used for the removal of lead (II) and copper (II) from aqueous solutions at 30 °C and different pH in batch systems. In addition, adsorption–desorption experiments were conducted to evaluate the possibility of re-using the modified adsorbent. Potentiometric titrations data reveal that the quantity of carboxylic groups was increased from 0.47 to 2.2 mmol/g when spent coffee grains were modified with 0.1 and 0.6 M citric acid. Spent coffee grains treated with 0.6 M citric acid, achieved a maximum adsorption capacity of 0.77 and 1.53 mmol/g for lead (II) and copper (II), respectively, whereas non-modified spent coffee grains only reached 0.24 and 0.19 mmol/g for lead (II) and copper (II), respectively. Desorption of lead (II) and copper (II) achieved around 70 % using 0.1 N HCl for non-modified and modified spent coffee grains with 0.6 M citric acid. It is suggested that lead (II) and copper (II) species were adsorbed mainly on the carboxylic groups of modified spent coffee grains and these metals may be exchanged for hydrogen and calcium (II) ions during adsorption on non-modified spent coffee grains. Finally, the adsorption equilibrium was reached after 400 min for modified spent coffee grains with 0.6 M citric acid. Modified spent coffee grains are a promising option for removing metal cations from aqueous solutions due to its low cost and high adsorption capacity (about 10 times higher than the activated carbons).     

Ultrafast removal of heavy metals by tin oxide nanowires as new adsorbents in solid-phase extraction technique

In the present research, the removal of lead(II) and copper(II) from aqueous solutions is studied, using SnO₂ nanowires as new adsorbent on solid-phase extraction disk and compared with pine core and buttonwood as biosorbents. Batch adsorption experiments were performed as a function of pH, adsorption time, solute concentration and adsorbent dose for biosorbents. Also, the pH, transfer rate of solution and metal concentration were selected as experimental parameters for the removal of heavy metals by SnO₂ nanowires. All of the parameters were optimized by experimental design method for sorbents. The experimental equilibrium adsorption data are tested for the Langmuir and Freundlich equations. Results indicate the following order to fit the isotherms: Langmuir > Freundlich, in case of lead and copper ions. The removal of Cu(II) and Pb(II) was performed by selected sorbents in the presence of interferences ions. This led to no remarkable decrease in the removal efficiency of SnO₂ nanowires. Using the SnO₂ nanowires in the wastewater treatment indicated 96.8 and 85.28% removal efficiency in only 7 min for Pb(II) and Cu(II), respectively. SnO₂ nanowires were found as reusable sorbent. Therefore, SnO₂ nanowires have a good potential for application in environmental protection.