Cu (II) removal intensification using Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles under inert gas and magnetic field in a microchannel

In the present study, Cu (II) ions removal from aqueous solution was intensified by exciting magnetic nanoparticles under inert gas, magnetic field and combination of these two mixing methods in a T-type microchannel. The flow patterns and liquid–liquid two-phase mass transfer were studied in three different magnet distances from mixing channel (3, 6 and 10 mm) and also in the presence of different inert gas flow rates (1, 3 and 5 mL/min). Depending on the mixing method and the flow rate of both phases, several distinct flow patterns were observed including slugs, droplet, parallel and dispersed flows. The performances of mixing techniques for mass transfer enhancement based on relative removal efficiency ratio (λ) and mass transfer coefficient ratio (γ) were compared with simple layout (without nanoparticles, magnetic field and inert gas). The results showed that simultaneous using of inert gas and magnetic field can drive the nanoparticles as mixer. Liquid–liquid mass transfer with 27–62% enhancement in E and 235–285% in K _L a compared with plain one was observed.     

Low-temperature heat capacities of MgAl<Subscript>2</Subscript>O<Subscript>4</Subscript> and spinels of the MgCr<Subscript>2</Subscript>O<Subscript>4</Subscript>–MgAl<Subscript>2</Subscript>O<Subscript>4</Subscript> solid solution

We present results from low-temperature heat capacity measurements of spinels along the solid solution between MgAl₂O₄ and MgCr₂O₄. The data also include new low-temperature heat capacity measurements for MgAl₂O₄ spinel. Heat capacities were measured between 1.5 and 300 K, and thermochemical functions were derived from the results. No heat capacity anomaly was observed for MgAl₂O₄ spinel; however, we observe a low-temperature heat capacity anomaly for Cr-bearing spinels at temperatures below 15 K. From our data we calculate standard entropies (298.15 K) for Mg(Cr,Al)₂O₄ spinels. We suggest a standard entropy for MgAl₂O₄ of 80.9 ± 0.6 J mol⁻¹ K⁻¹. For the solid solution between MgAl₂O₄ and MgCr₂O₄, we observe a linear increase of the standard entropies from 80.9 J mol⁻¹ K⁻¹ for MgAl₂O₄ to 118.3 J mol⁻¹ K⁻¹ for MgCr₂O₄.     

Structure of magnetite (Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>) above the Curie temperature: a cation ordering study

A pristine magnetite (Fe₃O₄) specimen was studied by means of Neutron Powder Diffraction in the 273–1,073 K temperature range, in order to characterize its structural and magnetic behavior at high temperatures. An accurate analysis of the collected data allowed the understanding of the behavior of the main structural and magnetic features of magnetite as a function of temperature. The magnetic moments of both tetrahedral and octahedral sites were extracted by means of magnetic diffraction up to the Curie temperature (between 773 and 873 K). A change in the thermal expansion coefficient around the Curie temperature together with an increase in the oxygen coordinate value above 700 K can be observed, both features being the result of a change in the thermal expansion of the tetrahedral site. This anomaly is not related to the magnetic transition but can be explained with an intervened cation reordering, as magnetite gradually transforms from a disordered configuration into a partially ordered one. Based on a simple model which takes into account the cation-oxygen bond length, the degree of order as a function of temperature and consequently the enthalpy and entropy of the reordering process were determined. The refined values are ΔH⁰ = −23.2(1.7) kJ mol⁻¹ and ΔS⁰ = −16(2) J K⁻¹ mol⁻¹. These results are in perfect agreement with values reported in literature (Mack et al. in Solid State Ion 135(1–4):625–630, 2000; Wu and Mason in J Am Ceramic Soc 64(9):520–522, 1981).     

Atomistic model of diopside-K-jadeite (CaMgSi<Subscript>2</Subscript>O<Subscript>6</Subscript>-KAlSi<Subscript>2</Subscript>O<Subscript>6</Subscript>) solid solution

Atomistic model was proposed to describe the thermodynamics of mixing in the diopside-K-jadeite solid solution (CaMgSi₂O6-KAlSi₂O₆). The simulations were based on minimization of the lattice energies of 800 structures within a 2 × 2 × 4 supercell of C2/c diopside with the compositions between CaMgSi₂O₆ and KAlSi₂O₆ and with variable degrees of order/disorder in the arrangement of Ca/K cations in M2 site and Mg/Al in Ml site. The energy minimization was performed with the help of a force-field model. The results of the calculations were used to define a generalized Ising model, which included 37 pair interaction parameters. Isotherms of the enthalpy of mixing within the range of 273–2023 K were calculated with a Monte Carlo algorithm, while the Gibbs free energies of mixing were obtained by thermodynamic integration of the enthalpies of mixing. The calculated T-X diagram for the system CaMgSi₂O₆-KAlSi₂O₆ at temperatures below 1000 K shows several miscibility gaps, which are separated by intervals of stability of intermediate ordered compounds. At temperatures above 1000 K a homogeneous solid solution is formed. The standard thermodynamic properties of K-jadeite (KAlSi₂O₆) evaluated from quantum mechanical calculations were used to determine location of several mineral reactions with the participation of the diopside-K-jadeite solid solution. The results of the simulations suggest that the low content of KalSi₂O₆ in natural clinopyroxenes is not related to crystal chemical factors preventing isomorphism, but is determined by relatively high standard enthalpy of this end member.     

In situ high-temperature X-ray and neutron powder diffraction study of cation partitioning in synthetic Mg(Fe<Subscript>0.5</Subscript>Al<Subscript>0.5</Subscript>)<Subscript>2</Subscript>O<Subscript>4</Subscript> spinel

The intra-crystalline cation partitioning over T- and M-sites in a synthetic Mg(Fe,Al)₂O₄ spinel sample has been determined as a function of temperature by Rietveld structure refinements from powder diffraction data, combining in situ high-temperature neutron powder diffraction (NPD; POLARIS diffractometer, at ISIS, Rutherford Appleton Laboratory, UK), to determine the Mg and Al occupancy factors, with in situ high-temperature X-ray powder diffraction, to fix the Fe³⁺ distribution. The results obtained agree with a two-stage reaction, in which an initial exchange between Fe³⁺ and Mg, the former leaving and the latter entering tetrahedral sites, is successively followed by a rearrangement involving also Al. The measured cation distribution has then been compared and discussed with that calculated by the Maximum Configuration Entropy principle, for which only NPD patterns have been used. The cation partitioning has finally been interpreted in the light of the configuration model of O’Neill and Navrotsky.     

Atomistic simulation of the structure and segregation to the (0001) and surfaces of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>

The segregation of ten isovalent impurities (Al³⁺ Cr³⁺, Eu³⁺, Gd³⁺, Ho³⁺, La³⁺, Lu³⁺, Nd³⁺, Tb³⁺, Y³⁺) to the and the (0001) surfaces of haematite (-Fe₂O₃) have been studied using atomistic simulation where the forces between the atoms are modelled using the Born model of solids. Segregation is found to be energetically favoured in virtually every case. The results for the surface show that the most favourable impurity surface concentration is 33.33%. The (0001) surface has two possible terminations, one terminated by iron atoms and the other by oxygen. No minimum is calculated for the Fe termination of the (0001) surface at low temperatures, but when the effect of raising the temperature is considered, an energy minimum is found, also at 33.33% impurity coverage. In contrast, the O terminated (0001) surface has a minimum in the segregation energy for between 16.67 and 33.33% depending on the cation being considered.     

Adsorption behaviors of Cd^2＋ on Fe2O3/MnO2 and the effects of coexisting ions under alkaline conditions

This study describes the adsorption features of cadmium on Fe2O3 and MnO2 in alkaline saline conditions. The adsorption reached equilibrium in 6 hours under alkaline conditions. The absorption of cadmium on Fe2O3 and MnO2 was consistent with Freundlich absorption isotherms, and the corresponding adsorption capacities were 16.3 and 16.7 mg·g-1, respectively. Moreover, the adsorption quantity of cadmium on Fe2O3 and MnO2 rose with increasing pH from acidic to neutral, and reached the maximum at pH= 9. The coexisting chlorides reduced the adsorption capacity of Fe2O3 and MnO2. The influence intensities of different cations follow the order of CaCl2>>KCl>NaCl. However, the influence of sodium salts on the capacities of Fe2O3 and MnO2 to adsorb cadmium appeared more complicated: the relatively low concentrations of sodium salts could reduce the adsorption capacity; with increasing concentrations of sodium salts, e.g. NaCl and NaNO3. The adsorption capacity decreased continually. Moreover, due to the competition adsorption and precipitation effects, the adsorption capabilities of Na2CO3, NaH2PO4 and Na2HSO4 could also be reduced and cadmium concentrations in the solution were reduced as well.     

Thermodynamics of mixing in diopside–jadeite,CaMgSi<Subscript>2</Subscript>O<Subscript>6</Subscript>–NaAlSi<Subscript>2</Subscript>O<Subscript>6</Subscript>, solid solution from static lattice energy calculations

Static lattice energy calculations (SLEC), based on empirical interatomic potentials, have been performed for a set of 800 different structures in a 2 × 2 × 4 supercell of C2/c diopside with compositions between diopside and jadeite, and with different states of order of the exchangeable Na/Ca and Mg/Al cations. Excess static energies of these structures have been cluster expanded in a basis set of 37 pair-interaction parameters. These parameters have been used to constrain Monte Carlo simulations of temperature-dependent properties in the range of 273–2,023 K and to calculate a temperature–composition phase diagram. The simulations predict the order–disorder transition in omphacite at 1,150 ± 20°C in good agreement with the experimental data of Carpenter (Mineral Petrol 78:433–440, 1981). The stronger ordering of Mg/Al within the M1 site than of Ca/Na in the M2 site is attributed to the shorter M1–M1 nearest-neighbor distance, and, consequently, the stronger ordering force. The comparison of the simulated relationship between the order parameters corresponding to M1 and M2 sites with the X-ray refinement data on natural omphacites (Boffa Ballaran et al. in Am Mineral 83:419–433, 1998) suggests that the cation ordering becomes kinetically ineffective at about 600°C.     

The nature of blue luminescence from natural benitoite BaTiSi<Subscript>3</Subscript>O<Subscript>9</Subscript>

It is proved that blue luminescence from benitoite is connected with intrinsic luminescence centers, namely isolated TiO₆ octahedra. The metastable level ³T_1u is the emitting level at low temperatures with a long decay time of 1.1 ms. At higher temperatures an energy level with higher radiation probability must be involved in the emission process, and this level is situated at 0.06 eV higher than the lowest level. These two levels may be connected with ³T_1u level splitting or with closely spaced ³T_1u and ³T_2u levels. Decay time shortening and thermal quenching are connected with nonradiative decay within the TiO₆ luminescence center, while energy migration does not take place at least up to room temperature.     

Thermal expansion of new arsenate minerals,bradaczekite, NaCu<Subscript>4</Subscript>(AsO<Subscript>4</Subscript>)<Subscript>3</Subscript>, and urusovite,Cu(AsAlO<Subscript>5</Subscript>)

Thermal behavior of two new exhalation copper-bearing minerals, bradaczekite and urusovite, from the Great Tolbachik Fissure Eruption (1975–1976, Kamchatka Peninsula, Russia) has been studied by X-ray thermal analysis within the range 20–700°C in air. The following major values of the thermal expansion tensor have been calculated for urusovite: α₁₁ = 10, α₂₂ = α_b = 7, α₃₃ = 4, α_V = 21 × 10⁻⁶°C⁻¹, μ = c∧α₃₃ = 49° and bradaczekite: α_11aver = 23, α₂₂ = 8, α_33aver = 6 × 10⁻⁶°C⁻¹, μ(c∧α₃₃) = 73°. The sharp anisotropy of thermal deformations of these minerals, absences of phase transitions, and stability of the minerals in the selected temperature range corresponding to conditions of their formation and alteration during the posteruption period of the volcanic activity are established.     

First-principles simulation of high-pressure polymorphs in MgAl<Subscript>2</Subscript>O<Subscript>4</Subscript>

We have used density functional theory to investigate the stability of MgAl₂O₄ polymorphs under pressure. Our results can reasonably explain the transition sequence of MgAl₂O₄ polymorphs observed in previous experiments. The spinel phase (stable at ambient conditions) dissociates into periclase and corundum at 14 GPa. With increasing pressure, a phase change from the two oxides to a calcium-ferrite phase occurs, and finally transforms to a calcium-titanate phase at 68 GPa. The calcium-titanate phase is stable up to at least 150 GPa, and we did not observe a stability field for a hexagonal phase or periclase + Rh₂O₃(II)-type Al₂O₃. The bulk moduli of the phases calculated in this study are in good agreement with those measured in high-pressure experiments. Our results differ from those of a previous study using similar methods. We attribute this inconsistency to an incomplete optimization of a cell shape and ionic positions at high pressures in the previous calculations.     

Elasticity and equation of state of Li<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript>

A single crystal X-ray diffraction study on lithium tetraborate Li₂B₄O₇ (diomignite, space group I4₁ cd) has been performed under pressure up to 8.3 GPa. No phase transitions were found in the pressure range investigated, and hence the pressure evolution of the unit-cell volume of the I4₁ cd structure has been described using a third-order Birch–Murnaghan equation of state (BM-EoS) with the following parameters: V ₀  = 923.21(6) ų, K ₀  = 45.6(6) GPa, and K′ = 7.3(3). A linearized BM-EoS was fitted to the axial compressibilities resulting in the following parameters a ₀  = 9.4747(3) Å, K _0a  = 73.3(9) GPa, K′ _a  = 5.1(3) and c ₀  = 10.2838(4) Å, K _0c  = 24.6(3) GPa, K′ _c  = 7.5(2) for the a and c axes, respectively. The elastic anisotropy of Li₂B₄O₇ is very large with the zero-pressure compressibility ratio β _0c /β _0a  = 3.0(1). The large elastic anisotropy is consistent with the crystal structure: A three-dimensional arrangement of relatively rigid tetraborate groups [B₄O₇]²⁻ forms channels occupied by lithium along the polar c–axis, and hence compression along the c axis requires the shrinkage of the lithium channels, whereas compression in the a direction depends mainly on the contraction of the most rigid [B₄O₇]²⁻ units. Finally, the isothermal bulk modulus obtained in this work is in general agreement with that derived from ultrasonic (Adachi et al. in Proceedings-IEEE Ultrasonic Symposium, 228–232, 1985; Shorrocks et al. in Proceedings-IEEE Ultrasonic Symposium, 337–340, 1981) and Brillouin scattering measurements (Takagi et al. in Ferroelectrics, 137:337–342, 1992).     

The crystal structure of alumoklyuchevskite,K<Subscript>3</Subscript>Cu<Subscript>3</Subscript>AlO<Subscript>2</Subscript>(SO<Subscript>4</Subscript>)<Subscript>4</Subscript>

The crystal structure of the unstable mineral alumoklyuchevskite K₃Cu₃AlO₂(SO₄)₄ [monoclinic, I2, a = 18.772(7), b = 4.967(2), c = 18.468(7) Å, β = 101.66(1)°, V = 1686(1) Å] was refined to R ₁ = 0.131 for 2450 unique reflections with F ≥ 4σF _hkl. The structure is based on oxocentered tetrahedrons (OAlCu ₃ ⁷⁺ ) linked into chains via edges. Each chain is surrounded by SO₄ tetrahedrons forming a structural complex. Each complex is elongated along the b axis. This type of crystal structure was also found in other fumarole minerals of the Great Tolbachik Fissure Eruption (GTFE, Kamchatka Peninsula, Russia, 1975–1976), klyuchevskite, K₃Cu₃Fe³⁺O₂(SO₄)₄; and piypite, K₂Cu₂O(SO₄)₂.     

Calorimetric study on high-pressure transitions in KAlSi<Subscript>3</Subscript>O<Subscript>8</Subscript>

KAlSi₃O₈ sanidine dissociates into a mixture of K₂Si₄O₉ wadeite, Al₂SiO₅ kyanite and SiO₂ coesite, which further recombine into KAlSi₃O₈ hollandite with increasing pressure. Enthalpies of KAlSi₃O₈ sanidine and hollandite, K₂Si₄O₉ wadeite and Al₂SiO₅ kyanite were measured by high-temperature solution calorimetry. Using the data, enthalpies of transitions at 298 K were obtained as 65.1 ± 7.4 kJ mol^–1 for sanidine wadeite + kyanite + coesite and 99.3 ± 3.6 kJ mol^–1 for wadeite + kyanite + coesite hollandite. The isobaric heat capacity of KAlSi₃O₈ hollandite was measured at 160–700 K by differential scanning calorimetry, and was also calculated using the Kieffer model. Combination of both the results yielded a heat-capacity equation of KAlSi₃O₈ hollandite above 298 K as C_p=3.896 × 10²–1.823 × 10³T^–0.5–1.293 × 10⁷T^–2+1.631 × 10⁹T^–3 (C_p in J mol^–1 K^–1, T in K). The equilibrium transition boundaries were calculated using these new data on the transition enthalpies and heat capacity. The calculated transition boundaries are in general agreement with the phase relations experimentally determined previously. The calculated boundary for wadeite + kyanite + coesite hollandite intersects with the coesite–stishovite transition boundary, resulting in a stability field of the assemblage of wadeite + kyanite + stishovite below about 1273 K at about 8 GPa. Some phase–equilibrium experiments in the present study confirmed that sanidine transforms directly to wadeite + kyanite + coesite at 1373 K at about 6.3 GPa, without an intervening stability field of KAlSiO₄ kalsilite + coesite which was previously suggested. The transition boundaries in KAlSi₃O₈ determined in this study put some constraints on the stability range of KAlSi₃O₈ hollandite in the mantle and that of sanidine inclusions in kimberlitic diamonds.     

Thermodynamic properties,low-temperature heat-capacity anomalies,and single-crystal X-ray refinement of hydronium jarosite, (H<Subscript>3</Subscript>O)Fe<Subscript>3</Subscript>(SO<Subscript>4</Subscript>)<Subscript>2</Subscript>(OH)<Subscript>6</Subscript>

Crystals of hydronium jarosite were synthesized by hydrothermal treatment of Fe(III)–SO₄ solutions. Single-crystal XRD refinement with R₁=0.0232 for the unique observed reflections (|F_o| > 4_F) and wR₂=0.0451 for all data gave a=7.3559(8) Å, c=17.019(3) Å, V^o=160.11(4) cm³, and fractional positions for all atoms except the H in the H₃O groups. The chemical composition of this sample is described by the formula (H₃O)_0.91Fe_2.91(SO₄)₂[(OH)_5.64(H₂O)_0.18]. The enthalpy of formation (H^o_f) is –3694.5 ± 4.6 kJ mol^–1, calculated from acid (5.0 N HCl) solution calorimetry data for hydronium jarosite, -FeOOH, MgO, H₂O, and -MgSO₄. The entropy at standard temperature and pressure (S^o) is 438.9±0.7 J mol^–1 K^–1, calculated from adiabatic and semi-adiabatic calorimetry data. The heat capacity (C_p) data between 273 and 400 K were fitted to a Maier-Kelley polynomial C_p(T in K)=280.6 + 0.6149T–3199700T^–2. The Gibbs free energy of formation is –3162.2 ± 4.6 kJ mol^–1. Speciation and activity calculations for Fe(III)–SO₄ solutions show that these new thermodynamic data reproduce the results of solubility experiments with hydronium jarosite. A spin-glass freezing transition was manifested as a broad anomaly in the C_p data, and as a broad maximum in the zero-field-cooled magnetic susceptibility data at 16.5 K. Another anomaly in C_p, below 0.7 K, has been tentatively attributed to spin cluster tunneling. A set of thermodynamic values for an ideal composition end member (H₃O)Fe₃(SO₄)₂(OH)₆ was estimated: G^o_f= –3226.4 ± 4.6 kJ mol^–1, H^o_f=–3770.2 ± 4.6 kJ mol^–1, S^o=448.2 ± 0.7 J mol^–1 K^–1, C_p (T in K)=287.2 + 0.6281T–3286000T^–2 (between 273 and 400 K).     

Solid solution behaviour of CaSiO<Subscript>3</Subscript> and MgSiO<Subscript>3</Subscript> perovskites

Using density functional simulations within the generalized gradient approximation and projector-augmented wave method together with thermodynamic modelling, the reciprocal solubilities of MgSiO₃ and CaSiO₃ perovskites were calculated for pressures and temperatures of the Earth’s lower mantle from 25 to 100 GPa and 0 to 6,000 K, respectively. The solubility of Ca in MgSiO₃ at conditions along a mantle adiabat is found to be less than 0.02 atoms per formula unit. The solubility of Mg in CaSiO₃ is even lower, and most important, the extent of solid solution decreases with pressure. To dissolve CaSiO₃ perovskite completely in MgSiO₃ perovskite, a solubility of 7.8 or 2.3 mol% would be necessary for a fertile pyrolytic or depleted harzburgitic mantle, respectively. Thus, for any reasonable geotherm, two separate perovskites will be present in fertile mantle, suggesting that Ca-perovskite will be residual to low degree melting throughout the entire mantle. At the solidus, CaSiO₃ perovskite might completely dissolve in MgSiO₃ perovskite only in a depleted mantle with <1.25 wt% CaO. These implications may be modified if Ca solubility in MgSiO₃ is increased by other major mantle constituents such as Fe and Al.     

Low-temperature behaviour of ammonium ion in buddingtonite [N(D/H)<Subscript>4</Subscript>AlSi<Subscript>3</Subscript>O<Subscript>8</Subscript>] from neutron powder diffraction

The structural response of buddingtonite [N(D/H)₄AlSi₃O₈] on cooling has been studied by neutron diffraction. Data have been collected from 280 K down to 11 K, and the crystal structure refined using the Rietveld method. Rigid-body constraints were applied to the ammonium ion to explore the structural properties of ammonium in the M-site cavities at low-temperature. Low-temperature saturation is observed for almost all the lattice parameters. From the present in situ low-temperature neutron diffraction studies, there is no strong evidence of orientational order–disorder of the ammonium ions in buddingtonite.     

High-pressure Raman studies and heat capacity measurements on the MgSiO<Subscript>3</Subscript> analogue CaIr<Subscript>0.5</Subscript>Pt<Subscript>0.5</Subscript>O<Subscript>3</Subscript>

Raman spectroscopy and heat capacity measurements have been used to study the post-perovskite phase of CaIr_0.5Pt_0.5O₃, recovered from synthesis at a pressure of 15 GPa. Laser heating CaIr_0.5Pt_0.5O₃ to 1,900 K at 60 GPa produces a new perovskite phase which is not recoverable and reverts to the post-perovskite polymorph between 20 and 9 GPa on decompression. This implies that Pt-rich CaIr_1−xPt_xO₃ perovskites including the end member CaPtO₃ cannot easily be recovered to ambient pressure from high P–T synthesis. We estimate an increase in the thermodynamic Grüneisen parameter across the post-perovskite to perovskite transition of 34%, of similar magnitude to those for (Mg,Fe)SiO₃ and MgGeO₃, suggesting that CaIr_0.5Pt_0.5O₃ is a promising analogue for experimental studies of the competition in energetics between perovskite and post-perovskite phases of magnesium silicates in Earth’s lowermost mantle. Low-temperature heat capacity measurements show that CaIrO₃ has a significant Sommerfeld coefficient of 11.7 mJ/mol K² and an entropy change of only 1.1% of Rln2 at the 108 K Curie transition, consistent with the near-itinerant electron magnetism. Heat capacity results for post-perovskite CaIr_0.5Rh_0.5O₃ are also reported.     

Stabilities of NAL and Ca-ferrite-type phases on the join NaAlSiO<Subscript>4</Subscript>-MgAl<Subscript>2</Subscript>O<Subscript>4</Subscript> at high pressure

Stabilities of hexagonal new aluminous (NAL) phase and Ca-ferrite-type (CF) phase were investigated on the join NaAlSiO₄-MgAl₂O₄ in a pressure range from 23 to 58 GPa at approximately constant temperature of 1,850 K, on the basis of in situ synchrotron X-ray diffraction measurements in a laser-heated diamond-anvil cell. The results show that NAL is formed as a single phase up to 34 GPa, NAL + CF between 34 and 43 GPa, and only CF at higher pressures in 40%NaAlSiO₄-60%MgAl₂O₄ bulk composition. On the other hand, both NAL and CF coexist below 38 and 36 GPa, and only CF was obtained at higher pressures in 60%NaAlSiO₄-40%MgAl₂O₄ and 20%NaAlSiO₄-80%MgAl₂O₄ composition, respectively. These results indicate that NAL appears only up to 46 GPa at 1,850 K, and CF forms continuous solid solution at higher pressures on the join NaAlSiO₄-MgAl₂O₄. NAL has limited stability in subducted mid-oceanic ridge basalt crust in the Earth’s lower mantle and undergoes a phase transition to CF in deeper levels.