In situ formation of AgNPs on <Emphasis Type="Italic">S. cerevisiae</Emphasis> surface as bionanocomposites for bacteria killing and heavy metal removal

Novel bionanocomposites, S. cerevisiae–AgNPs, were synthesized by in situ formation of AgNPs on S. cerevisiae surface using fulvic acids as reductants under simulated sunlight. S. cerevisiae–AgNPs were characterized using UV–Vis spectroscopy, scanning electron microscope, transmission electron microscope and Fourier transform infrared spectroscopy. These analyses showed that AgNPs were distributed on the surface of S. cerevisiae. The application of S. cerevisiae–AgNPs in bacteria killing and heavy metal removal was studied. S. cerevisiae–AgNPs effectively inhibited the growth of E. coli with increasing concentrations of S. cerevisiae–AgNPs. E. coli was killed completely at high concentration S. cerevisiae–AgNPs (e.g., 100 or 200 µg mL^?1). S. cerevisiae–AgNPs as excellent heavy metal absorbents also have been studied. Using Cd²⁺ as model heavy metal, batch experiments confirmed that the adsorption behavior fitted the Langmuir adsorption isotherms and the Cd²⁺ adsorption capacity of S. cerevisiae–AgNPs was 15.01 mg g^?1. According to adsorption data, the kinetics of Cd²⁺ uptake by S. cerevisiae–AgNPs followed pseudo second-order kinetic model. Moreover, S. cerevisiae–AgNPs possessed ability of different heavy metals’ removal (e.g., Cr⁵⁺, As⁵⁺, Pb²⁺, Cu²⁺, Mn²⁺, Zn²⁺, Hg²⁺, Ni²⁺). The simulated contaminated water containing E. coli, Cd²⁺ and Pb²⁺ was treated using S. cerevisiae–AgNPs. The results indicated that the bionanocomposites can be used to develop antibacterial agents and bioremediation agents for water treatment.     

Specific detection of bioavailable phenanthrene and mercury by bacterium reporters in the red soil

Genetically engineered Pseudomonas putida reporters (BMB-PL and BMB-ME), which, respectively, carried phnS-luxCDABE and merR-egfp cassette, were used to determine bioavailable phenanthrene and mercury. Over a spiked range of concentrations and aged for 6 days in red soil samples, the reporters were tested to determine the optimal assay conditions and the bioavailable phenanthrene (0–60 mg kg^?1) and Hg²⁺ (0–240 μg kg^?1) were evaluated by the signal of the relative fluorescent units and relative luminescence units. Single contamination was carried out and good correlations were obtained between signal strength and pollutant concentrations, whereas interference and bioavailability repression were observed in dual-contamination experiments. Other heavy metal ions at nanomolar level did not interfere with BMB-ME measurement while BMB-PL showed some response to other polycyclic aromatic hydrocarbons or their intermediate products during degradation. Comparing high-performance liquid chromatography methods with the bacterial reporters, both BMB-ME and BMB-PL appeared to have a detection limit (mercury <40 μg kg^?1; phenanthrene <24 mg kg ^?1) similar to the instrumental analysis. Although physical parameters may affect the interaction of pollutants with bioreporter cells, advantages include the inherent biological relevance of the response, rapid response time, and potential for field deployment. Our results strongly suggest that the BMB-ME and BMB-PL bioreporters constitute an adaptable system for easily detecting the bioavailability of mercury and phenanthrene in the red soils.     

Cadmium (II)-selective electrode based on palm shell activated carbon modified with task-specific ionic liquid: kinetics and analytical applications

In this study, palm shell activated carbon modified with task-specific ionic liquid was used as a novel electrode component for the potentiometric determination of cadmium ions in water samples. The proposed potentiometric sensor has good operating characteristics, including relatively high selectivity towards the Cd (II) ion, a Nernstian response to Cd (II) ions in a working concentration range of 1.0 × 10^?9–1.0 × 10^?2 M, with a reasonable detection limit of 1 × 10^?10 M and a slope of 30.90 ± 1.0 mV/decade. No significant changes in electrode potential were observed when the pH was varied over the range of 4–9. A direct technique based on the use of ion-selective electrode potentiometry has been developed in our laboratory for the study of reaction kinetics and kinetic methods of analysis by continuous monitoring of the rate of production or consumption of an ion. The apparent adsorption rate constant was estimated assuming pseudo-second-order kinetics. Additionally, the proposed electrode has been successfully used for the determination of the cadmium content in real samples without a significant interaction from other cationic or anionic species.     

Hg<Superscript>0</Superscript>(liq)-Hg<Superscript>0</Superscript>(solution) equilibrium and solubility of elementary mercury in water

The solubility metallic mercury in water and its dominating forms were studied. The prevalence of the Hg_aq⁰ form in the high-temperature range was confirmed and the reaction constant Hg_liq⁰ ai Hg_aq⁰ (logK = logm = −8.01) at 25°C with the predominance of oxidized forms of mercury for the 20–80°C area of low temperatures was found.     

Isolation and characterization of metal-resistant bacterial strain from wastewater and evaluation of its capacity in metal-ions removal using living and dry bacterial cells

A novel strain of the genus Micrococcus isolated from wastewater was studied for resistance to seven heavy metals and forty antibiotics. Its capacity to accumulate metal ions was also realized at different pH. The strain exhibited high minimal inhibitory concentration values for metal ions tested and resist to 15 antibiotics. The living cells of the bacterial strain show a largest uptake capacity at pH 6–8.5 for copper, nickel, and zinc with values ranging from 51.45 to 83.90 %, 52.59 to 78.81 %, and 59.55 to 78.90 %, respectively. It was also able to absorbed 59.81–80.08 % of chromium and 58.09–79.41 % of cobalt at pH 7.3–8.5. The maximum lead uptake was obtained at pH 5.5–8.5 with an amount of 55.28–91.06 %. The significant absorption of cadmium was shown at pH 6.5 with 38 %. In 25 µg mL-1 zinc, chromium, and nickel solutions, dead cells of the isolate were able to biosorbed 20.46, 22.5, and 23.98 µg mL^?1, respectively, after 30 min of contact. In other solutions with higher concentrations 50 and 100 µg mL^?1, the amount of each metal immobilized was, respectively, as follows: 38.02 and 90.21 µg mL^?1 for zinc, 39.78 and 89.23 µg mL^?1 for chromium, and 47.19 and 86.83 µg mL^?1 for nickel. Due to its high-metal accumulation capacity in aerobic conditions, these Gram-positive bacteria may be potentially applicable in situ bioremediation of heavy metals contaminating aqueous systems.     

Relating food and human hair to assess mercury exposure levels in Poboya,Central Sulawesi,Indonesia

Poboya is a major small-scale gold-mining area in Central Sulawesi, Indonesia, that has been operating since 2009. About 200–500 kg of mercury is released each day as a result of gold-mining activities over a total area of 7000 ha. We examined mercury contamination by using two types of sample, namely food and human hair. Samples were obtained in Poboya and in the city of Palu, 11 km away. Samples of 22 foods were obtained from traditional markets in Poboya and Palu. Total mercury concentrations ranged from 0.003 to 0.31 µg/g in foods from Poboya and from 0.001 to 0.13 µg/g in those from Palu. The highest total mercury concentration in Poboya was found in unripe banana, which is frequently consumed by the local people. In Poboya, the weekly mercury intakes from foods were calculated at 180.3 µg/person from vegetables, 1.7 µg/person from processed foods, 51.4 µg/person from seafood, and 17.2 µg/person from meat and eggs. In Palu, the weekly mercury intakes were 2.9 µg/person from vegetables, 3.1 µg/person from processed foods, 60.8 µg/person from seafood, and 19 µg/person from meat and eggs. These findings delineated Poboya as an area polluted by mercury contamination. Intake of mercury-contaminated food influenced the results obtained in human hair. Hair concentrations of total mercury in Poboya ranged from 0.3 to 19.6 µg/g.     

Mercury Redox Chemistry in the Negro River Basin, Amazon: The Role of Organic Matter and Solar Light

Pristine water bodies in the Negro River basin, Brazilian Amazon, show relatively high concentrations of mercury. These waters are characterized by acidic pH, low concentrations of suspended solids, and high amounts of dissolved organic matter and are exposed to intense solar radiation throughout the year. This unique environment creates a very dynamic redox chemistry affecting the mobility of mercury due to the formation of the dissolved elemental species (Hg⁰). It has been shown that in this so-called black water, labile organic matter from flooded forest is the major scavenger of photogenerated H₂O₂. In the absence of hydrogen peroxide, these black waters lose their ability to oxidize Hg⁰ to Hg²⁺, thus increasing Hg⁰ evasion across the water/atmosphere interface, with average night time values of 3.80 pmol m^?2 h^?1. When the dry period starts, labile organic matter inputs gradually diminish, allowing the increasing concentration of H₂O₂ to re-establish oxidative water conditions, inhibiting the metal flux across the water/atmosphere interface and contributing to mercury accumulation in the water column.     

<Emphasis Type="Italic">Penicillium chrysogenum</Emphasis> immobilised silica: flame atomic absorption spectrometric Pb determination in industrial effluent,sludge and food samples

A solid phase extraction method based on the immobilisation of Penicillium chrysogenum on silica was developed for preconcentration and flame atomic absorption spectrometric determination of Pb(II). The immobilised sorbent was packed in a column to optimise the conditions for its quantitative sorption and desorption. Various parameters such as pH, type of eluent, sample and eluent flow rate and influence of others ions were systematically studied. Pb(II) was quantitatively sorbed at pH 4.0 at a flow rate of 2.0 mL min^?1 and eluted with 10.0 mL of 1.0 M HCl at 0.2 mL min^?1 flow rate. The devised procedure applied for Pb determination in tap water, an industrial effluent and sludge sample, black tea, spinach leaves and green beans (canned food) was reproducible, with a relative standard deviation of 0.8%. The method was validated by a BCR 701 standard lake sediment sample. The limit of detection and limit of quantification for Pb(II) were 7.16 and 23.88 μg L^?1, respectively, with an enrichment factor of 100.     

Adsorption of lead, zinc and cadmium ions from contaminated water onto Peganum harmala seeds as biosorbent

Peganum harmala seeds were assessed as biosorbent for removing Pb²⁺, Zn²⁺and Cd²⁺ ions from aqueous solutions. The effects of various parameters such as the aqueous solution pH, the contact time, the initial metal concentration and the amount of adsorbent in the process were investigated. The adsorption efficiencies increased with pH. It was found that about 95 % of lead, 75 % of zinc and 90 % of cadmium ions could be removed from 45 ml of aqueous solution containing 20 mg l^?1 of each cation with 2 g of adsorbent at pH 4.5 after 15 min. The quantitative desorption of cadmium from adsorbent surface was achieved using 10 ml of a 0.5 M nitric acid solution. This condition was attained for lead and zinc ions with 10 ml of 1 M hydrochloric acid solution. Kinetic investigation of the process was performed by considering a pseudo-second-order model. This model predicts the chemisorption mechanism of the process. Langmuir, Freundlich, Temkin and Dubinin–Radushkevich models were tested for describing the equilibrium data. It was found that the Freundlich model describes the experimental data resulting from the adsorption of lead ions. However for cadmium and zinc ions, the adsorption equilibria were interpreted with the Langmuir model.     

Chemical characterization and sources of PM2.5 at 12-h resolution in Guiyang,China

The increasing emission of primary and gaseous precursors of secondarily formed atmospheric particulate matter due to continuing industrial development and urbanization are leading to an increased public awareness of environmental issues and human health risks in China. As part of a pilot study, 12-h integrated fine fraction particulate matter (PM_2.5) filter samples were collected to chemically characterize and investigate the sources of ambient particulate matter in Guiyang City, Guizhou Province, southwestern China. Results showed that the 12-h integrated PM_2.5 concentrations exhibited a daytime average of 51 ± 22 µg m^?3 (mean ± standard deviation) with a range of 17–128 µg m^?3 and a nighttime average of 55 ± 32 µg m^?3 with a range of 4–186 µg m^?3. The 24-h integrated PM_2.5 concentrations varied from 15 to 157 µg m^?3, with a mean value of 53 ± 25 µg m^?3, which exceeded the 24-h PM_2.5 standard of 35 µg m^?3 set by USEPA, but was below the standard of 75 µg m^?3, set by China Ministry of Environmental Protection. Energy-dispersive X-ray fluorescence spectrometry (XRF) was applied to determine PM_2.5 chemical element concentrations. The order of concentrations of heavy metals in PM_2.5 were iron (Fe) > zinc (Zn) > manganese (Mn) > lead (Pb) > arsenic (As) > chromium (Cr). The total concentration of 18 chemical elements was 13 ± 2 µg m^?3, accounting for 25% in PM_2.5, which is comparable to other major cities in China, but much higher than cities outside of China.     

Sorption of inorganic mercury and monomethyl mercury in an iron–humus podzol soil of southern Norway studied by batch experiments

Considerable fractions of the Hg content of lake and river systems in Scandinavia are discharged from the soil of the catchments. An important soil type in Scandinavia is the iron–humus podzol. The sorption characteristics of this soil type for inorganic Hg(II) and monomethyl mercury were investigated by batch experiments. The solubility of Hg²⁺ and CH₃Hg⁺ in the soil horizons containing organic matter increases with increasing pH of the soil solution by favoring the formation of solute organic matter–mercury complexes. While the solubility of Hg²⁺ is strongly dependent on complexation to dissolved organic matter, the solubility of CH₃Hg⁺ is more dependent on ion exchange. The concentration of solute inorganic Hg(II) increased with increasing temperature probably because of an increase in the concentration of dissolved organic carbon. There was no effect of temperature on the concentration of solute CH₃Hg⁺. At pH values where inorganic mercury–hydroxo complexes are formed, inorganic Hg(II) is efficiently sorbed to the metal oxides of the mineral soil. The soil–water distributions of inorganic Hg(II) in the different soil horizons were described by Freundlich isotherms or linear isotherms for common and contaminated mercury contents in the soils.     

Coarse and fine particulates, Hg(p)-bound particulate concentrations and compositions study at Sha-Lu, central Taiwan

Ambient air and coarse, fine and particulate-bound mercury (Hg(p)) pollutants were collected and analyzed from March 17 to May 22 and September 3, 2009 to March 5, 2010 at a highway traffic site located in Sha-Lu, central Taiwan. This study has the following objectives: (1) to measure the coarse and fine particulates concentrations and the particulate-bound mercury Hg(p) which was attached to these particulate; (2) to determine the average Hg(p) compositions in coarse and fine particulates and (3) to compare the Hg(p) concentrations and compositions particulate in this study to the those obtained in other studies. The results obtained in this study indicated that the average ambient air PM_2.5, PM_2.5–10 and PM₁₀ were 18.79 ± 6.71, 11.22 ± 4.93 and 30.01 ± 10.27 μg/m³, respectively. The ranges of concentrations for Hg(p) in PM_2.5 were from 0.0016 to 0.0557 ng/m³, from 0.0006 to 0.0364 ng/m³ in PM_2.5–10 and from 0.0022 to 0.0862 ng/m³ in PM₁₀. In addition, the highest particle-bound mercury compositions in PM_2.5 were 16.85 ng/g and the lowest particle-bound mercury concentrations were 0.55 ng/g. The highest particle-bound mercury compositions in PM_2.5–10 were 13.88 ng/g and the lowest particle-bound mercury in PM_2.5–10 were 0.22 ng/g.     

Characteristics and distributions of atmospheric mercury emitted from anthropogenic sources in Guiyang,southwestern China

Continuous measurements of speciated atmospheric mercury (Hg), including gaseous elemental mercury (GEM), particulate mercury (PHg), and reactive gaseous mercury (RGM) were conducted in Guizhou Province, southwestern China. Guiyang Power Plant (GPP), Guiyang Wujiang Cement Plant, Guizhou Aluminum Plant (GAP), and Guiyang Forest Park (GFP) in Guiyang were selected as study sites. Automatic Atmospheric Mercury Speciation Analyzers (Tekran 2537A) were used for GEM analysis. PHg and RGM were simultaneously collected by a manual sampling system, including elutriator, coupler/impactor, KCl-coated annular denuder, and a filter holder. Results show that different emission sources dominate different species of Hg. The highest average GEM value was 22.2 ± 28.3 ng·m^?3 and the lowest 6.1 ± 3.9 ng·m^?3, from samples collected at GPP and GAP, respectively. The maximum average PHg was 1984.9 pg·m^?3 and the minimum average 55.9 pg·m^?3, also from GPP and GAP, respectively. Similarly, the highest average RGM of 68.8 pg·m^?3 was measured at GPP, and the lowest level of 20.5 pg·m^?3 was found at GAP. We conclude that coal combustion sources are still playing a key role in GEM; traffic contributes significantly to PHg; and domestic pollution dominates RGM.     

Sorption of heavy metals from aqueous solution by dehydrated powders of aquatic plants

Ruppia maritima and Echinodorus amazonicus were prepared in a dehydrated powder form. The characteristics and mechanisms of adsorption of heavy metals were studied under various pH values, reaction times, and heavy metal ion concentrations. The results showed that under different pH and reaction time conditions, heavy metal adsorption was lead > cadmium > zinc > copper. The adsorption of lead increased linearly with the lead concentration. For cadmium, zinc and copper, the adsorption was saturated when metal ion concentration exceeded 200 mg/L. When a Freundlich model was applied, R ² values for the heavy metal adsorption by the aquatic plants mostly exceeded 0.9. The adsorption of heavy metal ions by these two aquatic plant powders was better explained by the Lagergren second-order equation than the first-order equation. From the Fourier Transform Infrared spectra, there was an adsorption peak at 2,115 cm^?1 for R. maritima. The peak shape did not change with metal affiliation except there was a shift of peak wavelength before adsorption. The results indicate that the mechanism of heavy metal adsorption by the two species is not simply on the mono-molecular layer level, and that intra-particulate dispersal is the dominant process. Heavy metal pollution does not affect the basic chemical components, and major substances involved in heavy metal adsorption including carbohydrates, cell wall pectin, and protein functional groups.     

Fast,green and effective chromium bio-speciation using <Emphasis Type="Italic">Sepia pharaonis</Emphasis> endoskeleton nano-powder

The development of a fast, effective, simple and low-cost procedure for chromium speciation is an analytical challenge. In this work, a new and simple method for speciation and determination of chromium species in different matrices was developed. Sepia pharaonis endoskeleton nano-powder was used as an adsorbent for the dispersive micro-solid-phase extraction. Finally, the desorbed chromium was determined using a graphite furnace atomic absorption spectrometer. The experimental results showed that Cr(III) could be quantitatively extracted by the adsorbent, while Cr(VI) adsorption was negligible. Concentrated H₂SO₄ and ethanol reduced Cr(VI)–Cr(III), and total chromium content was assessed as Cr(III). Then, the Cr(VI) concentration in the sample was calculated as the difference. The optimum conditions were obtained in terms of pH, adsorbent amount, contact time, and type, concentration and volume of eluent. Under the optimum conditions that involved the speciation of chromium ions from 25 mL of the water samples at pH 7.0 using 0.025 g of the adsorbent with contact time of 5 min, the method was validated in terms of linearity, precision and accuracy. The calibration curve was linear over the concentration range of 0.01–25.00 μg L^?1 for Cr(III). The obtained limit of detection for the proposed method was 0.003 µg L^?1. The maximum adsorption capacity of the adsorbent was found to be 995.57 mg g^?1. The proposed method was validated by the speciation of Cr(III) and Cr(VI) in different real water and wastewater samples with satisfactory results.     

Studies on an efficient method for determining ethyl carbamate in the workplace air

In relation to the proposal to introduce an occupational exposure limit value for ethyl carbamate (EC) in Poland, a need to develop a sensitive method for determination of this carcinogenic substance in the workplace air was emerged. In the presented paper, a new method for its determination by high-performance liquid chromatography (HPLC) with fluorescence detector (FLD) is proposed. The method is based on the adsorption of EC on the cellulose filter, its extraction with water, further reaction of EC with 9-xanthydrol in acidic solution. Determination of the obtained EC derivative (N-xanthyl ethyl carbamate) was then conducted in a reverse-phase system with acetonitrile and water mobile phase at a flow rate of 1 mL/min on an Ultra C18 column of 250 mm by HPLC–FLD. Measurement range of 0.1–2 µg/m³ for a 1440 L of air sample was appropriate to the established maximum admissible concentration value of 1 µg/m³. The limit of detection is 0.142 ng/mL, and the limit of quantification is 0.426 ng/mL, respectively. The developed quantitative method makes it possible to determine ethyl carbamate in workplace air, which in turn allows determining exposure indicators and facilitates occupational risk assessment for the employees.     

Determination of atrazine isotherms on agricultural soils

For determination of atrazine isotherms in agricultural soils of Fars Province, composite soil samples from 0 to 5 cm depth with textures of silty clay loam, clay loam and loam were collected. In order to form the atrazine isotherms, 10, 50 and 100 µg atrazine g^?1 soil was added to the soil samples. Soluble atrazine in water:soil ratios of 10:1, 50:1 and 200:1 was measured after 3-h shaking. Finally, for each cases of applied atrazine, water extractable atrazine was determined and quantified using gas chromatography instrument. The results indicated that there was a linear relationship between the logarithms of water extractable atrazine and added atrazine for different water:soil ratios. A general equation of WEA = K(WS) ^α (AA) ^β is obtained experimentally between water extractable atrazine, µg g^?1(WEA), and added atrazine, µg g^?1 (AA), where K, α and β are absorption constants; WS is the water:soil ratio, g g^?1. For the loam, silty clay loam and clay loam soil textures, the α were 0.49, 0.23 and 0.13, respectively, the β were 0.55, 0.806 and 0.21, respectively, and the K were 1.44, 0.78 and 25.38, respectively.     

Quantifying land use influences on event-based flow frequency,timing, magnitude,and rate of change in an urbanizing watershed of the central USA

There is a need for research that advances understanding of flow alterations in contemporary watersheds where natural and anthropogenic interactions can confound mitigation efforts. Event-based flow frequency, timing, magnitude, and rate of change were quantified at five-site nested gauging sites in a representative mixed-land-use watershed of the central USA. Statistically independent storms were paired by site (n = 111 × 5 sites) to test for significant differences in event-based rainfall and flow response variables (n = 17) between gauging sites. Increased frequency of small peak flow events (i.e., 64 more events less than 4.0 m³ s^?1) was observed at the rural–urban interface of the watershed. Differences in flow response were apparent during drier periods when small rainfall events resulted in increased flow response at urban sites in the lower reaches. Relationships between rainfall and peak flow were stronger with decreased pasture/crop land use and increased urban land use by approximately 20%. Event-based total rainfall explained 40–68% of the variance in peak flow (p < 0.001). Coefficients of determination (r²) were negatively correlated with pasture/crop land use (r² = 0.92; p = 0.007; n = 5) and positively correlated with urban land use (r² = 0.90; p = 0.008; n = 5). Significant differences in flow metrics were observed between rural and urban sites (p < 0.05; n = 111) that were not explained by differences in rainfall variables and drainage area. An urban influence on flow timing was observed using median time lag to peak centroid and time of maximum precipitation to peak flow. Results highlight the need to establish manageable flow targets in rapidly urbanizing mixed-land-use watersheds.     

Modification of PPTA-based polymeric waste and adsorption properties for metal ions

Novel composite adsorbents PPTA-AOx were synthesized by grafting polyacrylonitrile onto poly(p-phenylene terephthalamide) (PPTA) followed by converting the acrylonitrile into the amidoxime (AO) groups. Their structures were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, elemental analysis, transmission electron microscopy, etc. Scanning electron microscopy analysis and pore structure analysis manifested that PPTA-AOx adsorbents are all composed of nanoparticles aggregation. The as-synthesized PPTA-AOx adsorbents showed good adsorption capacity for Hg²⁺ with a maximum adsorption capacity of 2.50 mmol g^?1. The pseudo-second-order model can reasonably describe the adsorption kinetics of the three adsorbents for Hg²⁺. Langmuir model provided better fit for the isothermal adsorption of Hg²⁺ on PPTA-AO₁ and PPTA-AO₂, while the Freundlich model was better for PPTA-AO₃. The adsorption process might involve both chemisorption and physisorption. According to the calculated thermodynamic parameters, it can be concluded that the adsorption is an endothermic, spontaneous and entropy-driven process.     

Crystal nucleation and growth produced by continuous decompression of Pinatubo magma

High-temperature decompression experiments demonstrate that crystal textures preserve a record of the style and rate of magmatic ascent. To reinforce this link, we performed a suite of isothermal decompression experiments using starting material from the climactic 1991 Pinatubo eruption. We decompressed experiments from 220 MPa to final, quench pressures of 75 or 30 MPa using continuous decompression rates of 100, 30, 10, 3, 1, and 0.3 MPa h^?1. Amphibole, clinopyroxene, and plagioclase crystallized during the experiments, with plagioclase microlites dominating the assemblage. Total microlite number densities range from 10^7.6±0.4 up to 10^8.2±0.2 cm^?3, with plagioclase accounting for up to 65% of the total number. Plagioclase microlite area increased systematically from 19?±?8 to 937?±?487 µm² with increasing experiment duration. Our textures provide time-integrated records of crystal kinetics. Average nucleation and areal growth rates of plagioclase are highest in the fastest decompressions (~?10^7.5 cm^?3 h^?1 and 10.1?±?4.1 µm² h^?1, respectively) and more than an order of magnitude lower in the slowest experiments (~?10^5.5 cm^?3 h^?1 and 0.8?±?0.2 µm² h^?1, respectively). Both nucleation and growth rates are highest at high degrees of disequilibrium. We find that peak supersaturation-dependent instantaneous rates are generally more than an order of magnitude faster than average rates. We use those instantaneous nucleation and growth rates to introduce an iterative model to evaluate the effects of different decompression rates, decompression paths (continuous, single-step or multistep), and the presence of phenocrysts on final crystallinity and microlite size distribution.