Characteristics of the geothermal water in Changbai Mountain volcanic region,northeast of China

Geothermal water is plentiful in Changbai Mountain region, northeastern China, due to the volcanic activities and widespread faults. For the exploration of geothermal resources, this study uses quartz and cation geothermometer to estimate the temperatures of the geothermal reservoir and uses the tubular models to evaluate the thermal gradient. The hydrogeochemical characteristics of the geothermal resources were also evaluated by hydrogeochemical analysis. The results showed that the geothermal reservoir temperatures of the four major thermal springs in Changbai Mountain region range from 72 to 169 °C. The average geothermal reservoir temperatures of Jinjiang hot springs, Changbai hot springs I, Xianrenqiao hot springs, and Changbai hot springs II are 129.25, 169, 89, and 73.67 °C, respectively. The geothermal gradient values of the four major thermal springs have different characteristics. The geothermal gradient values of Jinjiang hot springs and Changbai hot springs I are 4.6 and 3.1 °C/100 m, respectively. The geothermal gradient values of Xianrenqiao thermal springs and Changbai thermal springs II are both lower than 1.5 °C/100 m, with the values of 1.1 and 1.4 °C/100 m. And the geothermal gradients are influenced by Changbai Mountain Tianchi volcano. In addition, the water chemical analyses showed that the geothermal water types are HCO₃-Na with higher concentrations of Na⁺, Cl^?, SO₄ ^2?, TDS, and HCO₃ ^? than the non-thermal waters, which suggested a deep and long water cycle of the thermal water, and therefore a sufficient water-rock interaction.     

Hydrochemical,isotopic, and reservoir characterization of the Pasinler (Erzurum) geothermal field,eastern Turkey

The reservoir temperature and conceptual model of the Pasinler geothermal area, which is one of the most important geothermal areas in Eastern Anatolia, are determined by considering its hydrogeochemical and isotope properties. The geothermal waters have a temperature of 51 °C in the geothermal wells and are of Na–Cl–HCO₃ type. The isotope contents of geothermal waters indicate that they are of meteoric origin and that they recharge on higher elevations than cold waters. The geothermal waters are of immature water class and their reservoir temperatures are calculated as 122–155 °C, and their cold water mixture rate is calculated as 32%. According to the δ¹³C_VPDB values, the carbon in the geothermal waters originated from the dissolved carbon in the groundwaters and mantle-based CO₂ gases. According to the δ³⁴S_CDT values, the sources of sulfur in the geothermal waters are volcanic sulfur, oil and coal, and limestones. The sources of the major ions (Na⁺, Ca²⁺, Mg²⁺, Cl^?, and HCO₃ ^?) in the geothermal waters are ion exchange and plagioclase and silicate weathering. It is determined that the volcanic rocks in the area have effects on the water chemistry and elements like Zn, Rb, Sr, and Ba originated from the rhyolite, rhyolitic tuff, and basalts. The rare earth element (REE) content of the geothermal waters is low, and according to the normalized REE diagrams, the light REE are getting depleted and heavy REE are getting enriched. The positive Eu and negative Ce anomalies of waters indicate oxygen-rich environments.     

Hydrogeochemical investigations of thermal waters in the northeastern part of Morocco

Northeastern Morocco is characterised by a large number of surface geothermal manifestations. Thermal waters are hosted within sedimentary rocks, and in particular the Liassic dolomitic limestones act as a reservoir. The presence of geothermal waters is closely related to important fault systems. Meteoric water infiltrates along those fractures and faults, gets heated, and then returns to the surface through hydrothermal conduits. Most of the thermal waters are of Na–Cl and Ca–Mg–HCO₃ types. In this paper different geochemical approaches were applied to infer the reservoir temperature. Na–K–Mg^1/2 ternary diagram points to temperatures ranging from 100 to 180 °C. Cation geothermometers suggest an average reservoir temperature of about 100 °C. Mineral solution equilibria analysis yields temperatures ranging from 50 to 185 °C. The silica enthalpy mixture model gives an average value (about 110 °C) higher than that inferred from cation geothermometers.     

Geothermometry applications for the Balıkesir thermal waters,Turkey

In this study, reservoir temperatures of Balıkesir geothermal waters in northwestern Turkey are estimated with various geochemical models. The geothermal fluids in the region are represented by Na–SO₄, Na–HCO₃ and Ca–HCO₃ type waters with discharge temperatures up to 98°C. It was determined that the solubility of silica in most of the waters is controlled by the chalcedony phase. Equilibrium states of the Balıkesir thermal waters studied by means of Na–K–Mg–Ca diagram, mineral saturation calculations and activity diagrams in the system composed of Na₂O–CaO–K₂O–Al₂O₃–SiO₂–H₂O phases approximate a reservoir temperature of about 120°C. Most of the waters are found to be equilibrated with calcite, chalcedony ± quartz and muscovite at predicted temperature ranges, similar to those calculated from the chemical geothermometers.     

Hydrogeochemistry of thermal and mineralized waters in the Diyadin (Ağri) area,Eastern Turkey

The Diyadin Geothermal area, located in the eastern part of Anatolia (Turkey) where there has been recent volcanic activity, is favorable for the formation of geothermal systems. Indeed, the Diyadin geothermal system is located in an active geodynamic zone, where strike-slip faults and tensional cracks have developed due to N–S regional compression. The area is characterized by closely spaced thermal and mineralized springs, with temperatures in the range 30–64 °C, and flowrates 0.5–10 L/s. Thermal spring waters are mainly of Ca(Na)-HCO₃ and Ca(Mg)-SO₄ types, with high salinity, while cold groundwater is mostly of Ca(Na, Mg)-HCO₃ type, with lower salinity. High contents of some minor elements in thermal waters, such as F, B, Li, Rb, Sr and Cs probably derive from enhanced water–rock interaction.Thermal water samples collected from Diyadin are far from chemical equilibrium as the waters flow upward from reservoirs towards spring vents and possibly mix with cooler waters. The temperatures of the deep geothermal reservoirs are estimated to be between 92 and 156 °C in Diyadin field, based on quartz geothermometry, while slightly lower estimates are obtained using chalcedony geothermometers. The isotopic composition of thermal water (δ¹⁸O, δ²H, δ³H) indicates their deep-circulating meteoric origin. The waters are likely to have originated from the percolation of rainwater along fractures and faults to the deep hot reservoir. Subsequent heating by conduction due to the presence of an intrusive cupola associated with the Tendurek volcano, is followed by the ascent of deep waters to the surface along faults and fractures that act as hydrothermal conduits.Modeling of the geothermal fluids indicates that the fluid is oversaturated with calcite, aragonite and dolomite, which matches travertine precipitation in the discharge area. Likewise, the fluid is oversaturated with respect to quartz, and chalcedony indicating the possibility of siliceous precipitation near the discharge areas. A conceptual hydro-geochemical model of the Diyadin thermal waters based on the isotope and chemical analytical results, has been constructed.     

Isotope–geochemical characterization and geothermometrical modeling of Uttarakhand geothermal field,India

Uttarakhand geothermal area, located in the central belt of the Himalayan geothermal province, is one of the important high temperature geothermal fields in India. In this study, the chemical characteristics of the thermal waters are investigated to identify the main geochemical processes affecting the composition of thermal waters during its ascent toward the surface as well as to determine the subsurface temperature of the feeding reservoir. The thermal waters are mainly Ca–Mg–HCO₃ type with moderate silica and TDS concentrations. Mineral saturation states calculated from PHREEQC geochemical code indicate that thermal waters are supersaturated with respect to calcite, dolomite, aragonite, chalcedony, quartz (SI > 0), and undersaturated with respect to gypsum, anhydrite, and amorphous silica (SI < 0). XRD study of the spring deposit samples fairly corroborates the predicted mineral saturation state of the thermal waters. Stable isotopes (δ¹⁸O, δ²H) data confirm the meteoric origin of the thermal waters with no oxygen-18 shift. The mixing phenomenon between thermal water with shallow ground water is substantiated using tritium (³H) and chemical data. The extent of dilution is quantified using tritium content of thermal springs and non-thermal waters. Classical geothermometers, mixing model, and multicomponent fluid geothermometry modeling (GeoT) have been applied to estimate the subsurface reservoir temperature. Among different classical geothermometers, only quartz geothermometer provide somewhat reliable estimation (96–140 °C) of the reservoir temperature. GeoT modeling results suggest that thermal waters have attained simultaneous equilibrium with respect to minerals like calcite, quartz, chalcedony, brucite, tridymite, cristobalite, talc, at the temperature 130 ± 5 °C which is in good agreement with the result obtained from the mixing model.     

Hydrogeochemical and isotopic investigation of the Bursa-Oylat thermal waters, Turkey

The Oylat spa is located 80 km southeast of Bursa and 30 km south of Ineg?l in the Marmara region. With temperature of 40°C and discharge of 45 l/s, the Oylat main spring is the most important hot water spring of the area. Southeast of the spa the Forest Management spring has a temperature of 39.4°C and discharge of 2 l/s. The G?z spring 2 km north of the spa, which is used for therapy of eye disease, and cold waters of the Saadet village springs with an acidic character are the further important water sources of the area. EC values of Main spring and Forest Management hot spring (750–780 μS/cm) are lower than those of Saadet and G?z spring waters (2,070–1,280 μS/cm) and ionic abundances are Ca > Na + K > Mg and SO₄ > HCO₃ > Cl. The Oylat and Sızı springs have low Na and K contents but high Ca and HCO₃ concentrations. According to AIH classification, these are Ca–SO₄–HCO₃ waters. Based on the results of δ¹⁸O, ²H and ³H isotope analyses, the thermal waters have a meteoric origin. The meteoric water infiltrates along fractures and faults, gets heated, and then returns to surface through hydrothermal conduits. Oylat waters do not have high reservoir temperatures. They are deep, circulating recharge waters from higher enhanced elevations. δ¹³C_DIC values of the Main spring and Forest Management hot spring are −6.31 and −4.45‰, respectively, indicating that δ¹³C is derived from dissolution of limestones. The neutral pH thermal waters are about +18.7‰ in δ³⁴S while the sulfate in the cold waters is about +17‰ (practically identical to the value for the neutral pH thermal waters). However, the G?z and Saadet springs (acid sulfate waters) have much lower δ³⁴S values (~+4‰).     

Hydrogeochemistry and reservoir characterization of the Konya geothermal fields,Central Anatolia/Turkey

A conceptual model with water samples from ten geothermal fields (?smil, Ilg?n (Çavu?cugöl), Tuzlukçu-Ak?ehir, Seydi?ehir and Kavakköy, Hüyük, Ere?li-Akhüyük, Kad?nhan?, Cihanbeyli, Karap?nar and Bey?ehir) in the province of Konya defined the geothermal system. Carbonates, quartzite and marbles of Paleozoic metamorphics are the reservoir rocks and the heating sources are igneous rock intrusions and geothermal gradient. The variable thermal water (CaMgHCO₃, CaSO₄, NaSO₄, CaHCO₃, CaNaHCO₃, NaCl and CaNaClHCO₃) had EC and temperature between 177.8 and 56,100 μS/cm and between 18.3 and 44 °C, respectively. Ca²⁺ in geothermal fluids are associated with marble and carbonate rocks and the high chloride shows direct connection with deep geothermal system, and prolonged contact with evaporite rocks. Sulphate originates from dissolution of and oxidation of sulphate and sulphur-bearing minerals. The high As, B, F and Mn concentration in some thermal water samples were determined as 85 μg/l, 148.56 mg/l, 3.01 mg/l and 208.13 mg/l, respectively. Reservoir temperatures computed by Na/K geothermometers were between 85.37–158.89 °C for Ak?ehir thermal waters and 58.78–90.45 °C for Ere?li thermal waters. The maximum reservoir temperature of other geothermal waters was 75 °C by the silica geothermometers.     

Hydrochemical and isotopic properties of Heybeli geothermal area (Afyon,Turkey)

The thermal waters at the Heybeli (K?z?lkirse) low-temperature geothermal field located in the Afyonkarahisar Province (western Turkey) are discharged from Paleozoic recrystallized limestone. The temperature, specific electrical conductivity, and pH values of the thermal waters are within the range of 28.9 to 54.7 °C, 587 to 3580 μS/cm, and 6.32 to 7.37, respectively. The Heybeli geothermal system is fed by meteoric waters. The waters are heated at depth by high geothermal gradient caused by the neotectonic activity in the deep and ascend to the surface through fractures and faults by convection. The thermal waters are of Na-Ca-HCO₃-SO₄ type and their chemical composition of the waters is mainly controlled by water-rock interaction and mixing processes. The δ¹⁸O, δ²H and tritium compositions show that the thermal waters are of meteoric origin and the residence time at the reservoir is longer than 50 years. Isotope data (δ³⁴S and δ¹³C) indicate recrystallized limestones as origin of CO₂ and structural substitution of sulfate into marine carbonates (CAS) as origin of sulfur. Chemical, \( {\updelta}^{18}{\mathrm{O}}_{\left({\mathrm{SO}}_4-{\mathrm{H}}_2\mathrm{O}\right)} \) isotope geothermometers and mineral equilibrium diagrams applied to thermal waters gave reservoir temperatures between 62 and 115 °C. Saturation index calculations show that the most expected minerals causing scaling at outflow conditions during the production and utilization of Heybeli geothermal waters are calcite, aragonite, dolomite, quartz, and chalcedony.     

Hydrogeochemical and isotopic characteristics of the Ilica geothermal system (Erzurum,Turkey)

In this paper, the hydrochemical isotopic characteristics of samples collected from geothermal springs in the Ilica geothermal field, Eastern Anatolia of Turkey, are examined and described. Low-temperature geothermal system of Ilica (Erzurum, Turkey) located along the Eastern Anatolian fault zone was investigated for hydrogeochemical and isotopic characteristics. The study of ionic and isotopic contents shows that the thermal water of Ilica is mainly, locally fed by groundwater, which changes chemically and isotopically during its circulation within the major fault zone reaching depths. The thermal spring has a temperature of 29–39 °C, with electrical conductivity ranging from 4,000 to 7,510 µS/cm and the thermal water is of Na–HCO₃–Cl water type. The chemical geothermometers applied in the Ilica geothermal waters yielded a maximum reservoir temperature of 142 °C according to the silica geothermometers. The thermal waters are undersaturated with respect to gypsum, anhydrite and halite, and oversaturated with respect to dolomite. The dolomite mineral possibly caused scaling when obtaining the thermal waters in the study area. According to the enthalpy chloride-mixing model, cold water to the thermal water-mixing ratio is changing between 69.8 and 75 %. The δ¹⁸O–δ²H compositions obviously indicate meteoric origin of the waters. Thermal water springs derived from continental precipitation falling on to higher elevations in the study area. The δ¹³C ratio for dissolved inorganic carbonate in the waters lies between 4.63 and 6.48 ‰. In low-temperature waters carbon is considered as originating from volcanic (mantle) CO₂.     

Fluid-mineral equilibria in a hydrothermal system,Roosevelt hot springs,Utah

The availability of fluids and drill cuttings from the active hydrothermal system at Roosevelt Hot Springs allows a quantitative comparison between the observed and predicted alteration mineralogy, calculated from fluid-mineral equilibria relationships. Comparison of all wells and springs in the thermal area indicates a common reservoir source, and geothermometer calculations predict its temperature to be higher ($\text{288°C ± 10°}$) than the maximum measured temperature of 268°C.The composition of the deep reservoir fluid was estimated from surface well samples, allowing for steam loss, gas release, mineral precipitation and ground-water mixing in the well bore. This deep fluid is sodium chloride in character, with approximately 9700 ppm dissolved solids, a pH of 6.0, and gas partial pressures of O₂ ranging from 10^?32 to 10^?35 atm, CO₂ of 11 atm, H₂S of 0.020 atm and CH₄ of 0.001 atm.Comparison of the alteration mineralogy from producing and nonproducing wells allowed delineation of an alteration pattern characteristic of the reservoir rock. Theoretical alteration mineral assemblages in equilibrium with the deep reservoir fluid, between 150° and 300°C, in the system Na₂O-K₂O-CaO-MgO-FeO-Fe₂O₃-Al₂O₃-H₄SiO₄-H₂O-H₂S-CO₂-HCl, were calculated. Minerals theoretically in equilibrium with the calculated reservoir fluid at $\text{>240°C}$ include sericite, K-feldspar, quartz, chalcedony, hematite, magnetite and pyrite. This assemblage corresponds with observed higher-temperature ($\text{>210°C}$) alteration assemblage in the deeper parts of the producing wells. The presence of montmorillonite and mixed-layer clays with the above assemblage observed at temperatures <210°C corresponds with minerals predicted to be in equilibrium with the fluid below 240°C.Alteration minerals present in the reservoir rock that do not exhibit equilibrium with respect to the reservoir fluid include epidote, anhydrite, calcite and chlorite. These may be products of an earlier hydrothermal event, or processes such as boiling and mixing, or a result of errors in the equilibrium calculations as a result of inadequate thermochemical data.     

Hydrogeochemistry,environmental isotopes and the origin of the Hamamayagi-Ladik thermal spring (Samsun,Turkey)

Hamamayagi thermal spring (HTS) is located along the North Anatolian Fault Zone. The thermal spring has a temperature of 36°C, with total dissolved solids ranging from 485.6 to 508.5 mg/L. Hard, brittle, and gray limestones Permian aged are the reservoir rocks of the HTS. δ¹⁸O–δ²H isotope ratios clearly indicate a meteoric origin for the waters. The δ³⁴S value of sulfate in the thermal water is nearly 4.1‰ and implies a diagenetic environment characterized by reduced sulfur compounds. The δ¹³C ratio for dissolved inorganic carbonate in the HTS lies between −1.78 and −1.62‰, showing that it originates from the dissolution of fresh-water carbonates. Quartz geothermometry suggests a reservoir temperature of 52–85°C for the Hamamayagi geothermal field, but chalcedony geothermometers suggest reservoir temperatures between 30 and 53°C.     

Geochemical assessment,mixing behavior and environmental impact of thermal waters in the Guelma geothermal system,Algeria

A study of thirteen geothermal springs located in the geothermal field of Guelma, northeastern Algeria, was conducted. Samples were collected during the period between January 2014 and February 2016. Geochemical processes responsible for the chemical composition of thermal and mineralized water were evaluated. The hydrochemical analysis shows that the thermal waters are characterized by the presence of two different chemical facies, the first type SO₄–Ca in the east, west and south of Guelma, the second type HCO₃–Ca in the south. This analysis also attributed to sodium, chlorides, and sulfates to an evaporitic terrigenous origin by the molar ratio Sr²⁺/Ca²⁺. The thermal spring waters from Guelma geothermal system have a meteoric origin, and all samples are immature with strong mixing between hot and shallow waters with 19–38.5% rate of mixing. The silica geothermometer shows that these thermal waters have a temperature varying from 84 to 122 °C and that the water came from a depth of 2100–3000 m through a fault system that limits the pull-apart basin of Guelma. Potential environmental effluent from thermal spas could pollute in both the irrigation and drinking waters, and which imposes danger on the health of the inhabitants of the region.

     

Geochemical and isotope hydrological characterisation of geothermal resources at Godavari valley,India

Thermal waters at the Godavari valley geothermal field are located in the Khammam district of the Telangana state, India. The study area consists of several thermal water manifestations having temperature in the range 36–76 °C scattered over an area of ~35 km². The thermal waters are Na–HCO₃ type with moderate silica and TDS concentrations. In the present study, detailed geochemical (major and trace elements) and isotope hydrological investigations are carried out to understand the hydrogeochemical evolution of these thermal waters. Correlation analysis and principal component analysis (PCA) are performed to classify the thermal waters and to identify the different geochemical processes controlling the thermal water geochemistry. From correlation matrix, it is seen that TDS and EC of the thermal springs are mainly controlled by HCO₃ and Na ions. In PCA, thermal waters are grouped into two distinct clusters. One cluster represents thermal waters from deeper aquifer and other one from shallow aquifer. Lithium and boron concentrations are found to be similar followed by rubidium and caesium concentrations. Different ternary plots reveal rock–water interaction to be the dominant mechanism for controlling trace element concentrations. Stable isotopes (δ¹⁸O, δ²H) data indicate the meteoric origin of the thermal waters with no appreciable oxygen-18 shift. The low tritium values of the samples originating from deeper aquifer reveal the long residence time (>50 years) of the recharging waters. XRD results of the drill core samples show that quartz constitutes the major mineral phase, whereas kaolinite, dolomite, microcline, calcite, mica, etc. are present as minor constituents. Quartz geothermometer suggests a reservoir temperature of 100 ± 20 °C which is in good agreement with the values obtained from K–Mg and Mg-corrected K–Mg–Ca geothermometers.     

Variation in sericite compositions from fracture zones within the Coso Hot Springs geothermal system

Two types of white micas are found in drillhole samples within the geothermal system at Coso Hot Springs. Low-permeability zones of the crystalline basement contain coarse-grained relict muscovite, whereas rock alteration near fracture zones at temperatures > 150°C is characterized by abundant finegrained sericite in association with secondary calcite and quartz and unaltered relict microcline. In this hydrothermal sericite there is an increase in interlayer K, octahedral Mg + Fe_total and tetrahedral Al with increasing temperature between ~215° to >250°C.Thermodynamic activity of the Al₂Si₄O₁₀(OH)₂ component of serielles, calculated using site-mixing approximations of Helgeson and Aagaard (1985), decreases with increasing temperature between ~215° and >250°C. As a consequence of the observed variations in the interlayer, octahedral and tetrahedral site occupancies, the activity of KAl₂(AlSi₃O₁₀(OH)₂ is essentially constant in the Coso seriates over this temperature range. The calculated equilibrium distribution of aqueous species in the hydrothermal solutions produced from well 16−8, together with cation-activity phase diagrams that account for variations in sericite composition, requires a pH of ~6.7–6.8 at temperatures between 236° and 250°C. Comparison of predicted and observed phase relations with fluid compositions indicate that seriates are in local equilibrium with the geothermal reservoir fluid, whereas relict metamorphic muscovites are metastable.Although the compositions of hydrothermal sericites are a complex function of temperature, pressure and geothermal fluid composition, compositional relations observed at Coso together with published compositions of hydrothermal dioctahedral layer-silicates from the Salton Sea geothermal system demonstrates that elemental compositions of interlayer K and tetrahedral Al increase systematically with increasing temperature despite the dramatic differences in fluid compositions between these two geothermal systems. This suggests that the observed variations in interlayer and tetrahedral site occupancy is largely dependent on the enthalpy of hydrolysis reactions representing equilibrium between sericite solid solutions and the geothermal reservoir fluids.     

Mineral equilibria and geothermometry of the Dalaman–Köyceğiz thermal springs,southern Turkey

The Dalaman and Köyceğiz thermal springs are from karstic limestones belonging to Upper Cretaceous to Burdigalian Beydağları autochthon and Carboniferous to Lutetian Lycian nappes. They have measured temperatures of 24– 41 °C, specific electrical conductivities of 14,310–45,600 μS/cm, and are dominated by Na (1550–8500 mg/kg) and Cl (2725–15,320 mg/kg). The heat source of the geothermal systems of the area is tectonic related and the occurrence of the thermal springs is related to the young normal faults. Meteoric waters and seawaters recharge the reservoir rocks, are heated at depth with increasing geothermal gradient, and move up to the surface through the fractures and faults by convection trend and emerge as thermal springs. While thermal waters move up to the surface, they mix with different proportions of seawater and cold fresh waters. The seawater contribution to the thermal waters varies from 24% to 78%. Lake waters in the area are connected with thermal waters. Consequently, their chemical composition is influenced by the chemistry of thermal waters. Chemical equilibrium modelling based on measured outlet temperatures and measured pH shows that all the waters are oversaturated with respect to quartz and K-mica and undersaturated with respect to Al(OH)₃, anorthite, gypsum, siderite and SiO₂(a). Albite, alunite, aragonite, Ca-montmorillonite, calcite, chalcedony, chlorite, dolomite, Fe(OH)₃(a), fluorite, gypsum, illite, K-feldspar, kaolinite and sepiolite minerals are mostly oversaturated or undersaturated. Mineral saturation studies of the thermal springs indicate that dolomite, chalcedony and quartz are most likely to cause scaling at outlet conditions. Assessments from various chemical geothermometers, and Na–K–Mg ternary and mineral equilibrium diagrams suggest that the reservoir temperature is around 65–90 °C. The temperatures obtained from quartz, quartz-steam loss, Mg/Li geothermometers and mineral equilibrium diagrams give the most reasonable results.     

Geochemical constraint on origin and evolution of solutes in geothermal springs in western Yunnan,China

Geothermal resources are very rich in Yunnan, China. However, source of dissolved solutes in geothermal water and chemical evolution processes remain unclear. Geochemical and isotopic studies on geothermal springs and river waters were conducted in different petrological-tectonic units of western Yunnan, China. Geothermal waters contain Ca–HCO₃, Na–HCO₃, and Na (Ca)–SO₄ type, and demonstrate strong rock-related trace elemental distributions. Enhanced water–rock interaction increases the concentration of major and trace elements of geothermal waters. The chemical compositions of geothermal waters in the Rehai geothermal field are very complicated and different because of the magma chamber developed at the shallow depth in this area. In this geothermal field, neutral-alkaline geothermal waters with high Cl, B, Li, Rb Cs, As, Sb, and Tl contents and acid–sulfate waters with high Al, Mn, Fe, and Pb contents are both controlled by magma degassing and water–rock interaction. Geothermal waters from metamorphic, granite, and sedimentary regions (except in the Rehai area) exhibit varying B contents ranging from 3.31 mg/L to 4.49 mg/L, 0.23 mg/L to 1.24 mg/L, and <0.07 mg/L, respectively, and their corresponding δ¹¹B values range from −4.95‰ to −9.45‰, −2.57‰ to −8.85‰, and −4.02‰ to +0.06‰. The B contents of these geothermal waters are mainly controlled by leaching host rocks in the reservoir, and their δ¹¹B values usually decrease and achieve further equilibrium with its surrounding rocks, which can also be proven by the positive δ¹⁸O-shift. In addition to fluid–rock reactions, the geothermal waters from Rehai hot springs exhibit higher δ¹¹B values (−3.43‰ to +1.54‰) than those yielded from other areas because mixing with the magmatic fluids from the shallow magma. The highest δ¹¹B of steam–heated waters (pH 3.25) from the Zhenzhu spring in Rehai is caused by the fractionation induced by pH and the phase separation of coexisting steam and fluids. Given the strong water–rock interaction, some geothermal springs in western Yunnan show reservoir temperatures higher than 180 °C, which demonstrate potential for electricity generation and direct-use applications. The most potential geothermal field in western Yunnan is located in the Rehai area because of the heat transfer from the shallow magma chamber.     

Hydrogeochemical and isotopic composition of a low-temperature geothermal source in northwest Turkey: case study of Kirkgecit geothermal area

Chemical and isotopic compositions of three hot springs and one cold spring in the Kirkgecit geothermal field, located 15 km southwest of Canakkale-Biga in the northwest of Turkey, were monitored five times during 2005 and 2007. The physico-chemical characteristics of the hot springs are average discharge 3–3.5 L/s, surface temperature 45–52°C, pH 8.9–9.3, and electrical conductivity (EC) 620–698 μS/cm. The cold spring has a temperature of 12–13°C, pH 7.5–8.3, and EC 653–675 μS/cm. The hot waters are Na-SO₄ type, whereas the cold water is Ca-HCO₃ type. Chemical geothermometers suggest that the reservoir temperature is around 80–100°C. The isotopic data (oxygen-18, deuterium and tritium) indicate that the thermal waters are formed by local recharge and deep circulation of meteoric waters.     

Hydrogeochemical and hydrogeological investigations of thermal waters in the Usak Area (Turkey)

Thermal waters of the Usak area have temperatures ranging from 33 to 63°C and different chemical compositions. These waters hosted by the Menderes Metamorphic rocks emerge along fault lineaments from two geothermal reservoirs in the area. The first reservoir consists of gneiss, schists, and marbles of the Menderes Metamorphic rocks. The recorded reservoir is Pliocene lacustrine limestone. Hydrogeochemical studies indicate that thermal waters were mixed with surface waters before and/or after heating at depth. The results of mineral equilibrium modeling indicate that all the thermal waters are undersaturated at discharge temperatures for gypsum, anhydrite, and magnesite minerals. Calcite, dolomite, aragonite, quartz, and chalcedony minerals are oversaturated in all of the thermal waters. Water from the reservoir temperatures of the Usak area can reach upto120°C. According to δ¹⁸O and δ²H values, all thermal and cold groundwater are of meteoric origin.     

Geothermal potential evaluation and development prioritization based on geochemistry of geothermal waters from Kangding area,western Sichuan,China

Kangding geothermal area is located in the western Sichuan, belonging to southeastern margin of Tibetan Plateau. Similar to world-renowned south Tibetan and western Yunnan geothermal belt, western Sichuan has intensive surface thermal manifestations including boiling and hot springs. The emerging temperature of thermal waters ranges from 47 to 79 °C with total dissolved solids lying between 899 and 2550 mg/L. δ²H–δ¹⁸O isotopes indicate a meteoric source for the thermal waters and a significant positive oxygen-18 shift in the southern region. It is suggested that southern thermal waters experienced stronger water–rock interaction and are closer to thermodynamic equilibrium, which is also proved by the water type classification. The reservoir temperature calculated by empirical and theoretical chemical thermometry is 180–225 °C for the north and 225–310 °C for the south. Evidences of hydrogeochemistry, stable isotopes, geothermometry and radiocarbon dating indicate that southern region of Kangding area shows greater geothermal potential than the northern region. In addition, based on the hydrogeochemical modeling of mineral saturation, underlying problem of scaling is likely to occur in the study area. According to the results of reservoir temperature, south Kangding sub-district has greater potential in geothermal power generation and development than northern Kangding. Therefore, further exploration and drilling work should give priority to the south Kangding area.