Root properties of vegetation communities and their impact on the erosion resistance of river dikes

Predicted climate change and the associated sea level rise poses an increased threat of flooding due to wave overtopping events at sea and river dikes. To safeguard the land from flooding it is important to keep the soil erosion resistance at the dikes high. As plant roots can be very effective in reducing soil erosion rates by concentrated flow, the main goal of this study is to explore the variability in root system characteristics of five dike vegetation communities along the Scheldt River (Belgium) and to assess their effectiveness in controlling soil erosion rates during concentrated flow. This study is the first one to investigate systematically the erosion‐reducing potential of the root properties of representative dike vegetation communities in a temperate humid climate. Results show that the presence of Urtica dioica resulted in large differences in root length density (RLD) among dike vegetation communities. Observed RLD values in the topsoil ranged from 129 to 235 km m^‐3 for dike vegetation communities without U. dioica, while smaller values ranging from 22 to 58 km m^?3 were found for vegetation communities with U. dioica. The erosion‐reducing effect of the dike vegetation communities was estimated based on a global Hill curve model, linking the RLD to the soil detachment ratio (SDR; i.e. the ratio of the soil detachment rate for root‐permeated topsoils to the soil detachment rate for root‐free topsoils). Concentrated flow erosion rates are likely to be reduced to 13–16% of the erosion rates for root‐free topsoils if U. dioica is absent compared to 22–30% for vegetation communities with U. dioica. Hence, to maintain a high resistance of the soil against concentrated flow erosion it is important to avoid the overgrowth of grassland by U. dioica through an effective vegetation management. Copyright © 2016 John Wiley & Sons, Ltd.     

Non-symmetrical levee breaching processes in a channel bend due to overtopping

A series of experiments were done to reveal the overtopping breaching process of non-cohesive and cohesive levees in a U-bend flume. The flood hydrograph and breaching geometry were measured and analyzed in detail. The results show that the levee breaching processes can be briefly divided into four stages: slope erosion, longitudinal headward gully-cutting, lateral erosion, and relative stabilization. For non-cohesive levees, non-symmetrical lateral development of the breach occurs throughout the four stages, and the final non-symmetrical coefficient is approximately 2.2–2.6. Larger flow discharge or higher water level can accelerate the breaching process, while coarser sands tend to accelerate the process initially but depress the process at the end. The fluvial erosion rate of a non-cohesive breach shows a power-function relation with the excess wall shear stress. For cohesive levees, a plateau forms in the breach partially blocking the flow in the first two stages. The breach flow is approximately perpendicular to the levee body, and, thus, the erosion rates of the two breach sides are almost the same. Non-symmetrical lateral development mainly occurs in the third stage when the deep gully forms. The final non-symmetrical coefficient is approximately 2.7–3.3. It is expected that these findings can provide a valuable experimental dataset and a theoretical basis for breach closure and flood alleviation.     

RILL EROSION PROCESS ON STEEP SLOPE LAND OF THE LOESS PLATEAU

IntheLoessPlateau,alongtheslopelengthfromthetoptothebottom,soilerosionischaracterizedbyobviousverticalzonaldivision,thatis,sheeterosionzone,sheeterosionandrillerosionzone,rillerosionandshallowgullyerosionzoneandgullyerosionzone.Inthesheetandrillero..sionzone,rillerosionamounttakesup70%ofthetotalsoilloss[TANGKenetal.,1983,ZHENGFenlietal.,19871;intherillandshallowgullyerosionzone,rillerosionamountaccountsfor30--40%ofthetotalsoilloss.Sorillerosionisamajorerosionpatternonsteepslopeland.Riller…     

PHENOMENA AND CONTROLLING FACTORS IN DRAWDOWN FLUSHING PROCESSES

IINTRODUCTIONByutilizingthenatUralpowerofflow,hydraulicflushingisaneconomicaltechniquetoremovethedepositedsedimentineitherasettlingbasinorareservoir.Inmanyreservoirsaroundtheworld,hydraulicflushinghasbeenprovenasaneffectivemethodtosustainthereservoirstoragecapacity.Hydraulicflushingprocessesmayinvolveboththeprocessesofscouringpreviousdepositsandpassingincomingsediment-ladenflow,suchasgravitycurrent,throughareservoirtobereleased.Inthisarticle,onlytheformercaseisdiscussed.Thekeythinginthef…     

IMPACTS OF DIMENSION AND SLOPE OF SUBMERGED SPUR DIKES ON LOCAL SCOUR PROCESSES - AN EXPERIMENTAL STUDY

1 INTRODUCTION In alluvial streams bed scour often occurs if the sediment load is less than the transport capacity of the flow. Two types of scour are identified, namely local scour and channel bed scour. Channel bed scour can be further classified accord…     

Experimental study on scour and flow field in a scour hole around a T-shape spur dike in a 90° bend

In this paper results of experimental study on scour and flow field around a T-shape spur dike in a 90 degree channel bend are presented. Experiments were conducted in a laboratory channel to measure the variations of bed topography under a clear water condition. The three dimensional flow field was measured by an Acoustic Doppler Velocimeter in a scour hole due to a T-shape spur dike. It was found that by increasing the Froude number and length of spur dike the amount of scour increases. Increasing the wing length of spur dike decreases the scour. The amount of scour at the upstream of spur dike is much more as compare to that at the downstream of spur dike. By increasing the wing length of spur dike the zone of flow separation expands. As a result the sizes of vortex increase. Details of flow field are also addressed in the paper.     

Significance of sediment transport processes during piedmont floods: the 2005 flood events in Switzerland

A long‐lasting rainstorm event from 20 to 22 August 2005 affected a large part of the northern Alps and Prealps in Switzerland. It resulted in elevated discharges and flooding in many headwater catchments and mountain rivers. The associated geomorphic processes included shallow landslides, deep‐seated slope instabilities, debris flows, and fluvial sediment transport. In many parts of the affected areas human activities are important, including many buildings, traffic lines and other infrastructure. In the steeper parts, geomorphic processes were mainly responsible for flow overtopping and sediment deposition both in and outside of the channel network. In the lower parts, lateral erosion and exceedance of the channel discharge capacity were the main reasons for morphologic channel modification and flooding. Sediment‐related processes contributed a lot to the overall damage. Copyright © 2015 John Wiley & Sons, Ltd.     

PHYSICAL PROCESS BASED SOIL EROSION MODEL IN A SMALL WATERSHED IN THE HILLY LOESS REGION

ＰＨＹＳＩＣＡＬＰＲＯＣＥＳＳＢＡＳＥＤＳＯＩＬＥＲＯＳＩＯＮＭＯＤＥＬＩＮＡＳＭＡＬＬＷＡＴＥＲＳＨＥＤＩＮＴＨＥＨＩＬＬＹＬＯＥＳＳＲＥＧＩＯＮ１ＣＡＩＱｉａｎｇｇｕｏ２ＡＢＳＴＲＡＣＴＡｐｈｙｓｉｃａｌｐｒｏｃｅｓｂａｓｅｄｐｅｒｓｔｏｒｍ...     

EVALUATION OF TOPOGRAPHIC INDICES FOR EPHEMERAL-GULLY EROSION ASSESSMENT

1 INTRODUCTION Erosion caused by ephemeral flows is a frequent phenomenon in nature and contributes to the shape of the landscape. This type of erosion may cause great soil losses in agricultural areas, which are quickly transferred to the watershed outlets through the rill and gully network (Bennett et al., 2000; Poesen et al., 2003). Concentrated flow erosion is controlled by the erodibility of surface materials, climate, soil use and management, and watershed topography. Several metho…     

Rill and ephemeral gully erosion in a small olive grove catchment in Spain: Interactions between management and conservation measures

Concentrated flow erosion in Mediterranean cultivated areas is considered a major process of land degradation. Rills and ephemeral gullies in a 6.4 ha olive orchard catchment located in an intensive commercial farm, which could represent a common degradation scenario in hilly areas, were measured and compared with the sediment loads at the outlet. Four GPS survey campaigns were carried out between March 2009 and March 2014, for periods with cumulative precipitation ranging between 728 and 121 mm. Chopped pruning residues were kept on the lanes during campaigns 2–4, whereas a grass cover crop was seeded in campaign 4. Rainfall, runoff and sediment loads were measured in a flume gauge station at the catchment outlet. The ratio of concentrated flow erosion to catchment sediment load varied between 1.0 and 35.0. Total concentrated flow erosion ranged between 25.0 and 0.1 t ha⁻¹. Rill erosion was the dominant process on ephemeral gullies for three campaigns, with a mean contribution to the total concentrated flow erosion of 55%. Rills clearly followed tractor tracks along the most parallel lanes to the maximum slope. Therefore, a change in traffic direction would be helpful to reduce the connectivity, controlled by the spatial distribution of rows and lanes in the farm. Olive plantation distributions should prioritize hydrological criteria to adapt traffic patterns in olive farms, as long as the tractor manoeuvrability and risk of overturning are not adversely affected. Although the farmer only kept the cover crop for one campaign, it proved to be an efficient measure for interrupting rills along the lanes, whereas pruning residues were effective for the control of interrill erosion. On-site application of pruning residues reduced their handling and transport costs, while increasing the soil fertility and soil cover. However, guidelines for the efficient application of pruning residues are still necessary in terms of residue rates and orientation.     

Dike propagation within active central volcanic edifices: constraints from Somma-Vesuvius,Etna and analogue models

Dikes within stratovolcanoes are commonly expected to have radial patterns. However, other patterns may also be found, due to regional stresses, magmatic reservoirs and topographic variations. Here, we investigate dike patterns within volcanic edifices by studying dike and fissure complexes at Somma-Vesuvius and Etna (Italy) using analogue models. At the surface, the dikes and fissures show a radial configuration. At depths of tens to several hundreds of metres, in areas exposed by erosion, tangential and oblique dikes are also present. Analogue models indicate that dikes approaching the flanks of cones, regardless of their initial orientation, reorient to become radial (parallel to the maximum gravitational stress). This re-orientation is a significant process in shallow magma migration and may also control the emplacement of dike-fed fissures reaching the lower slopes of the volcano.     

Three‐dimensional flow structure and patterns of bed shear stress in an evolving compound meander bend

Compound meander bends with multiple lobes of maximum curvature are common in actively evolving lowland rivers. Interaction among spatial patterns of mean flow, turbulence, bed morphology, bank failures and channel migration in compound bends is poorly understood. In this paper, acoustic Doppler current profiler (ADCP) measurements of the three‐dimensional (3D) flow velocities in a compound bend are examined to evaluate the influence of channel curvature and hydrologic variability on the structure of flow within the bend. Flow structure at various flow stages is related to changes in bed morphology over the study timeframe. Increases in local curvature within the upstream lobe of the bend reduce outer bank velocities at morphologically significant flows, creating a region that protects the bank from high momentum flow and high bed shear stresses. The dimensionless radius of curvature in the upstream lobe is one‐third less than that of the downstream lobe, with average bank erosion rates less than half of the erosion rates for the downstream lobe. Higher bank erosion rates within the downstream lobe correspond to the shift in a core of high velocity and bed shear stresses toward the outer bank as flow moves through the two lobes. These erosion patterns provide a mechanism for continued migration of the downstream lobe in the near future. Bed material size distributions within the bend correspond to spatial patterns of bed shear stress magnitudes, indicating that bed material sorting within the bend is governed by bed shear stress. Results suggest that patterns of flow, sediment entrainment, and planform evolution in compound meander bends are more complex than in simple meander bends. Moreover, interactions among local influences on the flow, such as woody debris, local topographic steering, and locally high curvature, tend to cause compound bends to evolve toward increasing planform complexity over time rather than stable configurations. Copyright © 2016 John Wiley & Sons, Ltd.     

Processes,spatio‐temporal factors and measurements of current erosion in the French Southern Alps: a review

Present erosion in mountainous areas of Western Europe causes land management problems, particularly for areas located downstream of erosion zones. Except for transalpine roads and ski resorts, economic activities no longer require as much space as they did in the past. Therefore, natural reforestation has provided signi?cant protection for alpine hillslopes during the 20th century. However, extreme ?oods continue to cause severe damage in intra‐alpine valleys, as well as in piedmont and surrounding plains, making the study of present water erosion phenomena very important. Many studies have investigated the processes and factors of water erosion on slopes at both the catchment and plot scales. They have focused on rock fragmentation and transportation in different ?elds, the spatial and temporal explanatory variables, the consequences downstream (?ooding, sedimentation, river bed evolution) and the impact of ?oods. In the French Alps, present erosion has been studied in a variety of outcrops, with several recent studies conducted in ?elds such as marls, clayey deposits, molasses and moraines. These kinds of outcrops are found throughout the alpine massif, including an area of special interest on the great Jurassic black marl outcrop where badlands are frequently observable. Geomorphologists and hydrologists have been particularly interested in the strong erosion processes in marls, seeking to determine the main patterns and the impact of spatial and temporal factors on soil loss quantities. The main climatic factors of rock disaggregation were found to be the freeze–thaw and wet–dry cycles, which destroy rock cohesion, and the splash effect of rain. The principal site variables are vegetation cover, exposure and dip–slope angle. Erosion rates are two or three orders of magnitude higher on bare soils than on pastures; northern aspect slopes suffer two to four times as much soil loss as southern aspect slopes. Finally, the angle formed by the slope and the dip also determines different behaviours: erosion rates are higher when slope and dip are perpendicular than when they are parallel. The transportation agents are mostly debris ?ows and runoff caused by intense precipitation. Annual erosion depth in the marls is generally assumed to be substantial, up to 10 mm. The high value can be explained by the severity of the climatic conditions and the brittleness of the lithology, which results in numerous fractures. Copyright © 2003 John Wiley & Sons, Ltd.     

DIKE FORMATION WITH SUBMERGED VANE

1 INTRODUCTION Increasing capital costs, emerging environmental concerns and rising maintenance expenses of conventional river training works around the world have led to the development of submerged vanes in practice. Submerged vanes are being favoured f…     

EXPERIMENTAL INVESTIGATIONS AND NUMERICAL SIMULATIONS OF REDUCING SECONDARY FLOWS AROUND A SPUR DIKE

1 INTRODUCTION The Yangtze River at the Three Gorges Project (TGP) site meanders with a complex morphology, including ridges like Jiuling Hill that projects into the approach navigation channel (Fig. 1). The approach navigation channel consists of a 530-m…     

How sediment composition and flow rate influence downstream channel morphodynamics upon dam removal

The process of dam removal establishes the channel morphology that is later adjusted by high-flow events. Generalities about process responses have been hypothesized, but broad applicability and details remain a research need. We completed laboratory experiments focused on understanding how processes occurring immediately after a sediment release upon dam removal or failure affect the downstream channel bed. Flume experiments tested three sediment mixtures at high and low flow rates. We measured changes in impounded sediment volume, downstream bed surface, and rates of deposition and erosion as the downstream bed adjusted. Results quantified the process responses and connected changes in downstream channel morphology to sediment composition, temporal variability in impounded sediment erosion, and spatial and temporal rates of bedload transport. Within gravel and sand sediments, the process response depended on sediment mobility. Dam removals at low flows created partial mobility with sands transporting as ripples over the gravel bed. In total, 37% of the reservoir eroded, and half the eroded sediment remained in the downstream reach. High flows generated full bed mobility, eroding sands and gravels into and through the downstream reach as 38% of the reservoir eroded. Although some sediment deposited, there was net erosion from the reach as a new, narrower channel eroded through the deposit. When silt was part of the sediment, the process response depended on how the flow rate influenced reservoir erosion rates. At low flows, reservoir erosion rates were initially low and the sediment partially exposed. The reduced sediment supply led to downstream bed erosion. Once reservoir erosion rates increased, sediment deposited downstream and a new channel eroded into the deposits. At high flows, eroded sediment temporarily deposited evenly over the downstream channel before eroding both the deposits and channel bed. At low flows, reservoir erosion was 17–18%, while at the high flow it was 31–41%.     

One-dimensional morphodynamic model for retrogressive erosion based on a sediment entrainment theory at high flow velocity

Retrogressive erosion is a high-speed erosion process that usually occurs during the rapid release of stored water in reservoirs built on sandy rivers.Retrogressive erosion has been utilized in the practice of reservoir sedimentation control,but accurate prediction of the bed deformation process by numerical models has rarely been reported.The current study presents a one-dimensional morphodynamic model for simulating the evolution process of retrogressive erosion induced by high-velocity flows on steep slopes.The governing equations apply a Cartesian coordinate system with a vertically oriented z axis.The bed surface gradient and friction terms in the flow equations include correction factors to take account of the effects of high slope on flow movement.The net vertical sediment flux term in the sediment transport and bed deformation equations is calculated using an equation of erosion velocity.Particularly,this equation is based on an empirical relation between the sediment entrainment rate and the Shields parameter in contrast to the traditional sediment transport capacity,and the critical Shields parameter is modified by taking into account the permeability of the sediment layer and the stability of particles on a slope.The feedback of scoured sediment on the flow movement is considered by additional terms in the governing equations.Flume experiments of retrogressive erosion in literature were simulated to validate the model.The temporal variations of the longitudinal profiles of the free surface and channel bed and the sediment transport rate were well predicted.The algorithm calculating sediment entrainment in the proposed model also was validated for an experiment measuring entrainment rate from the literature.More importantly,it was found that the morphodynamic model using the sediment transport capacity equation predicts the trend of cumulative erosion contrary to the measurements,while results of the proposed model can follow a similar trend with the observed data in the retrogressive erosion process.     

Loess erosion change modeling during heavy rainfall

A typical gully sub-basin with a complex geomorphological form is used to do a model test of gravity erosion of loess by considering the sequence of slopes in a prototype gully creating a sequence of underlying surface forms in the upper reaches. The results show that the runoff from heavy rainfall is the main external force for the erosion of loess, and also is an important influencing factor to stimulate and intensify the development of gravity erosion. The soil structure and the height of the...     

Bed scour by debris flows: experimental investigation of effects of debris‐flow composition

Debris flows can grow greatly in size by entrainment of bed material, enhancing their runout and hazardous impact. Here, we experimentally investigate the effects of debris‐flow composition on the amount and spatial patterns of bed scour and erosion downstream of a fixed to erodible bed transition. The experimental debris flows were observed to entrain bed particles both grain by grain and en masse, and the majority of entrainment was observed to occur during passage of the flow front. The spatial bed scour patterns are highly variable, but large‐scale patterns are largely similar over 22.5–35° channel slopes for debris flows of similar composition. Scour depth is generally largest slightly downstream of the fixed to erodible bed transition, except for clay‐rich debris flows, which cause a relatively uniform scour pattern. The spatial variability in the scour depth decreases with increasing water, gravel (= grain size) and clay fraction. Basal scour depth increases with channel slope, flow velocity, flow depth, discharge and shear stress in our experiments, whereas there is no correlation with grain collisional stress. The strongest correlation is between basal scour and shear stress and discharge. There are substantial differences in the scour caused by different types of debris flows. In general, mean and maximum scour depths become larger with increasing water fraction and grain size, and decrease with increasing clay content. However, the erodibility of coarse‐grained experimental debris flows (gravel fraction = 0.64) is similar on a wide range of channel slopes, flow depths, flow velocities, discharges and shear stresses. This probably relates to the relatively large influence of grain‐collisional stress to the total bed stress in these flows (30–50%). The relative effect of grain‐collisional stress is low in the other experimental debris flows (<5%), causing erosion to be largely controlled by basal shear stress. Copyright © 2016 John Wiley & Sons, Ltd.     

‘Local gradient’ and between‐site variability of erosion rate on badlands in the Karoo,South Africa

Site‐average values of local gradient, defined as the steepest slope angle measured at a point, are a powerful predictor of long‐term rates of soil loss as measured by erosion pins on the non‐channel floor portions of ten badland study sites in the Karoo area of South Africa. Local gradient may be easily measured using a smartphone clinometer. The successful use of local gradient here is in strong contrast to the previous failure of other site‐specific attributes, including other measures of gradient and relief, to explain between‐site variation in erosion rate on these study sites. Each measurement of local gradient may be thought of as a sample of the site's microtopography. Microrelief is a strong determinant of the emergent patterns of inter‐channel overland flow, and hence of the patterns of inter‐channel erosion by flow. Local gradient changes most rapidly during the initial stages of channel incision. When channels are established, local gradient changes more slowly leading to almost‐parallel retreat of channel sidewalls. A sensitivity analysis suggests that measurements of local gradient are not all equal with regard to prediction of long‐term erosion rate. A greater share of predictive power is contributed by measurements made on very steep or vertical channel side wall areas, and a lesser share is contributed by measurements made on interfluves. Copyright © 2017 John Wiley & Sons, Ltd.