动扭剪试验中砂土液化后流动特性分析

土体在初始液化后仍然可能承受动荷载作用发生大变形。引入流体力学中的剪应变率和表观黏度的概念,对振动扭剪试验中饱和砂土液化后的流动特性进行了分析。分析中将砂土的状态分为0有效应力状态和非0有效应力状态。结果表明,砂土在0有效应力状态下表现出与静扭剪试验类似的“剪切稀化”非牛顿流体的特征,表观黏度随着剪应变率的增大而减小。加载周数对“剪切稀化”状态下的剪应变率幅值有影响,随着加载周数的增加,剪应变率幅值逐渐增大,而对流动曲线的形状没有影响。在非0有效应力状态下,砂土的表观黏度随应变的增大而增大,随孔压比的减小而增大,且所有的试验得到的表观黏度与孔压比具有一致关系。     

基于单相流的减饱和砂土流固耦合改进算法

减饱和法是一种通过减小饱和砂土地基中水的饱和度来处置可液化砂土地基的方法。基于单相流-固耦合理论,将减饱和砂中水-气两相流体等效为单相流体,提出一种可以考虑加载过程中孔隙流体体积模量变化的减饱和砂土静态液化的单相流改进算法,用其进行单调荷载作用下三轴不排水压缩试验数值模拟研究,分析了不同饱和度条件下的减饱和砂土的不排水反应并与饱和砂土三轴不排水试验结果进行对比。研究结果表明,单相流改进算法能够很好地反映减饱和法的抗液化特性。此外,对比不同数值分析方法模拟结果,得出以下结论：采用单相流简化算法分析减饱和砂土的不排水反应时,因为不考虑加载过程中的孔隙流体体积模量变化,所以初始的流体体积模量取值会影响减饱和砂土的强度,初始围压为100 kPa、饱和度为96%的减饱和砂土在单调荷载作用下,气体体积模量取值从100 kPa增加至200 kPa时,减饱和砂试样的峰值偏应力会减小约30%,孔隙压力会增加约40%;通过对比同等条件下的单相流改进算法和两相流算法的应力-应变关系曲线以及饱和度和体积应变变化曲线,两者结果相近,误差在5%以内。综上所述,单相流改进算法是一种较为合理而简洁地模拟减饱和砂土静态液化的计算方法。     

The effective stress concept and the evaluation of changes in pore air pressure under jacketed isotropic compression tests for dry sand based on the 2‐phase porous theory

The effective stress concept for solid‐fluid 2‐phase media was revisited in this work. In particular, the effects of the compressibility of both the pore fluid and the soil particles were studied under 3 different conditions, i.e., undrained, drained, and unjacketed conditions based on a Biot‐type theory for 2‐phase porous media. It was confirmed that Terzaghi effective stress holds at the moment when soil grains are assumed to be incompressible and when the compressibility of the pore fluid is small enough compared to that of the soil skeleton. Then, isotropic compression tests for dry sand under undrained conditions were conducted within the triaxial apparatus in which the changes in the pore air pressure could be measured. The ratio of the increment in the cell pressure to the increment in the pore air pressure, m, corresponds to the inverse of the B value by Bishop and was obtained during the step loading of the cell pressure. In addition, the m values were evaluated by comparing them with theoretically obtained values based on the solid‐fluid 2‐phase mixture theory. The experimental m values were close to the theoretical values, as they were in the range of approximately 40 to 185, depending on the cell pressure. Finally, it was found that the soil material with a highly compressible pore fluid, such as air, must be analyzed with the multi‐phase porous mixture theory. However, Terzaghi effective stress is practically applicable when the compressibilities of both the soil particles and the pore fluid are small enough compared to that of the soil skeleton.     

An experimental investigation of gravity-driven shale tectonics in progradational delta

Many deltas exhibit gravitational deformation of their sedimentary cover. In these systems, the décollement layers do not always consist of rock salt but sometimes of overpressured shale. Unlike salt, the efficiency of detachment in shale depends on the magnitude of fluid overpressures and it varies through time and space, as rapid sedimentary burial progrades into deeper water. As a result, the gravity deformational domains are progressively translated seaward. Sandbox models involving high air pore pressures were used to simulate such gravity-driven shale tectonics in prograding deltas. Models were built with sand of various permeabilities and air was injected to simulate the mechanical effects of fluid overpressure. Our apparatus for the injection of air allowed us to control subsurface pressures in space and time during the experiments, and it was used to simulate the advance of the front of the overpressured domain during the sedimentary progradation. In our models, sand kept obeying a frictional behavior, for medium to high pore pressures, and the detachment appeared as very thin shear bands. Compressional belts that formed during the experiment were dominated by asymmetric basinward-verging fore-thrusts, as is often observed in deep-water, shale-detached foldbelts. Where the value of fluid pressures approached that of the lithostatic stress, sand was fluidized, resulting in ductile strains analogous to what occurs in highly overpressured mobile shale. During progradation, ancient buried thrustbelts were reactivated, thereby controlling later extension. During the experiments, sand volcanoes, analogous to mud volcanoes, formed in relation with tectonic structures. Some of them developed near normal faults but many of them formed directly above old buried thrusts.     

饱和悬浮塑料砂流动变形可视环剪试验研究

为了分析剪切条件下零有效应力状态砂土的流动变形规律,对传统环剪仪进行了试样可视化改造,研制了透明环形剪切盒,通过对剪切盒膨胀性能分析及与标准砂的剪切试验对比,验证了环剪装置改造的合理性。通过分析不排水条件下饱和悬浮塑料砂的剪应力-应变曲线,发现其剪切强度具有应变软化的特性。通过分析环剪仪中饱和悬浮塑料砂试样的有效应力,证实了可视环剪试验中的土体基本处于零有效应力状态。开展了饱和悬浮塑料砂的流动变形可视环剪试验研究,结果表明：饱和悬浮塑料砂在固结不排水条件下剪切变形不连续,直接在剪切面发生断裂;在不固结不排水的条件下饱和悬浮塑料砂的剪切变形表现出流动形态,且与剪切速率有关：在低剪切速率下,剪切变形仅在剪切面处形成具有曲线轨迹的流动变形而在其他区域不发生变形;而在高剪切速率下剪切变形为整体的倾斜变形,符合黏性流体的流动变形特征。     

Petrology of a portion of the Eastern Peninsular Ranges mylonite zone,Southern California

Peraluminous and metaluminous plutonic rocks of the Peninsular Ranges batholith near Borrego Springs in southern California were mylonitized in the large shear zone known as the eastern Peninsular Ranges mylonite zone (EPRMZ). Accompanying mylonitization in this portion of the EPRMZ was metamorphism at intermediate-low-pressure amphibolite-facies conditions. Deformation in the zone overlapped in time with Cretaceous intrusion of the batholith. In the San Ysidro Mountain — Pinyon Ridge area, four north-south trending zones of differing intensity of deformation have been defined; from east to west the degree and style of deformation gradually change from undeformed or weakly deformed rocks to strongly mylonitized rocks. Electron microprobe analysis shows that recrystallized hornblende, biotite, and plagioclase are variable in composition, probably reflecting a range of metamorphic conditions accompanying deformation. Comparison of mineral compositions with those from mafic schists of Vermont suggests conditions ranged from andalusite-staurolite through sillimanite-muscovite grades as defined for pelitic rocks. Stability of muscovite+quartz in mylonite assemblages and lack of remelting of granitic rocks indicate that temperature did not exceed about 650° C during mylonitization and lithostatic pressure did not exceed about 5 kbar. Over time, any given rock volume experienced a range of temperature, lithostatic pressure, and perhaps fluid pressure and differential stress. Mineral reactions in the zone involved hydration, requiring introduction of water. The possibility of large-scale migration of K and Fe is suggested by whole-rock chemical data. Brittle and ductile deformation features are closely associated in one part of the EPRMZ. The combined evidence suggests the presence of a pore fluid with fluid pressure close to lithostatic pressure. Short periods of low fluid pressure and possible high differential stress cannot be ruled out.     

三轴试样钻孔灌砂固结排水效果试验研究

对渗透性较差的重黏土样进行固结排水试验时,其饱和、固结、剪切过程时间较长。为提高固结排水试验效率,改进了三轴排水工艺,提出在试样中钻孔灌砂形成竖向排水通道,并进行了针对黏土样的固结排水试验的验证。试验结果表明,1 %～3 %置换率的砂井对固结排水试验应力-应变无影响,并有利于加速三轴试样的饱和、固结排水、孔压消散、剪切排水过程,可使试验效率提高5倍以上;试样周边、顶面、底面粘贴滤纸条,再结合试样内部钻孔灌砂,是改善三轴试验排水路径的一种科学合理的、高效的方法,能够获得准确、可靠的E-B模型参数。     

孔隙水压力对岩石裂纹扩展影响的数值模拟

应用岩石破坏过程渗流-应力-损伤(FSD)耦合分析软件F-RFPA2D,通过对孔隙水压作用下岩石试件加载破坏过程的数值模拟,对孔隙水压力大小和梯度对岩石试样中裂纹的萌生和扩展进行了数值模拟研究。模拟结果再现了孔隙水压力作用下裂纹萌生扩展的全过程,表明孔隙水压力大小和梯度对岩石中裂纹的萌生和扩展模式都有很大的影响。     

液化后砂土流体特性测试装置的研发及试验研究

为研究液化砂土的流动变形特征,开展了液化砂土的流体特性试验研究。基于边界层理论研发一套液化砂土表观黏度测试装置,主要由调速电机、电机调速器、圆柱转子、扭矩传感器等部分组成,该装置能有效测试液化砂土的表观黏度;开展了不同孔压比、转速下饱和砂土表观黏度及圆柱转子所受摩擦力矩特性研究,着重分析了液化后砂土的表观黏度特性。结果表明,液化前孔压发展及液化后孔压消散阶段摩擦力矩均受到孔压比及转速的影响;液化后砂土孔压逐渐消散,强度恢复,流动能力衰减,表观黏度升高,表观黏度与孔压比呈现出一定的线性相关性;表观黏度随着剪应变率的增大而降低,且两者呈现出幂函数关系,表明液化后砂土具有典型幂律型剪切稀化非牛顿流体特征。     

常温下砂岩的变形特征及其影响因素

本文研究了常温下砂岩的变形特征，发现低围压条件下。砂岩表现为脆性剪切破裂，并产生扩容现象，而在高围压条件下，则表现为塑性流动，在塑性流动过程中，孔隙破裂，砂粒被压碎。并发生旋转和滑动，砂岩体积收缩，并表现为应变硬化，在砂岩由脆性剪切破裂向塑性流动的转化过程中，砂岩的孔隙率和围压起了关键的作用，本文还研究了砂岩孔隙破裂的机制，随着围压的增加，孔隙破裂分为两个阶段；第一阶段是孔隙边缘的剪切破裂，第二阶     

陕西泾阳东风高速远程黄土滑坡运动过程的模拟

陕西泾阳南塬的东风滑坡是一个典型的高速远程黄土滑坡,由于斜坡顶部的黄土台塬长期灌溉所诱发。通过野外调查,采取滑坡后缘斜坡的黄土试样,对斜坡中部的Q2黄土做天然含水率的固结不排水剪试验,对斜坡底部地下水位面附近的Q1黄土做饱和固结不排水剪试验,结果表明非饱和的Q2黄土和饱和的Q1黄土在破坏后都具有显著的应力降,但前者是由结构强度引起,而后者则是由剪切形成的超孔隙水压力引起,由此表明该斜坡一旦破坏,就会有较高的启动速度。对滑坡坡脚以外一级阶地上的砂卵层做环剪慢剪试验,测得其有效残余摩擦角,根据滑坡各部分含水状态给定孔隙水压力参数,利用Sassa. K滑坡运动模型对该滑坡运动过程进行模拟,从模拟结果反映出滑坡运动过程中的覆盖范围和速度的变化,模拟的滑坡运动距离和覆盖范围与实测比较吻合,最高速可达到37m s-1,为高速滑坡。黄土滑坡以高的初速度下滑到坡脚下一级阶地上的饱和砂卵层上,砂卵层上液化是导致其远程运动的主要原因。     

Effects of initial static shear on cyclic resistance and pore pressure generation of saturated sand

In practical engineering, cyclic shear stresses induced by earthquakes, traffic, and waves are superimposed on the initial static shear stress in sand fills or deposits, leading to complex responses of soils such as their deformation characteristics, pore pressure generation, and susceptibility (or cyclic resistance) to liquefaction. To experimentally investigate the undrained cyclic response of saturated sand, a series of triaxial tests were performed, covering a broad range of initial static and cyclic deviatoric stress levels. The results indicate that different stress conditions lead to two types of cyclic behavior: cyclic mobility and residual deformation accumulation. The compressional static stress is beneficial to the cyclic resistance of the dense sand, whereas the extensional static stress is regarded as detrimental as it tended to reduce the cyclic strength. Moreover, by comparing the available test data obtained from the same sand with varying initial densities and confining pressures, the static shear effect on cyclic resistance was found to be dependent on the state of the sand. Compared to the interpretation made using the limiting pore pressure-based criterion, the conventional failure criterion using a cyclic axial strain of 5% may lead to a substantial overestimation of the cyclic resistance, thus resulting in unsafe assessment and design. Hence, by employing the pore pressure criterion, the pore pressure generated in the cyclic tests was investigated and was found to be significantly influenced by the static shear stress. A pore pressure generation model is proposed to obtain the pore pressure characteristics of sand under various static shear stress conditions.     

Stress-strain behaviour of reconstituted illitic clay at different temperatures

Tests on specimens of reconstituted illitic clay have examined the influence of temperature on the mechanical behaviour of clay soils. The program involved consolidation to effective confining pressures up to 1.5 MPa, heating to 100°C, and tests on normally consolidated and overconsolidated specimens with OCR = 2. The tests included isotropic consolidation, undrained triaxial compression with pore water pressure measurement, drained tests along controlled stress paths to investigate yielding behaviour, and undrained tests which involved heating and measurement of the resulting induced pore water pressures. The large strain strength envelope is independent of temperature. However, peak undrained strengths increase with temperature because smaller pore water pressures are generated during shearing. An important contribution from the study is a series of results for the yielding of illitic clay at three different temperatures. For the first time, there is clear evidence of yield loci decreasing in size with increasing temperature. An associated flow rule can be assumed without serious error. The results contribute to the confirmation of a thermal elastic-plastic soil model developed by the authors from cam clay following the addition of a small number of extra assumptions. Depending on the initial stress state, heating under undrained conditions may produce shear failure.     

成矿流体动力学的原理、研究方法及应用

流体流动是热液成矿作用不可或缺的一部分,其研究是建立成矿模式的重要组成部分。成矿流体动力学主要研究流体流动的驱动力、压力状态、流速、流动方向以及它们与矿床定位的关系。文中总结了成矿流体动力学的基本原理和方法,并对其在成矿作用研究和矿产勘查上的重要性和局限性进行了讨论。流体流动的驱动力可以是流体的超压、地势差、构造变形以...     

斜椭圆应力路径下饱和松砂动力特性试验研究

利用空心圆柱扭剪仪模拟斜入射地震波作用形成的斜椭圆应力路径,对比研究了等向固结条件下饱和福建标准松砂在循环斜椭圆、圆形、扭剪、三轴路径下的动力特性。试验研究表明：土体循环孔压发展存在陡升型和陡降型两种模式;圆形路径下累积孔压增长速率最快,循环扭剪最小;归一化孔压与斜椭圆的倾角无关,但受斜椭圆长短轴比及动应力比影响。砂土的不排水动强度与动应力路径密切相关,循环扭剪和循环三轴最大,循环斜椭圆次之,圆形路径最小。地震波从特定角度入射时,形成近似圆形路径,若只将地震波视为垂直入射的S波,将高估地基土体抗液化强度。     

基于南水模型的钙质砂应力−应变关系模拟

钙质砂是一种海洋生物成因的特殊岩土材料,具有颗粒性状不规则、易破碎的特点,表现出与石英砂不同的力学性质。为模拟钙质砂在不同应力水平下的应力?应变关系,首先分析南水模型的不足：即无法描述应力不变情况下应变无限增长的特点和不能描述钙质砂的剪胀性;然后通过在切线模量中引入应力比与峰值应力比的比值,合理考虑了颗粒破碎的影响;提出了切线模量和切线体积比与应力比间的函数关系式,使得改进后的模型能较好地描述应变?体变关系。同时,将孔隙压力系数引入到孔隙压力表达式中,较好地模拟了三轴不排水剪切试验结果。与现有的模型相比,改进后的模型表达式简单易懂,参数获取更为方便。     

不同排水条件下砂-黄土界面的剪切力学特性

为了研究异质土在不同排水条件下的力学机理,进行了一系列环剪试验,对单一黄土、单一砂、砂-黄土组成的异质土在剪切力学特性上的差异及其产生机理进行了比较分析。结果表明：在不同排水条件下,砂-黄土组成的异质土在相互接触剪切的过程中,剪切应力变化形态和抗剪强度与单一黄土、单一砂之间存在显著差异,即砂-黄土组成的异质土在其剪切过程中呈现出了黏性土的剪切力学特征;在相同剪切速率条件下,砂-黄土组成的异质土在不同排水条件下的抗剪强度比单一黄土和单一砂的抗剪强度至少降低了71%和51%。不同排水条件下砂-黄土的剪切力学性质出现了差异,其主要原因与剪切面处砂与黄土之间的相互作用以及剪切面处土体内孔隙水状态有关。     

泡沫钻进流体循环用消泡器设计与数值模拟分析

高效、经济、环保的消泡技术是泡沫钻进流体循环利用的基础。根据气体引射器原理,设计了一种新型旋内喷式机械消泡装置,以压缩空气为动力介质,联合真空负压、冲击剪切、充气饱和及减速增压扩散4种作用方式快速消泡,实现泡沫流体的循环利用。利用计算流体动力学软件FLUENT对消泡器内部速度和压力流场进行了数值模拟分析,结果表明：旋内喷式消泡器内部产生两个相邻重叠的真空负压区域,能够对外界流体产生巨大的抽吸力,抽吸量是入口压缩空气质量流的1.6倍左右;当入口压缩空气的质量流为0.1 kg/s时,消泡器中心最大负压值达到了21 kPa;在交汇式喷射孔的多股射流交汇碰撞点附近,由于速度的提升,形成了一个更大的负压区域,对消泡产生积极作用。     

钙质砂声发射特征的三轴试验研究

钙质砂在低应力水平下就会产生颗粒破碎,并伴随有明显的声发射。在不同围压下,对不同初始孔隙比和级配的南沙群岛永暑礁钙质砂进行室内三轴排水剪切试验,同时监测其声发射信号。试验发现：当围压增加或初始孔隙比减小时,钙质砂偏应力峰值逐渐增加,但在某一界限围压时,声发射活动出现最强,在某一界限孔隙比附近时,声发射活动出现最弱;对于级配较差的钙质砂,试验前期声发射活动较弱,其偏应力峰值较小。