Efficient removal of hexavalent chromium from aqueous solutions using autohydrolyzed Scots Pine (Pinus Sylvestris) sawdust as adsorbent

In this work, a low-cost lignocellulosic adsorbent with high biosorption capacity is proposed, suitable for the efficient removal of hexavalent chromium from water and wastewater media. The adsorbent was produced by autohydrolyzing Scots Pine (Pinus Sylvestris) sawdust. The effect of the autohydrolysis conditions, i.e., pretreatment time and temperature, on hexavalent chromium biosorption was investigated using energy-dispersive X-ray spectroscopy (EDS) and UV–visible spectrophotometry. The Freundlich, Langmuir, Sips, Radke-Prausnitz, Modified Radke-Prausnitz, Tóth, UNILAN, Temkin and Dubinin-Radushkevich adsorption capacities and the rate constant values for pseudo-first- and pseudo-second-order kinetics indicated that the autohydrolyzed material exhibits significantly enhanced hexavalent chromium adsorption properties comparing with the untreated sawdust. The Freundlich’s adsorption capacity K _F increased from 2.276 to 8.928 (mg g^?1)(L mg^?1)^1/n , and the amount of hexavalent chromium adsorbed at saturation (Langmuir constant q _m) increased from 87.4 to 345.9 mg g^?1, indicating that autohydrolysis treatment at 240 °C for 50 min optimizes the adsorption behavior of the lignocellulosic material.     

Determination of perchlorate and iodide concentrations in edible seaweeds

Perchlorate and iodide concentrations were determined in brown (Undaria pinnatifida and Laminaria japonica) and red (Porphyra sp.) edible seaweeds, which are commonly consumed by Korean people, with the use of ion chromatography, coupled with a tandem mass spectrometer. Seaweeds (i.e., good sources of iodine) are among the most important plant life in the ocean and commonly consumed as food and nutritional supplement in South Korea. All seaweed samples were purchased from different regions in South Korea. The detected concentrations of perchlorate were as follows: 19.7–620.7 μg kg^?1 dry weight (n = 11, mean concentration = 149.2 μg kg^?1 dry weight) for L. japonica and 7.3–21.7 μg kg^?1 dry weight (mean concentration = 10.6 μg kg^?1 dry weight) for U. pinnatifida. Of the 11 samples of Porphyra sp., only 1 sample showed 6.7 μg kg^?1 dry weight perchlorate. The concentrations of iodide in all seaweed samples varied from 0.44 to 6,800 mg kg^?1 dry weight. L. japonica samples (n = 11) had significantly higher iodide concentrations, with a mean of 5,261 mg kg^?1 dry weight. The bioconcentration factor values for perchlorate and iodide in the three different seaweeds varied widely and showed similar variation trends. The trend for perchlorate and iodide was Porphyra sp. < U. pinnatifida < L. japonica. The results have provided growing evidence that perchlorate frequently occurs in food products.     

Specific detection of bioavailable phenanthrene and mercury by bacterium reporters in the red soil

Genetically engineered Pseudomonas putida reporters (BMB-PL and BMB-ME), which, respectively, carried phnS-luxCDABE and merR-egfp cassette, were used to determine bioavailable phenanthrene and mercury. Over a spiked range of concentrations and aged for 6 days in red soil samples, the reporters were tested to determine the optimal assay conditions and the bioavailable phenanthrene (0–60 mg kg^?1) and Hg²⁺ (0–240 μg kg^?1) were evaluated by the signal of the relative fluorescent units and relative luminescence units. Single contamination was carried out and good correlations were obtained between signal strength and pollutant concentrations, whereas interference and bioavailability repression were observed in dual-contamination experiments. Other heavy metal ions at nanomolar level did not interfere with BMB-ME measurement while BMB-PL showed some response to other polycyclic aromatic hydrocarbons or their intermediate products during degradation. Comparing high-performance liquid chromatography methods with the bacterial reporters, both BMB-ME and BMB-PL appeared to have a detection limit (mercury <40 μg kg^?1; phenanthrene <24 mg kg ^?1) similar to the instrumental analysis. Although physical parameters may affect the interaction of pollutants with bioreporter cells, advantages include the inherent biological relevance of the response, rapid response time, and potential for field deployment. Our results strongly suggest that the BMB-ME and BMB-PL bioreporters constitute an adaptable system for easily detecting the bioavailability of mercury and phenanthrene in the red soils.     

Impact of parent rock and topography aspect on the distribution of soil trace metals in natural ecosystems

The concentration and dynamic of soil trace metals in natural ecosystems, in particularly, is dependent on the lithology of parent rock as well as topography and geopedological processes. To ascertain more knowledge for this dependency, soils on three parent rocks involving peridotite, pegmatite, and dolerite in two contrasting topography aspects were investigated. The total values of Fe, Mn, Zn, Cu, and Ni were determined and compared for different soil pedons. The concentration of Fe, Mn, and Ni were highest in soils developed from peridotite (127, 1.8 g kg^?1, and 218 mg kg^?1, respectively), intermediate in soils derived from dolerite (81, 1.3 g kg^?1, and 166 mg kg^?1, respectively), and least in soil developed from pegmatite (50, 0.23 g kg^?1, and 20 mg kg^?1, respectively). The values of Zn and Cu, originated from different parent rocks, were in order of dolerite (78 mg kg^?1) > peridotite (77 mg kg^?1) > pegmatite (28 mg kg^?1) and pegmatite (121 mg kg^?1) > peridotite (111 mg kg^?1) > dolerite (28 mg kg^?1), respectively. For most of the studied pedons, profile metals distribution differed among the soils: The values of Fe, Cu, and Ni were enriched in the cambic horizons mainly as result of release, mobilization, and redistribution of the studied metals during geopedological processes, whereas those of Zn and Mn were concentrated in the surface horizons. Probably due to greater weathering rate of trace metal-bearing rocks on north-facing slope, the content of the trace metals along with the geoaccumulation index (I _geo) and the degree of soil contamination (C _d) were higher than on south-facing slope. Based on assessment of soil pollution indices, the soils were categorized as unpolluted [I _geo ≤ 0 (class 0)], unpolluted to moderately polluted levels [0 < I _geo < 1 (class 1)], and very low [C _d < 1.5 (class 0)] to low degree of contamination [1.5 < C _d < 2 (class 1)].     

Ionic solid-impregnated sulphate-crosslinked chitosan for effective adsorption of hexavalent chromium from effluents

Microwave-assisted tetrabutyl ammonium-impregnated sulphate-crosslinked chitosan was synthesized for enhanced adsorption of hexavalent chromium. The adsorbent obtained was extensively characterized using Fourier transform infrared, X-ray diffraction, scanning electron microscopy and energy-dispersive X-ray studies. Various isotherm models such as Langmuir, Freundlich and Dubinin–Radushkevich were studied to comprehend the adsorption mechanism of hexavalent chromium by the adsorbent. Maximum adsorption capacity of 225.9 mg g^?1 was observed at pH 3.0 in accordance with Langmuir isotherm model. The sorption kinetics and thermodynamic studies revealed that adsorption of hexavalent chromium followed pseudo-second-order kinetics with exothermic and spontaneous behaviour. A column packed with 1 g of adsorbent was found to give complete adsorption of Cr(VI) up to 900 mL of 200 mg L^?1 solution which discerns the applicability of the adsorbent material for higher sample volumes in column studies. The effective adsorption results were obtained due to both ion exchange and ion pair interaction of adsorbent with hexavalent chromium. Greener aspect of overall adsorption was regeneration of the adsorbent which was carried out using sodium hydroxide solution. In the present study, the regenerated adsorbent was effectively reused up to ten adsorption–desorption cycles with no loss in adsorption efficiency.     

Formation of one-dimensional composites of poly(<Emphasis Type="Italic">m</Emphasis>-phenylenediamine)s based on <Emphasis Type="Italic">Streptomyces</Emphasis> for adsorption of hexavalent chromium

Here, a novel one-dimensional composite of poly(m-phenylenediamine)s coating on filamentous Streptomyces was successfully constructed via a controllable polymerization reaction. The synthesized composites were characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. Their adsorption isotherm and kinetics for aqueous hexavalent chromium were also systematically examined. The results of scanning electron microscopy analysis indicated that the obtained composites based on Streptomyces were showed a uniform and stable one-dimensional morphology with distinct core–shell configuration. Moreover, the Langmuir isotherm model (R ² > 0.96) and pseudo-second-order equation (R ² = 0.9996) described well the equilibrium adsorption behavior and kinetics of hexavalent chromium adsorption by the composites. In addition, bath adsorption experiments demonstrated the highest adsorption capacity of hexavalent chromium by the composites reached 320.03 mg g^?1 in an acid solution, which was 5.6 times as that of the pure Streptomyces filaments. The results of Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy analyses suggested that the adsorption of hexavalent chromium by the composites possibly involved the protonation, redox, and chelation reactions. Therefore, a promising application of these composites in treating acid hexavalent chromium-contaminated wastewater is expectable.     

Removal of chromate from wastewater using amine-based-surfactant-modified clinoptilolite

This study presents the results of chromate adsorption upon organically modified clinoptilolite obtained by the treatment of Bigadic clinoptilolite with surfactants in primary amine structure, namely 1-dodecylamine, 1-hexadecylamine and oleylamine. Natural and organo-clinoptilolites were characterized by X-ray diffraction, thermal gravimetry and Fourier transform infrared spectrometry which proved the integration of amine groups followed by the order oleylamine > 1-hexadecylamine > 1-dodecylamine. Organo-clinoptilolites were tested for their efficacy in chromate removal under base case conditions which implied 100 ppm initial concentration, pH 4.0, 10 g l^?1 adsorbent dose and at 298 K. Results showed that amine loading induced chromate removal reaching up to 90 % for oleylamine-modified clinoptilolite. Experimentation was continued to determine the effects of pH, adsorbent dosage and initial concentration on chromate adsorption. Accordingly, maximum removal of 94.0 % was attained with 14 g l^?1 of oleylamine-modified clinoptilolite, from Cr(VI) solution of 100 ppm initially at pH 3.0. Langmuir isotherm described the adsorption of chromate on oleylamine-modified clinoptilolite with 96.4 % consistency. Maximum theoretical uptake capacity was calculated as 6.72 mg g^?1. Kinetic data were consistent with pseudo-second-order model with the controlling steps being film and pore diffusions.     

Fast,green and effective chromium bio-speciation using <Emphasis Type="Italic">Sepia pharaonis</Emphasis> endoskeleton nano-powder

The development of a fast, effective, simple and low-cost procedure for chromium speciation is an analytical challenge. In this work, a new and simple method for speciation and determination of chromium species in different matrices was developed. Sepia pharaonis endoskeleton nano-powder was used as an adsorbent for the dispersive micro-solid-phase extraction. Finally, the desorbed chromium was determined using a graphite furnace atomic absorption spectrometer. The experimental results showed that Cr(III) could be quantitatively extracted by the adsorbent, while Cr(VI) adsorption was negligible. Concentrated H₂SO₄ and ethanol reduced Cr(VI)–Cr(III), and total chromium content was assessed as Cr(III). Then, the Cr(VI) concentration in the sample was calculated as the difference. The optimum conditions were obtained in terms of pH, adsorbent amount, contact time, and type, concentration and volume of eluent. Under the optimum conditions that involved the speciation of chromium ions from 25 mL of the water samples at pH 7.0 using 0.025 g of the adsorbent with contact time of 5 min, the method was validated in terms of linearity, precision and accuracy. The calibration curve was linear over the concentration range of 0.01–25.00 μg L^?1 for Cr(III). The obtained limit of detection for the proposed method was 0.003 µg L^?1. The maximum adsorption capacity of the adsorbent was found to be 995.57 mg g^?1. The proposed method was validated by the speciation of Cr(III) and Cr(VI) in different real water and wastewater samples with satisfactory results.     

Isolation and characterization of metal-resistant bacterial strain from wastewater and evaluation of its capacity in metal-ions removal using living and dry bacterial cells

A novel strain of the genus Micrococcus isolated from wastewater was studied for resistance to seven heavy metals and forty antibiotics. Its capacity to accumulate metal ions was also realized at different pH. The strain exhibited high minimal inhibitory concentration values for metal ions tested and resist to 15 antibiotics. The living cells of the bacterial strain show a largest uptake capacity at pH 6–8.5 for copper, nickel, and zinc with values ranging from 51.45 to 83.90 %, 52.59 to 78.81 %, and 59.55 to 78.90 %, respectively. It was also able to absorbed 59.81–80.08 % of chromium and 58.09–79.41 % of cobalt at pH 7.3–8.5. The maximum lead uptake was obtained at pH 5.5–8.5 with an amount of 55.28–91.06 %. The significant absorption of cadmium was shown at pH 6.5 with 38 %. In 25 µg mL-1 zinc, chromium, and nickel solutions, dead cells of the isolate were able to biosorbed 20.46, 22.5, and 23.98 µg mL^?1, respectively, after 30 min of contact. In other solutions with higher concentrations 50 and 100 µg mL^?1, the amount of each metal immobilized was, respectively, as follows: 38.02 and 90.21 µg mL^?1 for zinc, 39.78 and 89.23 µg mL^?1 for chromium, and 47.19 and 86.83 µg mL^?1 for nickel. Due to its high-metal accumulation capacity in aerobic conditions, these Gram-positive bacteria may be potentially applicable in situ bioremediation of heavy metals contaminating aqueous systems.     

High-resolution profiles of iron, manganese, cobalt, cadmium, copper and zinc in the pore water of estuarine sediment

The remobilization of iron, manganese, cobalt, cadmium, copper and zinc in the pore water of estuarine sediment cores at Yingkou was assessed using diffusive equilibrium in thin films and diffusive gradients in thin films techniques. A relatively anoxic system (+33.7 to ?224.1 mV) in the sediment cores might cause the reductive release of iron, manganese and cobalt into pore water from the estuarine sediment. High-average concentrations of iron (47.85 μg ml^?1) and manganese (3.81 μg ml^?1) were observed using diffusive equilibrium in thin films on the sediment core, but the concentration of cobalt (18.02 ng ml^?1) was relatively low. A strong correlation between iron and cobalt was observed based on the vertical profiles of the metals. Manganese and iron were more readily released from the solid phase to the solution. The peak cobalt, copper and zinc concentrations were observed in the upper layer (2–4 cm) measured using diffusive gradients in thin films. However, the peak iron, manganese and cobalt concentrations were located in the deeper layer (≥7 cm). In addition, the concentration profiles measured using diffusive gradients in thin films of cobalt, copper and zinc were independent of the iron, manganese and cobalt distribution with respect to depth.     

Ameliorating nitrite inhibition in a low-temperature nitritation–anammox MBBR using bacterial intermediate nitric oxide

The long-term sustainability of an anaerobic ammonium oxidation (anammox) process in a moving bed biofilm reactor (MBBR) treating highly concentrated (mean of 740 mg NH₄ ⁺-N L^?1) wastewater was demonstrated by 1600 days of efficient operation. A high maximum total nitrogen removal rate (TNRR) of 1.5 g N m^?2 d^?1 was achieved at the low temperature of 20 °C. For nitrogen removal recovery in cases of nitrite inhibition, anammox intermediate nitric oxide (NO) was tested in batch experiments as an N-removal accelerating agent. The effect of the addition of various NO dosages (8–72 mg NO-N L^?1) was studied under inhibitory nitrite concentrations (>100 mg NO₂ ^?-N L^?1) for anammox bacteria. Optimal maintained NO concentration was 58 mg NO-N L^?1 and brought about the highest biofilm-specific anammox activity (SAA). Compared to a blank test, the minimum concentration of added NO of 40 mg NO-N L^?1 showed a statistically significant (p < 0.05) accelerating effect on SAA. No inhibition of SAA by NO was observed, although at NO concentrations exceeding 72 mg NO-N L^?1, the acceleratory effect upon SAA was decreased by 8%. Changes in the bacterial consortia involved in nitrogen conversion were determined concurrently for the different nitrogen removal rates and operational conditions. Quantities of Planctomycetales clone P4 strains, which are the closest (99% similarity) relative to Candidatus Brocadia fulgida, increased from 1 × 10³ to 1 × 10⁶ anammox gene copies per g total suspended solids during reactor operation days 568–1600, which was determined by quantitative polymerase chain reaction. During the operation of the MBBR, the abundance of ammonium-oxidizing bacteria (AOB) increased proportionally (up to 30%). The abundance of nitrite-oxidizing bacteria (NOB) did not increase (remaining below 10%) during days 232–860. AOB became predominant over NOBs owing to the inhibition of free ammonia spiking on NOBs.     

Phosphorus Budget of the Sundarban Mangrove Ecosystem: Box Model Approach

Phosphorus (P) cycling in mangroves plays an important role in productivity but the magnitude of atmospheric input in the mangrove P budget is still uncertain. This study applied a box model approach to assess P budget in the Indian Sundarban, the world’s largest mangrove ecosystem for conceptual understanding of P cycling and for better representation of transport and transformation of P within the mangrove ecosystem. The P content in the sediment (0.19–0.67 μg g^?1) was found much below its maximum retention capacity (322 μg g^?1) and was lower than the mean marine sediment (669 μg g^?1). The C:N and C:P ratios were correlated (r ² = 0.66, P < 0.01) and the major fraction of available P was recycled within the organic structure of mangrove ecosystem, thus maintaining productivity through conservation strategies. Atmospheric input accounted for 56.7% of total P input (16.06 Gg year^?1) and 50% of total P output (14.7 Gg year^?1) was attributed to plant uptake. Budget closing or unaccounted P (1.36 Gg) was only 8.5% of the total input. Two feedback pathways, i.e., input of P from dust fallout and biochemical mineralization of organic matter, significantly affected P availability. The findings of the study suggest that atmospheric deposition is of major importance as a natural and/or anthropogenic forcing function in the Sundarban mangrove system.     

Changes in water chemistry along the newly formed High Arctic fluvial–lacustrine system of the Brattegg Valley (SW Spitsbergen,Svalbard)

Changes in water chemistry along the High Arctic fluvial–lacustrine system located in Wedel Jarlsberg Land in the SW Spitsbergen (Svalbard) were investigated during the summer season of 2010 and 2011. The newly formed river–lake system consists of three lakes connected with the Brattegg River. The first bathymetric measurements of these lakes were made by the authors in 2010. The Brattegg River catchment represents a partly glaciered Arctic water system. The studied lakes are characterized by low mineralization and temperature of water. The value of the electrolytic conductivity (EC) ranges from 30.2 to 50.5 μS cm^?1 and the temperature of surface water from 1.5 to 7.8 °C. The temperature increase takes place downstream starting from Upper Lake to the outflow from Myrktjørna Lake. The waters of lakes have higher temperatures than the stream. The predominant ions are HCO₃ ^? (up to 16.5 mg L^?1), Cl^? (6.66–8.53 mg L^?1), Ca²⁺ (2.40–4.45 mg L^?1) and Na⁺ (2.65–3.36 mg L^?1). The highest values of ammonium and DOC found in the lowest Myrktjørna Lake seem to be related to the presence of aquatic organisms and also birds. From the group of 10 analyzed microelements, increased concentrations of aluminum, up to almost 500 μg L^?1, are present in the lakes’ water. Water isotopic composition ranges for δ¹⁸O and δ²H, from ?10.6 to ?10.9‰ and from ?70.8 to ?72.3‰, respectively. The vertical zonality of lake waters is manifested in a decrease in the temperature and increase in EC and chemical elements concentrations.     

Evaluation of trace element concentration (acid leachable) in sediments from River Pánuco and its adjacent lagoon areas, NE México

A set of forty-one surface sediment samples were collected in River Pánuco and its adjoining lagoon areas in NE Mexico to identify the enrichment pattern of trace elements. The samples were analyzed for sediment texture, carbonates, organic carbon and acid leachable trace elements (ALTEs) using autoclave method [Fe, Mn, Cr, Cu, Ni, Co, Pb, Zn, Cd, V, Be, Ba, Sr, As]. Geochemical results of Fe, Cr, Ni, Co, V and Sr in zone 1 indicate that erosion in the upland region (Sierra Madre Oriental Mountains) is very high. The above feature is supported by the supremacy of finer sediments (82.12 %), carbonates (44.67 %) and organic carbon (10.74 %), which are brought down from the drainage basin. The overall average concentration of ALTEs Mn (607 μg g^?1), Cu (28.29 μg g^?1), Ni (16.56 μg g^?1), Pb (46.11 μg g^?1), Cd (1.81 μg g^?1) and Zn (92.18 μg g^?1) indicates higher values than the lowest effect level (LEL) and effects range low (ERL) of environmental indicators. The results suggest that they are due to the increase in oil refineries, metal based industries, shipping activities and the effluent input which could enter the biological cycle and might create human health problems.     

Evaluation of effective nutritional parameters for <Emphasis Type="Italic">Scenedesmus</Emphasis> sp. microalgae culturing in a photobioreactor for biodiesel production

Recently, microalgae are considered as lipid sources for biodiesel production. A photobioreactor was designed and fabricated for Scenedesmus sp. microalgae cultivation. The effect of several nitrogen sources, light intensity, iron ions, silicon, magnesium sulfate and ethanol concentrations on Scenedesmus sp. microalgae growth were investigated. For incubation period of 8 days, sodium nitrate and ammonium carbonate were the best nitrogen sources with biomass concentrations of 2.373 and 2.254 g L^?1, respectively. Microalgae growth was reduced using nitrogen concentrations above 0.7 g L^?1. In the first 10 days of incubation, maximum cell dry weight (0.7 g L^?1) was obtained with light intensity of 10,000 lx, whiles after that, the results were desired (1 g L^?1) using interior lighting at 7500 lx. Magnesium sulfate had a positive effect on cell growth. The biomass concentration of 1.65 g L^?1 was obtained using 0.06 g L^?1 magnesium sulfate. Maximum obtained biomass with silicon (0.7 Mm), ethanol (1.8 mL L^?1) and ferric ammonium citrate (0.02 g L^?1) was 1.7 and 1.3 and 2.16 g L^?1, respectively. Logistic model was found to be a suitable model for cell growth forecast. Fatty acid analysis showed that composition of the most dominant synthesized fatty acids, palmitic and oleic acids, was 21.16 and 33.58%, respectively. Oil produced by Scenedesmus sp. microalgae composed of 49.08% saturated and 43.53% unsaturated fatty acids has a suitable composition for a desired biodiesel.     

Induced degradation of crude oil mediated by microbial augmentation and bulking agents

Different bacterial and fungal strains, isolated from petroleum hydrocarbon-contaminated soil, were tested, in isolation as well as in combination, for their ability to degrade total petroleum hydrocarbon (TPH) in soil samples spiked with crude oil (2, 5 or 10 %, w/w) for 30 days. The selected combination of bacterial and fungal isolates, i.e., Pseudomonas stutzeri BP10 and Aspergillus niger PS9, exhibited the highest efficiency of TPH degradation (46.7 %) in soil spiked with 2 % crude oil under control condition. Further, when this combination was applied under natural condition in soil spiked with 2 % (w/w) crude oil along with inorganic fertilizers (NPK) and different bulking agents such as rice husk, sugarcane, vermicompost or coconut coir, the percent degradation of TPH was found to be maximum (82.3 %) due to the presence of inorganic fertilizers and rice husk as bulking agent. Further, results showed that the presence of NPK and bulking agents induced the activity of degradative enzymes, such as catalase (0.718 m mol H₂O₂ g^?1), laccase (0.77 µmol g^?1), dehydrogenase (37.5 µg g^?1 h^?1), catechol 1, 2 dioxygenase (276.11 µ mol g^?1) and catechol 2, 3 dioxygenase (15.15 µ mol g^?1) as compared to control (without bioaugmentation). It was inferred that the selected combination microbes along with biostimulants could accentuate the crude oil degradation as evident from the biostimulant-induced enhanced activity of degradative enzymes.     

Distribution of cadmium among multimedia in Lake Qinghai,China

Lake Qinghai in the Qinghai-Tibet plateau is the largest lake in China. This study firstly reported the geochemistry of Cd in the lake. Water samples were collected from Lake Qinghai (n = 69) and Buha River (n = 12), while sediment (n = 22) and topsoil (n = 45) samples were collected from the lake and around the lake area, respectively. In addition, pore water samples (n = 20) were separated from sediment samples. Water samples were analyzed for pH, K, Na, Ca, Mg, Cl, S, and Cd, while sediment and topsoil samples were analyzed for K, Na, Ca, Mg, Al, Fe, Mn, S, Sc, and Cd. The average concentration of Cd was 0.014 μg L^?1 in the water of Lake Qinghai and 0.007 μg L^?1 in the water of Buha River. However, the average concentration of Cd was 0.320 μg L^?1 in the sediment pore water, much higher than that in the lake water and river water. Cadmium concentration in the lake water might be mainly controlled by salinity, while it in the pore water might be mainly controlled by carbonate minerals. Cadmium concentration in the river water might be controlled by alkalinity and pH. The average concentration of Cd in the sediment was 0.284 mg kg^?1. The enrichment of Cd in the lake sediment was significantly higher than that in the topsoil around the lake. Anthropogenic atmospheric deposition of Cd did not led to the increase in dissolved Cd level in the lake water, but led to its enrichment in the lake sediment.     

The occurrence of cyanobacteria and microcystins in the Hoan Kiem Lake and the Nui Coc reservoir (North Vietnam)

The occurrence of increasing blooms of toxic cyanobacteria in freshwaters has received much attention due to the ability of many cyanobacteria to produce potent cyanotoxins. In this paper, the occurrence of dominant cyanobacteria and the concentration of microcystins (MCs) analysis were investigated monthly from July 2008 to April 2009 in the Hoan Kiem Lake and from February to April 2009 in the Nui Coc reservoir. Concentrations of intracellular MCs from water, bloom samples, and isolated strains were quantified by using high performance liquid chromatography (HPLC). During the study period, the microscopic examination of the phytoplankton samples showed the dominance of the genus Microcystis in the water environment of the Hoan Kiem Lake and the Nui Coc reservoir. The toxin analysis by HPLC demonstrated the presence of two MC variants: MC-LR and MC-RR in water samples. Total concentrations of the toxins in filtered samples from surface water ranged from non-detected to 0.91 μg L^?1 at Nui Coc reservoir and they ranged from 2.1 to 46.0 μg L^?1 at Hoan Kiem Lake. The results of the HPLC analysis confirmed the production of MCs in bloom samples (ranged from 115.9 to 184.6 μg L^?1 in the Hoan Kiem Lake and from 726.5 to 1116 μg L^?1 in the Nui Coc reservoir) and isolated strains of Anabaena sp. and Microcystis with the concentration of MC ranging from 152 to 396.2 μg g^?1 dry mass, respectively.     

Metal distributions in seawater,sediment and marine benthic macroalgae from the South Australian coastline

Algal species which are ubiquitous along the coastlines of many countries reflect the environmental conditions of the coastal seawater and may serve as useful biomonitors of anthropogenic pollution. Heavy metal concentrations of ten elements (As, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb and Zn) of potential environmental concern were determined in seawater, sediments and twelve species of benthic marine macroalgae from four locations (Glenelg, Port Adelaide, Port Broughton and Port Pirie) along the South Australian coastline. The four sites chosen represented varying degrees of metal contamination, where the capacity for benthic macroalgae to accumulate heavy metals from the environment was evaluated. Spatial differences in heavy metal concentration in both seawaters and sediments were observed at all sites with the highest concentrations of heavy metals including Cd (125 μg g^?1), Pb (2,425 μg g^?1) and Zn (7,974 μg g^?1) found in the finer sediment fractions (<250 μm) of Port Pirie. While all algal species studied (Acrosorium polyneurum, Anotrichium tenue, Cystophora Cephalornithos Cystophora monillifera, Cystophora monilliformis, Dictyopteris australis, Gelidium micropterum, Gracilaria, Hormophysa Cuneiformis, Sargassum cinctum, Scaberia agardhii and Ulva lactuca) accumulated metals to varying degrees, Blindigia marginata was a good biomonitor species for a number of metals including Cd, Co, Cr, Fe, Pb and Zn, exhibiting both relatively high total metal concentrations and significant concentration factors.     

Assessment of heavy metals in sediment and in suspended particles affected by multiple anthropogenic contributions in harbours

La Goulette, Rades and Sidi Bou Said harbours are considered as the most important commercial and tourist ports in the Gulf of Tunis. They are located on the northeast coast of Tunis and receive industrial and municipal wastewaters from Tunis city. The contamination level of copper, lead, zinc, cadmium, manganese, iron, total nitrogen and total organic carbon in the surface sediments was assessed on the basis of the enrichment index factors and corresponding to sediment quality guidelines. The results revealed moderate to highly elevated concentrations near to the sites of intense industrial, shipping and/or commercial activities suggesting a direct influence of these sources. In winter and summer, concentrations varied for cadmium, 0.28–1.40 mg kg^?1; lead, 18–217 mg kg^?1; zinc, 87–459 mg kg^?1; copper, 8–121 mg kg^?1; manganese, 208–254 mg kg^?1; and for iron, 24–40 g kg^?1. Furthermore, in summer the concentration of the total organic carbon and the total nitrogen contents range between 4.3–6.5 % and 0.06–0.49 % with an average value of 5.9 and 0.15 %, respectively. Whereas, in winter, total organic carbon and the total nitrogen concentrations varied between 2.3–9.6 % and 0.03–0.22 % with an average value of 6.1 and 0.14 %, respectively. The levels of lead, copper, zinc and iron in suspended particulate matter content range between 3.1–27.5 mg kg^?1; 0.4–11.7 mg kg^?1; 1–1.5 mg kg^?1; 1.2–1.7 g kg^?1, respectively. This study revealed that heavy metals pollution is mainly localized in the commercial (Rades) and fishing (La Goulette) harbours and not in the yachting (Sidi Bou Said) harbour.