由声测井资料计算反射系数序列中多分辨率逼近的选择

介绍了由声测井资料计算反射系数序列中的多分辨率逼近理论,详细分析了由高分辨率的声测井资料计算低分辨率的反射系数序列的地质要求,进而在理论上讨论了此类问题中多分辨逼近的选择.并比较了由Haar系与由三次样条函数构造的多分辨率逼近这两种典型的多分辨率逼近.最后利用理论模型及实际资料算例验证了选择恰当的多分辨率逼近在解决这类问题中的有效性.     

基于频率搬移的地震资料约束测井资料外推

于地震资料本身频带有限的特性,导致在利用地震资料作为约束条件进行测井资料外推时存在奇异性. 文中利用通信中常用的频率搬移技术,将频带有限的地震资料转化成一种频带拓宽的伪超分辨率资料来控制测井资料的外推,从而解决地震资料约束下的测井资料外推技术中的奇异性问题. 并利用同相轴自动追踪和时频分析技术,解决子波时变的问题,实现沿地层自适应地外推测井资料. 对实际资料的测井速度和反射系数外推结果表明, 此法具有较好的应用前景.     

频率-波数域递推计算海底多分量地震记录中的反射系数

在频率-波数域中采用解析法,解出多层条件下海底实测的多分量地震数据分解成上行和下行P波和S波的算法,导出海底各层地震反射系数随入射角变化(简称RVA)的递推计算公式,为海底多波多分量AVO弹性参数的反演及流体因子预测提供基础数据.合成数据的计算结果表明,本文给出的算法能较可靠地从海底多波多分量记录中提取RVA信息.     

基于最小二乘逆时偏移的场声反射成像测井模拟?

近年来,声反射成像测井技术（ARILT）在井旁裂缝、孔洞性储层评价中成为研究热点。常规ARILT的探测深度一般在20m以内,且对复杂构造边界刻画能力不足。本文基于测井观测系统及采集参数,将最小二乘逆时偏移（LSRTM）地震成像技术引入ARILT中,以提高井旁区域有效成像范围和成像精度。本文在实现偏移算法及处理流程基础上,将算法用于典型模型和实际资料,重点分析不同频率、深度和偏移方法成像效果的差异。成像结果对比发现:①偏移算法影响ARILT成像精度,LSRTM具有较高分辨率,并能揭示构造体横向变化特征;②激发源频率也影响成像分辨率,提高频率会改善分辨率,但会降低探测深度;③在给定的测井观测参数下,LSRTM能有效探测23m范围内的井旁构造。      

联合高分辨率地震和精细测井资料的剩余油气分析

寻找和开发剩余油气藏是提高采收率的关键.以往主要是通过测井、试井资料建立中高层渗透砂岩油藏的井间剩余油分布模型,并采用数学分析方法建立井间剩余油的预测模型.本文介绍了基于高分辨率地震和精细测井分析建立剩余油模型并结合数模分析的剩余油分析技术.利用该技术对辽河油田某断块进行了实际剩余油气分析,在开发方案设计和提高采收率方面取得了明显的效果.     

频率-波数域递推计算海底多分量地震记录中的反射系数

在频率-波数域中采用解析法,解出多层条件下海底实测的多分量地震数据分解成上行和下行P波和S波的算法,导出海底各层地震反射系数随入射角变化(简称RVA)的递推计算公式,为海底多波多分量AVO弹性参数的反演及流体因子预测提供基础数据.合成数据的计算结果表明,本文给出的算法能较可靠地从海底多波多分量记录中提取RVA信息.     

用对称映射ARMA模型的零极点研究子波相位对反射系数序列反演的影响

为研究地震子波相位对反射系数序列反演的影响,在自回归滑动平均(ARMA)模型描述子波的基础上,提出采用z域对称映射ARMA模型零极点的方法构造了一系列相同振幅谱、不同相位谱的地震子波,并结合谱除法对人工合成地震记录进行反射系数序列反演.理论分析表明,子波相位估计不准时反射系数序列反演结果中残留一个纯相位滤波器,该纯相位滤波器的相位谱为真实子波和构造子波的相位谱之差.采用丰度和变分作为评价方法,在反演结果中确定出真实的或准确的反射系数序列.仿真实验和实际数据处理结果也验证了子波相位对反射系数序列反演的影响规律和评价方法的有效性,为进一步提高反射系数序列反演结果精度指明了研究方向.     

用形变资料反演1976年唐山地震序列的破裂分布

1976年唐山发生了7.8级地震,相继又发生了两次大余震——滦县7.1级地震和宁河6.9级地震.地震发生在观测条件比较好的地区,水准测量和三角测量测得了地震的同震位移场.本研究采用原始水准测量数据,而不是采用根据水准数据处理的地面沉降图像,和三角测量数据反演了该地震序列的破裂分布.模型构建中考虑了滦县地震和宁河地震的断层形态和大小.结果表明,唐山地震主震断层有明显的右旋走滑性质,最大走向滑动错距>6 m,位于断层南段,北段的走滑分量明显小于南段.主震总地震矩达2.58×10²⁰N·m,与地震波反演得到的地震矩的量级相当;滦县地震断层总体表现为左旋正断层,释放地震矩达4.95×10¹⁹N·m;宁河地震断层总体表现为右旋正断层,释放地震矩达3.94×10¹⁹N·m,比地震波反演的地震矩大一个量级.据此可以推测唐山地震的无震滑移主要发生在宁河地震断层的西部上,滑动性质以正断层为主.该结果对于唐山地震序列后的动力学演变过程及余震发生机理有一定参考.

     

用有限差分法计算各向异性介质中多分量感应测井的响应

感应测井电阻率是砂泥岩储层中定量评价含油气性的主要参数之一,然而由于储层电各向异性的存在,传统的感应测井仪得到的电阻率主要响应地层的水平电阻率,比地层的垂直电阻率小,由此计算的含水饱和度偏高．多分量感应测井则可以通过不同方向的发射和接收,测量多个分量,弥补上述缺陷,为储层的含油气性评价提供准确信息．本文用交错网格有限差分法导出了主轴各向异性介质中Maxwell方程的离散化关系式,计算了三维各向异性介质中多分量感应测井的电磁响应．利用三层模型的数值模拟,分析了不同磁场分量对各向异性介质的响应特性,用多层模型和倾斜各向异性地层的响应计算检验了所编制的交错网格有限差分法程序．     

CHOOSING THE AVERAGING INTERVAL WHEN CALCULATING PRIMARY REFLECTION COEFFICIENTS FROM WELL LOGS1

Most seismic data is processed using a sample interval of 4 ms two-way time (twt). The study of the statistical properties of primary reflection coefficients showed that the power spectrum of primaries can change noticeably when the logs are averaged over blocks of 0.5, 1 and 2 ms twt (block-averaging). What is a suitable block-averaging interval for producing broadband synthetics, and in particular how should the power spectrum of primaries be constructed when it is to be used to correct 4 ms sampled deconvolved seismic data for the effects of coloured primary reflectivity? In this paper we show that for a typical sonic log, a block-averaging interval of 1 ms twt should satisfy some important requirements. Firstly, it is demonstrated that if the reflection coefficients in an interval are not too large the effect of all the reflection impulses can be represented by another much sparser set at intervals of Δt twt, The coefficient amplitudes are given by the differences in the logarithmic acoustic impedances, thus justifying block-averaging. However, a condition for this to hold up to the aliasing (Nyquist) frequency is that Δt takes a maximum value of about 1 ms twt. Secondly, an event on a log should be represented in the seismic data. For this the acoustic impedance contrast must have sufficient lateral extent or continuity. By making some tentative suggestions on the relation between continuity and bed-thickness, a bed-thickness requirement of 0.15 m or more is obtained. Combining this requirement with the maximum number of beds allowable in an interval in order that multiple reflections do not contribute significantly to the reflections in the interval, again suggests a value of about 1 ms for the block-averaging interval. With this in mind an experiment was performed on three sonic logs. The logs were block-averaged at 1 ms, and primary reflection coefficients calculated. These primaries were then anti-alias filtered and resampled to get a series of primaries at 4 ms, followed by ARMA spectrum fitting. The same logs were also block-averaged at 4 ms directly and primaries computed, followed by ARMA spectrum fitting. In all three cases the first approach gave the ARM A model spectrum with greatest dynamic range, which strongly suggests that direct 4 ms block-averaging introduces significant aliased energy into low frequencies of the primaries spectrum. The conclusion is that routine computation of broadband synthetics (primaries only or primaries plus multiples) should be carried out using a block-averaging interval of 1 ms twt, followed by anti-alias filtering and thinning to the desired final sample interval. In theory it would be advantageous to go to even finer intervals-say 0.5 ms-but in practice at this level the averaging of slowness imposed by the somic logging tool appears to attenuate high-wave number fluctuations, i.e. it interferes with the‘real’data. The 1ms choice is thus a reasonable compromise which will help minimize non-trivial aliasing effects and should give better matches to the seismic data.     

唐山震区深反射剖面分析

为了进一步研究唐山地区深部地壳构造与唐山大地震孕育及发生的关系,国家地震局地球物理研究所在石油部物探局的协助下,于1985年1月在唐山震区完成了64km长的深反射剖面野外观测,获得了高分辨率的整个地壳结构的详细资料。分析结果表明,唐山震区内深度500m以上的沉积层十分破碎;结晶基底为前震旦纪地层,埋深2-7km不等,覆盖地层倾斜,且断层发育,其中陡河断裂为正断层,延深至6-7km,推断该断层为1976年唐山发震的重要构造之一。测线上大约21km深处普遍存在一反射层;莫霍面深度在31-32km左右,与该地区折射剖面得到的结果相当一致。     

高温热水孔逸出气氡观测实验研究

本文通过在漳州龙师１＃井开展的逸出气氡观测实验研究，认为逸出气氡作为新的地震前兆观测项目是可行的，可以进行平行样观测，同时可得到Ｒｎ气／Ｒｎ水比值，作为研究地下流体前兆的一个新的参数。并对应用电离法测量逸出气氡的连续自记观测技术进行了预研究试验。     

山东聊古一井水化学组分地震异常的场源兆特征及其机制讨论

从山东聊古一井构造地质和水文地质条件的分析入手，以实际观测的水化学组分地震前兆异常变化实例为基础，讨论了该井水化学组分震前异常变化的场源兆特征．利用断层位错理论和岩石力学实验获得的认识探讨了聊古一井水化学组分变化场源兆异常形成的物理力学机制及预报意义．所获成果丰富了对场源兆地震前兆的认识，同时对地震预测预报也有一定的意义．     

Mini-Sosie浅层高分辨反射波技术在西安市地裂缝研究中应用

一、前言 西安市地表出现八条地裂缝带,总体走向N70°-80°E,间距2-2.5 km,长度约3-4 km,最长约8 km,近似于平行等间距展布在城区和近郊区的150 km²范围内,将西安市切割成规则条带,由于不断活动,二十多年来造成的破坏,相当于Ⅳ-Ⅶ度的地震。 1986-1987年,我们用Mini-Sosie高分辨反射波技术,在辛家庙（F1）、小寨（F7）     

DATA COMPARATIVE ANALYSIS BETWEEN SFM DATA AND DGPS DATA: A CASE STUDY FROM FAULT SCARP IN THE EAST BANK OF HONGSHUIBA RIVER,NORTHERN MARGIN OF THE QILIAN SHAN

With the development of the techniques acquiring high-resolution digital terrain data,the digital terrain data acquisition technology has been widespread applied to the geoscience research.A revolutionary,low-cost and simply operative SfM (Structure from Motion) technology will make obtain high-resolution DEM data more convenient for researches on active tectonics.This paper summarizes the basic principles and workflows of SfM technology and processes and selects the Hongshuiba River area along the northern margin of the Qilian Shan to conduct data collection.We use a series of digital pictures to produce a texture with geographic information,in which data resolution is 6.73cm/pix and average density of point cloud is 220.667 point/m².The coverage area is 0.286km².Further,in order to compare the accuracy between SfM data and differential GPS (DGPS) data in details,SfM data are vertically shifted and tilt-corrected.After optimizing corrections of SfM data,the absolute value of elevation difference between two data substantially concentrates around 20cm,roughly equivalent to 2-folds of data error only after the elevation error correction.Elevation difference between two data is 10~15cm in 90% confidence interval.The maximum error is about 30cm,but accounts for less than 10%.Along the direction of fault trace,the height of fault scarp extracted from SfM data shows that vertical displacement of the latest tectonic activity in the east bank of Hongshuiba River is about 1m,and some minimum scarps height may be 0.3m.The results show SfM technology with high vertical accuracy can be able to replace differential GPS in high-precision topographic survey.After correcting of SfM data,elevation difference still exists,which may be associated with methods of generating DEM and SfM data accuracy,which in turn is controlled by the number and distribution of Ground Control Points (GCPs),photos density and camera shooting height,but also related to surface features,Fodongmiao-Hongyazi Fault