Relief-rejuvenation and topographic length scales in a fluvial drainage basin, Napf area, Central Switzerland

This paper explores how, and to what extent, a phase of relief-rejuvenation modifies the mode of surface erosion in an approximately 63 km² drainage basin located at the northern border of the Swiss Alps (Luzern area). In the study area, the retreat of the Alpine glaciers at the end of the Last Glacial Maximum (LGM) caused base level to lower by approximately 80 m. The fluvial system adapted to the lowered base level by headward erosion. This is indicated by knickzones in the longitudinal stream profiles and by the continuous upstream narrowing of the width of the valley floor towards these knickzones. In the headwaters above these knickzones, processes are still to a significant extent controlled by the higher base level of the LGM. There, frequent exposure of bedrock in channels and especially on hillslopes implies that sediment flux is to a large extent limited by weathering rates. In the knickzones, however, exposure of bedrock in channels implies that sediment flux is supply-limited, and that erosion rates are controlled by stream power.The morphometric analysis reveals the existence of length scales in the topography that result from distinct geomorphic processes. Along the tributaries where the upstream sizes of the drainage basins exceed 100,000–200,000 m², the mode of sediment transport and erosion changes from predominantly hillslope processes (i.e., landsliding, creep of regolith, rock avalanches and to some extent debris flows) to processes in channels (fluvial processes and debris flows). This length scale reflects the minimum size of the contributing area for channelized processes to take over in the geomorphic development (i.e., threshold size of drainage basin). This threshold size depends on the ratio between production rates of sediment on hillslopes, and export rates of sediment by processes in channels. Consequently, in the headwaters, erosion rates and sediment flux, and hence landscape evolution rates, are to a large extent limited by weathering processes. In contrast, in the lower portion of the drainage basin that adjusts to the lowered base-level, rates of channelized erosion and relief formation are controlled mainly by stream power. Hence, this paper shows that base-level lowering, headward erosion and establishment of knickzones separate drainage basins in two segments with different controls on rates of surface erosion, sediment flux and relief formation.     

Uplift, exhumation and precipitation: tectonic and climatic control of Late Cenozoic landscape evolution in the northern Sierras Pampeanas, Argentina

Deciphering the evolution of mountain belts requires information on the temporal history of both topographic growth and erosion. The exhumation rate of a mountain range undergoing shortening is related to the erodability of the uplifting range as well as the efficiency of erosion, which partly depends on the available precipitation. Young, rapidly deposited sediments have low thermal conductivity and are readily eroded, in contrast to underlying resistant basement rocks that have a higher thermal conductivity. Apatite fission‐track thermochronology can quantify cooling; thermal models constrain the relationship between this cooling and exhumation. By utilizing geological relations for a datum, we can examine the evolution of rock uplift, surface uplift and exhumation. In the northern Sierras Pampeanas of Argentina, a young sedimentary basin that overlay resistant crystalline basement prior to rapid exhumation provides an ideal setting to examine the effect of contrasting thermal and erosional regimes. There, tectonically active reverse‐fault‐bounded blocks partly preserve a basement peneplain at elevations in excess of 4500 m. Prior to exhumation, the two study areas were covered by 1000 and 1600 m of recently deposited sediments; this sequence begins with shallow marine deposits immediately overlying the regional erosion surface. Apatite fission‐track data were obtained from vertical transects in the Calchaquíes and Aconquija ranges. At Cumbres Calchaquíes, erosion leading to the development of the peneplain commenced in the Cretaceous, probably as a result of rift‐shoulder uplift. In contrast, Sierra Aconquija cooled rapidly between 5.5 and 4.5 Myr. At the onset of this rapid exhumation, the sediment was quickly removed, causing fast cooling, but relatively slow rates of surface uplift. Syntectonic conglomerates were produced when faulting exposed resistant bedrock; this change in rock erodability led to enhanced surface uplift rates, but decreased exhumation rates. The creation of an orographic barrier after the range had attained sufficient elevation further decreased exhumation rates and increased surface uplift rates. Differences in the magnitude of exhumation at the two transects are related to both differences in the thickness of the sedimentary basin prior to exhumation and differences in the effective precipitation due to an orographic barrier in the foreland and hence differences in the magnitude of headward erosion.     

Modelling of drainage dynamics influence on sediment routing system in a fold‐and‐thrust belt

Drainage networks link erosional landscapes and sedimentary basins in a source‐to‐sink system, controlling the spatial and temporal distribution of sediment flux at the outlets. Variations of accumulation rates in a sedimentary basin have been classically interpreted as changes in erosion rates driven by tectonics and/or climate. We studied the interactions between deformation, rainfall rate and the intrinsic dynamics of drainage basins in an experimental fold‐and‐thrust belt subjected to erosion and sedimentation under constant rainfall and shortening rates. The emergence of thrust sheets at the front of a prism may divert antecedent transverse channels (perpendicular to the structural grain) leading to the formation of longitudinal reaches, later uplifted and incorporated in the prism by the ongoing deformation. In the experiments, transverse incisions appear in the external slopes of the emerging thrust sheets. Headward erosion in these transverse channels results in divide migration and capture of the uplifted longitudinal channels located in the inner parts of the prism, leading to drainage network reorganization and modification of the sediment routing system. We show that the rate of drainage reorganization increases with the rainfall rate. It also increases in a nonlinear way with the rate of uplift. We explain this behaviour by an exponent > 1 on the slope variable in the framework of the stream power erosion model. Our results confirm the view that early longitudinal‐dominated networks are progressively replaced by transverse‐dominated rivers during mountain building. We show that drainage network dynamics modulate the distribution of sedimentary fluxes at the outlets of experimental wedges. We propose that under constant shortening and rainfall rates the drainage network reorganization can also modulate the composition and the spatial distribution of clastic fluxes in foreland basins.     

THE ROLE OF PERIMETER SHAPE IN ESTIMATING ANNUAL RUNOFF FROM SMALL SIERRA NEVADA BASINS

Perimeter shape of drainage basins is evaluated as a control of annual runoff depth from small Sierra Nevada basins underlain by granitic rocks. In contrast to three perimeter shape ratios, none of which contributes a statistical explanation of annual runoff depth, three terms of a Fourier expansion of the basin perimeter substantially improve the estimating model. When added to annual precipitation, the first, third, and seventh Fourier amplitudes increase statistical explanation by 15 percent and prediction accuracy by 10 percent. These improvements are much greater than corresponding gains atributable to other morphological variables. [Key words: basin runoff, basin shape, Sierra Nevada.]     

Drainage integration and sediment dispersal in active continental rifts: A numerical modelling study of the central Italian Apennines

Progressive integration of drainage networks during active crustal extension is observed in continental areas around the globe. This phenomenon is often explained in terms of headward erosion, controlled by the distance to an external base‐level (e.g. the coast). However, conclusive field evidence for the mechanism(s) driving integration is commonly absent as drainage integration events are generally followed by strong erosion. Based on a numerical modelling study of the actively extending central Italian Apennines, we show that overspill mechanisms (basin overfilling and lake overspill) are more likely mechanisms for driving drainage integration in extensional settings and that the balance between sediment supply vs. accommodation creation in fault‐bounded basins is of key importance. In this area drainage integration is evidenced by lake disappearance since the early Pleistocene and the transition from internal (endorheic) to external drainage, i.e. connected to the coast. Using field observations from the central Apennines, we constrain normal faulting and regional surface uplift within the surface process model CASCADE (Braun & Sambridge, 1997, Basin Research, 9, 27) and demonstrate the phenomenon of drainage integration, showing how it leads to the gradual disappearance of lakes and the transition to an interconnected fluvial transport system over time. Our model results show that, in the central Apennines, the relief generated through both regional uplift and fault‐block uplift produces sufficient sediment to fill the extensional basins, enabling overspill and individual basins to eventually become fluvially connected. We discuss field observations that support our findings and throw new light upon previously published interpretations of landscape evolution in this area. We also evaluate the implications of drainage integration for topographic development, regional sediment dispersal and offshore sediment supply. Finally, we discuss the applicability of our results to other continental rifts (including those where regional uplift is absent) and the importance of drainage integration for transient landscape evolution.     

River spacing and drainage network growth in widening mountain ranges

Drainage networks in linear mountain ranges always display a particular geometrical organisation whereby the spacing between the major drainage basins is on average equal to half the mountain width (distance from the mountain front to the main drainage divide), independent of climate and tectonics. This relationship is valid for mountains having different widths and is thus usually thought to be maintained by drainage reorganisation during mountain belt widening. However, such large‐scale systematic drainage reorganisation has never been evidenced. In this paper, we suggest an alternative explanation, namely that the observed drainage basin relationships are an inherent property of dendritic river networks and that these relationships are established on the undissected, lowland margins outside mountain ranges and are progressively incorporated and quenched into uplifted topography during range widening. Thus, we suggest that the large‐scale geometry of drainage networks in mountain ranges is mainly antecedent to erosion. We propose a model in which the large‐scale drainage geometry is controlled mainly by the geometrical properties of the undissected surfaces (in particular, the ratio of the regional slope to the local slope related to roughness) over which rivers are flowing before uplift, and is therefore independent of climate and tectonics.     

Late orogenic intramontane basin development: the Granada basin, Betics (southern Spain)

The quantitative study of subsidence in the Granada basin, using decompaction and backstripping techniques, and contemporaneous relief development in the surrounding areas, especially in the Sierra Nevada, provides a good case example of the development of an intramontane basin. In the Granada basin, according to the interpretation of the seismic profiles and results of the backstripping analysis, subsidence and sedimentation rates were at a maximum in the late Tortonian and decreased progressively; meanwhile, the neighbouring areas were uplifted forming important relief. Chronostratigraphical revisions of the marine sediments show that the marine incursion that deposited sediments in the Granada basin lasted only 1.3 Ma, between 8.5 and 7.2 Ma. The gradual retreat of the sea in the Granada basin is not attributable to global eustatic fluctuations, but rather to uplift in the Sierra Nevada and its adjacent areas. From latest Tortonian to early Messinian times, the region became continental and the Granada basin acquired its present physiography and was differentiated as such. From the late Tortonian onwards, NNW–SSE compression combined with ENE–WSW extension affected the cordillera. In the Granada basin, extension controlled fault movements. There are two well-defined fault sets: the first trends 70°N–90°E, with low angle faults (less than 30°) dipping towards the north and south, defining the subsiding areas which have approximately E–W direction; whereas the second set has a NW–SE direction, and cuts and displaces the previous ones, defining the main subsiding areas in the eastern part of the basin. The reinterpretation of seismic profiles reveals that the subsiding axes within the Granada basin persisted from the Tortonian to the present because of continued displacements of the main faults.     

A model for post‐orogenic development of a mountain range and its foreland

Decaying mountain ranges often show a surprisingly dynamic pattern of landscape evolution. Although one might expect a simple, monotonic decline in relief over time, evidence from several inactive mountain ranges shows alternating sequences of deposition and erosion in the associated basins, suggesting variations in relief and exhumation rate in the ranges themselves. Examples include the Southern Rocky Mountains, the Pyrenees, the European Alps and the Atlas Mountains. In this paper, we explore the possible origins of post‐orogenic landscape dynamics using a simple mathematical model of a mountain range and an adjacent foreland basin. The analysis highlights the importance of mass balance. In particular, a switch from basin exhumation to renewed sedimentation requires either an increase in sediment influx from the range or a decrease in sediment outflux beyond the basin margin. Although it is widely understood that post‐orogenic changes in erosion and sediment flux can have multiple causes (including climate change, regional tectonic uplift or tilting, or exhumation of variable lithologies), an important implication of our analysis is that the impact of such changes must differ in sign or magnitude between the range and the basin to be recorded. This requirement places an important constraint on viable explanations for alternating sequences of deposition and erosion in a decaying mountain‐basin pair.     

中国主要流域盆地风化剥蚀率的控制因素

利用中国40余条主要河流及其支流的沉积物和溶解质载荷分别去表征流域盆地的物理剥蚀率和化学风化率。研究发现,中国流域盆地的总剥蚀率明显高于世界平均值,且具有南北低中间高的地理分布特点,黄河中游的皇甫川机械和总剥蚀率是世界上已知的最高值。根据流域盆地的机械剥蚀率、化学风化率和总剥蚀率及其影响因子之间的相关分析,得出中国流域盆地中的机械剥蚀率在总剥蚀率中占主导地位,机械剥蚀率和总剥蚀率主要由流域的干旱指数和相对高差来控制,不同流域之间总剥蚀率72%的差异是由于这两个参数所造成的。而化学风化率在总剥蚀率中总是处于次要地位,它主要受到流域年均降水量和气温的影响(39%),且不受机械剥蚀率的控制。流域盆地自身属性、径流量、最高海拔和森林覆盖率对流域岩石的风化剥蚀率影响不大。构造活动提高了流域的机械剥蚀率和化学风化率,且对机械剥蚀率的影响更强烈。与世界流域盆地相比,中国流域盆地受到流域干旱指数的影响更为显著。     

祁连山东段庄浪河流域地貌特征及其构造指示意义

晚新生代以来,青藏高原北东向扩展,致使祁连山地区遭受了强烈的构造隆升,造就了祁连山地区复杂的构造格局和急剧变化的构造地貌,其典型水系流域地貌特征揭示了该地区的新构造活动和地貌演化过程。庄浪河流域位于祁连山东段,作为青藏高原北东向扩展的前缘地区,庄浪河流域的地貌参数对构造活动非常敏感,提取庄浪河流域的地貌信息,有助于揭示祁连山东段庄浪河流域地貌对构造活动的响应,及系统探讨该区地貌发育特征及其所蕴含的构造意义。庄浪河流域内及边缘发育有庄浪河断裂、天祝盆地南缘断裂、疙瘩沟隐伏断裂以及金强河-毛毛山-老虎山断裂。晚新生代以来,这些断裂仍在活动,并且控制着流域内的构造变形、山体隆升和河流水系地貌发育。本研究采用ALOS DEM 12.5 m数据,基于ArcGIS空间分析技术,通过高程条带剖面、河流坡降指标体系（K,SL,SL/K）和Hack剖面、面积-高程积分值（HI）和积分曲线（HC）等方法,对庄浪河流域地貌特征进行了初步分析。结果表明,庄浪河地区地形起伏由北西向南东递减,构造活动存在东西分异的规律;庄浪河流域内部K值、SL、SL/K、HI值西侧高于东侧,Hack剖面西侧相比东侧上凸更明显;H...     

Small valley glaciers and the effectiveness of the glacial buzzsaw in the northern Basin and Range, USA

The glacial buzzsaw hypothesis suggests that efficient erosion limits topographic elevations in extensively glaciated orogens. Studies to date have largely focussed on regions where large glaciers (tens of kilometres long) have been active. In light of recent studies emphasising the importance of lateral glacial erosion in lowering peaks and ridgelines, we examine the effectiveness of small glaciers in limiting topography under both relatively slow and rapid rock uplift conditions. Four ranges in the northern Basin and Range, Idaho, Montana, and Wyoming, USA, were chosen for this analysis. Estimates of maximum Pleistocene slip rates along normal faults bounding the Beaverhead–Bitterroot Mountains (~ 0.14 mm y^− 1), Lemhi Range (~ 0.3 mm y^− 1) and Lost River Range (~ 0.3 mm y^− 1) are an order of magnitude lower than those on the Teton Fault (~ 2 mm y^− 1). We compare the distribution of glacial erosion (estimated from cirque floor elevations and last glacial maximum (LGM) equilibrium line altitude (ELA) reconstructions) and fault slip rate with three metrics of topography in each range: the along-strike maximum elevation swath profile, hypsometry, and slope-elevation profiles. In the slowly uplifting Beaverhead–Bitterroot Mountains, and Lemhi and Lost River Ranges, trends in maximum elevation parallel ELAs, independent of variations in fault slip rate. Maximum elevations are offset ~ 500 m from LGM ELAs in the Lost River Range, Lemhi Range, and northern Beaverhead–Bitterroot Mountains, and by ~ 350 m in the southern Beaverhead–Bitterroot Mountains, where glacial extents were less. The offset between maximum topography and mean Quaternary ELAs, inferred from cirque floor elevations, is ~ 350 m in the Lost River and Lemhi Ranges, and 200–250 m in the Beaverhead–Bitterroot Mountains. Additionally, slope-elevation profiles are flattened and hypsometry profiles show a peak in surface areas close to the ELA in the Lemhi Range and Beaverhead–Bitterroot Mountains, suggesting that small glaciers efficiently limit topography. The situation in the Lost River Range is less clear as a glacial signature is not apparent in either slope-elevation profiles or the hypsometry. In the rapidly uplifting Teton Range, the distribution of ELAs appears superficially to correspond to maximum topography, hypsometry, and slope-elevations profiles, with regression lines on maximum elevations offset by ~ 700 and ~ 350 m from the LGM and mean Quaternary ELA respectively. However, Grand Teton and Mt. Moran represent high-elevation “Teflon Peaks” that appear impervious to glacial erosion, formed in the hard crystalline bedrock at the core of the range. Glacier size and drainage density, rock uplift rate, and bedrock lithology are all important considerations when assessing the ability of glaciers to limit mountain range topography. In the northern Basin and Range, it is only under exceptional circumstances in the Teton Range that small glaciers appear to be incapable of imposing a fully efficient glacial buzzsaw, emphasising that high peaks represent an important caveat to the glacial buzzsaw hypothesis.     

Tectonic significance of the present relief of the Betic Cordillera

Tortonian calcarenites of the Betic Cordillera were deposited in coastal or very shallow marine environments and represent an ideal marker for estimating vertical movements from the late Miocene to the Present. A map showing the heights at which these Tortonian marine rocks are situated has a clear correlation with the present relief, indicating that today's relief has been formed since the Tortonian. There is also a good correlation between present relief and the Bouguer anomaly distribution in the Betic Cordillera, as well as with crustal thickness. Likewise, the present relief is directly related to the geodynamic setting of a horizontal N–S to NNW–SSE compression and an almost perpendicular extension, along with isostatic readjustment, existing in the Betic Cordillera from the Tortonian. As a result of these regional stresses, faults and folds have produced notable vertical movements. The highest rates of uplift of the Betic Cordillera coincide with large antiforms, in particular those of the Sierra Nevada and the Sierra Filabres. Several subsiding sectors also exist (for example, the Granada Basin or the Guadalquivir Basin). The foreland Guadalquivir Basin has a complex history because the uplift in its eastern sector and subsidence in the western sector coexisted during the late Tortonian. Today the whole Betic Cordillera is characterized by differential regional uplift, even in the aforementioned subsiding sectors.     

Relative size of fluvial and glaciated valleys in central Idaho

Quantitative comparisons of the morphometry of glaciated and fluvial valleys in central Idaho were used to investigate the differences in valley relief and width in otherwise similar geologic and geomorphic settings. The local relief, width, and cross-sectional area of valleys were measured using GIS software to extract information from USGS digital elevation models. Hillslope gradients were also measured using GIS software. Power-law relationships for local valley relief, width, and cross-sectional area as a function of drainage area were developed. Local valley relief in glaciated valleys relates to drainage area with a power-law exponent similar to fluvial valleys, but glaciated valleys are deeper for a given drainage area. Local valley width in glaciated valleys is greater than in fluvial valleys, but the exponent of the power-law relationship to drainage area is similar in both valley types. Local valley cross-sectional area in glaciated valleys increases with drainage area with a power-law exponent similar to fluvial valleys, however, glacial valleys have roughly 80% greater cross-sectional area. Steep valley walls in glaciated basins increase the potential for bedrock landsliding relative to fluvial basins. Both the Olympic Mountains of Washington and valleys in central Idaho show relationships in which glaciated valleys are up to 30% deeper than fluvial valleys despite differences in lithology, tectonic setting, and climate.     

黄河中游流域地貌形态对流域产沙量的影响

在黄河中游地区 ,选择了 5 0多个面积约 5 0 0～ 2 5 0 0平方公里的水文测站流域 ,分别代表 6种不同自然地理类型 ,在流域沟壑密度、沟间地坡度小于 15°面积百分比等地貌形态指标量计的基础上 ,进行了流域产沙量与地貌形态指标相关分析。结果表明 ,对于不同类型流域 ,流域产沙量随流域地貌的变化遵循不同的响应规律 ,而且视流域其它下垫面环境条件的均一程度 ,其相关程度和响应速率各不相同。受地面物质、植被、地貌发育阶段等流域其它下垫面环境条件的制约 ,除沟壑密度外 ,流域产沙量与流域地貌形态的关系都没有人们以前所预期的好。     

Testing the sensitivity of geomorphic indices in areas of low-rate active folding (eastern Betic Cordillera, Spain)

Active deformation structures have an incidence in topography that can be quantified by using geomorphic indices. Most of these indices have been checked in faulted regions with high-deformation rates. The application of several geomorphic indices (hypsometric curve analysis, normalized stream-length gradient, and valley width-to-valley height ratio) to the drainage network of the southern limb of the Sierra de Las Estancias antiform (Internal Zones, eastern Betic Cordillera), where low-rate active folding has been recognized, allows us to investigate the suitability of these indices to identify active structures in such a scenario. Hypsometric curves clearly identify regions with recent uplift and young topography, but they do not provide any constraint on the location of active folds. Local valley width-to-valley height index variations have been detected just coinciding whit the position of ENE–WSW active folds. Normalized stream-length gradient index serves to locate active folds in areas of hard rock substratum, but not in those areas with soft sediments (Neogene-Quaternary sedimentary basins). This is most likely due to the fact that in the basins erosion is much more intense than in the hard rock sectors. In view of these results, we consider that geomorphic indices constitute a valuable tool for identifying sectors affected by low-rate uplift related to active folding, with the best results obtained in hard rock areas.     

全新世以来山东半岛东北部海面变化的河流地貌响应

对全新世以来山东半岛东北部沿岸的相对海面（基准面）变化,不同河流有截然不同的地貌响应方式。大沽夹河型河流的下游河谷中有分别与相对海面升降对应的溯源堆积期和溯源侵蚀期,但不同规模的河流仍有差异。黄水河型河流河谷未因基准面升降而发生侵蚀或堆积,河谷仅起了输沙通道的作用。此外,大沽夹河型河流的中下游河型在相对海面上升或下降时,还可能发生相应地网状化或曲流化。     

Universality and variability in basin outlet spacing: implications for the two-dimensional form of drainage basins

It has been observed that the distance between the outlets of transverse basins in orogens is typically half of the distance between the main divide and the range front irrespective of mountain range size or erosional controls. Although it has been suggested that this relationship is the inherent expression of Hack's law, and/or possibly a function of range widening, there are cases of notable deviations from the typical half‐width average spacing. Moreover, it has not been demonstrated that this general relationship is also true for basins in morphologically similar nonorogenic settings, or for those that do not extend to the main drainage divide. These issues are explored by investigating the relationship between basin outlet spacing and the 2‐dimensional geometric properties of drainage basins (basin length, main valley length and basin area) in order to assess whether the basin outlet spacing‐range width ratio is a universal characteristic of fluvial systems. We examined basins spanning two orders of magnitude in area along the southern flank of the Himalayas and the coastal zone of southeast Africa. We found that the spacing between basin outlets (L_os) for major transverse basins that drain the main divide (range‐scale basins) is approximately half of the basin length (L_b) for all basins, irrespective of size, in southeast Africa. In the Himalayas, while this ratio was observed for eastern Himalayan basins (a region where the maximum elevations coincided with the main drainage divide), it was only observed in basins shorter than ～30 km in the western and central Himalayas. Our analysis indicates that basin outlet spacing is consistent with Hack's law, apparently because the increase in basin width (represented by outlet spacing) with basin area occurs at a rate similar to the increase in main stream length (L_v) with basin area. It is suggested that most river systems tend towards an approximately diamond‐shaped packing arrangement, and this applies both to the nonorogenic setting of southeast Africa as well as most orogenic settings. However, in the western Himalayas shortening associated with localised rock uplift appears to have occurred at length scales smaller than most the basins examined. As a result rivers in basins longer than ～30 km have been unable to erode in a direction normal to the range front at a sufficiently high rate to sustain this form and have been forced into an alternative, and possibly unstable, packing arrangement.     

Steady, balanced rates of uplift and erosion of the Santa Monica Mountains, California

Topographic change in regions of active deformation is a function of rates of uplift and denudation. The rate of topographic development and change of an actively uplifting mountain range, the Santa Monica Mountains, southern California, was assessed using landscape attributes of the present topography, uplift rates and denudation rates. Landscape features were characterized through analysis of a digital elevation model (DEM). Uplift rates at time scales ranging from 10⁴ to 10⁶ years were constrained with geological cross-sections and published estimates. Denudation rate was determined from sediment yield data from debris basins in southern California and from the relief of rivers set into geomorphic surfaces of known age. First-order morphology of the Santa Monica Mountains is set by large-scale along-strike variations in structural geometry. Drainage spacing, drainage geometry and to a lesser extent relief are controlled by bedrock strength. Dissection of the range flanks and position of the principal drainage divide are modulated by structural asymmetry and differences in structural relief across the range. Topographic and catchment-scale relief are ≈300–900 m. Mean denudation rate derived from the sediment yield data and river incision is 0.5±0.3 mm yr^?1. Uplift rate across the south flank of the range is ≈0.5±0.4 mm yr^?1 and across the north flank is 0.24±0.12 mm yr^?1. At least 1.6–2.7 Myr is required to create either the present topographic or the catchment-scale relief based on either the mean rates of denudation or uplift. Although the landscape has had sufficient time to achieve a steady-state form, comparison of the time-scale of uplift and denudation rate variation with probable landscape response times implies the present topography does not represent the steady-state form.     

The erosion-accumulative processes within the basins of small rivers of southern East Siberia

The mean values of potential soil loss and of sediments that are removed from the gullies are calculated, and the data on the rates of erosion-accumulative processes on arable lands, in gully-dried-up river-bed systems are provided. For the Yelovka and Kuitunka rivers the basin component of the erosion-accumulative processes has been assessed qualitatively. The sequences of erosion loss to drainage basins of small rivers as well as of scouring and accumulation are determined.