Design Recommendations for Pile Subjected to Cyclic Load

Pile foundations subjected to cyclic load is an age-old problem dealt with for decades by geotechnical engineers. The ocean environment necessitates the piles supporting offshore structures to be designed against lateral cyclic loading initiated by wave action. Substantial experimental and analytical investigations have already been conducted by the author and other researchers. The quasi-static load reversal induces deterioration in the strength and stiffness of the soil-pile system introducing progressive reduction in the bearing capacity as well as settlement of the pile foundation, the degree of such degradation has been observed to be a function of the cyclic load parameters and the type of soil. Based on these observations, a design recommendation has been attempted in this paper for piles subjected to cyclic load in cohesive soil.     

考虑桩土作用独桩海洋平台横向振动特性研究

采用动Winkler弹性地基梁模型模拟桩土问动力相互作用，并考虑了流体与桩问相互作用，通过组合成层土中、水中桩单元的刚度阵，推得了独桩海洋平台连续系统横向振动的动刚度阵及在波浪力作用下平台甲板处的频率响应函数，进而求得了在确定性波浪力及随机波浪力作用下桩身任意点的位移响应。最后，通过算例研究和分析了在随机波浪力作用下成层土参数、甲板上重量及冲刷淘深等因素对平台振动响应的影响。     

Behavior of Marine Clay Subjected to Cyclic Loading with Sustained Shear Stress

Foundations of offshore structures are designed to withstand a combination of static and cyclic loads due to ocean waves. Wave action on offshore structures can cause a significant amount of cyclic horizontal and vertical forces to be transmitted to the soil through the foundation. In all these cases, these cyclic loads are considered to be superimposed over the initial sustained static stress due to the self-weight of structures. This study considers various factors that influence the development of deformation and pore water pressure in a typical cemented marine clay. These results show that the sustained static shear stress significantly influences the strength and deformation behavior of marine clay under cyclic loading. Up to a certain range of sustained static stress, there is an improvement in strength during cyclic loading and the cyclic strains are greatly reduced.     

Behavior of Marine Clay Subjected to Cyclic Loading with Sustained Shear Stress

Foundations of offshore structures are designed to withstand a combination of static and cyclic loads due to ocean waves. Wave action on offshore structures can cause a significant amount of cyclic horizontal and vertical forces to be transmitted to the soil through the foundation. In all these cases, these cyclic loads are considered to be superimposed over the initial sustained static stress due to the self-weight of structures. This study considers various factors that influence the development of deformation and pore water pressure in a typical cemented marine clay. These results show that the sustained static shear stress significantly influences the strength and deformation behavior of marine clay under cyclic loading. Up to a certain range of sustained static stress, there is an improvement in strength during cyclic loading and the cyclic strains are greatly reduced.     

Behavior of Pile Groups under Lateral Load

Based on investigation and model tests, and in combination with the research work on group effect for pile groups under lateral loads relating to the code of fixed offshore platforms, a series of studies have been performed on the behavior and failure mechanism of laterally loaded pile groups, critical pile spacing inducing group effect, lateral bearing capacity of pile groups and its main influence factors, the stress-strain relationship for single piles and pile groups and so on. Some new laws about non-uniformity of load distribution in the longitudinal direction of pile groups and load-deflection (p - y) curves for pile groups have been discovered, and an empirical formula is presented in order to remedy the defect of current calculating methods at home and abroad. These results can be used for reference in the design of pile foundation under lateral loads.     

Lateral cyclic response of an aluminum model pile in sand

Lateral cyclic load tests were performed on an aluminum model pile in dry sand. Two levels of loading were adopted to represent different service load conditions. The maximum number of loading cycles was 1,000. From the test results, it was found that the even though in the service load condition, the pile response was still affected by cyclic effects and a larger load level would produce more significant influence. In a global point of view, the lateral displacement and maximum moment increased with loading cycles, while the secant stiffness within a cycle decreased with cycles. The cyclic effect was more significant on the lateral displacement than on the moment. In a local point of view, cyclic loading would degrade the equivalent subgrade stiffness for the soil shallower than about seven times diameter. In addition, the secant subgrade stiffness within a cycle increased with loading cycles. Some experimental relationships of lateral pile response and loading cycles were built and compared with those in the literature.     

Determination of Shaft Capacity for Pile under Cyclic Axial Loading in Clay

For load-controlled and displacement-controlled test data of piles cyclically axially loaded in clay, the displacement conditions are suggested for determining the shaft capacity. According to the suggested displacement conditions, not only the results of shaft capacity from laboratory model piles are close to those from in-situ piles, but also the results of load-controlled tests are in satisfactory agreement with those of displacement-controlled tests. Moreover, based on the test data of laboratory model piles in combination with the test data published, the paper suggests the values of the normalized shaft capacity of piles under a variety of static and cyclic loading combinations.     

Influence of Frequency on the Behaviour of Plate Anchors Subjected to Cyclic Loading

This article reports the response of embedded circular plate anchors to varying frequencies of cyclic loading. The effects of time period of loading cycles and pre-loading on movement of anchors and post-cyclic monotonic pullout behavior are studied using a model circular (80 mm diameter) plate anchor, buried at embedment ratio of six in a soft saturated clay. The frequencies of loading cycles have showed considerable effect on movement of anchors. For given duration of loading, higher frequency cycles cause more movement of anchor than lower frequency cycles. Pre-loading reduces the movement of anchors in subsequent loading stages. When anchors are recycled at a load ratio level less than the pre-cycling load, the movement of anchor in recycling phase are very much reduced, but if the recycling is done at a higher load ratio level, the effect is not that much pronounced and the anchors behave as if they were not subjected to any cycling load in the past. Anchor subjected to cyclic loading and then monotonic pullout shows an increase in initial stiffness, whereas the peak pullout load was found to decrease marginally over that of an anchor not subjected to any cyclic loading. For the present test conditions, the relative post-cyclic stiffness of anchors is found to vary from 1.169 to 1.327.     

Influence of Frequency on the Behaviour of Plate Anchors Subjected to Cyclic Loading

This article reports the response of embedded circular plate anchors to varying frequencies of cyclic loading. The effects of time period of loading cycles and pre-loading on movement of anchors and post-cyclic monotonic pullout behavior are studied using a model circular (80 mm diameter) plate anchor, buried at embedment ratio of six in a soft saturated clay. The frequencies of loading cycles have showed considerable effect on movement of anchors. For given duration of loading, higher frequency cycles cause more movement of anchor than lower frequency cycles. Pre-loading reduces the movement of anchors in subsequent loading stages. When anchors are recycled at a load ratio level less than the pre-cycling load, the movement of anchor in recycling phase are very much reduced, but if the recycling is done at a higher load ratio level, the effect is not that much pronounced and the anchors behave as if they were not subjected to any cycling load in the past. Anchor subjected to cyclic loading and then monotonic pullout shows an increase in initial stiffness, whereas the peak pullout load was found to decrease marginally over that of an anchor not subjected to any cyclic loading. For the present test conditions, the relative post-cyclic stiffness of anchors is found to vary from 1.169 to 1.327.     

Settlement Prediction of Surcharge Preloaded Low Embankment on Soft Ground Subjected to Cyclic Loading

This article studies the effect of dynamic cyclic loading and surcharge preloading method on the post-construction settlement of low embankments. Soil samples obtained from the soft ground under an embankment were consolidated by surcharge preloading followed by static and dynamic cyclic loading in the odometer. The results show that the consolidation deformation of the soil samples is independent of the frequency of the dynamic cyclic loading, which was simulated to follow the half-sine wave, and this is consistent with the energy concept. The post-construction settlement increases with increasing amplitude of cyclic load and the effectiveness of surcharge preloading depends on the difference between magnitude of surcharge and amplitude of the cyclic load. Based on the consolidation theory combined with the test results, a formula has been proposed to compute the post-construction settlement of a low embankment under cyclic loading.     

Validation of Practice Oriented Models and Influence of Soil Stiffness on Lateral Pile Response Due to Kinematic Loading

Earthquakes usually cause both inertial and kinematic loading of pile foundations. Inertial loading and lateral pile response can be predicted to a certain extent by lateral pile load tests for important engineering projects. However, there is no accepted in situ assessment method for pile behavior due to kinematic loading. Therefore, it is important for geotechnical engineering practice to validate the practice oriented models and examine the influence of soil strength parameters on the performance of kinematically loaded piles due to lateral spreading. For this purpose, a well-documented case of full-scale lateral spreading test conducted at Port of Tokachi in Japan by Ashford et al. (2006 Ashford , S. A. , T. Juirnarongrit , T. Sugano , and M. Hamada . 2006 . Soil-pile response to blast-induced lateral spreading. I: Field test . Journal of Geotechnical and Geoenvironmental Engineering 132 ( 2 ): 152 – 162 . [Google Scholar]) is selected as a primary reference in terms of test data and site conditions. Four p-y analyses are performed using a special purpose software based on finite difference technique. The first two investigate the employment of different p-y curves suggested in the literature. The third one investigates the influence of variations in internal friction angle and undrained shear strength. In the fourth analysis, liquefied shear strength and residual shear strength approaches are utilized for the liquefiable layers and their effects are investigated. In all analyses, mobilized lateral pressures in non-liquefied layers are also scrutinized. The results of the analyses are discussed and compared with the measured values in the field. Finally, conclusions are given based on the analyses and discussions.     

Lateral dynamic response of a partially embedded pile subjected to combined loads in saturated soil

In this article, an analytical solution is proposed to investigate the lateral dynamic response of a pile which is partially embedded in saturated soil layer and subjected to combined lateral and vertical loads. The saturated soil is described by Biot’s poroelastic theory and the resistance of soil is derived by potential function method. The governing equation of the pile is solved by coupling soil resistance and continuity conditions between the pile and the soil. The dynamic impedances of the pile are then obtained through transfer matrix method. To verify the validity of the proposed procedure, the present solution is compared with available solution for an idealized case. Finally, a parametric study is performed to investigate the effects of various parameters on the stiffness and damping properties of the pile-soil system. It is found that permeability of the soil and vertical load has significant effects on the dynamic response of the pile.     

Field and Theoretical Study of the Response of Super-Long Bored Pile Subjected to Compressive Load

In this article, two full-scale pile loading tests were conducted to observe the field performance of the super-long bored piles, and a simplified approach for nonlinear analysis of the load-displacement behavior of a single pile was presented. The field tests on piles indicates that, under the maximum test load, more than 70% of the pile top settlement is caused by the compression of pile shaft. For practical purposes, the pile top settlement can be reduced through improving the pile shaft strength. When the load reaches the maximum test load, the proportion of the load carried by the pile tip is approximately 30%. The super-long pile is functioning as an end-bearing friction pile. The skin friction at shallow depth is fully mobilized and decreases from a peak value with increasing load. However, the skin friction of deeper soil is not fully developed due to less relative displacement. Furthermore, a BoxLucas1 model is used to capture the relationship between unit skin friction and pile-soil relative displacement, whereas a hyperbolic model is used to describe the relationship between toe stress and pile base displacement. Based on the BoxLucas1 model and the hyperbolic model, a load transfer method is used to clarify the response of a single pile, and a computational flow chart is developed. The efficiency and accuracy of the present method is verified using the field tests on piles. The proposed simple analytical approach is economical and efficient, resulting in savings in time and cost.     

A Model Test on the Behavior of a Static Drill Rooted Nodular Pile Under Compression

A static drill rooted nodular pile is a new type of composite pile foundation with high bearing capacity, and mud emissions can be largely reduced using the static drill rooted method. This report presents a model test on the behavior of this composite pile in a test box. The load-displacement response, axial force, skin friction, and mobilized base load are discussed in the report; in particular, the force in the cemented soil was investigated based on the measured data. Moreover, the finite element software ABAQUS was used to help investigate this behavior more thoroughly. It was determined that the function of the cemented soil around the pile shaft was different from that at the enlarged pile base; the stress in the cemented soil around the shaft increased suddenly when nearing the pile base; the ultimate skin friction obtained in the model test was larger than that estimated in the field test; and the relative displacement between the precast nodular pile and the cemented soil could be ignored during the loading process, which corresponded to the result of the field test and demonstrated that the nodular pile and cemented soil act as one entity during the loading process.