板翼动力锚沉贯深度模型试验研究

板翼动力锚是依靠自重完成安装并靠自重和海床土的抗力来锚固的新型动力锚。板翼动力锚高速(15~25 m/s)贯入地基过程中涉及到高应变率、流固耦合、土体软化和大变形等难题,模型试验可避免上述计算困难,能直接得出不同的贯入速度所对应的沉贯深度。本文首先推导了模型相似关系,然后在常规重力条件下,进行了两组26个工况的板翼动力锚在均质黏土中动力安装过程的模型试验,根据试验结果确定了率效应参数的取值范围,并研究了每一项受力对沉贯深度的影响。最后提出了在均质黏土中预测板翼动力锚沉贯深度的经验公式。     

海上风电支腿船单桩沉桩技术

目前我国海上风电开发已经进入了规模化、商业化的发展阶段,海上风电的建设呈现由近海到远海,由浅水到深水的趋势。在响水、东台海上风电场中,均采用稳桩平台定位、起重船吊打工艺。文章结合某海上风电工程深水条件下大直径单桩沉桩施工情况,介绍自带定位抱桩器的1000t支腿起重船沉桩施工技术。     

粉土中吸力桶沉贯阻力与土塞失稳机理研究

针对粉土中吸力桶在吸力沉贯中的两个关键性问题——沉贯阻力和内部土体稳定性,在自行研制的试验平台上进行了一系列吸力桶沉贯模型试验。试验结果表明,粉土中吸力沉贯时,Andersen所提供的基于CPT锥尖强度的阻力计算公式能较好预测阻力发展趋势,但计算结果偏小;而修正的承载力公式预测结果在沉贯前期与实测值较吻合,沉贯后期预测偏大。吸力沉贯前期,贯入阻力随深度稳步增长,直到贯入深度达到某个临界值后,阻力增长缓慢甚至保持不变。桶内粉土在吸力作用下的失稳机理与黏土或砂土不同,在渗透力作用下表现为从土层表面开始的自上而下管涌或渗流侵蚀。沉贯后期,端部土体在较高水头差下发生失稳并向桶内流动,造成了桶内土体密度降低,端阻力与内壁摩阻力降低,总贯入阻力主要由外壁摩阻力提供。并结合有限元模拟对上述实验现象的内在机理进行了解释。     

粘土中吸力锚沉贯阻力与土塞形成试验研究

针对粘土中吸力锚沉贯的两个关键性问题--沉贯阻力和土塞形成过程,在自行研制的试验平台上进行一系列吸力锚沉贯室内模型试验.试验结果表明,负压抽吸对筒壁内部土体的影响较大,而对外侧土体的影响很小;由压力沉贯向吸力沉贯转换后,土体阻力会先降低,再随着沉贯的进行逐渐增大,并超过采用压贯方式的土体阻力;前期压贯深度的变化带来了不同的内部泥面下陷,这对吸力沉贯开始阶段的土塞发展影响不大,当土塞加速隆起后,压贯越深的情况土塞发展越迅速;在粘土中进行吸力沉贯时,API规范对最大容许吸力估算较为准确,但是需提供比API规范更大的沉贯吸力才能保持沉贯的进行,而且沉贯过程中土塞的高度大于由于简裙下插置换土体所带来的高度.     

渤海湾海上风电场大规模超长钢管桩沉桩技术与控制

随着海上风电的蓬勃发展,如何提高沉桩质量与施工工效是需要研究的问题。唐山乐亭菩提岛海上风电场300MW 示范工程作为渤海湾第一个海上风电场,施工前期通过对渤海湾水文、地质分析,对沉桩相关设备、施工流程、施工质量控制点等的分析,克服了水深、涌浪大、地质条件差、钢管桩长等难点,确保了15个承台共120根钢管桩的沉桩进度与质量,得到了业主的好评。文章总结优化了渤海湾海上风电场沉桩相关技术与控制难点,为后续渤海湾海上风电场沉桩施工提供了重要施工经验与保障。     

动力锚在斜坡地基上的沉贯特性

水上浮式结构都需要锚固基础来定位.动力锚依靠重力以自由落体的方式安装,是一种自安装锚固基础,具有安装过程简单高效的优点.通过1g模型试验研究了自行研制开发的板型动力锚在斜坡地基上的沉贯过程,分别考虑了基床坡度、锚柄方位和贯入速度对锚最终偏角的影响.结果表明:基床的坡度越大,锚的最终偏角也越大,但基床坡度对动力锚最终偏角影响有限,对动力锚的安装和承载能力影响较小.当贯入速度相同时,锚柄平行坡面时锚的最终偏角最小,锚柄指向坡外时锚的最终偏角最大;当基床坡度相同时,锚的贯入速度越大,锚的最终偏角越小.     

海上风电吸力基础在分层土中的沉贯特性研究综述

吸力基础与海洋工程大直径钢桩相比,具有成本低、安装周期短、对环境影响小、不受海况影响及可回收再利用等优点,近年来在海上风电工程中得到推广应用。吸力基础沉贯至海床预定位置,是其发挥承载力和确保服役稳定性的前提。海床地基土体常以分层土形式分布,且各层土体强度、压缩性和渗透性等存在显著差别,导致吸力基础吸力沉贯机理非常复杂。明确吸力基础在分层土中沉贯特性,有助于指导吸力基础在海上风电工程中的推广应用。对目前吸力基础在分层土中沉贯特性研究进行综述和总结,归纳了其沉贯机理研究进展,并对影响吸力基础在分层土中沉贯因素进行了分析;提出了分层土中吸力基础沉贯的研究方向和改进的沉贯方法。     

潮间带钢管斜桩吊打导向装置与沉桩参数研究

钢管斜桩是潮间带风电的常用基础形式,常采用吊打沉桩的方式。文章针对潮间带吊打沉桩方式的难点开发吊打导向装置,并总结沉桩参数的确定方法。该导向装置包括定位桩、定位架和调向限位架,总体平面布局为六边形,可一次定位并完成整个风电基础的基桩施工,既能可靠保证桩的施工精度,又能极大地提高施工效率和降低安全风险;在应用该施工关键装备时,采用GRLWEAP打桩分析功能确定桩顶动荷载,采用有限元软件建立导向装置有限元模型,对导向装置和沉桩参数进行分析,从而实现斜桩顺利沉桩的目的。该装置和方法已成功应用于越南朔庄一期海上风电场项目,为潮间带风电钢管斜桩吊打施工提供沉桩装备和方法经验。     

水平循环荷载作用下单桩动力特性的数值模拟

采用修正的p-y曲线方法，分析了桩基础振动过程中桩土之间由于土体塑性变形导致的桩土脱开现象，给出了计算桩土脱开现象的数值模拟方法，并据此分析计算了中国渤海湾JZ20－2MUQ平台的桩基础动力特性，得到了桩基础振动过程中桩土脱开的区域，分析了桩土之间的脱开对桩基础动力响应的影响等问题。     

大直径钢管桩土塞效应的判断和沉桩过程分析

港口工程和海洋工程中出现了越来越多的大直径超长钢管桩。由于这种桩直径较大,土塞的形成对桩的可打入性和承载力有较大的影响。鉴于此,根据大直径和超大直径钢管桩土塞性状的特殊性,考虑了桩直径对侧壁摩阻力、端阻力的影响,引入了尺寸效应系数,重新建立了土塞微分体的静力平衡方程,提出了采用改进的静力平衡法进行土塞效应判断,同时采用波动方程法近似模拟土塞与桩管内壁的相互作用,建立了简化的土塞与桩壁相互作用模型,并用该方法进行实际工程的打桩分析,分析结果表明该方法对土塞效应的判断、打桩过程的预测等与工程实测数据吻合较好。     

大直径超长管桩打桩过程中土塞性状研究

大直径超长桩的可打入分析是海洋平台打桩施工顺利进行的重要保障,土塞是否闭合的判断对于桩基可打入性分析具有较大的影响,因此,合理准确的土塞判断结果对提高桩的可打入分析的准确性具有重要的意义。以现场静力触探(CPTU)试验数据为依据,采用孔扩张理论推导了基于CPTU测试结果的桩端土的极限承载力计算公式;在求解桩端土体承载力时考虑了管桩与土体的刚度差异,同时考虑到打桩过程中的土体扰动。采用Randolph推荐的方法得到了土塞阻力,将两者进行比较,进而判断土塞的状态。通过实际工程的实测数据,对各个土层的土塞状况进行了判别,并根据判别情况采用波动方程的方法对桩基的可打入性进行了分析,将预测结果和现场的打桩记录进行了比较。计算结果显示,提出的方法与实测结果更为接近,有效地提高了桩的可打入性的预测精度。     

Pit bearing capacity effect on status of soil plug during pile driving in ocean engineering

Foundation piles of the offshore oil platforms in the Bohai Bay are usually longer than 100 m with a diameter larger than 2 m.Driving such long and large-sized piles into the ground is a difficult task.It needs a comprehensive consider ation of the pile dimensions,soil properties and the hammer energy.Thoughtful drivability analysis has to be performed in the design stage.It has been shown that judging whether the soil column inside the pile is fully plugged,which makes the pile behave as close-ended,strongly influences the accuracy of drivability analysis.Engineering practice repeatedly indicates that the current methods widely used for soil plug judgment often give incorrect results,leading the designers to make a wrong decision.It has been found that this problem is caused by the ignorance of the bearing capacity provided by the soil surrounding the pile.Based on the Terzaghi’s bearing capacity calculation method for deep foundation,a new approach for judging soil plug status is put forward,in which the surcharge effect has been considered and the dynamic effect coefficient is included.This approach has been applied to some practical engineering projects successfully,which may give more reasonable results than the currently used method does.     

The Effect of the Propeller Jet on Pile Groups简

The objective of this study is to determine the effect of jet propeller on the damage of berthing structures combined of armoured slope with pile groups. For this purpose, scour measurements were performed for four types berthing structures, which were armoured slope with tandem arrangements of piles for two and three piles and with side by side arrangements of piles for two and three piles. The effect of gap between piles on damage was investigated. The damage level induced by propeller jet between piles was determined. The gaps were 1, 2, 3, and 4 times the pile diameter. Three different values of Rpm （690, 820, and 950） were chosen for the tests. The diameter of circular piles is 40 mm. The slope ratio was 1/3 and the diameter of propeller was 10 cm.     

Influence of large-diameter pipe pile driving on surrounding marine soils and adjacent submarine pipelines

Abstract

With the large-scale development and utilization of ocean resources and space, it is inevitable to encounter existing submarine facilities in pile driving areas, which necessitates a safety assessment. In this article, by referring to a wharf renovation project as a reference, the surrounding soil response and buried pipe deformation during pile driving in a near-shore submarine environment are investigated by three-dimensional (3D) numerical models that consider the pore water effect. Numerical studies are carried out in two different series: one is a case of a single pile focusing on the effect of the minimum plane distance of the pile–pipe, and the other is a case of double piles focusing on the effect of the pile spacing.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

海洋平台大直径钢管桩打桩过程有限元分析研究

近年来海上工程的规模越来越大,为了满足工程需要,桩基设计常常采用大直径,大长度的钢管桩。打桩过程是个相当复杂的过程,不仅涉及到几何非线性、材料非线性、边界非线性,而且是个动力过程。有限元法在处理打桩分析方面具有很强的优势,采用PLAXIS对不同条件下的打桩问题进行了动力模拟分析。分析显示在打桩过程中,桩端土体会产生较大的水平位移和竖向位移,桩端土体和靠近桩端的部分土塞内会产生较大的超孔隙水压力。在砂土中,停锤较短时间也会使孔压迅速消散,这也是打桩中间的停锤会造成后续打桩困难的主要原因。     

Efficiency analysis of open trench for impact pile driving through a single-variable method

Abstract

The ground vibrations during pile driving operation have a drastic potential to undermine the surrounding structures both in land and reclaimed land. Particularly, reclaimed land necessitates ample application of pile driving due to the weak land condition. To prevent the structural damage, attenuation of the ground vibrations to an allowable level through active isolation of circular open trench is the scope of this study. In this research, finite element simulations of continuous impact pile driving process from the ground surface was executed with particular attention to the pile-soil interaction, and thereby, the efficiency of open trench application in attenuation of the unsafe distance of different structures was surveyed using the vibration sensitivity degree. Regarding the crucial parameters of an open trench (depth, width, and location), it was concluded that a sufficient high depth can attenuate the unsafe distance up to 68%, the trench width variations are less effective, and an average pile-trench distance is the most efficient option. The excavation volume was also concluded as another crucial parameter in open trench design which takes all three parameters into account. The trench depth equal to the pile’s maximum critical depth of vibration was inferred for an optimum design.     

雷诺数对圆形渐缩喷嘴湍流射流的影响

The present study systematically investigates by experiment the influence of Reynolds number (Re) on a turbulent jet issuing from a smoothly-contracting round nozzle. Measurements were performed for seven Reynolds numbers varying from Re = 4,050 to Re = 20,100 using single hot-wire anemometry and over an axial distance of 30 nozzle exit diameters. Although all the exit velocity profiles are of "top-hat" shape, these measurements reveal significant dependence on Re of the exit and downstream flows. The effect of Re on both the mean and turbulent fields is substantial for Re ＜ 10,000 and becomes weak beyond Re = 10,000. The length of the jet’s potential core and the far-field rates of decay and spread all depend significantly on Re.     

V⁃H荷载作用下海洋平台吸力式桩桶桩土承载特性研究

用于海洋平台的吸力式桩桶基础作为一种新型平台基础正逐渐成为人们研究的重点。为研究吸力式桩桶单桩基础的受力特性,对V-H（竖向—水平）联合荷载作用下的吸力式单桩基础桩土的承载特性进行了数值模拟,并将数值模拟的有限元解通过与API规范中对p-y曲线的计算方法进行对比来验证有限元模型的可行性,最后采用分级作用力的加载方式对其破坏包络曲线进行绘制,并推导出相应的函数表达式。研究表明,采用ABAQUS有限元分析软件对吸力式桩桶进行数值模拟是可行的,随着对吸力式桩桶所施加V-H联合荷载的不断增大,吸力式桩桶所能体现的应力和弯矩极限值也在随之增大,其位移变化主要在施加荷载的区域附近,最后在联合荷载作用下所体现的极限承载状态,即包络曲线大致呈四分之一的椭圆形状。     

Dynamic response of a poro-elastic soil to the action of long water waves: Determination of the maximum liquefaction depth as an eigenvalue problem

In this work, a theoretical analysis of the dynamic response of a poro-elastic soil to the action of long water waves is conducted. For some combinations of the physical parameters of the soil and the water waves, the vertical stress tends towards zero at a certain unknown depth in the soil, as measured from the top of that medium. Under this condition, the liquefaction of the soil is imminent, at which time the excess pore pressure is essentially equal to the overburden soil pressure. Physical problems of this type have been widely studied in the specialized literature. However, most major studies have focused on solving the governing equations together with a liquefaction criterion. Here, the maximum momentary liquefaction depth induced by long water waves is considered as part of the problem, which is treated as an eigenvalue problem. To solve this problem, the governing equations are written in dimensionless form. The theoretical results show that for long waves, the horizontal displacements are smaller in magnitude than the vertical displacements, and when the wavelength or wave period increases, the maximum liquefaction also increases. Analytical solutions for the excess pore pressure and the horizontal and vertical displacements are obtained. The analytical results for the pore pressure are found to be very close to the analytical results reported in the specialized literature.