沂源鲁村煤矿千米混合立井围岩稳定性分析与施工措施

基于沂源鲁村煤矿围岩稳定性差,塑性变形量大的实际情况,采用弹塑性力学分析的方法,分析了鲁村煤矿千米混合立井岩石开挖后围岩应力重新分布情况和塑性变形,进而确定是否采用临时支护措施,以确保施工安全。研究表明鲁村煤矿混合井围岩掘进深度大于780 m时,围岩变得不稳定,需要施加锚喷临时支护,同时增加井筒掘进荒断面,预留围岩变形空间。     

Engineering classification of rock masses for the design of tunnel support

SummaryEngineering Classification of Rock Masses for the Design of Tunnel Support An analysis of some 200 tunnel case records has revealed a useful correlation between the amount and type of permanent support and the rock mass qualityQ, with respect to tunnel stability. The numerical value ofQ ranges from 0.001 (for exceptionally poor quality squeezing-ground) up to 1000 (for exceptionally good quality rock which is practically unjointed). The rock mass qualityQ is a function of six parameters, each of which has a rating of importance, which can be estimated from surface mapping and can be updated during subsequent excavation. The six parameters are as follows; theRQD index, the number of joint sets, the roughness of the weakest joints, the degree of alteration or filling along the weakest joints, and two further parameters which account for the rock load and water inflow. In combination these parameters represent the rock block-size, the interblock shear strength, and the active stress. The proposed classification is illustrated by means of field examples and selected case records.Detailed analysis of the rock mass quality and corresponding support practice has shown that suitable permanent support can be estimated for the whole spectrum of rock qualities. This estimate is based on the rock mass quality Q, the support pressure, and the dimensions and purpose of the excavation. The support pressure appears to be a function ofQ, the joint roughness, and the number of joint sets. The latter two determine the dilatency and the degree of freedom of the rock mass.Detailed recommendations for support measures include various combinations of shotcrete, bolting, and cast concrete arches together with the appropriate bolt spacings and lengths, and the requisite thickness of shotcrete or concrete. The boundary between self supporting tunnels and those requiring some form of permanent support can be determined from the rock mass qualityQ. With 8 Figures     

节理岩体圆形隧道滑动区的研究

对于连续介质问题,可以利用Mohr-Coulomb准则很好地解决圆形隧道滑动区问题.但是对于节理岩体问题要复杂得多.由于节理岩体具有复杂的力学特性,因此节理岩体圆形隧道滑动区的确定问题一直都没有很好地解决.节理岩体的力学特性可以很好地用考虑了中间主应力影响的非线性统一强度准则来表达.根据非线性统一强度准则确定了即时摩擦角,进而获得了节理岩体圆形隧道滑动区和支护应力的封闭形式的理论解,并给出了算例.     

Influence of Water Pressure on the Stress State in Stopes with Cohesionless Backfill

The rapid increase of backfill use in underground mines requires a better understanding of the interaction between the fill material and the surrounding rock mass. This is a fairly complex issue as backfill materials are weak compared to the rock mass. This difference in the mechanical behavior induces a stress transfer along the contact area. Previous work conducted on backfilled trenches and mining stopes has shown that basic arching theory can be used to estimate earth pressures in narrow, vertical openings. In this regard, most existing solutions have been developed for dry backfills. However, in many cases, water is present in mine stopes, so its effect should be assessed. In this paper, the authors present a solution to evaluate the stress state in submerged or partially submerged backfilled stopes. The proposed analytical solution is validated against numerical modeling results.     

Nonlinear analysis of NATM tunnel construction with the boundary element method

This paper presents a novel approach to the simulation of NATM tunnel construction using the Boundary Element Method (BEM) as principal numerical method. This new approach has the advantage that only the excavation surface, the possible plastic zones and the tunnel lining have to be discretised. The whole rock mass is represented by the BEM whereas the Finite Element Method (FEM) is used to represent the tunnel lining only. Thus, a general coupling strategy for coupling three-dimensional boundary elements with shell finite elements (shotcrete) and beam finite elements (steel arches) is presented. To achieve realistic results the effect of hydration of the shotcrete and yielding of the steel arches is considered in the excavation process. Furthermore, the nonlinear rock behaviour is modelled more realistically by using a powerful hierarchical constitutive model which considers a large range of rock materials. The combination of these ideas results in higher user-friendliness and efficiency. Some verification tests and practical applications in tunnelling are presented.     

喷锚支护在水工隧洞施工中的应用浅说

简要地介绍了对水工地下洞室施工中对围岩不稳定体,即碎裂岩体、松动岩体、软弱结构面、楔形体结构面等围岩喷锚支护结构的作用,喷锚支护结构的使用。     

On the Application of the Novel Thin Spray-on Liner (TSL): A Progress Report in Mining Operations

Stability is the main problem in underground excavations that can result in rock-related accidents or closure of mines. This is often controlled by the geological condition of the rockmass and the in situ stress field where excavation is being carried out. Over the years, conventional support systems such as bolts, shotcrete and mesh have been the standard support systems used in difficult ground conditions to maintain stability of underground openings. The novel Thin Spray Liner (TSL) is a technology with an improvement in terms of support capabilities for difficult geological conditions. This technology is predicted to replace conventional support systems, as it offers a significant yielding capacity that is better than that of the traditional techniques of controlling strata. The performance of the TSL lies between that of shotcrete and wire mesh. The TSL has numerous advantages regarding rock reinforcement such as rapid curing period, fast application, high tensile strength, high adhesion properties that prevent movement of rock keyblocks, improved cycle times, reduction in material-handling compared to shotcrete, and a significant ability to penetrate joints. These advantages increase the allowance for mechanisation and improvement of safety in excavations. Despite various benefits of TSLs, there are shortcomings which make end-users to be sceptical about the technology. This study provides a detailed review of the mechanism, properties, composition and types, as well as the general and mining applications of TSLs. It also describes the challenges faced by the mining industry and other end-users in accepting the technology as a solution for stability issues in underground openings. In addition, some insightful suggestions are made as recommendations for future work on the development of suitable, effective and efficient thin surface rock support technology within limitations/constraints.

     

Support capacity of wedges along tunnels of Egnatia highway

Four tunnels along the under construction Egnatia highway, were studied in N. Greece (Polymylos and Vassilikos areas). The concept was to investigate the changes of the safety factors and the support ability of the wedges, regarding to their dimensions, taking also into account the spacing of the discontinuities. The safety factors of the wedges, as well as their ration before and after support, were correlated significantly with the weights and the volumes of the wedges, using powered regressions. According to these results the efficiency of the support ability of the shotcrete is very high in cases where the rock mass is cracked. There is no difference in safety factor between using only shotcrete and using shotcrete and rockbolts for supporting relatively small wedges. This ability decreases dramatically for bigger wedge volumes, over 20m³ and of weights in cases where these are over about 40tns. In these cases, the shotcrete presents low efficiency and bolting is the main support measure performed.     

松动岩体工程特性研究——以雅砻江楞古水电站松动岩体为例

为了对松动岩体的工程特性进行系统研究,以楞古水电站厂址区边坡为例,对该边坡岩体进行了详细的地质编录和物理勘探试验,重点对节理裂隙的空间发育规律、镶嵌结构和碎裂结构岩体的发育深度及空间分布、软弱结构面发育分布规律以及边坡已有变形破坏特征这四个方面进行了系统的统计和分析,认为松动岩体是区域断裂活动和浅表生改造的结果,岩体工程效应差、变形模量低;同时结合应力测试、声波测速、高密度电磁勘探等试验成果进行分析,结果显示松动岩体具低波速（波速大部分小于3 000 m/s）、低应力（最大主应力不超过20 MPa）、强透水性（透水性系数大于10 L/（min·m·m））。认为岩体破碎主要受断层及节理裂隙影响,分析了岩体破裂松动的演化过程及特征。     

峡谷地区大型地下洞室群岩体初始地应力场反演分析

合理地确定地下洞室群岩体初始地应力场对于地下洞室群的总体布局、支护设计有着重要的意义。本文提出了一种依据少量实测地应力资料反演地下洞室群岩体初始地应力场的方法。这种方法假设远古地形是一无起伏的夷平面,认为岩体初始地应力场主要由处于远古地应力状态下的远古地形经过漫长的地形剥蚀形成,而远古地应力场由地质构造运动和岩体自重形成。以有限元数值分析为基本手段,提出了可以考虑构造运动、岩体自重和地形剥蚀等多因素的岩体初始地应力场反演思路。通过某水电站地下厂房区域岩体初始地应力场反演的工程实例分析,验证了这一方法的可行性和实用性。     

隧道喷射混凝土强度增长规律及硬化速度对初期支护性能影响试验研究

隧道结构的围岩-支护特征曲线理论表明,初期支护强度变化及支护时机将极大地影响隧道周围围岩的变形及应力分布。相应地,作为初期支护重要组成部分的喷射混凝土,其喷射后的强度增长变化规律及硬化速度也极大地影响着围岩的变形及应力重分布。为探明喷射混凝土的强度增长规律及其硬化速度对初期支护性能的影响,结合隧道工程实践,进行了一系列喷射混凝土现场试验,建立了喷射混凝土强度和弹性模量增长规律,确定了喷射混凝土硬化速度对初期支护性能的影响规律。分析表明：（1）隧道喷射混凝土早期强度发展较快、较平稳,24 h抗压强度平均值为6.4 MPa,48 h抗压强度平均值为11.4 MPa。（2）在软弱围岩中提高喷混凝土的早期强度十分重要,是控制围岩变形和稳定的关键,喷混凝土早期强度越大,隧道初期支护作用越明显。（3）喷混凝土硬化速度对控制拱顶沉降变形效果较显著。与慢速硬化相比,喷射混凝土快速硬化时拱顶沉降减少10.4%,拱脚处减小17%,边墙水平收敛减少了30.7%。（4）喷射混凝土硬化速度对控制围岩塑性变形方面差异较小。（5）应充分考虑喷射混凝土的强度硬化过程,不考虑喷射混凝土硬化速度会在一定程度上高估初期支护性能,使其相应支护结构位移明显小于考虑硬化速度时相应的结构位移。     

Stability analysis and optimization of the support system of an underground powerhouse cavern considering rock mass variability

Input parameters, such as rock mass strength parameters and deformation modulus, considered in the design of underground openings involve some uncertainty. The current uncertainty in these parameters is due to the inherent variability of these parameters. To quantify these parameters and design underground openings, the statistical methods must be utilized. In this research, a statistical method was used to define the GSI of rock mass (Geological Strength Index), block volume (V_b), and joint conditions (J_c). Using the GSI distribution function obtained from field data and intact rock strength characteristics, the statistical distribution functions of rock mass parameters were defined using the Monte Carlo method. The statistical analysis of the stability in Azad-pumped storage powerhouse cavern was carried out through the point estimate method. The appropriate support system was suggested according to the support pressure and the plastic zone around the cavern. This study showed the application of the statistical method, by combining the uncertainties of the intact rock strength and discontinuity parameters, in the assessment of the strength and deformability of rock masses and the support selection process in comparison with the deterministic methods.     

The application of rock mass classification systems to underground excavation in weak limestone, Atatürk dam, Turkey

The Atatürk dam was built across the Firat River on clayey limestone. A grout curtain, providing impermeability in the left and right abutments, was done in grouting galleries. The well known rock mass classification systems for tunneling purposes [rock structure rating (RSR), rock mass rating (RMR) and rock mass quality index (Q)] were used to classify the rock mass along these galleries. Based on RSR, RMR and Q values, the rock masses in the galleries have been classified into three different classes. Correlation between the three classification systems is discussed and suggestions are made for using rockbolt, shotcrete with wiremesh and steel ribs for supporting the rock mass.     

Effects of pre-existing discontinuities on the residual strength of rock mass – Insight from a discrete element method simulation

When rock failure is unavoidable, the designer of engineering structures must know and account for the residual strength of the rock mass. This is particularly relevant in underground coal mine openings. Pre-existing discontinuities play an important role in the mechanical behavior of rock masses and thus it is important to understand the effects of such pre-existing discontinuities on the residual strength. For this purpose, the present study demonstrates a numerical analysis using a discrete element method simulation. The numerical results indicate that fracture intensity has no significant influence on the residual strength of jointed rock masses, independent of confining conditions. As confining pressures increase, both peak and residual strengths increase, with residual strength increasing at a faster rate. The finding was further demonstrated by analyzing documented laboratory compressive test data from a variety of rocks along with field data from coal pillars. A comprehensive interpretation of the finding was conducted using a cohesion-weakening-friction-strengthening (CWFS) model. The effect of rock bolts on rock mass strength was also evaluated by using a discrete element method model which suggested that rock bolts can significantly increases residual strength but have limited effect on increasing the peak strength of rock masses.     

公路隧道型钢喷射混凝土初期支护安全评价研究

公路隧道常采用复合式衬砌,按“新奥法”原理进行设计和施工。对于软弱围岩段,采用型钢拱架（或格栅拱架）+注浆+锚喷网联合初期支护形式,型钢喷射混凝土初期支护的安全性评价方法是实现支护动态设计的关键。对初期支护安全性评价进行系统研究,建立了型钢喷射混凝土安全性评价数值计算方法。首先,根据监测数据分析围岩最终沉降量、水平收敛值,作为围岩力学参数反演的依据;其次,采用反演的力学参数,通过地层-结构法数值计算型钢拱架喷射混凝土初期支护内力;最后,采用型钢混凝土安全系数计算方法计算和评价初期支护安全性。研究发现,型钢拱架喷射混凝土初期支护能发挥型钢强支护作用,而喷射混凝土达到设计强度后,混凝土起主要支撑作用,型钢间距对提高初期支护安全系数不显著。     

陡倾坡外弱面控制的斜坡滑移-剪损变形破坏模式

斜坡变形破坏和稳定性分析是各类工程建设中高度关注的问题.采用实例调查、理论分析、数值计算等技术方法,以雅砻江某水电工程坝址区右岸顺层岩质斜坡为例,研究总结了斜坡发育滑移-剪损变形破坏的成因机理、发育特征以及与弱面倾角和发育深度的关系.研究表明,滑移-剪损变形破坏通常发育在力学性能相对较差的薄层、互层状结构的顺层岩质斜坡或斜坡强-弱风化带内.斜坡发育滑移-剪损变形破坏与陡倾坡外弱面的倾角和发育位置密切相关.倾角在45°~65°之间或距斜坡表部水平距离小于80 m的弱面对斜坡发育滑移-剪损变形破坏的影响控制作用明显,并且弱面距斜坡表部水平距离比弱面倾角对斜坡发育滑移-剪损变形破坏的影响控制作用更强.研究成果可补充完善岩质斜坡变形破坏类型,具有重要的工程意义和实践价值.      

核废料地质处置概念库锚喷支护坑道热-水-应力耦合效应的二维离散元分析

假定一个核废料地质处置库位于具有一定水头的饱和节理岩体中,开挖完闭施作系统锚杆和喷混凝土支护。对坑道建造和一个50年期的热-水应力（T-H-M）耦合运营过程,使用UDEC程序进行数值模拟,分析无、有支护时近场围岩中的应力、变形、塑性区、温度、渗流的变化状态,以及不同场（温度、渗流、应力）耦合条件下的锚杆和喷混凝土中的承载情况。结果显示,喷混凝土和系统锚杆支护不仅具有常规的支护功能,并且可阻滞地下水从坑道表面的自由渗出,使得围岩中塑性区减小,裂隙水压力和温度升高;相比于应力单场作用的情况,在热-水-力耦合的条件下洞室围岩的稳定性下降,支护结构的受力状况变差。     

A Statistical Analysis of Fragmentation After Single Hole Bench Blasting

Summary The purpose of this study is to statistically correlate the fragmentation gradient () and average fragment size () with the blasting test parameters for rock masses having different characteristics. Blasting tests were conducted in limestone exposed during the highway construction between Tarsus and Pozanti (Turkey). Three test sites were classified as poor rock, good rock, and very good rock according to their RMR ratings. The selected blasting test parameters that affect the degree of fragmentation were burden, bench height and ANFO charge. After each blast, the muckpiles were screened and fragment size distribution graphs were plotted. Yates' method was applied for experimental design and analysis of variance. The single and combined effects of blasting test parameters were analyzed through the Yates' tables and significant and non-significant treatment combinations were determined for different rock masses. Some conclusions drawn from this research are: 1. The increase of RMR ratings promotes fragmentation, hence, increases blasting efficiency. 2. In rock masses of low RMR ratings, the volume of broken material is large, but fragmentation into small sizes is low. The opposite is true for rock masses of high RMR ratings. 3. The length of charge column is the significant factor affecting the average fragment size regardless the type of rock mass and is more significant in very good quality rock mass.     

软弱围岩隧道取消系统锚杆的现场试验研究

在软弱围岩隧道中,提出初期支护结构由钢架+喷射混凝土+钢筋网+锁脚锚杆+纵向连接筋组成,即取消系统锚杆用钢架联结处的锁脚锚杆代替。以包家山隧道为依托工程,采用现场试验的方法,选取2个试验段,进行锁脚锚杆取代系统锚杆后,有、无拱部锚杆的对比试验研究。对比试验的内容包括：隧道初期支护的净空收敛、围岩压力、钢架应力、喷射混凝土应力、锚杆轴力和纵向连接筋应力等。研究结果表明：2个试验段初期支护变形趋于稳定,结构受力安全,说明取消系统锚杆不影响初期支护结构的安全与稳定;拱部锚杆有受拉,也有受压,但受力都不大,最大拉应力仅为钢材极限强度的11.8%,其支护作用不明显;锁脚锚杆大部分受拉,最大值达到191 MPa,钢架支护作用明显,在支护体系中发挥着重要作用。取消系统锚杆减少了施工工序,降低了工程造价,缩短了工序循环时间,有利于及早封闭围岩以形成完整的支护结构。经济价值和社会效益显著。     

强震区软弱破碎千枚岩隧道系统锚杆支护作用效果分析

以在建的穿越5•12强震区发震断裂带的广甘高速公路杜家山隧道为工程依托,选取20 m典型围岩区段为试验段,对有、无系统锚杆时的洞周位移、锚杆轴力、钢拱架内力、围岩与初支接触压力、及其二衬内力进行实测对比分析,探讨锚杆支护作用效果不明显的成因,提出了在强震区软弱破碎千枚岩隧道围岩中采用“钢喷”初期支护的支护方案。研究结果表明：设置锚杆的断面,其锚杆轴力值较小,最终洞周变形值及围岩与初支的接触压力值相对偏大,钢拱架和二衬的安全储备相对不足;锚杆的施工不仅在某种程度上加剧了对深部围岩的扰动,而且还延误了喷射混凝土和钢支撑支护对暴露围岩及时封闭的最佳时机;震后深部围岩的震裂损伤和震裂岩体地下水的渗透性增强,致使围岩松弛区域超过了锚杆设置范围,且锚杆与围岩间的黏结力被削弱。