首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 218 毫秒
1.
Appropriate evaluation of shear modulus and damping characteristics of soils subjected to dynamic loading is key to accurate seismic response analysis and soil modeling programs. Dynamic centrifuge experiments were conducted at C-CORE (Memorial University of Newfoundland) centrifuge center to investigate the dynamic properties and seismic response of soft clay and dry loose sand strata. Soft clay with shear strength of about 30 kPa and well graded silica sand at about 35% relative density were employed in a rigid container to simulate local site effects. Several earthquake-like shaking events were applied to the model to evaluate variation of shear modulus and damping ratio with shear strain amplitude and confining pressure, and to assess their effects on site response. The estimated modulus reduction and damping ratio were compared to the predictions of empirical formulae and resonant column tests for both soft clay and loose sand. The evaluated shear modulus and damping ratio were found to be dependent on confining pressure in both soil types. Modulus variation in both soils agreed well with the empirical curves and resonant column test results. However, the sand modulus values were slightly higher than the empirical relations and resonant column tests. This discrepancy is attributed to higher stress and densification of sand during large amplitude shaking applied to the model. The damping ratio at shear strains lower than 0.5% was in reasonable agreement with the empirical curves and the resonant column tests in both clay and sand models, but was generally higher at shear strain larger than 0.5%.  相似文献   

2.
刘飞禹  王攀  王军  胡秀青  蔡袁强 《岩土力学》2016,37(Z1):159-165
为了研究筋-土界面在遭受动力作用时的表现,利用大型直剪仪对土工格栅、土工编织布、土工无纺布和砂土界面进行了一系列循环剪切试验,得到了不同工况下界面的剪切刚度和阻尼比,并探究了循环次数与剪切刚度和阻尼比之间的规律。研究结果表明,同一循环次数时格栅-土界面的循环剪切刚度最大,土工编织布-土界面的阻尼比最大;剪切位移幅值为3 mm时3种竖向应力下界面都呈现出循环剪切硬化的特征,随着循环次数的增加,各竖向应力下的界面阻尼比有趋于某一值的趋势;砂土密实度越大,同一循环次数对应的剪切刚度越大,阻尼比越小,且随着循环次数的增加3种砂土密实度的界面阻尼比有趋于同一值的趋势;循环剪切位移幅值为5 mm的界面发生循环剪切软化现象,剪切位移幅值越大,界面同一循环次数的阻尼比也越大。  相似文献   

3.
尾矿料的动力特性试验研究   总被引:10,自引:0,他引:10  
通过对某铜矿的尾矿料进行动三轴和共振柱试验,研究了尾矿材料动力变形特性,提出了简单实用的孔隙水压力模型,给出了能更加准确地预测尾矿材料的动孔隙水压力的公式,并将其与Seed提出的预测公式进行了比较。在不同密度尾矿料的动三轴试验基础上,分析了相对密度对液化特性的影响,得出了相对密度小于70 %时抗液化强度随相对密度的增加而明显增加的结论。在不同围压下进行动三轴试验,结果表明:在相同的液化振次条件下,围压越高,动剪应力比越低。由共振柱试验可知,尾矿料的阻尼比随着动剪应变幅的增大而增大,而动剪模量随动剪应变幅的增大而减小,动剪模量和阻尼比与动剪应变幅的关系受围压影响不太敏感。  相似文献   

4.
贾鹏飞  孔令伟  王勇  杨爱武 《岩土力学》2013,34(11):3145-3150
随着高速铁路建设的兴起,轨道以及沿线附近建筑物承受低幅值小应变振动荷载的作用。对于小应变振动下土体的有限元计算,如何确定连接应力和应变之间纽带的刚度张量E,对于建立合理的预测模型来分析高速铁路轨道以及沿线建筑物的沉降变形至关重要。低幅值小应变振动下剪切模量G和阻尼比D随剪应变幅值的变化是反映土体刚度及阻尼特征最重要的两个参数。通过共振柱试验发现,振动荷载作用下土体的剪切模量G必须通过振动应变幅值和固结围压共同来确定,即使在小应变(剪应变幅值10-6相似文献   

5.
In the present study, a series of resonant column tests was performed to determine the influence of confining pressure, shear strain and relative density on the dynamic properties and Poisson's ratio of poorly graded clean sand. The tests were performed on the sand specimens of size 50 × 100 mm compacted at relative densities 30, 50 and 75 %. To achieve the corresponding relative density, sand was compacted in 5 equal layers with a specific number of blows. A fixed-free type resonant column apparatus was used to determine the dynamic soil properties at various confining pressures. It has been inferred from the data that the shear modulus (\(G\)) increases with an increase in confining pressure and relative density; and decreases with an increase in shear strain. In addition, damping ratio (\(D\)) decreases with an increase in confining pressure and relative density; and increases with an increase in shear strain. In addition, Poisson’s ratio (\(\nu\)) decreases with an increase in confining pressure and relative density and increases with an increase in the shear strain. The variation of shear modulus with Poisson’s ratio is also discussed. It has been found that there has been a decrease in shear modulus with an increase in Poisson’s ratio of the soil. It is noticed that the small strain shear modulus determined from the present study closely matches with the value determined using the correlations from the literature.  相似文献   

6.
厦门砂土的动力特性研究   总被引:8,自引:0,他引:8  
王权民  李刚  陈正汉  曹继东  方祥位 《岩土力学》2005,26(10):1628-1632
为了探讨厦门砂土的动力特性,对厦门金秋豪园场地的中粗砂和细粉砂做了一系列振动三轴试验,并对同一场地的含泥中砂做了4个共振柱试验。根据试验结果,确定了中粗砂与细粉砂的液化曲线和动本构关系,提出了相应的动孔压模型,得到了含泥中砂在小应变条件下动剪切模量和阻尼比的变化规律。  相似文献   

7.
动剪切模量和阻尼比是工程场地地震安全性评价及地基动力反应分析的重要动力学参数。为评价某海域海洋土的动力学特性,对10.3~84.2 m深度范围内的海底淤泥质粉质黏土、粉砂及细砂开展共振柱试验。利用双对数模型建立了最大动剪切模量随上覆压力的递增关系。研究发现,现有规范的剪切模量比与阻尼比的推荐取值并不适用于海洋沉积土,即使考虑借鉴以往研究成果也必须将其限制在一定的应变范围,并应考虑土体的天然应力状态取值。利用马丁-达维登科夫(Martin- Davidenkov)模型及阻尼比与剪应变的经验关系建立了剪切模量比和阻尼比随剪应变的变化规律,并由此提出了适用于海洋沉积土的5×10-6~10-3应变范围内剪切模量比及阻尼比的推荐值。研究成果可为海洋工程场地的设计、施工及抗震分析提供技术参考依据。  相似文献   

8.
材料状态对干砂小应变特性的影响   总被引:2,自引:0,他引:2  
利用注能虚拟质量(EIVM)共振柱系统进行了干砂小应变特性试验,研究了有效平均正应力、土样密度、剪应变幅值以及荷载往复次数对剪切模量和阻尼比的影响。试验结果表明,剪切模量随有效平均正应力与土样密度的增加而增加,而阻尼比的变化规律则与之相反,并且有效平均正应力对干砂小应变特性的影响程度比土样密度的影响程度大得多;随着剪应变的增加,剪切模量越来越小,而阻尼比越来越大;荷载往复次数对剪切模量基本没有影响,而对阻尼比有较大影响。  相似文献   

9.
利用GDS共振柱试验系统对不同干密度、不同含水率的断层泥试样进行了动剪切模量和阻尼比试验研究。结果表明,使用Hardin-Drnevich双曲线模型能够较好地描述断层泥的动剪切模量随剪应变的变化趋势;随干密度增加,动剪切模量和阻尼比均增大;而随含水率增加,动剪切模量和阻尼比均减小;归一化动剪切模量试验点主要位于Seed和Idriss提出的砂土G/Gmax~γ曲线变动范围内,且与Sun和Seed推荐黏性土曲线变化趋势一致;在半对数坐标系中,阻尼比与动剪应变呈良好的线性关系,并给出了拟合关系式。  相似文献   

10.
The complexity of determining strain associated with shear modulus and damping ratio in torsional tests has been resolved by means of several approaches. The stress integration approach is adequate when generating the plots of equivalent radius ratio versus strain more effectively over any range of strains in resonant column and torsional shear (RC/TS) tests. The stress integration approach was applied for hyperbolic, modified hyperbolic, and Ramberg–Osgood models in evaluating damping ratio. This study showed that using a single value of equivalent radius ratio in evaluating damping ratio is not appropriate. The combined hysteretic‐nonviscous damping model was developed and employed to consider the increased damping behavior at small strains using the stress integration approach. The results suggest that adding viscous behavior has no significant effect strain calculations in RC/TS testing. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

11.
孔纲强  李辉  王忠涛  文磊 《岩土力学》2018,39(6):1935-1940
人工合成透明土材料在支撑岩土工程可视化模型试验技术领域得到了良好的应用。然而,关于该新型材料的动力特性研究仍相对缺少,一定程度上影响了其在动力相关模型试验中的推广应用。基于共振柱、动扭剪试验仪器,开展人工合成透明砂土的动变形与动强度特性试验研究,并与天然砂土及福建标准砂的相关动变形与动强度特性进行对比分析;透明砂土由折射率一致的熔融石英砂和混合油配制而成,混合油由15号白矿物油和正12烷按比例混合而成。试验测定并分析了透明砂土的动剪切模量-应变、阻尼比-应变、动剪切模量-阻尼比等关系曲线,以及孔压、动强度特征。试验结果表明,由熔融石英砂与混合油配制而成的透明砂土的动变形和动强度特性与天然砂土相似,可以模拟天然砂土材料开展动力相关模型试验研究。  相似文献   

12.
钙质砂与钢界面的动力响应对岛礁地质条件下结构物基础的安全与稳定具有重要意义。基于界面环剪仪,开展了一系列钙质砂?钢界面循环剪切试验,探究了法向应力、剪切位移幅值和粒径大小对界面剪切刚度和阻尼比的影响,并与石英砂进行了对比。研究结果表明:法向应力和剪切位移幅值对界面剪切刚度和阻尼比起控制作用;法向应力的增大导致界面剪切刚度增大、阻尼比降低;剪切位移幅值的增大,则导致剪切刚度近似呈反比降低,而阻尼比近似呈对数增大;对于均一粒径的钙质砂,存在着分界粒径,使其剪切刚度和阻尼比的变化规律呈现显著区别;石英砂粒径较大时,其界面剪切刚度和阻尼比与钙质砂明显不同,而粒径较小时两类砂表现出类似的剪切刚度和阻尼比特性。  相似文献   

13.
张炜  李亚  周松望  蒋正波  吴非  梁文洲 《岩土力学》2018,39(7):2413-2423
采用南海北部区域油田场址钻孔原状土样,开展黏土循环动力特性试验研究。结合共振柱与应变控制的循环单剪试验,获取动剪切模量和阻尼比随循环剪应变的变化规律,将最大动剪切模量与原位静力触探的计算结果进行对比。开展应力控制的循环单剪试验,采用对称加载方式获取土样动强度阈值,基于该阈值,通过单、双向加载方式获取土样动强度包络线,并将试验结果与Drammen黏土及世界范围内其余区域黏土进行对比。该研究初步获取了南海北部区域性黏土的循环特性及动力学参数,为南海北部区域油气田结构设计和地质风险评估提供基础资料,掌握了循环动力特性试验方法,为岩土工程动力学试验研究及数据分析提供技术参考。  相似文献   

14.
固结比对黏性土动剪切模量影响的研究   总被引:1,自引:0,他引:1  
孙静  袁晓铭 《岩土力学》2010,31(5):1457-1462
采用共振柱试验方法,对固结比对黏性土最大动剪切模量和对动剪切模量比与剪应变非线性关系的影响进行了研究,并通过土层地震反应计算,初步给出了这种影响对地表反应谱作用的估计。通过对粉质黏土和粉土的系统试验,提出了计算不同固结比粉质黏土和粉土最大动剪切模量的建议公式,并与Hardin公式进行了对比。结果显示,固结比kc >1.0时的最大动剪切模量较kc=1.0时的增长程度明显比Hardin公式要大。与砂土试验结果相比,固结比对黏性土最大动剪切模量影响程度更大。同时,分析了固结比对动剪切模量比与剪应变非线性关系及对地表反应谱的影响。结果表明,固结比对黏性土动剪切模量比与剪应变非线性关系有一定影响,随固结比增加,动剪切模量比非线性关系曲线有一定提高,动剪切模量比值增大,在强地震动作用下的土层反应分析中应考虑实际固结比的影响。  相似文献   

15.
黄河三角洲粉质土的动模量和阻尼比试验研究   总被引:9,自引:2,他引:7  
结合室内共振柱和动三轴实验,对黄河三角洲饱和原状粉质土体(粉土、粉砂、粉质粘土)动模量和阻尼比的影响因素和发展规律进行了详细的研究。研究表明,在粉粒和粘粒含量对动模量的共同影响中,粉粒含量起着举足起重的作用;侧限压力对归一化剪模比和阻尼比的影响均较显著,相比粘粒含量的影响不大。通过与Seed建议的砂土及饱和粘土的G/Gmax~曲线和~曲线进行对比,结果显示研究区的粉质土相比一般的砂土和饱和粘土而言,其动力变形特性更接近于砂土,但是与砂土也存在着非常明显的差异;其发展规律与其他地区沉积粉质土也较为不同,具有明显的区域性。采用修正了的Hard in-D rnevich模型和对数模型分别对G/Gmax~曲线和~曲线进行拟合,给出了三类粉质土的归一化动力变形G/Gmax~/r关系曲线,对模型中有关参数的影响因素做了初步的探讨。  相似文献   

16.
刘飞禹  施静  王军  蔡袁强 《岩土力学》2018,39(6):1991-1998
三明治形加筋土是一种在黏土中加入加筋砂层形成的混合填料形式的新型加筋土。为了研究不同条件下三明治形加筋土筋-土界面的动力剪切特性,采用大型直剪仪对三明治形加筋土进行了一系列循环剪切试验,研究了不同薄砂层厚度、循环剪切幅值和竖向应力对界面剪切特性的影响。试验结果表明:筋-土界面的剪应力峰值随着循环次数的增加而增加,循环周次为10时,薄砂层厚度为5、6、7、8、9 mm的条件下,筋-土界面的剪应力峰值分别为24.84、27.4、27.94、26.33、24.68 kPa,表明薄砂层厚度为7 mm时,筋-土界面在循环剪切阶段的峰值剪应力最大;剪切幅值越大,界面循环剪切的最终剪缩量越大,同一循环次数对应的剪切刚度和阻尼比越小;在不同竖向应力下,界面在循环剪切过程中都发生了循环剪切硬化现象,循环周次为10时,竖向应力为30、60、90 kPa的条件下,筋-土界面的剪应力峰值分别为20.4、25.14、32.96 kPa,表明剪应力峰值随竖向应力的增大而增大,同一循环次数对应的剪切刚度也随竖向应力的增大而增大。  相似文献   

17.
利用DSJ-2型电动四联等应变直剪仪分别进行了不同粒径砂和粘土(方案1)、不同含水量砂和粘土(方案2)的直剪试验,揭示了其接触面的力学特性。试验结果表明:法向应力(σn)、砂粒径大小、砂含水量对接触面的力学特性有着重要的影响。方案1和方案2接触面的抗剪强度和达到剪切应力峰值时的剪切位移随着法向应力的增大而增大,当σn为100 kPa时,粘土和不同粒径砂的接触面剪切应力和水平剪切位移(τ-δ)关系曲线呈现应变软化现象;方案1接触面抗剪强度随砂粒径的减小而降低,方案2在σn为100 kPa时,接触面抗剪强度随砂含水量增加而降低,σn>100 kPa时,接触面抗剪强度随砂含水量增加先降低后变大;方案2在低法向应力下,接触面抗剪强度对应的含水量敏感区间为[10%,15%],且较明显。   相似文献   

18.
Shear wave velocity is one of the important factors representing the dynamic characteristics of soil layers. Hence, many researchers have focused their studies on determining shear wave velocity by direct field measurements or expressions developed by other soil parameters. The shear module and damping ratio of the soil layers also play a similar role in the majority of dynamic soil response analyses. Nevertheless, since they have to be measured in the laboratory by resonant column or cyclic triaxial tests on undisturbed samples, the possibility of preparing such samples and the reliability of the obtained results are of great concerns. In the present study, great effort has been made to determine the above dynamic factors by means of field data obtained from a versatile instrument, namely the seismic piezocone (SPCTU), and to derive expressions correlating them with some parameters obtainable by much simpler instruments. The reliability of laboratory measurements on undisturbed samples is also evaluated. The seismic piezocone test apparatus has been employed to evaluate the soil properties at 1-m depth intervals by means of measuring tip resistance, sleeve resistance, pore pressure and shear wave velocity. The shear module and the damping ratio are calculated using field data. Meanwhile, in order to assess the laboratory measurements of these parameters, some resonant column tests and cyclic triaxial tests on undisturbed samples of the same soil layers have been carried out. In order to compare the field results of shear modulus and damping ratios with those obtained from laboratory tests, the influences of the soil nature and sample disturbance on the conventional laboratory methods are evaluated and discussed. The shear wave velocity is correlated to overburden pressure and the corrected tip resistance for two groups of fine soils, namely silty clays and carbonate clayey silts, which mainly cover the areas under study in this project, are located in southern parts of Iran near the Persian Gulf. According to the results of the present study, there are narrow limits of shear modulus regarding soils for which the laboratory tests and the field measurements yield approximately the same shear modulus. This limit of shear modulus is about 30–50(MPa) for clay deposits and 70–100 (MPa) for sandy deposits. Also the shear wave velocity can be calculated by a simple expression from total overburden pressure and the tip resistance of simple cone penetration test results conventionally available in many soil explorations prior to engineering practices. However, if the pore pressure inside the saturated soil deposits can be measured by a piezocone apparatus, the shear wave velocity may be calculated using another suggested equation in terms of effective overburden pressure in the present study. Regarding the shear module and the damping ratio, due to the disturbances of the stiff deposits in the sampling process and great deviations of laboratory results from field results, the laboratory measurements of these parameters out of the above limits are not recommended.  相似文献   

19.
开展对水泥土搅拌桩软土地基土体试样的GDS(Global Distribution System)共振柱试验,研究不同剪应变、围压、水泥土置换率对土体动力特性的影响。结果表明,水泥土搅拌桩软土地基土体的动剪切模量G和阻尼比D随剪应变? 变化趋势与软黏土一致,在小应变范围内围压和置换率对土体的动剪切模量G和阻尼比D的影响显著,随着剪应变? 增大,围压和置换率的影响减弱;水泥土搅拌桩软土地基土体的最大动剪切模量Gmax与围压表现出良好的线性关系,围压越大,提高水泥土的置换率对土体最大动剪切模量Gmax增强效果越明显。研究结果可为地区水泥土搅拌桩软土地基土体动力参数的取值提供一定的参考。  相似文献   

20.
Use of scrap tyres in isolation systems for seismic damping, requires a knowledge of the engineering properties of sand–rubber mixtures (SRM). The primary objective of this study is to assess the influence of granulated rubber and tyre chips size and the gradation of sand on the strength behaviour of SRM by carrying out large-scale direct shear tests. A large direct shear test has been carried out on SRM considering different granulated rubber and tyre chip sizes and compositions. The following properties were investigated to know the effect of granulated rubber on dry sand; peak shear stress, cohesion, friction angle, secant modulus and volumetric strain. From the experiments, it was determined that the major factors influencing the above-mentioned properties were granulated rubber and tyre chip sizes, percentage of rubber in SRM and the normal stress applied. It was observed that the peak strength was significantly increased with increasing granulated rubber size up to rubber size VI (passing 12.5 mm and retained on 9.5 mm), and by adding granulated rubber up to 30%. This study shows that granulated rubber size VI gives maximum shear strength values at 30% rubber content. It was also found that more uniformly graded sand gives an improved value of shear strength with the inclusion of granulated rubber when compared to poorly graded sand.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号