Effect of fines content and void ratio on the saturated hydraulic conductivity and undrained shear strength of sand–silt mixtures

The hydraulic conductivity represents an important indicator parameter in the generation and redistribution of excess pore pressure of sand–silt mixture soil deposits during earthquakes. This paper aims to determine the relationship between the undrained shear strength (liquefaction resistance) and the saturated hydraulic conductivity of the sand–silt mixtures and how much they are affected by the percentage of low plastic fines (finer than 0.074 mm) and void ratio of the soil. The results of flexible wall permeameter and undrained monotonic triaxial tests carried out on samples reconstituted from Chlef river sand with 0, 10, 20, 30, 40, and 50 % non-plastic silt at an effective confining pressure of 100 kPa and two initial relative densities (D _r = 20, 91 %) are presented and discussed. It was found that the undrained shear strength (liquefaction resistance) can be correlated to the fines content, intergranular void ratio and saturated hydraulic conductivity. The results obtained from this study reveal that the saturated hydraulic conductivity (k _sat) of the sand mixed with 50 % low plastic fines can be, in average, four orders of magnitude smaller than that of the clean sand. The results show also that the global void ratio could not be used as a pertinent parameter to explain the undrained shear strength and saturated hydraulic conductivity response of the sand–silt mixtures.     

A compression model for sand–silt mixtures based on the concept of active and inactive voids

A compression model for sand–silt mixtures is needed in geotechnical engineering, for example in the analysis and prediction of deformation of levees and embankments due to internal erosion. In this paper, we introduce a novel concept of dividing the voids of a granular material into two hypothetical fractions: active and inactive voids. The active voids are kinematically available to the compression process. The inactive voids are kinematically unavailable to the compression process. The volume of active voids is dependent on the initial density and effective stress level. The volume of inactive voids is dependent on the amount of fines in the mixture. The current paper considers 1-D and isotropic compression behavior of sand–silt mixtures at stress levels lower than 2 MPa, so no substantial particle breakage is expected to occur. To successfully predict the void ratio for a sand–silt mixture during compression loading, we need (1) a mathematical expression for the evolution of the active void ratio during compression and (2) a relationship between the inactive void ratio and fines content of the mixture. For sand–silt mixtures with any amount of fines, the proposed model requires five material parameters, which are determined from two compression tests, and four minimum void ratio tests on sand–silt mixtures with different fines content. The performance of the proposed model is verified for six different types of sand–silt mixture with various fines contents, by comparing the predicted void ratios with the measured data from the experiments. The comparisons show a good agreement between the predictions and the measured data and prove the suitability of the proposed model for the prediction of compressibility of sand–silt mixtures with any amount of fines.     

Energy correction of dynamic cone penetration index for reliable evaluation of shear strength in frozen sand–silt mixtures

Acta Geotechnica - Previously, in situ tests have been conducted in cold regions since infrastructures such as pipelines have been actively built on frozen ground. However, the engineering...     

Shear strength and compressibility of oyster shell–sand mixtures

This paper investigates the fundamental characteristics of shear strength and deformation of crushed oyster shell–sand mixtures to stimulate recycling of waste oyster shells. Standard penetration tests (SPT) and large-scale direct-shear tests were carried out with different kinds of dry unit weight and mixing rate of oyster shell–sand mixture. Correlations between N-value, dry unit weight, and friction angle of mixtures were observed from the results of experimental tests, making it possible to estimate the in situ strength from SPT, and the coefficient of volume compressibility from the confined direct-shear compression test. These results also make it possible to compute the settlement of oyster shell–sand mixture when used in soft ground improvement.     

Swelling pressure–suction relationship of heavily compacted bentonite–sand mixtures

This paper presents results of an experimental work to determine a relationship between swelling pressure and suction of heavily compacted bentonite–sand mixtures. For comparison, tests were also carried out on heavily compacted bentonite specimens. A series of swelling pressure tests were performed using multi-step constant-volume method where suction of the specimens tested was reduced in a stepwise manner toward a zero value. The suction reduction was induced using vapor equilibrium and axis-translation techniques. It is shown that compacted specimens did not exhibit any collapse upon suction decrease and exhibited maximum swelling pressures at zero-equilibrium suction. The development of swelling pressure with decreasing suction of the specimens showed threshold suctions below which a further reduction in suction yields an increase in the swelling pressure of the same magnitude. The magnitude of threshold suction was found to be a function of bentonite content in compacted specimens.     

Effect of sand grain size and boundary condition on the swelling behavior of bentonite–sand mixtures

Deep geological repository is a favorable choice for the long-term disposal of nuclear wastes. Bentonite–sand mixtures have been proposed as the potential engineered barrier materials because of their suitable swelling properties and good ability to seal under hydrated repository conditions. To investigate the effects of sand grain size on the engineering performance of bentonite–sand mixtures, we prepare five types of bentonite–sand mixtures by mixing bentonite with sand of varying particle size ranges (0.075–0.25 mm, 0.25–0.5 mm, 0.5–1 mm, 1–2 mm and 2–5 mm, respectively). We carry out sequential oedometer tests under different simulated repository conditions, including constant vertical stress (CVS), constant stiffness (CS) and constant volume (CV) conditions. The microstructural heterogeneity and anisotropy of these soil mixtures are characterized through the quantitative analysis of micro-CT scanning results. Experimental results reveal that both sand grain size and boundary condition significantly influence the swelling of soil mixtures. Under three conditions, the temporal evolutions of swelling stress and strain follow similar trends that they increase faster at the beginning and gradually stabilize afterward. Comparing the ultimate values, swelling strains follow CVS?>?CS?>?CV, while swelling stresses follow CV?>?CS?>?CVS. Under CS boundary conditions, as the stiffness coefficient increases, the swelling pressure increases and the swelling strain decreases. CT results further indicate that mixtures with larger sand inclusions are more structurally heterogeneous and anisotropic, resulting in increased inter-particle friction and collision and a higher energy dissipation during the swelling process. Moreover, the non-uniform distribution of bentonite in local zones would be intensified, which plays an important role in compromising swelling behavior. Therefore, soil samples mixed with larger sand particles present a smaller swelling stress and strain values. This study may guide the choice of engineered barrier materials toward an improved design and assessment of geological repository facilities.

     

Effect of wetting–drying cycles on swelling behavior of lime stabilized sand–bentonite mixtures

In the present study, influence of wetting–drying cycles on swelling pressures of sand–bentonite mixtures used in the construction of sanitary landfills to have an impermeable liner was investigated before and after lime treatment of the mixtures. Swelling pressure tests were conducted to see if the swelling pressures were affected by wetting–drying cycles. First series of specimens were prepared as a mixture of sand and bentonite only. In the first series of specimens, sand was mixed with bentonite in various proportions with their optimum water contents and compacted by using standard proctor energy. In the second series of the specimens, lime in various proportions was added to the mixtures of sand–bentonite. Then, the sand–bentonite mixtures stabilized by lime were compacted with the standard proctor energy at their optimum moisture contents. Five wetting–drying cycles were performed on each specimen and values of swelling pressures were measured at the end of each cycle. Results of swelling pressure tests indicated that the swelling pressure is decreased when lime is added to the mixtures. In addition, decrements were observed on swelling pressures by wetting–drying cycles. The results of the experiments of this investigation showed that the beneficial effect of lime stabilization to control the swelling pressures was partly lost by the wetting–drying cycles. However, the test results indicated that the swelling pressures of the specimens made of sand–bentonite mixtures stabilized by lime were lower than the swelling pressures of the specimens made of only sand–bentonite mixtures.     

Microscale analysis to characterize effects of water content on the strength of cement-stabilized sand–clay mixtures

Acta Geotechnica - Cement stabilization is a useful and widely adopted method to improve the engineering properties of soils. However, characterization of the unconfined compressive strength, a...     

Impact of wetting–drying cycles on the hydraulic conductivity of liners made of lime-stabilized sand–bentonite mixtures for sanitary landfills

In this study, an investigation was performed to determine if lime-stabilized sand–bentonite mixtures are appropriate for the construction of sanitary landfills liners. For this aim, the hydraulic conductivity tests were conducted in the laboratory on sand–bentonite mixtures and lime-stabilized sand–bentonite mixtures to evaluate the effect of wetting–drying cycles. The hydraulic conductivity tests were performed to see if their hydraulic conductivities are affected by wetting–drying cycles. First series of specimens have been prepared as a mixture of sand and bentonite only. In the first series of specimens, sand was mixed with bentonite in proportions of 20, 30, 40, and 50 %. In the second series of the specimens, lime in proportions of 1, 2 and 3 % by weight was added to the mixtures of sand–bentonite in proportions of 20, 30, 40, and 50 %. From the results of the tests, it was observed that while optimum water content increased, maximum dry density decreased with addition of lime to the sand–bentonite mixtures. Generally, the hydraulic conductivity increased with the addition of lime to the mixtures but at low percentages of lime (1–2 %), however, slight decreases in k were recorded. It was also observed that the wetting–drying cycles on the permeability test indicate cure effect on specimens with addition of lime which resulted in decreased the hydraulic conductivity.     

Effect of microstructure on stress–strain and pore-pressure response of sabarmati sand under the influence of mica

ABSTRACT

Micaceous soil is believed to be detrimental for civil engineering constructions due to the effect of high compressibility, low compacted density and low shear strength. Individual mica particle has numerous intact mica flakes foliated over each other making it flexible upon loading and rebound upon unloading due to its low hardness and resilient nature. Hence, micaceous soils with mica content more than 10% are considered undesirable for highway pavements, embankments and railway track constructions. When platy mica particles are sufficiently numerous to interact with spherical sand particles, bridging and ordering phenomena are augmented within the soil mass creating unique sand-mica particle orientation (MS microstructure) unlike sand-sand particle orientation (PS microstructure). The current experimental research was conducted to evaluate the variation in stress–strain, pore pressure and effective stress path response of Sabarmati sand under the influence of mica (sand with 30% mica and pure sand) with MS and PS microstructure respectively. Effect of particle crushing on stress–strain and pore pressure response was also studied on Sabarmati sand with MS and PS microstructure. Distinctive macroscopic response was observed in Sabarmati sand with MS microstructure under the influence of mica as well as mica particle crushing.     

Equivalent granular state parameter and undrained behaviour of sand�Cfines mixtures

State parameter defined using void ratio, e, and the steady-state line has been shown to be effective in predicting the undrained behaviour of sand. However, steady-state line for sand with fines is dependent on fines content. To overcome this problem, the concept of equivalent granular void ratio, e*, has been well investigated. However, the conversion from e to e* has been essentially a back-analysis process. A methodology for converting e to e* without the need of a back-analysis process was first presented. The concept of equivalent granular state parameter, ψ*, defined in terms of e*, and equivalent granular steady-state line was then developed. An extensive experimental study was conducted to investigate whether ψ* can capture the effects of fines content, and thus can be used to correlate undrained behaviour of sand–fines mixtures without the need of separately considering the effects of fines content. This study suggested that the effective stress path and deviatoric stress–strain responses in undrained shearing can be correlated with the ψ* value at the start of undrained shearing irrespective of fines content.     

Modelling of fibre–cohesive soil mixtures

A new constitutive model for fibre-reinforced cohesive soil is proposed. The model combines a Cam-Clay like bounding surface model with an elastic–plastic one-dimensional fibrous element model. A “smearing procedure”, which can consider any spatial distribution of fibre orientation, is employed to transform discrete tensile forces developed in the fibres into stresses for the composite material. The fibre stress contribution is bounded by both degradation of soil–fibre bonding due to pull-out mechanism and tensile strength of the fibres. Eventual occurrence of fibre breakage is also considered. The model performances are analysed for both consolidation and shearing loading modes, and qualitative comparison is performed with experimental data available in the literature. For consolidation loading, tensile stresses are not developed in the fibres and thus the fibre effect is rather limited. For drained shear loading, addition of fibres can result in a consistent shear strength increase. The beneficial effect of fibres seems to be controlled by two parameters: the fibre tensile stiffness and the fibre/soil strain ratio that accounts for any possible slippage or shear deformation at the fibre/soil matrix interface. For undrained shear loading, the strengthening effect of the fibres appears to be counteracted by the increase in pore water pressure, induced by the additional confining contribution of the fibres. In agreement with published experimental data, the model suggests also that the moisture content is a key factor governing fibre effectiveness for undrained shearing. Finally, analysis of the model predicted critical states for fibre-reinforced cohesive soil is provided.     

Influence of dry density and water salinity on the swelling pressure and hydraulic conductivity of compacted GMZ01 bentonite–sand mixtures

Acta Geotechnica - Compacted Gaomiaozi bentonite–sand mixtures are regarded as attractive buffer/backfill materials for nuclear waste deep geological disposal. When the mixture blocks are...     

Swell–consolidation characteristics of artificial sand clay mixes

Many remedial measures have been devised to lessen the damage caused by expansive soils. Physical alteration, chemical stabilization, innovative foundation techniques like belled piers, drilled piers, under-reamed piles and granular pile anchors are some of these remedial measures. Mixing a non swelling material such as gravel or sand to expansive soil is one of the methods of physical alteration. This paper presents experimental data on artificially prepared sand-clay mixes. Swell and consolidation characteristics of these artificially prepared sand-clay mixes were studied in one dimensional consolidometer. Fine sand content and fines content in the expansive soil were arbitrarily varied in the investigation. The fines content was varied as 425–300 μm and 150–75 μm, separated from the same expansive soil based on the grain size. Swell potential and swelling pressure decreased with increasing fine sand content but increased with increasing fines content. Coefficient of compressibility, coefficient of volume compressibility and compression index of the samples decreased initially up to a sand content of 15% and thereafter increased at higher sand contents.     

Lateral soil–pipeline interaction in sand backfill: Effect of trench dimensions

Current analytical methodologies for the evaluation of soil pressures on laterally displaced pipelines, as in the case of differential (e.g. fault-induced) permanent ground movements, allow the use of sand fill material properties under the condition that the size of the trench is adequate so that the failure surface develops fully within the sand fill (i.e. “free field” response). The accuracy of this assumption is investigated in this paper by means of numerical analyses, which employ a number of advanced features, such as pipe-backfill interface elements, large strain formulation and mesh rezoning. Following verification against well-documented experimental data, the analyses investigate: (a) the shape and size of the failure mechanism, as well as, (b) the potential trench effects on soil pressures and pipeline strains in the case of a strike-slip fault rupture. It is shown that for small embedment depths soil failure extends to the ground surface, in the form of a general shear failure mechanism, while for larger depths it becomes progressively localized and surrounds the pipeline. It is also shown that, for most cases of pipeline diameter and embedment depth, common trench dimensions cannot contain the “free field” failure surface dimensions. Finally, analyses for limited trench dimensions, reveal that the ultimate soil pressure increases exponentially with decreasing trench width, leading to high bending strains in pipelines subjected to differential lateral ground displacements.     

Undrained Cyclic Pore Pressure Response of Sand–Silt Mixtures: Effect of Nonplastic Fines and Other Parameters

Literature regarding the pore pressure generation characteristics and in turn the cyclic resistance behaviour of silty sand deposits is confusing. In an attempt to clarify the effect of nonplastic fines on undrained cyclic pore pressure response of sand–silt mixtures, an experimental programme utilising around 289 stress-controlled cyclic triaxial tests on specimens of size 50 mm diameter and 100 mm height was carried out at a frequency of 0.1 Hz. Specimens were prepared to various measures of density through constant gross void ratio approach, constant relative density approach, constant sand skeleton void ratio approach, and constant interfine void ratio approach to study the effect of nonplastic fines on pore pressure response of sand–silt mixtures. The effect of relative density, confining pressure as well as the frequency and magnitude of cyclic loading was also studied. It was observed that the pore pressure response is greatly influenced by the limiting silt content and the relative density of a specimen corresponding to any approach. The influence of other parameters such as relative density, confining pressure and magnitude of cyclic loading was as usual but an increase in frequency of cyclic loading was seen to generate excess pore pressure at a higher rate indicating an impact load type of behaviour at higher frequency. Utilising the entire test results over a wide range of parameters a new pore pressure band for sand–silt mixtures in line with Lee and Albaisa (1974) has been proposed. Similarly another pore pressure band corresponding to 10th cycle of loading as suggested by Dobry (1985) and up to a shear strain of around 25% has been proposed. These two bands can readily be used by researchers and field engineers to readily assess the pore pressure response of sand–silt mixtures.     

Risk of water pollution due to ash–sludge mixtures: column trials

The purpose of this work was to study the risks of water pollution due to the use of mixtures containing wood ash and sewage sludge. Mixtures including sludge and ash may be recycled as fertilizers, and they are economical as they do not integrate commercial limes, but Escherichia coli counts may keep significantly high in such mixtures, because their pH is not alkaline enough. In view of that, it seems interesting to study the E. coli survival in lixiviate from ash?Csludge mixtures including limes rather than from ash?Csludge mixtures alone. Two kinds of experiments were performed using laboratory column trials under saturated flow conditions. The first experiment investigated the chemical leaching behaviour of a mixture of 70% timber-industry wood ashes and 30% urban sewage sludge (% dry weight) at doses equivalent to 10 and 30?Mg/ha. The second experiment studied the survival of E. coli in lixiviates generated from 30?Mg/ha of a mixture consisting in 75% wood ash, 20% sewage sludge and 5% quicklime (% dry weight). In the first experiment, admixture of the ash and sludge achieved a stabilization of elements such as aluminium, iron, magnesium, nickle, carbon monoxide, cadmium, chromium and molybdenum that reduced their solubility compared with that in the ash or sludge alone. Significant solubilisation of heavy metals was not observed, with overall minor risk of chemical water pollution. In the second experiment, although including quicklime E. coli counts were still detected in the lixiviate, indicating risk of water contamination.     

Rheological characteristics of mixed kaolin–sand slurry,impacts of pH,temperature, solid concentration and kaolin–sand mixing ratio

Significant amount of slurry waste is produced from mineral processing plants globally constituting high levels of both kaolin and sand in aqueous suspension. Large quantities of slurry and mine tailings require efficient handling, transportation and storage system. The transportation and treatment of kaolin–sand slurry is dependent on its rheological behaviour which is a function of temperature, total solid concentration and pH. In this study, the effects of total solid concentration, pH and temperature on rheological behaviour of kaolin–sand mixture were investigated. These parameters were varied to analyse the viscosity, yield stress, flow index and shear force requirements of the mixed kaolin–sand suspension as a function of these varying parameters. Experimental rheological investigation conducted on rotational stress-controlled rheometer equipped with Peltier concentric cylinder system showed that the kaolin–sand mixture suspension is shear thickening in nature. The shear stress-rate rheograms for the kaolin–sand suspension can be modelled by the Herschel–Bulkley model with high levels of accuracy for pH range of 4–11, temperature range of 20–50 °C and solid concentration of 5–50 %. Solid concentration of the suspension was found to significantly affect the rheological behaviour of the mixture where higher kaolin–sand slurry concentration resulted in greater viscosity and the trend becoming less predictable for solid concentration greater than 50 % by weight. pH was another factor affecting the rheological behaviour of kaolin–sand slurry. pH of 3 or less resulted in the dramatic increase of viscosity of the suspension possibly due to the isoelectric point of the mixture system found between pH of 3 and 4.