Measuring streambank erosion due to ground water seepage: correlation to bank pore water pressure,precipitation and stream stage

Limited information exists on one of the mechanisms governing sediment input to streams: streambank erosion by ground water seepage. The objective of this research was to demonstrate the importance of streambank composition and stratigraphy in controlling seepage flow and to quantify correlation of seepage flow/erosion with precipitation, stream stage and soil pore water pressure. The streambank site was located in Northern Mississippi in the Goodwin Creek watershed. Soil samples from layers on the streambank face suggested less than an order of magnitude difference in vertical hydraulic conductivity (K_s) with depth, but differences between lateral K_s of a concretion layer and the vertical K_s of the underlying layers contributed to the propensity for lateral flow. Goodwin Creek seeps were not similar to other seeps reported in the literature, in that eroded sediment originated from layers underneath the primary seepage layer. Subsurface flow and sediment load, quantified using 50 cm wide collection pans, were dependent on the type of seep: intermittent low‐flow (LF) seeps (flow rates typically less than 0·05 L min^?1), persistent high‐flow (HF) seeps (average flow rate of 0·39 L min^?1) and buried seeps, which eroded unconsolidated bank material from previous bank failures. The timing of LF seeps correlated to river stage and precipitation. The HF seeps at Goodwin Creek began after rainfall events resulted in the adjacent streambank reaching near saturation (i.e. soil pore water pressures greater than ?5 kPa). Seep discharge from HF seeps reached a maximum of 1·0 L min^?1 and sediment concentrations commonly approached 100 g L^?1. Buried seeps were intermittent but exhibited the most significant erosion rates (738 g min^?1) and sediment concentrations (989 g L^?1). In cases where perched water table conditions exist and persistent HF seeps occur, seepage erosion and bank collapse of streambank sediment may be significant. Copyright © 2007 John Wiley & Sons, Ltd.     

Production of radionuclides by cosmic rays at mountain altitudes

Production rates of²²Na (T_1/2 = 2.6years) from aluminium by the action of cosmic rays are measured at the Mont Blanc (altitude 4600 m), the Aiguille du Midi (3840 m), and the Col du Lautaret (2070 m). They are2.3 ± 0.5,1.8 ± 0.3,and0.77 ± 0.18 atoms min^?1 kg^?1, respectively, in good agreement with the calculated production rates, 2.4, 1.7 and 0.6 atoms min^?1 kg^?1, respectively, at the three stations.Production rates of²⁴Na (T_1/2 = 15hours) from aluminium and magnesium are also measured at the Aiguille du Midi; the observed rates of3.4 ± 0.4and6.0 ± 1.7 atoms min^?1 kg^?1, respectively, agree well with the theoretically expected rates of 3.7 and 5.6 atoms min^?1 kg^?1.The production rates of³H,⁷Be,¹⁰Be,¹⁴C,²²Na,²⁶Al,³⁶Cl,³⁷Ar,³⁹Ar,⁵³Mn,⁵⁴Mn, and⁵⁵Fe in terrestrial rocks by the action of cosmic rays are calculated in order to show the possibility of applying the measurements of these cosmogenic radionuclides to the earth science.     

Processes controlling rapid temperature variations on rock surfaces

In arid environments, thermal oscillations are an important source of rock weathering. Measurements of temperature have been made on the surface of rocks in a desert environment at a sampling interval of 0·375 s, with simultaneous measurements of wind speed, air temperature, and incoming shortwave radiation. Over timescales of hours, the temperature of the rock surface was determined primarily by shortwave radiation and air temperature, while rapid temperature variations, high dT/dt, at intervals of seconds or less, were determined by wind speed. The maximum values of temperature change and time spent above 2°C min^?1 increased at high measurement rates and were much higher than previously reported. The maximum recorded value of dT/dt was 137°C min^?1 and the average percentage time spent above 2°C min^?1 was ～70 ± 13%. Maximum values of dT/dt did not correlate with the maximum values of time spent above 2°C min^?1. Simultaneous measurements of two thermocouples 5·5 cm apart on a single rock surface had similar temperature and dT/dt values, but were not correlated at sampling intervals of less than 10 s. It is suggested that this is resulting from rapid fluctuations due to small spatial and timescale wind effects that are averaged out when data is taken at longer sampling intervals, ～10 s or greater. Published in 2010 by John Wiley & Sons, Ltd.     

Effects of the introduction of rice on evapotranspiration in seasonal wetlands

Land use changes in wetland areas can alter evapotranspiration, a major component of the water balance, which eventually affects the water cycle and ecosystem. This study assessed the effect of introduced rice‐cropping on evapotranspiration in seasonal wetlands of northern Namibia. By using the Bowen ratio–energy balance method, measurements of evapotranspiration were performed over a period of 2.5 years at two wetland sites—a rice field (RF) and a natural vegetation field (NVF)—and at one upland field (UF) devoid of surface water. The mean evapotranspiration rates of RF (1.9 mm daytime^?1) and NVF (1.8 mm daytime^?1) were greater than that in UF (1.0 mm daytime^?1). RF and NVF showed a slight difference in seasonal variations in evapotranspiration rates. During the dry season, RF evapotranspiration was less than the NVF evapotranspiration. The net radiation in RF was less in this period because of the higher albedo of the non‐vegetated surface after rice harvesting. In the early growth period of rice during the wet season, evapotranspiration in RF was higher than that in NVF, which was attributed to a difference in the evaporation efficiency and the transfer coefficient for latent heat that were both affected by leaf area index (LAI). Evapotranspiration sharply negatively responded to an increase in LAI when surface water is present according to sensitivity analysis, probably because a higher LAI over a surface suppresses evaporation. The control of LAI is therefore a key for reducing evaporation and conserving water. Copyright © 2013 John Wiley & Sons, Ltd.     

Comparison of methods for quantifying surface sublimation over seasonally snow‐covered terrain

Snow sublimation can be an important component of the snow‐cover mass balance, and there is considerable interest in quantifying the role of this process within the water and energy balance of snow‐covered regions. In recent years, robust eddy covariance (EC) instrumentation has been used to quantify snow sublimation over snow‐covered surfaces in complex mountainous terrain. However, EC can be challenging for monitoring turbulent fluxes in snow‐covered environments because of intensive data, power, and fetch requirements, and alternative methods of estimating snow sublimation are often relied upon. To evaluate the relative merits of methods for quantifying surface sublimation, fluxes calculated by the EC, Bowen ratio–energy balance (BR), bulk aerodynamic flux (BF), and aerodynamic profile (AP) methods and their associated uncertainty were compared at two forested openings in the Colorado Rocky Mountains. Biases between methods are evaluated over a range of environmental conditions, and limitations of each method are discussed. Mean surface sublimation rates from both sites ranged from 0.33 to 0.36 mm day^?1, 0.14 to 0.37 mm day^?1, 0.10 to 0.17 mm day^?1, and 0.03 to 0.10 mm day^?1 for the EC, BR, BF and AP methods, respectively. The EC and/or BF methods are concluded to be superior for estimating surface sublimation in snow‐covered forested openings. The surface sublimation rates quantified in this study are generally smaller in magnitude compared with previously published studies in this region and help to refine sublimation estimates for forested openings in the Colorado Rocky Mountains. Copyright © 2016 John Wiley & Sons, Ltd.     

Characterizing infiltration and internal drainage of South African dryland soils

Surface infiltration and internal drainage properties of five soil types from arid drylands of South Africa were studied under double ring infiltrometer, rainfall simulation plots (1 m²) and instantaneous drainage plots (9 m²). Changes in soil water content during 40 minute rainfall simulation for a rainstorm with average intensity of 1.61 mm min^?1 and 30 day drainage period were measured at various depths by 1.5 m long capacitance soil water measuring (DFM) probe. Different (P < 0.05) mean surface steady infiltration rate ranged from 0.05 to 4.47 mm min^?1 and had a negative power relationship (R ² = 0.65) with horizon clay plus fine silt content. Power regression (R ² ≥ 86%) described rainstorm infiltration and obtained steady rates within an average time of 15 minutes. Mean total infiltrated soil water content was lowest (P < 0.05) from surface horizons with either 47.7% clay plus fine silt content or bulk density of 1.91 g cm^?3 and exchangeable sodium of not less than 44 mg kg^?1. Surface horizons with lower surface bulk density and total sand fraction of more than 72% had infiltrated depth and mean total infiltrated soil water content up to 40 cm deeper and 0.55 mm mm^?1 greater, respectively. Drainage rate at drained upper limit calculated from the Wilcox drainage model (R ² ≤ 0.97%) was 0.2 mm day^?1 or less were from underlying horizons with either clay plus fine silt of 45% or soft calcium carbonate. Higher drainage rate with accumulative drainage amount greater than 60 mm were from soil profile horizons with clay plus fine silt content of less than 20% and above unity steady infiltration rates. Rainstorm infiltration and drainage rates was shown to depend on permeability and coarseness of the respective soil surface and subsurface horizons; a phenomenon critical for harnessing rain and flood water to recharge groundwater. Copyright © 2016 John Wiley & Sons, Ltd.     

Dynamic simulation on hydraulic characteristic values of overland flow

The economic forest management is one of the main land use models on low hill gentle slope. In order to investigate the soil erosion properties of bare slope under economic forest, dynamic simulation on hydraulic characteristic values of overland flow was carried out under 0.5 mm min^?1, 1.2 mm min^?1 and 1.8 mm min^?1 rainfall intensities. Results indicated that runoff shear stress increased with increasing of slope length and their relationship can be described by quadratic equation. There were abnormal points at the length of 4 m and 5.5 m under rainfall intensity of 1.8 mm min^?1. The shallow flow was pseudo-laminar flow under 0.5 mm min^?1, 1.2 mm min^?1 and 1.8 mm min^?1 rainfall intensities, and the runoff at upslope was sluggish flow then changed to torrential flow at downslope with increasing of slope length. Critical Reynolds number varied from sluggish flow to torrential flow with 1.8 mm min^?1 rainfall intensity and was more than that under 0.5 mm min^?1. Reynolds number can be estimated by power function of slope length. And there was a positive correlation between runoff shear stress and both Froude number Fr and Reynolds number Re. We hope this study can provide scientific gist for soil erosion control under economic forest.     

PUBLICATIONS DE L'ASSOCIATION INTERNATIONALE DES SCIENCES HYDROLOGIQUES

ABSTRACT

The evaporation losses from the container of an old galvanized Hellmann gauge, 7·1 cm² aperture area, were five times greater than the losses from the container of a new gauge, 1·8 cm² aperture area, of almost the same grey colour. The maximum evaporation from the old gauge amounted to 0·75 mm per day. The same evaporation losses in the Baye of Montreux basin over a period of 10 years from April to September amounted to 0·09 mm per measurement or to 0·7 per cent of the precipitation catch. There is a relationship between the monthly percentage evaporation losses and the ratio of evaporation time and rainfall duration (r = 0·803).     

Erosion rates in the southern oregon coast range: Evidence for an equilibrium between hillslope erosion and sediment yield

The relationship of hillslope erosion rates and sediment yield is often poorly defined because of short periods of measurement and inherent spatial and temporal variability in erosion processes. In landscapes containing hillslopes crenulated by alternating topographic noses and hollows, estimates of local hillslope erosion rates averaged over long time periods can be obtained by analysing colluvial deposits in the hollows. Hollows act as local traps for a portion of the colluvium transported down hillslopes, and erosion rates can be calculated using the age and size of the deposits and the size of the contributing source area. Analysis of colluvial deposits in nine Oregon Coast Range hollows has yielded average colluvial transport rates into the hollows of about 35cm³cm^?1yr^?1 and average bedrock lowering rates of about 0.07 mm yr^?1 for the last 4000 to 15000 yr. These rates are consistent with maximum bedrock exfoliation rates of about 0.09 mm yr^?1 calculated from six of the hollows, supporting the interpretation that exfoliation rates limit erosion rates on these slopes. Sediment yield measurements from nine Coast Range streams provide similar basin-wide denudation rates of between 0.05 and 0.08mm yr^?1, suggesting an approximate steady-state between sediment production on hillslopes and sediment yield. In addition, modern sediment yields are similar in basins varying in size from 1 to 1500 km², suggesting that erosion rates are spatially uniform and providing additional evidence for an approximate equilibrium in the landscape.     

Seasonal patterns of suspended sediment load and erosion-transport assessment in a Mediterranean basin

ABSTRACT

To assess seasonal patterns of suspended sediment load and its erosion–transport interactions, 17 years of river monitoring data from the Isser River Basin (northwest Algeria) were studied, considering continuous and event-scale approaches. The results show significant differences in sediment yield and transport processes between dry and wet periods. A rate of 8 t ha^?1 year^?1 was estimated from continuous analysis, with values of 4.3 and 13 t ha^?1 year^?1 for wet and dry periods, respectively. Estimates of soil delivery ratio pointed to higher values during dry periods and the dominance of hillslope erosion processes. At the event scale, the hysteresis loops confirmed these seasonal patterns in transport dynamics. The calibration of the MUSLE model highlighted the severity of rainfall during the dry period. These results emphasize the importance of seasonality in erosion and transport processes with special relevance in terms of climate change predictions.     

Infiltration-excess caused by Stemflow in a cyclone-prone tropical rainforest

Tropical rainforest canopy trees that have large projected areas of upwardly inclined branches are capable of funnelling large volumes of rainwater down their trunks. During periods of prolonged heavy rainfall on Mount Bellenden Ker in northeast Queensland, Australia, stemflow volumes were found to be as much as two orders of magnitude greater than the volume of incident rainfall expected in a rain gauge occupying an area equal to the trunk basal area. Stemflow totals ranging from 6000 to 70000 litres were generated by individual trees from 7800 mm of rainfall over two successive wet seasons. The combination of high intensity rainfall and the funnelling effect results in significant quantities of infiltration-excess at the ground surface. Stemflow fluxes as high as 31.4 cm³ min^?1 per cm² of basal area (i.e. the equivalent of 314 mm min^?1) were recorded when rainfall intensity was only 2 mm min^?1. The mean infiltration capacity of the topsoil was determined to be 6.2 mm min^?1. The areas over which the stemflow would have had to spread in order to infiltrate were computed to be as much as 3 m² around the bases of individual canopy trees. Approximations of the distances that the infiltration-excess would have travelled away from the tree bases were calculated by assuming that the infiltration area either expands radially outward in the form of an annulus or extends straight downslope from the tree base.     

It goes both ways: measurements of simultaneous evapotranspiration and fog droplet deposition at a montane cloud forest

Fluxes of latent heat, sensible heat, and water vapor, including turbulent deposition of fog droplets, were measured for two months in autumn 2005 within a subtropical montane cypress forest in Taiwan. The goal of the study was to determine whether significant evapotranspiration can occur during foggy conditions. Water vapor fluxes, Q_W, as determined with the Bowen Ratio method, were compared to those simultaneously measured with the eddy covariance method. The median Bowen Ratio was 1.06, and the median Q_W flux was 5 · 2 × 10^?5 kg m^?2 s^?1. The vertical gradients of temperature and specific humidity over the forest, ΔT and Δq, peaked around noon during days without fog, and were reduced during foggy conditions. For 66% of the data points, ΔT and Δq were negative, corresponding to positive (upward) fluxes of sensible heat Q_H and latent heat Q_E. A Monte Carlo simulation proved that statistically significant evapotranspiration rates, i.e., upward water vapor fluxes, occurred during fog. At the same time, deposition fluxes of fog droplets occurred. Our results show that even during fog events, significant evapotranspiration may occur. Copyright © 2008 John Wiley & Sons, Ltd.     

The increase of rainfall erosivity and initial soil erosion processes due to rainfall acidification

The drastic growth of population in highly industrialized urban areas, as well as fossil fuel use, is increasing levels of airborne pollutants and enhancing acid rain. In rapidly developing countries such as Iran, the occurrence of acid rain has also increased. Acid rain is a driving factor of erosion due to the destructive effects on biota and aggregate stability; however, little is known about its impact on specific rates of erosion at the pedon scale. Thus, the present study aimed to investigate the effect of acid rain at pH levels of 5.25, 4.25, and 3.75 for rainfall intensities of 40, 60, and 80 mm h^?1 on initial soil erosion processes under dry and saturated soil conditions using rainfall simulations. The results were compared using a two‐way ANOVA and Duncan tests and showed that initial soil erosion rates with acidic rain and non‐acidic rain under dry soil conditions were significantly different. The highest levels of soil particle loss due to splash effects in all rainfall intensities were observed with the most acidic rain (pH = 3.75), reaching maximum values of 16 g m^?2 min^?1. The lowest levels of particle losses were observed in the control plot where non‐acidic rain was used, with values ranging from 3.8 to 8.1 g m^?2 min^?1. Similarly, under saturated soil conditions, the lowest level of soil particle loss was observed in the control plot, and the highest peaks of soil loss were observed for the most acidic rains (pH = 3.75 and pH = 4.25), reaching maximum average values of 40 g m^?2 min^?1. However, for saturated soils with acidic water but with non‐acidic rain, the highest soil particle loss was observed for the control plot for all the rainfall intensities. In conclusion, acidic rain has a negative impact on soils, which can be more intense with a concomitant increase in rainfall intensity. Rapid solutions, therefore, need to be found to reduce the emission of pollutants into the air, otherwise, rainfall erosivity may drastically increase.     

Leakage properties of the multi-aquifer system underlying the Greater Onitsha water scheme borehole field,Anambra State,Nigeria

Abstract

Leakage properties and the potential for land subsidence due to groundwater withdrawal from a multi-aquifer water supply system were investigated by applying leaky type curve and one dimensional consolidation models to drawdown data that were obtained during a pumping test experiment in an aquifer-aquitard system. The producing aquifer has transmissivity and storativity values of 5.3 × 10^?3 m² s^?1 and 9.54 × 10^?4 respectively. It is recharged through leakage at a rate of 5.67 × 10^?8 m s^?1, giving a leakage amount of more than 0.007 m³ s^?1. Drainage of the aquifer-aquitard system could result in aquitard compaction of between 50 and 180 mm year^?1 for pumping periods of 6 and 22 h day^?1, respectively. The observed leakage has important implications for land subsidence problems and waste disposal practices in the area.     

Measuring effectiveness of three postfire hillslope erosion barrier treatments,western Montana,USA

After the Valley Complex Fire burned 86 000 ha in western Montana in 2000, two studies were conducted to determine the effectiveness of contour‐felled log, straw wattle, and hand‐dug contour trench erosion barriers in mitigating postfire runoff and erosion. Sixteen plots were located across a steep, severely burned slope, with a single barrier installed in 12 plots (four per treatment) and four plots left untreated as controls. In a rainfall‐plus‐inflow simulation, 26 mm h^?1 rainfall was applied to each plot for 1 h and 48 L min^?1 of overland flow was added for the last 15 min. Total runoff from the contour‐felled log (0·58 mm) and straw wattle (0·40 mm) plots was significantly less than from the control plots (2·0 mm), but the contour trench plots (1·3 mm) showed no difference. The total sediment yield from the straw wattle plots (0·21 Mg ha^?1) was significantly less than the control plots (2·2 Mg ha^?1); the sediment yields in the contour‐felled log plots (0·58 Mg ha^?1) and the contour trench plots (2·5 Mg ha^?1) were not significantly different. After the simulations, sediment fences were installed to trap sediment eroded by natural rainfall. During the subsequent 3 years, sediment yields from individual events increased significantly with increasing 10 min maximum intensity and rainfall amounts. High‐intensity rainfall occurred early in the study and the erosion barriers were filled with sediment. There were no significant differences in event or annual sediment yields among treated and control plots. In 2001, the overall mean annual sediment yield was 21 Mg ha^?1; this value declined significantly to 0·6 Mg ha^?1 in 2002 and 0·2 Mg ha^?1 in 2003. The erosion barrier sediment storage used was less than the total available storage capacity; runoff and sediment were observed going over the top and around the ends of the barriers even when the barriers were less than half filled. Published in 2007 by John Wiley & Sons, Ltd.     

Seasonal variation in the energy and water exchanges above and below a larch forest in eastern Siberia

The water and energy exchanges in forests form one of the most important hydro‐meteorological systems. There have been far fewer investigations of the water and heat exchange in high latitude forests than of those in warm, humid regions. There have been few observations of this system in Siberia for an entire growing season, including the snowmelt and leaf‐fall seasons. In this study, the characteristics of the energy and water budgets in an eastern Siberian larch forest were investigated from the snowmelt season to the leaf‐fall season. The latent heat flux was strongly affected by the transpiration activity of the larch trees and increased quickly as the larch stand began to foliate. The sensible heat dropped at that time, although the net all‐wave radiation increased. Consequently, the seasonal variation in the Bowen ratio was clearly ‘U’‐shaped, and the minimum value (1·0) occurred in June and July. The Bowen ratio was very high (10–25) in early spring, just before leaf opening. The canopy resistance for a big leaf model far exceeded the aerodynamic resistance and fluctuated over a much wider range. The canopy resistance was strongly restricted by the saturation deficit, and its minimum value was 100 s m^?1 (10 mm s^?1 in conductance). This minimum canopy resistance is higher than values obtained for forests in warm, humid regions, but is similar to those measured in other boreal conifer forests. It has been suggested that the senescence of leaves also affects the canopy resistance, which was higher in the leaf‐fall season than in the foliated season. The mean evapotranspiration rate from 21 April 1998 to 7 September 1998 was 1·16 mm day^?1, and the maximum rate, 2·9 mm day^?1, occurred at the beginning of July. For the growing season from 1 June to 31 August, this rate was 1·5 mm day^?1. The total evapotranspiration from the forest (151 mm) exceeded the amount of precipitation (106 mm) and was equal to 73% of the total water input (211 mm), including the snow water equivalent. The understory evapotranspiration reached 35% of the total evapotranspiration, and the interception evaporation was 15% of the gross precipitation. The understory evapotranspiration was high and the interception evaporation was low because the canopy was sparse and the leaf area index was low. Copyright © 2001 John Wiley & Sons, Ltd.     

An evaluation of sediment rating curves for estimating suspended sediment concentrations for subsequent flux calculations

In the absence of actual suspended sediment concentration (SSC) measurements, hydrologists have used sediment rating (sediment transport) curves to estimate (predict) SSCs for subsequent flux calculations. Various evaluations of the sediment rating‐curve method were made using data from long‐term, daily sediment‐measuring sites within large (>1 000 000 km²), medium (<1 000 000 to >1000 km²), and small (<1000 km²) river basins in the USA and Europe relative to the estimation of suspended sediment fluxes. The evaluations address such issues as the accuracy of flux estimations for various levels of temporal resolution as well as the impact of sampling frequency on the magnitude of flux estimation errors. The sediment rating‐curve method tends to underpredict high, and overpredict low SSCs. As such, the range of errors associated with concomitant flux estimates for relatively short time‐frames (e.g. daily, weekly) are likely to be substantially larger than those associated with longer time‐frames (e.g. quarterly, annually) because the over‐ and underpredictions do not have sufficient time to balance each other. Hence, when error limits must be kept under ±20%, temporal resolution probably should be limited to quarterly or greater. The evaluations indicate that over periods of 20 or more years, errors of <1% can be achieved using a single sediment rating curve based on data spanning the entire period. However, somewhat better estimates for the entire period, and markedly better annual estimates within the period, can be obtained if individual annual sediment rating curves are used instead. Relatively accurate (errors <±20%) annual suspended sediment fluxes can be obtained from hydrologically based monthly measurements/samples. For 5‐year periods or longer, similar results can be obtained from measurements/samples collected once every 2 months. In either case, hydrologically based sampling, as opposed to calendar‐based sampling is likely to limit the magnitude of flux estimation errors. Published in 2003 John Wiley & Sons, Ltd.     

Surfactant Enhance DLLME/FO‐LADS: Assay of Malachite Green Level in Aquatic Environment of Trout Fish

Malachite green (MG), a traditional agent used in aquaculture although is not approved; its low cost and high efficacy make illicit use likely. We developed a small‐scale, simple, and sensitive dispersive liquid–liquid microextraction procedure for the assay of trace amounts of MG in aquatic environment of Trout fish. Fiber optic‐linear array detection spectrophotometry with charge‐coupled device detector benefiting from a microcell was used for this purpose. The method is based on enhancement effect of an anionic surfactant on the extraction of MG in to very fine multidroplets of microextraction solvent which made assisted by disperser solvent. Under the optimum conditions, the enrichment factor 77.5 was obtained from a 5‐mL water sample. The calibration graph was linear up to 5 × 10^?7 mol L^?1 with detection limit of 1 × 10^?8 mol L^?1. The relative standard deviation for seven replicate measurements of 4 × 10^?7 and 5 × 10^?8 mol L^?1 of MG were 3.3 and 4.5%, respectively.     

Bioaugmentation and Propane Biosparging for In Situ Biodegradation of 1,4‐Dioxane

Propane biosparging and bioaugmentation were applied to promote in situ biodegradation of 1,4‐dioxane at Site 24, Vandenberg Air Force Base (VAFB), CA. Laboratory microcosm and enrichment culture testing demonstrated that although native propanotrophs appeared abundant in the shallow water‐bearing unit of the aquifer (8 to 23 ft below ground surface [bgs]), they were difficult to be enriched from a deeper water‐bearing unit (82 to 90 feet bgs). Bioaugmentation with the propanotroph Rhodococcus ruber ENV425, however, supported 1,4‐dioxane biodegradation in microcosms constructed with samples from the deep aquifer. For field testing, a propane‐biosparging system consisting of a single sparging well and four performance monitoring wells was constructed in the deep aquifer. 1,4‐dioxane biodegradation began immediately after bioaugmentation with R. ruber ENV425 (36 L; 4 × 10⁹ cells/mL), and apparent first‐order decay rates for 1,4‐dioxane ranged from 0.021 day^?1 to 0.036 day^?1. First‐order propane consumption rates increased from 0.01 to 0.05 min^?1 during treatment. 1,4‐dioxane concentrations in the sparging well and two of the performance monitoring wells were reduced from as high as 1090 µg/L to <2 µg/L, while 1,4‐dioxane concentration was reduced from 135 µg/L to 7.3 µg/L in a more distal third monitoring well. No 1,4‐dioxane degradation was observed in the intermediate aquifer control well even though propane and oxygen were present. The demonstration showed that propane biosparging and bioaugmentation can be used for in situ treatment of 1,4‐dioxane to regulatory levels.     

Extra-terrestrial 53Mn in Antarctic ice

The reasons why⁵³Mn (a cosmogenic radionuclide with a half-life of 3.7 × 10⁶ y) appears as one of the best indicators of the presence of interplanetary dust are summarized. This paper reports the detection of⁵³Mn in pre-1952 snow samples collected on the Eastern Antarctic Plateau in the vicinity of Plateau Station. The measurements were carried out by neutron activation and X-ray spectrometry on three samples weighing a few hundred kg and covering each the time interval 1935–1950. The specific activity of⁵³Mn was found to be (0.82 ± 0.17) disint.min^?1/10³ tons of snow, corresponding to a deposition rate at Plateau Station of (2.2 ± 0.5) × 10^?5 disint. min^?1 m^?2 y^?1. The mean global deposition rate would be three times higher if⁵³Mn were assumed to behave in the same way as stratospheric⁹⁰Sr. By comparing this figure with existing data on the meteorite flux reaching the earth and with the galactic and solar production rates of⁵³Mn, it is concluded that the bulk of the⁵³Mn found at Plateau Station is associated with interplanetary dust in which it had been produced by the action of solar protons on iron. The deposition rate of extra-terrestrial dust-borne iron must be between 1.3 × 10^?5 and 1.3 × 10^?4 g m^?2 y^?1 at Plateau Station. These results support jointly with other studies the concept of an interplanetary zodiacal cloud of dust with a chemical composition and density not essentially different from chondritic meteorites, with a relatively ‘flat’ grain size distribution and a mass influx to the earth of the order of 10⁵ tons/y.