Evidence that piezometers vent gas from peat soils and implications for pore‐water pressure and hydraulic conductivity measurements

Entrapped gas bubbles in peat can alter the buoyancy, storativity, void ratio and expansion/contraction properties of the peat. Moreover, when gas bubbles block water‐conducting pores they can significantly reduce saturated hydraulic conductivity and create zones of over‐pressuring, perhaps leading to an alteration in the magnitude and direction of groundwater flow and solute transport. Some previous researches have demonstrated that these zones of over‐pressuring are not observed by the measurements of pore‐water pressures using open‐pipe piezometers in peat; rather, they are only observed with pressure transducers sealed in the peat. In has been hypothesized that open‐pipe piezometers vent entrapped CH₄ to the atmosphere and thereby do not permit the natural development of zones of entrapped gas. Here we present findings of the study to investigate whether piezometers vent subsurface CH₄ to the atmosphere and whether the presence of piezometers alters the subsurface concentration of dissolved CH₄. We measured the flux of methane venting from the piezometers and also determined changes in pore‐water CH₄ concentration at a rich fen in southern Ontario and a poor fen in southern Quebec, in the summer of 2004. Seasonally averaged CH₄ flux from piezometers was 1450 and 37·8‐mg CH₄ m^?2 d^?1 at the southern Ontario site and Quebec site, respectively. The flux at the Ontario site was two orders of magnitude greater than the diffusive flux at the site. CH₄ pore‐water concentrations were significantly lower in open piezometers than in water taken from sealed samplers at both the Ontario and Quebec sites. The flux of CH₄ from piezometers decreased throughout the season suggesting that CH₄ venting through the piezometer exceeded the rate of methanogenesis in the peat. Consequently we conclude that piezometers may alter the gas dynamics of some peatlands. We suggest that less‐invasive techniques (e.g. buried pressure transducers, tracer experiments) are needed for the accurate measurement of pore‐water pressures and hydraulic conductivity in peatlands with a large entrapped gas component. Furthermore, we argue that caution must be made in interpreting results from previous peatland hydrology studies that use these traditional methods. Copyright © 2009 John Wiley & Sons, Ltd.     

Conducting Slug Tests in Mini‐Piezometers

Slug tests performed using mini‐piezometers with internal diameters as small as 0.43 cm can provide a cost effective tool for hydraulic characterization. We evaluated the hydraulic properties of the apparatus in a laboratory environment and compared those results with field tests of mini‐piezometers installed into locations with varying hydraulic properties. Based on our evaluation, slug tests conducted in mini‐piezometers using the fabrication and installation approach described here are effective within formations where the hydraulic conductivity is less than 1 × 10^?3 cm/s. While these constraints limit the potential application of this method, the benefits to this approach are that the installation, measurement, and analysis is cost effective, and the installation can be completed in areas where other (larger diameter) methods might not be possible. Additionally, this methodology could be applied to existing mini‐piezometers previously installed for other purposes. Such analysis of existing installations could be beneficial in interpreting previously collected data (e.g., water‐quality data or hydraulic head data).     

Hydraulic parameters of a multilayered aquifer system in Kuwait City

The Kuwait Group consists mainly of clastic sediments overlying unconformably the Dammam Formation of Tertiary age. The Kuwait Group is generally divided into three main hydrostratigraphic units: the upper and lower aquifers separated by an aquitard. The upper aquifer is further divided into the water table aquifer, an aquitard and a semiconfined aquifer. This semiconfined unit was pumped and the drawdowns were observed in piezometers screened in various subunits of the Kuwait Group. Some pumping tests of short duration were carried out in the top water table aquifer as well. These tests showed that the subunits of the Kuwait Group are hydraulically interconnected to a varying degree.

The pumping test data were analysed using conventional analytical solutions. The semiconfined pumping test was also simulated by a quasi-three-dimensional model using a leaky multiaquifer modelling technique. The initial hydraulic parameters were improved manually in the model till best fit drawdowns were obtained.

The final parameters obtained by simulation of the pumping tests were used in designing a pilot drainage system for the control of a rising groundwater table in parts of Kuwait City.     

Determination of specific yield for the Biscayne Aquifer with a canal-drawdown test

Data from a large-scale canal-drawdown test were used to estimate the specific yield (sy) of the Biscayne Aquifer, an unconfined limestone aquifer in southeast Florida. The drawdown test involved dropping the water level in a canal by about 30 cm and monitoring the response of hydraulic head in the surrounding aquifer. Specific yield was determined by analyzing data from the unsteady portion of the drawdown test using an analytical stream-aquifer interaction model (Zlotnik and Huang 1999). Specific yield values computed from drawdown at individual piezometers ranged from 0.050 to 0.57, most likely indicating heterogeneity of specific yield within the aquifer (small-scale variation in hydraulic conductivity may also have contributed to the differences in sy among piezometers). A value of 0.15 (our best estimate) was computed based on all drawdown data from all piezometers. We incorporated our best estimate of specific yield into a large-scale two-dimensional numerical MODFLOW-based ground water flow model and made predictions of head during a 183-day period at four wells located 337 to 2546 m from the canal. We found good agreement between observed and predicted heads, indicating our estimate of specific yield is representative of the large portion of the Biscayne Aquifer studied here. This work represents a practical and novel approach to the determination of a key hydrogeological parameter (the storage parameter needed for simulation and calculation of transient unconfined ground water flow), at a large spatial scale (a common scale for water resource modeling), for a highly transmissive limestone aquifer (in which execution of a traditional pump test would be impractical and would likely yield ambiguous results). Accurate estimates of specific yield and other hydrogeological parameters are critical for management of water supply, Everglades environmental restoration, flood control, and other issues related to the ground water hydrology of the Biscayne Aquifer.     

TABLE DES MATIÈRES DU BULLETIN DE 1956 A 1960 / CONTENTS OF THE BULLETIN 1956–1960

Abstract

Piezometers and wells installed for water quality monitoring are frequently used to assess the saturated hydraulic conductivity (K) in the surrounding formation. A series of recovery tests was conducted to evaluate how purging, required to obtain representative water quality samples, affected measured values of hydraulic conductivity in 15 newly installed and undeveloped piezometers placed to between 2 and 15 m depth (in oxidized and unoxidized material) in a loamy glacial till (K range from 10^?6 to 10^?9 m s^?1). Piezometers were purged between 9 and 11 times for sampling over a period of five months. The effect of the purgings on piezometer development was evaluated by changes in slope of the water level recovery curves which were used to calculate hydraulic conductivity. The first five purgings following piezometer installation increased K in the 15 piezometers by an average of 34%. The average increase in a value of K after 10 purgings was 44%. Values measured for hydraulic conductivity in a 75 mm diameter auger hole appeared stable after four purgings but piezometers installed in larger diameter boreholes (100 mm to 280 mm) snowed increases in K with up to 10 purgings. The hydraulic conductivity determined for piezometers installed at a 30° angle to the vertical showed greater variability than was observed in the adjacent vertically installed piezometers at the same depth.     

Analysis of a vertical dipole tracer test in highly fractured rock

The results of a vertical dipole tracer experiment performed in highly fractured rocks of the Clare Valley, South Australia, are presented. The injection and withdrawal piezometers were both screened over 3 m and were separated by 6 m (midpoint to midpoint). Due to the long screen length, several fracture sets were intersected, some of which do not connect the two piezometers. Dissolved helium and bromide were injected into the dipole flow field for 75 minutes, followed by an additional 510 minutes of flushing. The breakthrough of helium was retarded relative to bromide, as was expected due to the greater aqueous diffusion coefficient of helium. Also, only -25% of the total mass injected of both tracers was recovered. Modeling of the tracer transport was accomplished using an analytical one-dimensional flow and transport model for flow through a fracture with diffusion into the matrix. The assumptions made include: streamlines connecting the injection and withdrawal point can be modeled as a dipole of equal strength, flow along each streamline is one dimensional, and there is a constant Peclet number for each streamline. In contrast to many other field tracer studies performed in fractured rock, the actual travel length between piezometers was not known. Modeling was accomplished by fitting the characteristics of the tracer breakthrough curves (BTCs), such as arrival times of the peak concentration and the center of mass. The important steps were to determine the fracture aperture (240 microm) based on the parameters that influence the rate of matrix diffusion (this controls the arrival time of the peak concentration); estimating the travel distance (11 m) by fitting the time of arrival of the centers of mass of the tracers; and estimating fracture dispersivity (0.5 m) by fitting the times that the inflection points occurred on the front and back limbs of the BTCs. This method works even though there was dilution in the withdrawal well, the amount of which can be estimated by determining the value that the modeled concentrations need to be reduced to fit the data (approximately 50%). The use of two tracers with different diffusion coefficients was not necessary, but it provides important checks in the modeling process because the apparent retardation between the two tracers is evidence of matrix diffusion and the BTCs of both tracers need to be accurately modeled by the best fit parameters.     

Impact of grout curtains on karst groundwater behaviour: an example from the Dinaric karst

Grout curtains are vertical grout walls installed in the ground. In karst terrains, their construction is primarily connected with dams and reservoirs. Their main role is to increase water tightness and to prevent progressive erosion, blocking possible seepage paths along karst fissures and conduits. In this article, changes in the behaviour of the groundwater level (GWL) and the water temperature in nine deep piezometers, which were caused by the construction of a grout curtain at the ?ale Reservoir on the Cetina River (Croatia), were analysed. The total length of the grout curtain is 3966 m. It spreads 120 m below the dam. The most analysed data are from the period after the dam had been built. Only few data and figures concern the comparison between pre‐ and post‐dam periods. The hourly data of the GWL and the water temperature were analysed for the period between 1 September 2008 at 02:00 h to 31 December 2009 at 23:00 h (11 687 h total) in six deep piezometers (marked in the text and figures as 1, 2, 3, 4, 5 and 6). For three piezometers (marked in the text and figures as A, B and C), some discontinuous measurements of the GWL and the water temperature were available for analysis. The construction of the grout curtain made strong, sudden and possibly dangerous changes to the characteristics of the aquifer and the circulation of groundwater in the local area. Special attention is paid to analyses of the behaviour of the hourly GWL data measured in the piezometers pairs (two neighbouring piezometers, one inside and the other outside of the grout curtain). During more than 80% of the analysed period, the GWL was higher in the piezometer inside the grout curtain than the one outside of it. The intensity and range of the dynamics of GWL was higher in piezometer outside the grout curtain than the inside ones. After the construction of the grout curtain, the maximum measured hydrostatic pressure on some parts of the grout curtain was approximately 40 m. It changes quickly in both time and direction. The water temperature was found to be similar in all of the measured piezometers, and it varies between 10.2 and 15.7 °C with an average value of 12.7 °C. Copyright © 2011 John Wiley & Sons, Ltd.     

Identifying connections in a fractured rock aquifer using ADFTs

Fractured rock aquifers are difficult to characterize because of their extremely heterogeneous nature. Developing an understanding of fracture network hydraulic properties in these aquifers is difficult and time consuming, and field testing techniques for determining the location and connectivity of fractures in these aquifers are limited. In the Clare Valley, South Australia, well interference is an important issue for a major viticultural area that uses a fractured aquifer. Five fracture sets exist in the aquifer, all dipping > 25 degrees . In this setting, we evaluate the ability of steady-state asymmetric dipole-flow tests (ADFTs) to determine the connections between a test well and a set of piezometers. The procedure involves dividing a test well into two chambers using a single packer and pumping fluid from the upper chamber to the lower chamber. By conducting a series of tests at different packer elevations, an "input" signal is generated in fracture zones connected to the test well. By monitoring the "output" response of the hydraulic dipole field at piezometers, the connectivity of the fractures between the test well and piezometers can be determined. Results indicate the test well used in this study is connected in a complex three-dimensional geometry, with drawdown occurring above and below areas of potentiometric buildup. The ADFT method demonstrates that the aquifer evaluated in this study cannot be modeled effectively on the well scale using continuum flow models.     

A Simple and Affordable System for Installing Shallow Drive Point Piezometers

This paper describes a drive point system for installing small‐diameter (15 to 25 mm ID) piezometers to depths of several metres in unconsolidated sediments. The system fills the gap between (1) heavy duty drive point systems powered by drilling rig hydraulics or air hammers that are capable of installing large diameter drive points to depths of many tens of metres and (2) manually driven systems that typically install 10 mm ID or smaller tubing to depths of <2 m. Unlike many existing systems, which install piezometers inside an outer casing that is later removed, our system protects the piezometer screen inside the casing and extends it only once the casing is driven to the desired depth. This avoids clogging of the screen during installation and the risk of creating an annulus around the piezometer, which can provide a preferential pathway for water movement. The piezometer has a larger diameter than most manually driven systems, and thus has a higher yield; it also permits use of most commercially available pressure transducers and electrical conductivity sensors. The piezometers have been successfully installed to depths of up to 6 m using an electric hammer. The system overcomes some issues associated with existing systems and provides the advantages of affordability, rapid installation, mechanical assistance and manual portability.     

Prediction of Groundwater Level in Ardebil Plain Using Support Vector Regression and M5 Tree Model

The Ardebil plain, which is located in northwest Iran, has been faced with a recent and severe decline in groundwater level caused by a decrease of precipitation, successive long‐term droughts, and overexploitation of groundwater for irrigating the farmlands. Predictions of groundwater levels can help planners to deal with persistent water deficiencies. In this study, the support vector regression (SVR) and M5 decision tree models were used to predict the groundwater level in Ardebil plain. The monthly groundwater level data from 24 piezometers for a 17‐year period (1997 to 2013) were used for training and test of models. The model inputs included the groundwater levels of previous months, the volume of entering precipitation into every cell, and the discharge of wells. The model output was the groundwater level in the current month. In order to evaluate the performance of models, the correlation coefficient (R) and the root‐mean‐square error criteria were used. The results indicated that both SVR and M5 decision tree models performed well for the prediction of groundwater level in the Ardebil plain. However, the results obtained from the M5 decision tree model are more straightforward, more easily applied, and simpler to interpret than those from the SVR. The highest accuracy was obtained using the SVR model to predict the groundwater level from the Ghareh Hasanloo and Khalifeloo piezometers with R = 0.996 and R = 0.983, respectively.     

Application of harmonic analysis of water levels to determine vertical hydraulic conductivities in clay-rich aquitards

A harmonic analysis method was used to determine vertical hydraulic conductivities (Kv) in geologic media between vertically separated piezometers using water level measurements. In this method, each water level time series was filtered and then decomposed using harmonic analysis into a sum of trigonometric components. The phase and amplitude of each harmonic function were calculated. These data were used to estimate Kv values between vertically separated data sets assuming one-dimensional transient flow. The method was applied to water level data collected from nested piezometers at two thick clay-rich till aquitards in Saskatchewan, Canada. At one site, routine water levels were measured in 12 piezometers (installed between 1 and 29 m below ground surface) since installation (1995). At the other site, water levels were measured in seven piezometers (installed between 4 and 53 m below ground surface) since installation (1998-1999). The Kv calculated using harmonic analysis decreased with depth below the water table at both sites, approaching matrix estimates of hydraulic conductivity between 10 and 11 m and between 21 and 43 m below ground surface. These depths reflected the depth of extensive vertical fracturing at the sites and showed that the depth of fracturing may be site specific.     

Importance of the vadose zone in analyses of unconfined aquifer tests

Analytical models commonly used to interpret unconfined aquifer tests have been based on upper-boundary (water table) conditions that do not adequately address effects of time-varying drainage from the vadose zone. As a result, measured and simulated drawdown data may not agree and hydraulic parameters may be inaccurately estimated. A 72-hour aquifer test conducted in Cape Cod, Massachusetts, in a slightly heterogeneous, coarse-grained, glacial outwash deposit was found to be a good candidate for testing models with different upper-boundary conditions. In general, under the commonly invoked assumption of instantaneous drainage, measured and simulated drawdowns were found to agree with one another only at late time and early time. In the intermediate-time range, because of delayed drainage, measured drawdowns always exceeded simulated values, most noticeably in piezometers located near the water table. To reduce these discrepancies, an analytical model was developed that can fully account for time-varying drainage given that the aquifer is not strongly heterogeneous. The approach is flexible as the model, which makes use of empirical relations, does not constrain drainage to follow any particular functional relation. By this approach, measured and simulated drawdowns agree over the complete time range, and the estimated parameters are consistent with prior studies and with what is known about the aquifer geometry, stratigraphy, and composition. By properly accounting for vadose zone drainage, it was found that realistic estimates of all hydraulic parameters, including specific yield, could be obtained with or without the use of late-time data.     

An inverse problem methodology to identify flow channels in fractured media using synthetic steady-state head and geometrical data

We present a methodology for identifying highly-localized flow channels embedded in a significantly less permeable medium using steady-state head and geometrical data. This situation is typical of fractured media where flows are often strongly channeled at the scales of interest (10 m–1 km). The objective is to identify both geometrical and hydraulic characteristics of the conducting structures. Channels are identified in decreasing order of importance by successive optimizations of an objective function. The identification strategy takes advantage of the hierarchical flow organization to restrict the dimension of the solution space of each individual optimization step. The characteristics of the secondary channels are strongly determined by the main flow channels. The latter are slightly modified by the secondary channels through the addition of a regularization term to the main channel characteristics in the objective function. As the objective function is strongly non-convex with numerous local minima, inversion is performed using a stochastic algorithm (simulated annealing). We assess the possibilities of the hierarchical identification strategy on simple synthetic steady-state flow configurations where hydraulic data are made up of 25 regularly spaced heads and of the boundary conditions. Those flow structures that are dominated by at most two simple channels can be identified with these head data only. Configurations comprising up to three complex and interconnected channels can still be identified with additional geometrical information including the distances of piezometers to their closest channel. The capabilities of the hierarchical identification strategy are limited to flow structures dominated by at most three equivalent flow channels. We finally discuss the perspectives of application of the method to transient-state data obtained on a more restricted number of piezometers.     

Understanding the Geometry of Connected Fracture Flow with Multiperiod Oscillatory Hydraulic Tests

An understanding of the spatial and hydraulic properties of fast preferential flow pathways in the subsurface is necessary in applications ranging from contaminant fate and transport modeling to design of energy extraction systems. One method for the characterization of fracture properties over interwellbore scales is Multiperiod Oscillatory Hydraulic (MOH) testing, in which the aquifer response to oscillatory pressure stimulations is observed. MOH tests were conducted on isolated intervals of wells in siliciclastic and carbonate aquifers in southern Wisconsin. The goal was to characterize the spatial properties of discrete fractures over interwellbore scales. MOH tests were conducted on two discrete fractured intervals intersecting two boreholes at one field site, and a nest of three piezometers at another field site. Fracture diffusivity estimates were obtained using analytical solutions that relate diffusivity to observed phase lag and amplitude decay. In addition, MOH tests were used to investigate the spatial extent of flow using different conceptual models of fracture geometry. Results indicated that fracture geometry at both field sites can be approximated by permeable two‐dimensional fracture planes, oriented near‐horizontally at one site, and near‐vertically at the other. The technique used on MOH field data to characterize fracture geometry shows promise in revealing fracture network characteristics important to groundwater flow and transport.     

A Syringe and Cartridge Method for Down-Hole Sampling for Trace Organics in Ground Water

A newly developed technique which allows the down-hole sampling and subsequent analysis of ground water for trace organic contaminants was tested during an investigation of contaminant migration at an inactive landfill site in Burlington, Ontario, Canada. The sampling device, which is lowered down piezometers with a tube, consists of a small cylindrical cartridge of sorbent material attached to a syringe. Vacuum or pressure applied at the surface controls the movement of the plunger in the syringe. The volume of the syringe determines the volume of sample water that passes through the cartridge. The cartridge is removed from the syringe at the surface. One cartridge is used for each sampling; the syringe is reusable. The residual water in the cartridge is removed in the laboratory, and the cartridge is desorbed to a fused silica capillary column for analysis by gas chromatography (GC). The analyses discussed here were performed on a GC/mass spectrometer/data system (GC/MS/DS). Of the many organic compounds that were identified in the samples, three compounds were clearly landfill-related: 1,1,1-trichloroethane, chlorobenzene, and para-dichlorobenzene. The three compounds were found at levels substantially above blank levels in 9, 5, and 5 piezometers, respectively. The average concentrations were 14., 5.3, and 0.88μg/1 (ppb), respectively. The pooled coefficients of variation for the analyses for the three compounds were 27., 6.9, and 6.4%, respectively. The volatility of 1,1,1-trichloroethane was probably the cause of the greater variability in its analytical data. The main advantages of the technique over most conventional sampling methods include: (1) down-hole sampling in a manner which minimizes the potential for volatilization losses; (2) avoidance of passage of the sample through long sections of tubing that may contaminate the sample or cause adsorptive losses; (3) convenience of sample handling, storage, and shipping; and (4) high sensitivity.     

A coupled vertically integrated model to describe lateral exchanges between surface and subsurface in large alluvial floodplains with a fully penetrating river

This paper presents a vertically averaged model for studying water and solute exchanges between a large river and its adjacent alluvial aquifer. The hydraulic model couples horizontal 2D Saint Venant equations for river flow and a 2D Dupuit equation for aquifer flow. The dynamic coupling between river and aquifer is provided by continuity of fluxes and water level elevation between the two domains. Equations are solved simultaneously by linking the two hydrological system matrices in a single global matrix in order to ensure the continuity conditions between river and aquifer and to accurately model two‐way coupling between these two domains. The model is applied to a large reach (about 36 km²) of the Garonne River (south‐western France) and its floodplain, including an instrumented site in a meander. Simulated hydraulic heads are compared with experimental measurements on the Garonne River and aquifer in the floodplain. Model verification includes comparisons for one point sampling date (27 piezometers, 30 March 2000) and for hydraulic heads variations measured continuously over 5 months (5 piezometers, 1 January to 1 June 2000). The model accurately reproduces the strong hydraulic connections between the Garonne River and its aquifer, which are confirmed by the simultaneous variation of the water level in the river and in piezometers located near the river bank. The simulations also confirmed that the model is able to reproduce groundwater flow dynamics during flood events. Given these results, the hydraulic model was coupled with a solute‐transport component, based on advection‐dispersion equations, to investigate the theoretical dynamics of a conservative tracer over 5 years throughout the 36 km² reach studied. Meanders were shown to favour exchanges between river and aquifer, and although the tracer was diluted in the river, the contamination moved downstream from the injection plots and affected both river banks. Copyright © 2008 John Wiley & Sons, Ltd.     

Inferring Heterogeneity in Aquitards Using High-Resolution δD and δ18O Profiles

Vertical depth profiles of pore water isotopes (δD and δ¹⁸O) in clay-rich aquitards have been used to show that solute transport is dominated by molecular diffusion, to define the timing of geologic events, and to estimate vertical hydraulic conductivity. The interpretation of the isotopic profiles in these studies was based on pore water samples collected from piezometers installed in nests (typically 4 to 15 piezometers) over depths of 10 to 80 m. Data from piezometer nests generally have poor vertical resolution (meters), raising questions about their capacity to reveal the impact of finer scale heterogeneities such as permeable sand bodies or fractured till zones on solute transport. Here, we used high-resolution (30-cm) depth profiles of δD and δ¹⁸O from two continuously cored boreholes in a till aquitard to provide new insights into the effects of sand bodies on solute transport. High-resolution core-derived profiles indicate that such heterogeneities can cause major deviations from one-dimensional diffusion profiles. Further, comparison of piezometer-measured values with best-fit diffusion trends shows subtle deviations, suggesting the presence of heterogeneities that should not be ignored. High-resolution profiles also more clearly defined the contact between the highly fractured oxidized zone and the underlying unoxidized zone than the piezometers.     

A Wet/Wet Differential Pressure Sensor for Measuring Vertical Hydraulic Gradient

Vertical hydraulic gradient is commonly measured in rivers, lakes, and streams for studies of groundwater–surface water interaction. While a number of methods with subtle differences have been applied, these methods can generally be separated into two categories; measuring surface water elevation and pressure in the subsurface separately or making direct measurements of the head difference with a manometer. Making separate head measurements allows for the use of electronic pressure sensors, providing large datasets that are particularly useful when the vertical hydraulic gradient fluctuates over time. On the other hand, using a manometer-based method provides an easier and more rapid measurement with a simpler computation to calculate the vertical hydraulic gradient. In this study, we evaluated a wet/wet differential pressure sensor for use in measuring vertical hydraulic gradient. This approach combines the advantage of high-temporal frequency measurements obtained with instrumented piezometers with the simplicity and reduced potential for human-induced error obtained with a manometer board method. Our results showed that the wet/wet differential pressure sensor provided results comparable to more traditional methods, making it an acceptable method for future use.     

Electronic acquisition of hydrologic data from intensively instrumented hillslopes

A new concept in recording data from a large network of transducers in the field is described. Each transducer is equipped with an addressable switching unit enabling parallel connection by a single four wire cable and sequential interrogation from a micro-computer controlled data logger. A simple water level transducer suitable for both large stilling wells and piezometers, which returns an audio frequency signal with pulse width proportional to water level, is described. The use of audio frequency signals enables telephone grade circuits to be used and avoids many of the problems associated with direct current signals, whether current or voltage, commonly used at present. A field installation of 30 piezometers, a tipping bucket raingauge, a weir-stage recorder and logger controlled water sampler is described and examples given of the data collected from a single piezometer transect during a major storm event.     

Some Biases in Sampling Multilevel Piezometers for Volatile Organics

Multilevel piezometers are cost-effective monitoring devices for determining the three-dimensional distribution of solutes in ground water. Construction includes flexible tubing (plastic or Teflon®). Their sampling is subject to a number of'potential biases, particularly: (1) losses of volatile organic solutes via volatilization, (2) sorption onto the flexible tubing of the piezometers, (3) leaching of organics from this tubing, and (4) collection of unrepresentative samples due to inadequate piezometer flushing. It is shown that these biases are minimal or are easily controlled in most situations.
Another source of bias has been recognized. Organic solutes present in ground water above the screened level can penetrate the flexible plastic or Teflon tubing and contaminate the sampled water being drawn through this tubing. Laboratory tests and field results indicate this transmission causes low organic contaminant concentrations to be erroneously attributed to ground water which is free of such contaminants. The transmitted organics apparently desorb from the plastic tubing during flushing of even 40 piezometer volumes.
Recognition of this transmission problem provides for a better interpretation of existing organic contaminant distribution data. Caution is advised when considering the use of these monitoring devices in organic solute contaminant studies.