减围压平面应变压缩试验条件下丰浦砂中剪切带特性研究

不同于常规土体单元试验中恒定围压的应力路径,进行了减围压（卸载）应力路径下丰浦砂的平面应变压缩试验,研究了初始围压和初始相对密度对砂土的剪切强度和剪切带特性的影响。结合二维数字图像（DIC）相关方法,分析剪切带的形成过程,对剪切带的厚度和倾角及其影响因素进行定量地分析。研究结果表明,剪切带形成于峰值剪切强度之前;对于密实丰浦砂试样,随着围压的增加,其剪切强度(最大有效主应力比)减小且峰值强度出现越晚,剪切带厚度减小而剪切带倾角变化不大;丰浦砂试样的相对密度越高,剪切强度越大且峰值强度出现越早,剪切带厚度越小而剪切带倾角越高。此外,基于峰值内摩擦角的Coulomb公式可以较好地预测平面应变试验条件下丰浦砂的最大剪切带倾角。     

Undrained behaviour of polypropylene fibre reinforced sandy soil under monotonic loading

Soil improvement using fibres is widely used in soil stabilisation to prevent sand liquefaction. In order to study the undrained behaviour and liquefaction resistance of sand reinforced with polypropylene fibres, a series of triaxial compressive tests were conducted on unreinforced and reinforced Chlef sand with different contents of polypropylene fibres (0, 0.3, 0.5 and 0.8%). Samples were prepared at 30% and 80% relative densities representing loose and dense states respectively, and triaxial tests were performed at confining pressures of 50, 100 and 200 kPa. Tests results show that fibre inclusion has a significant effect on the shear strength and dilation of sandy soil. The increase in strength is function of fibre content, relative density and confining pressure. The maximum strength improvement for both loose and dense fibre-reinforced sand is more pronounced at higher confining pressure and at higher fibre content.     

Influence of relative density,particle shape,and stress path on the plane strain compression behavior of granular materials

Two types of stress path-controlled plane strain compression tests were performed on both loose and dense specimens of angular and sub-angular sands and two rounded glass beads with different particle sizes. Digital image correlation method was used to analyze local deformation developments, especially shear band patterns. The material behavior in response to shearing has been found to be dependent on the relative density, particle shape, and stress path. The results of analysis on local deformation developments showed that the onset of shear bands occurred prior to their peak strengths in both dense and loose specimens. The growth rates of local maximum shear strain along a shear band were approximately consistent with an increasing global axial strain after the onset of shear band. The shear band width was influenced by both the mean particle size and the particle shape. The measured shear band inclination angles were in between those estimated by Coulomb’s and Roscoe’s formulas.     

The influence of grading on the shear strength of loose sands in stress-controlled ring shear tests

Three silica sand samples—well graded, intermediately graded, and narrowly graded—having different uniformity coefficients, were constituted to allow the investigation of the influence of particle size distribution on their mechanical behavior. Using a ring shear apparatus, samples were tested under a wide range of laboratory conditions. Results of the tests clearly indicate that, for specimens confined under identical stress conditions, well-graded specimens have higher values of peak and steady state strengths than the rest of the specimens. A relationship between uniformity coefficient and shear strengths shows that the higher the uniformity coefficient, the higher the shear strength. On account of these, well-graded specimens have higher static liquefaction resistance than the poorly graded specimens. Within the range of normal stresses employed in the tests, results reveal that not only are poorly graded sands more likely to suffer higher postfailure strength reduction, but that their steady-state strengths are easily reduced to zero, the magnitude of the confining stress notwithstanding. This reduction of shear resistance to zero has been described as complete liquefaction in this paper. While almost all of the narrowly graded specimens suffered complete liquefaction, widely graded ones did not; an observation that seem to highlight the influence of grading on the mechanical behavior of the sands.     

Anisotropic shear strength characteristics of a tailings sand

The deposition process of tailings in a tailings dam may lead to the anisotropy of mechanical properties of tailings. To investigate the anisotropic shear strength characteristics of a tailings sand, samples deposited under gravity were sheared in a modified direct shear apparatus along different orientations of the shear planes relative to the bedding plane. The experimental results reveal that the anisotropy has a substantial effect on the peak shear strength of the tailings sand, leading to a variation in peak friction angle of 10°. It is found that the effect of anisotropy on the peak shear strength of the tailings sand is mainly attributed to the effect of anisotropy on soil dilatancy. On the other hand, the effect of anisotropy on the residual friction angle of the tailing sand is relatively smaller, likely due to the partial erasure of anisotropy at large shear deformation. The degree of anisotropy is reduced by an increase in normal stress. To achieve more accurate stability analysis of tailings dams, it is suggested to take into account the shear strength anisotropy of tailings soils.     

Notes on the effect of grain crushing on the granular soil behaviour

Two granular materials — alluvial quartzy Zbraslav sand and granular silica gel — were tested with the intention to demonstrate the effect of grain crushing. Stepwise transformation of the compression curve produced by progressive grain crushing was observed. Due to grain crushing, shear strength envelope became nonlinear, and the behaviour was no more physically isomorphous. The shear stress–strain diagrams acquire a typical wavy (garland-like) form, induced by periodic softening and hardening of the soil response. The intensity of grain crushing depends (in addition to stress level, grain resistance and time) on the shear path. In the crushing phase, initial porosity and angularity play a secondary role. Many other behavioural features common with granular soils (like increase in dilatancy with density and grain size) are suppressed. Grain crushing thus produces a qualitatively different feature of geomaterial behaviour with grave practical consequences (dense sand, e.g. starts to behave like loose).     

Influence of Lode angle‐dependent failure criteria on shear localization analysis in sand

Geotechnical experiments show that Lode angle‐dependent constitutive formulations are appropriate to describe the failure of geomaterials. In the present study, we have adopted one such class of failure criteria along with a versatile constitutive relationship to theoretically analyze the effects of Lode angle on localized shear deformation or shear band formation in loose sand for both drained and undrained conditions. We determine the variation in the possible stress states for shear localization due to the introduction of Lode angle by considering the localized deformation as a bifurcation problem. Further, similar bifurcation analysis is performed for the stress states along a specific loading path, namely, plane strain compression at the constitutive level. In addition, the plane strain compression tests have been simulated as a boundary value finite element problem to see how Lode angle affects the post‐localization response. Results show that the inclusion of a Lode angle parameter within the failure criterion has considerable effects on the onset, plastic strain, and propagation of shear localization in loose sand specimens. For drained condition, we notice early inception of shear localization and multiple band formation when the Lode angle‐dependent failure criterion is used. Undrained localization characteristics, however, found to be independent of Lode angle consideration.     

Enhancing the interface friction between glass fiber-reinforced polymer sheets and sandy soils through sand coating

ABSTRACT

Soil-pile interface friction is an important geotechnical engineering factor to be considered in achieving a safe and cost-effective design. Conventional materials such as concrete, steel, and wood exhibit serious long-term soil substructure problems, particularly with regard to durability, deterioration, and corrosion. Fiber-reinforced polymer (FRP) composites are potential alternatives for addressing these long-term problems. This paper describes the results of an experimental study of the interface friction between sandy soil and glass FRP (GFRP) sheets coated with different ratios of sand per unit of surface area. A direct shear test was used to study 18 different groups of GFRP specimens. The test parameters were the amount of silica sand coating and normal stresses in the direct shear tests. The GFRP specimens were sheared against three types of soil: sand, silty sand, and sandy lean-clay, of which the first two were used in both dense and loose states. The experimental results showed that coating the GFRP sheets with silica sand was effective in enhancing the interface friction with sandy soils under different normal stresses. A pile implication analysis was also performed to compare the effect of sand coated GFRPs on the load capacity of friction piles with different length to diameter ratios.     

钙质砂抗剪强度特性的环剪试验

珊瑚礁沉积的钙质砂与石英砂的物理力学性质有较大差别。对取自南海岛礁的钙质砂进行了单次往返环剪试验以分析钙质砂的抗剪强度特性,试验中考虑了相对密实度和竖向应力对结果的影响,并与相同级配和试验条件下的石英砂进行对比分析。结果表明：钙质砂正向剪切时应力-位移曲线为软化型,具有明显的残余强度特性,而反向剪切时则表现为硬化型,正向和反向剪切强度基本一致;石英砂正向剪切和反向剪切均表现为软化型。钙质砂正向剪切和反向剪切残余强度与峰值强度的比值在0.75～0.93之间;石英砂正向剪切和反向剪切残余强度与对应峰值强度的比值在0.89～0.96之间。相同级配和试验条件下,钙质砂残余强度均大于石英砂,且强度比值基本保持在1.05～1.3之间。在100、200 kPa竖向荷载作用下,钙质砂0.5～2.0 mm的颗粒发生了破碎,破碎率分别为4%和6%。     

斜椭圆应力路径下饱和松砂动力特性试验研究

利用空心圆柱扭剪仪模拟斜入射地震波作用形成的斜椭圆应力路径,对比研究了等向固结条件下饱和福建标准松砂在循环斜椭圆、圆形、扭剪、三轴路径下的动力特性。试验研究表明：土体循环孔压发展存在陡升型和陡降型两种模式;圆形路径下累积孔压增长速率最快,循环扭剪最小;归一化孔压与斜椭圆的倾角无关,但受斜椭圆长短轴比及动应力比影响。砂土的不排水动强度与动应力路径密切相关,循环扭剪和循环三轴最大,循环斜椭圆次之,圆形路径最小。地震波从特定角度入射时,形成近似圆形路径,若只将地震波视为垂直入射的S波,将高估地基土体抗液化强度。     

基于数字图像测量系统的饱和细砂渐进破坏特性研究

基于亚像素角点检测的数字图像测量系统能够记录三轴试样表面方块角点的位移,从而获得试样表面每一时刻的局部应变及应变场。分析了试样不同位置的局部径向应变在剪切过程中的变化,获得了以不同初始成样含水率制备的松砂和密砂试样在不同特征时刻的应力与应变的特征值。通过轴向应变场的变化分析了从应变局部化出现到剪切带发育、形成的这一完整的渐进破坏过程,总结了剪切带形成时的局部最大轴向应变特征值,并定性地分析了剪切带内、外土体在渐进破坏过程中不同的轴向应变增长率。试验结果表明：在应变场中试样应变局部化明显,并可以依此确定应变局部化的出现、剪切带的形成;对于密砂及初始含水率为0%制备的松砂试样,应力在应变局部化出现之初即达到峰值,剪切带形成时应力已经开始下降,进入应变软化阶段;以初始含水率为6%和12%制备的松砂试样在达到应力峰值时剪切带已经形成;剪切带内土体的局部轴向应变增长幅度比剪切带外的土体大得多。试样整体轴向应变的增大主要是由剪切带内土体剪切破坏产生的较大轴向应变所致。     

Strength of two structured soils in triaxial compression

Oil sands are dense granular materials with interlocked structure and clay shales are heavily overconsolidated clays. They are classified as structured soil or weak rock, exhibiting high peak strength with severe softening and dilation, particularly at low confining stress. The triaxial compression test results indicate that both materials yield linear Mohr–Coulomb envelopes with an apparent cohesion for peak and residual strengths. However, the strength components mobilized from these two materials are very different. This paper investigates if these strength parameters are intrinsic properties or responses derived in triaxial compression conditions. Computer tomography scanning technique is used to aid in examining the micro‐structural features of the sheared specimens such as shear banding pattern, shear band thickness, spatial porosity distributions inside and outside shear bands. These micro‐structural features are used to explain the macro‐deformation response observed in the triaxial compression tests. Mobilization of strength components derived from interlocked structure, cementation, dilation, rolling and critical state are analysed for pre‐, post‐peak softening and residual stages. It is found that the empirical correlation such as Mohr–Coulomb failure criterion based on triaxial compression test results does not necessarily reflect the intrinsic properties of the test materials. Testing conditions are embedded in the empirical correlation. Copyright © 2001 John Wiley & Sons, Ltd.     

Dynamic Properties of Soft Clay and Loose Sand from Seismic Centrifuge Tests

Appropriate evaluation of shear modulus and damping characteristics of soils subjected to dynamic loading is key to accurate seismic response analysis and soil modeling programs. Dynamic centrifuge experiments were conducted at C-CORE (Memorial University of Newfoundland) centrifuge center to investigate the dynamic properties and seismic response of soft clay and dry loose sand strata. Soft clay with shear strength of about 30 kPa and well graded silica sand at about 35% relative density were employed in a rigid container to simulate local site effects. Several earthquake-like shaking events were applied to the model to evaluate variation of shear modulus and damping ratio with shear strain amplitude and confining pressure, and to assess their effects on site response. The estimated modulus reduction and damping ratio were compared to the predictions of empirical formulae and resonant column tests for both soft clay and loose sand. The evaluated shear modulus and damping ratio were found to be dependent on confining pressure in both soil types. Modulus variation in both soils agreed well with the empirical curves and resonant column test results. However, the sand modulus values were slightly higher than the empirical relations and resonant column tests. This discrepancy is attributed to higher stress and densification of sand during large amplitude shaking applied to the model. The damping ratio at shear strains lower than 0.5% was in reasonable agreement with the empirical curves and the resonant column tests in both clay and sand models, but was generally higher at shear strain larger than 0.5%.     

干湿循环对非饱和膨胀土抗剪强度影响的试验研究

膨胀土是一种气候敏感性土体,研究在干湿循环过程中膨胀土剪切强度的变化,对了解在自然界周期性蒸发和降雨作用下原位膨胀土体工程性质的变化以及由此导致的地质灾害发生过程具有重要意义。文中以重塑非饱和膨胀土为研究对象,模拟了3次干湿循环过程,对每次干燥路径中的试样进行了直剪试验,重点分析含水率、正压力及干湿循环次数对膨胀土剪切强度的影响,得到如下主要结果：（1）在干燥过程中,随着含水率的减小,试样的刚度、脆性、抗剪强度值（峰值剪切应力）、抗剪强度指标（黏聚力、内摩擦角）及抗剪强度损失（峰值强度与残余强度之差）均呈增加趋势;（2）正压力越高,试样的剪切强度和残余强度越大,而破坏后的峰值强度损失越小,破坏韧性增加;（3）在3次干燥过程中,试样的剪切强度及黏聚力呈先增加后减小的趋势,在第二次干燥过程中达到峰值,但内摩擦角受干湿循环的影响无明显规律;（4）试样经历多次干湿循环后,其剪切特性越来越类似于超固结土,脆性显著增加;（5）干燥过程和干湿循环对试样残余剪切强度的影响都不明显,残余剪切强度基本都在100 kPa附近变化;（6）非饱和膨胀土在干湿循环及干燥过程中剪切强度的变化除了与吸力有关外,还与其微观结构调整和裂隙发育状态密切相关,需要综合非饱和土力学和土质学理论对试验现象进行分析。     

中主应力对饱和松砂不排水单调剪切特性的影响

利用土工静力-动力液压-三轴扭转多功能剪切仪,针对相对密度为30 %的福建标准砂,在不排水条件下控制主应力方向、中主应力系数、平均主应力保持不变,进行了单调剪切试验。以此着重探讨了中主应力系数对相变有效内摩擦角、峰值有效内摩擦角及有效应力路径的影响。研究表明,中主应力系数对在不排水单调剪切条件下饱和松砂的强度参数具有显著的影响,而对有效应力路径及应力-应变关系发展模式影响较小。基于广义双剪强度准则,从理论上探讨了土的强度参数对于中主应力的依赖性,并与试验结果进行了对比。     

Laboratory Investigation into the Effects of Silty Fines on Liquefaction Susceptibility of Chlef (Algeria) Sandy Soils

In a number of recent case studies, the liquefaction of silty sands has been reported. To investigate the undrained shear and deformation behaviour of Chlef sand–silt mixtures, a series of monotonic and stress-controlled cyclic triaxial tests were conducted on sand encountered at the site. The aim of this laboratory investigation is to study the influence of silt contents, expressed by means of the equivalent void ratio on undrained residual shear strength of loose, medium dense and dense sand–silt mixtures under monotonic loading and liquefaction potential under cyclic loading. After an earthquake event, the prediction of the post-liquefaction strength is becoming a challenging task in order to ensure the stability of different types of earth structures. Thus, the choice of the appropriate undrained residual shear strength of silty sandy soils that are prone to liquefaction to be used in engineering practice design should be established. To achieve this, a series of undrained triaxial tests were conducted on reconstituted saturated silty sand samples with different fines contents ranging from 0 to 40 %. In all tests, the confining pressure was held constant at 100 kPa. From the experimental results obtained, it is clear that the global void ratio cannot be used as a state parameter and may not characterize the actual behaviour of the soil as well. The equivalent void ratio expressing the fine particles participation in soil strength is then introduced. A linear relationship between the undrained shear residual shear strength and the equivalent void ratio has been obtained for the studied range of the fines contents. Cyclic test results confirm that the increase in the equivalent void ratio and the fines content accelerates the liquefaction phenomenon for the studied stress ratio and the liquefaction resistance decreases with the increase in either the equivalent void ratio or the loading amplitude level. These cyclic tests results confirm the obtained monotonic tests results.     

Yielding of Silt at High Temperature and Suction Magnitudes

This study presents an evaluation of yielding mechanisms for unsaturated, compacted silt using drained triaxial compression tests with control of elevated temperatures and high suction magnitudes. After anisotropic compression, some compacted silt specimens were heated by approximately 40 °C before a suction of approximately 300 MPa was applied, while others were heated after suction application. A frictional response was observed for the specimens sheared under high suction magnitudes, in the form of a consistent increase in peak shear strength with increasing net confining stress. An effective stress analysis was used to evaluate the trends in the peak shear stress and the role of stress history for the different specimens. A single peak failure envelope was observed when the shear strength data was interpreted in terms of the mean effective stress. Changes in preconsolidation stress were estimated by identifying the intersections between a thermo-elasto-plastic yield function and the experimental peak shear strength values. Soil specimens heated before application of high suction values had lower peak shear strengths than reference specimens at high suction and ambient temperature. This behaviour is consistent with thermal softening trends observed in soils heated under low suction values. However, soil specimens heated after suction application had greater peak shear strengths than the reference specimens. This indicates heating under high suction results in hardening. The impact of suction on the preconsolidation stress was found to be better represented by a power law model at high suction magnitudes than other available models. The estimated preconsolidation stress values were used to evaluate the impacts of stress history on the thermal volume change response, which matched well with data from tests on saturated specimens.     

Influence of size of granulated rubber and tyre chips on the shear strength characteristics of sand–rubber mix

Use of scrap tyres in isolation systems for seismic damping, requires a knowledge of the engineering properties of sand–rubber mixtures (SRM). The primary objective of this study is to assess the influence of granulated rubber and tyre chips size and the gradation of sand on the strength behaviour of SRM by carrying out large-scale direct shear tests. A large direct shear test has been carried out on SRM considering different granulated rubber and tyre chip sizes and compositions. The following properties were investigated to know the effect of granulated rubber on dry sand; peak shear stress, cohesion, friction angle, secant modulus and volumetric strain. From the experiments, it was determined that the major factors influencing the above-mentioned properties were granulated rubber and tyre chip sizes, percentage of rubber in SRM and the normal stress applied. It was observed that the peak strength was significantly increased with increasing granulated rubber size up to rubber size VI (passing 12.5 mm and retained on 9.5 mm), and by adding granulated rubber up to 30%. This study shows that granulated rubber size VI gives maximum shear strength values at 30% rubber content. It was also found that more uniformly graded sand gives an improved value of shear strength with the inclusion of granulated rubber when compared to poorly graded sand.     

中主应力对砂土强度影响的细观机制研究

基于简化的颗粒单元体模型,分析总结了颗粒单元体的基本特点,针对中主应力对砂土强度的影响,重点分析了颗粒单元体之间的相互影响特点。对以往的真三轴试验结果进行了总结,得到了中主应力对砂土强度影响的规律,结合颗粒单元体的两种基本状态及其特点、大孔隙与颗粒单元体结构孔隙的特点以及颗粒单元体间相互影响的特点,揭示了中主应力对砂土强度影响规律的细观物理机制。这些规律包括：松砂的强度随着中主应力的增大是逐渐提高的;密砂随中主应力的增大,强度先提高,当中主应力接近大主应力时,却引起强度的降低;砂土越密实,强度平台段越长;在中主应力接近小主应力阶段,强度随中主应力的增大而提高的快慢与砂土的密实程度有关。     

Undrained behaviour of Changi sand in triaxial and plane-strain compression

The results of an experimental study of the undrained behaviour of Changi sand under axisymmetric and plane-strain conditions are presented. K₀ consolidated undrained plane-strain tests and K₀ or isotropically consolidated triaxial tests on very loose and medium dense specimens were conducted. The undrained behaviour of sand at very loose and medium dense states under plane-strain conditions was characterised and compared with that under axisymmetric conditions. It was observed that the undrained behaviour of very loose and medium dense sand under plane strain is similar to that under axisymmetric conditions. However, because of the formation of shear bands in plane-strain tests, the post-peak behaviour of medium dense sand in plane strain is different from that in triaxial tests. It was also established that an instability line for plane-strain conditions can be defined in a way similar to that for axisymmetric conditions. Using the state parameter, a unified relationship between the normalised slope of instability line and the state parameters can be established for both axisymmetric and plane-strain conditions. Using this relationship, the instability conditions established under axisymmetric conditions can be used for plane-strain conditions.