屈曲约束支撑的研究进展及其在结构抗震加固中的应用

本文首先介绍了屈曲约束支撑(BRB)的最新研究进展。屈曲约束支撑在承受拉力和压力的情况下,表现出相同的滞回性能和优良的耗能能力。文章介绍了近些年来发展和应用比较成熟的一些形式的屈曲约束支撑。对于近些年来这种支撑在一些主要抗震地区的应用进行了回顾。对于新建高层钢结构的大量应用案例和已有结构的抗震加固的应用表明,此种支撑的使用前景非常广阔。     

安装有防屈曲支撑建筑的地震模拟与经济性分析

结合防屈曲支撑拟静力实验的研究成果,用ABAQUS有限元软件模拟一栋建筑的地震反应。比较原设计结构与减少梁柱面积但安装有防屈曲支撑的减缩结构这2种方案下的地震响应,使两者的层间位移角相近并满足规范要求,进而做经济性对比。结果表明,防屈曲支撑可以有效地减小结构地震响应,并且先于梁柱破坏,保护主体结构安全;安装防屈曲支撑的结构在满足设计要求的同时,还可以节省建筑成本,缩短施工工期。     

基于Benchmark模型的抑制屈曲支撑耗能减振作用分析

抑制屈曲支撑可在拉压循环荷载作用下均达到屈服,拉压承载力基本一致,滞回曲线稳定饱满,耗能能力强。基于Benchmark模型对安装抑制屈曲支撑的钢框架结构基于ANSYS的数值分析表明,抑制屈曲支撑不仅可使结构在小震时的抗侧刚度有所提高,同时在大震时通过其往复滞回变形发挥耗能减振作用,大大地降低了结构的地震响应,提高了结构的抗震性能。同时分析表明考虑高阶振型影响的能力谱分析方法是一种更为精确的分析方法。     

Study of a new-type of steel buckling-restrained brace

The rectangle core plate of all-steel buckling-restrained braces(BRBs) usually exhibit obvious local buckling, due to the lack of longitudinal restraint from the encasing tube. To eliminate the undesirable effects, a novel steel BRB is proposed. In this new-type steel BRB, two T-shaped steels are adopted as the minor restraint elements to restrain the core plate instead of infilled concrete or mortar. Meanwhile, the ingot-iron material with low yielding strength and high elongation is applied to the steel core to study the mechanical properties of steel BRBs. To validate the theoretical requirements for the width-to-thickness ratio of the steel core and the thickness of angle steel, quasi-static tests of eight specimens were conducted. The tests focused on the energy dissipation capacity and failure modes of the proposed steel BRBs. Nonlinear finite element analysis was also carried out to validate the experimental results. Both the aforementioned results imply that appropriately designed steel BRBs can meet the performance requirements for BRB components.     

Developing high‐performance aluminum alloy buckling‐restrained braces based on series of low‐cycle fatigue tests

In order to enhance the durability of high‐performance buckling‐restrained braces (BRBs) used in bridge engineering, which are expected to withstand severe earthquakes three times without being replaced, aluminum alloys were employed to manufacture BRBs. A series of low‐cycle fatigue tests, including 18 specimens, were conducted to address the low‐cycle fatigue strength of the aluminum alloy BRB. Test results of all specimens show that stable hysteretic curves were obtained without overall buckling occurrence. Failure mode of the welded aluminum alloy BRB is obviously affected by the ribs' welding under the variable or constant strain amplitude condition. Therefore, another type of aluminum alloy BRB, the bolt‐assembled BRB with or without spot‐welded stoppers, is proposed and tested. Results showed that the low‐cycle fatigue performance of bolt‐assembled BRBs with stoppers improved four to five times compared with welded BRBs. However, the stoppers' spot welding has an adverse effect on the failure mode because the crack, which induced the specimen's failure, initiated from the spot weld toes of the stoppers. Both bolt‐assembled BRBs with and without stoppers can meet the cumulative inelastic deformation requirement proposed for high‐performance BRBs under the constant strain amplitude, not larger than 2%. In addition, under the variable strain amplitude condition, only the bolt‐assembled BRB without stoppers has an excellent cumulative inelastic deformation capacity and sustains two cycles of 2.5% strain amplitude. Finally, recommended Manson–Coffin equations and preliminary cumulative damage formulae for welded and bolt‐assembled BRBs are given as the references of the strain‐based damage evaluation. Copyright © 2011 John Wiley & Sons, Ltd.     

Design method and behavior factor for steel frames with buckling restrained braces

Buckling restrained braces (BRBs) are very effective in dissipating energy through stable tension–compression hysteretic cycles and have been successfully experimented in the seismic protection of buildings. Their behavior has been studied extensively in the last decades and today the level of performance guaranteed by these devices and the technological constrains that have to be fulfilled to optimize their behavior are well known. Furthermore, several companies in the world have developed their own BRBs and are now producing them. In spite of this, many seismic codes (for instance, the EuroCode 8) do not stipulate provisions for the design and construction of earthquake‐resistant structures equipped with BRBs. This discourages the structural engineering community from using these devices and seriously limits their use in structural applications. In this paper a procedure for the seismic design of steel frames equipped with BRBs is proposed. Furthermore, the paper presents a numerical investigation aimed at validating this design procedure and proposing the value of the behavior factor q that should be used for this structural type. To this end, a set of frames with BRBs is first designed by means of several values of q. Then, the obtained frames are subjected to a set of accelerograms compatible with the elastic response spectrum considered in design. The seismic response of the frames is determined by nonlinear dynamic analysis and represented in terms of the ductility demand of BRBs and the internal force demand of nondissipative members (beams and columns). Finally, the largest value of q that leads to acceptable seismic performance of the analyzed frames is assumed as adequate. The value of q is given in the paper as a continuous function of the assumed ductility capacity of the BRBs. Copyright © 2012 John Wiley & Sons, Ltd.     

Seismic reliability of steel moment resisting framed buildings retrofitted with buckling restrained braces

The present paper investigates the seismic reliability of the application of buckling restrained braces (BRBs) for seismic retrofitting of steel moment resisting framed buildings through fragility analysis. Samples of regular three‐storey and eight‐storey steel moment resisting frames were designed with lateral stiffness insufficient to comply with the code drift limitations imposed for steel moment resisting frame systems in earthquake‐prone regions. The frames were then retrofitted with concentrically chevron conventional braces and BRBs. To obtain robust estimators of the seismic reliability, a database including a wide range of natural earthquake ground motion records with markedly different characteristics was used in the fragility analysis. Nonlinear time history analyses were utilized to analyze the structures subjected to these earthquake records. The improvement of seismic reliability achieved through the use of conventional braces and BRBs was evaluated by comparing the fragility curves of the three‐storey and eight‐storey model frames before and after retrofits, considering the probabilities of four distinct damage states. Moreover, the feasibility of mitigating the seismic response of moment resisting steel structures by using conventional braces and BRBs was determined through seismic risk analysis. The results obtained indicate that both conventional braces and especially BRBs improve significantly the seismic behavior of the original building by increasing the median values of the structural fragility curves and reducing the probabilities of exceedance of each damage state. Copyright © 2011 John Wiley & Sons, Ltd.     

近断层地震动下设置BRB的双向减隔震桥梁地震反应

在近断层地震动下桥梁结构将发生较大反应,减隔震设计是减轻地震损伤的重要手段。提出了在桥梁双柱墩横桥向设置防屈曲支撑(BRB),在纵桥向设置铅芯橡胶支座(LRB)的双向减隔震体系。利用Midas Civil软件建立3种不同减隔震方式的桥梁结构模型:LRB仅单向,LRB双向与LRB联合BRB,运用非线性时程分析方法计算了桥墩反应(墩顶侧移角、残余位移角和曲率延性)、LRB支座变形和BRB的耗能特性等。结果表明:在近断层地震动输入下联合设置LRB和BRB的双向减隔震桥梁减震效果明显,相比其它2种方式,能有效降低墩柱的塑性变形及起到保护桥墩的作用。在横桥向,桥墩最大侧移角、残余位移角和最大曲率延性系数都显著降低。     

防屈曲支撑的工作机理及稳定性设计方法

防屈曲支撑(BRBs)是一种兼具普通支撑和金属耗能阻尼器双重功能的新型支撑形式。虽然其概念简单明确,但是工作机理却较为复杂,而目前人们对此类支撑的本质工作机理还没有得到充分的认识,因此很难提出较为全面合理的构件稳定性设计方法。本文对防屈曲支撑的工作机理进行了剖析,比较了目前已有的构件整体稳定性设计方法并指出了其中存在的问题,进一步提出应重点考虑间隙、边界条件以及摩擦力等因素的"强度-刚度"整体稳定设计方法的观点;从理论上推导了支撑内芯屈服段与约束构件之间的局部挤压力计算公式,揭示了支撑构件局部失稳破坏的机理,并进一步提出应重点考虑内芯板件宽厚比、间隙以及局部约束条件三者相关关系的支撑构件局部稳定设计方法的观点。     

Seismic design and hybrid tests of a full‐scale three‐story buckling‐restrained braced frame using welded end connections and thin profile

A series of hybrid and cyclic loading tests were conducted on a three‐story single‐bay full‐scale buckling‐restrained braced frame (BRBF) at the Taiwan National Center for Research on Earthquake Engineering in 2010. Six buckling‐restrained braces (BRBs) including two thin BRBs and four end‐slotted BRBs, all using welded end connection details, were installed in the frame specimen. The BRBF was designed to sustain a design basis earthquake in Los Angeles. In the first hybrid test, the maximum inter‐story drift reached nearly 0.030 rad in the second story and one of the thin BRBs in the first story locally bulged and fractured subsequently before the test ended. After replacing the BRBs in the first story with a new pair, a second hybrid test with the same but reversed direction ground motion was applied. The maximum inter‐story drifts reached more than 0.030 rad and some cracks were found on the gusset welds in the second story. The frame responses were satisfactorily predicted by both OpenSees and PISA3D analytical models. The cyclic loading test with triangular lateral force distribution was conducted right after the second hybrid test. The maximum inter‐story drift reached 0.032, 0.031, and 0.008 rad for the first to the third story, respectively. This paper then presents the findings on the local bulging failure of the steel casing by using cyclic test results of two thin BRB specimens. It is found that the steel casing bulging resistance can be computed from an equivalent beam model constructed from the steel core plate width and restraining concrete thickness. This paper concludes with the recommendations on the seismic design of thin BRB steel casings against local bulging failure. Copyright © 2011 John Wiley & Sons, Ltd.     

Full-scale hybrid test for realistic verification of a seismic upgrading technique of RC frames by BRBs

Scientific research proposing any type of device/technique for seismic protection of buildings is generally based on numerical models that adopt simplifications to make possible extensive analyses. This means that important details of the inelastic response could be neglected. Following this consideration, regardless of the device/technique invented, before it could be put into practice, an experimental verification of the actual structural performance should be conducted by full-scale tests at building level. This issue is investigated in the paper considering seismic retrofit of reinforced concrete (RC) framed structures by buckling-restrained braces (BRBs) as technique to be validated, while hybrid test is selected as tool for experimental validation at building level. The analysed seismic upgrading technique consists in the insertion of BRBs into the RC frame. The upgrading intervention is designed by a method developed in previous studies. This technique responds to an important need of the society. Indeed, existing RC frames showed high vulnerability in occurrence of past earthquakes when they were not originally conceived to sustain horizontal forces. The hybrid test is selected among the available experimental techniques because it allows the experimentation on full-scale specimens with reasonable cost. In this study, a substructure hybrid test was conducted and the results are here presented to (a) evaluate the effectiveness of the design method of BRBs for seismic upgrading, (b) investigate the integration of BRBs in existing RC frame, and (c) show the potentiality of the substructure hybrid test for the experimental verification of innovative techniques for seismic protection of buildings.     

Mathematical modeling and full-scale shaking table tests for multi-curve buckling restrained braces

Buckling restrained braces(BRBs)have been widely applied in seismic mitigation since they were introduced in the 1970s.However,traditional BRBs have several disadvantages caused by using a steel tube to envelope the mortar to prevent the core plate from buckling,such as;complex interfaces between the materials used,uncertain precision,and time consumption during the manufacturing processes.In this study,a new device called the multi-curve buckling restrained brace (MC-BRB) is proposed to overcome these d...     

Hybrid experimental performance of a full‐scale two‐story buckling‐restrained braced RC frame

This paper proposes a novel implementation of buckling‐restrained braces (BRB) in new reinforced concrete (RC) frame construction. Seismic design and analysis methods for using a proposed steel cast‐in anchor bracket (CAB) to transfer normal and shear forces between the BRB and RC members are investigated. A full‐scale two‐story RC frame with BRBs (BRB‐RCF) is tested using hybrid and cyclic loading test procedures. The BRBs were arranged in a zigzag configuration and designed to resist 70% of the story shear. The gusset design incorporates the BRB axial and RCF actions, while the beam and column members comply with ACI 318‐14 seismic design provisions. Test results confirm that the BRBs enhanced the RCF stiffness, strength, and ductility. The hysteresis energy dissipation ratios in the four hybrid tests range from 60% to 94% in the two stories, indicating that BRBs can effectively dissipate seismic input energy. When the inter‐story drift ratio for both stories reached 3.5% in the cyclic loading test, the overall lateral force versus deformation response was still very stable. No failure of the proposed steel CABs and RC discontinuity regions was observed. This study demonstrates that the proposed design and construction methods for the CABs are effective and practical for real applications. Copyright © 2016 John Wiley & Sons, Ltd.     

A multi‐performance design method for seismic upgrading of existing RC frames by BRBs

In the world, many existing buildings with RC framed structure were designed according to old seismic standards and present structural deficiencies. Buckling Restrained Braces (BRBs) can be effective for seismic upgrading of these structures, as pointed out by many studies. Nevertheless, Eurocode 8 (EC8) does not provide any rules for design of BRBs. This lack represents a big obstacle for application of this seismic upgrading technique in Europe. For this reason, a method for the design of seismic upgrading interventions by BRBs is proposed in this paper. The method is obtained as the best between two variants developed, investigated and compared in this paper. Based on a numerical investigation, the parameters that control the design method are calibrated to ensure the fulfillment of the Near Collapse performance objective stipulated in EC8. Finally, the capability of the proposed design method in fulfilling also performance objectives not explicitly considered in design is investigated. Copyright © 2016 John Wiley & Sons, Ltd.     

Welded end‐slot connection and debonding layers for buckling‐restrained braces

The debonding mechanism has a significant effect on the performance of a buckling‐restrained brace (BRB). In this paper, a method for estimating the compression strength adjustment factor for any given BRB core strain is presented. Experimental investigations were conducted on four BRBs to examine the efficiency of four different debonding materials in reducing the difference between the cyclic peak compression and tension. Test results indicate that chloroprene rubber is very easy to install and very effective in minimizing the difference between the compressive and tensile capacities. The excellent performance of 13 full‐scale welded end‐slot BRBs (WES‐BRBs) is illustrated through experiments. Cyclic loading test results of a 12.5‐m long jumbo WES‐BRB reveal that its peak compressive strength exceeds 16,800 kN and its maximum core strain reaches 0.035. All WES‐BRBs show satisfactory performance with a very stable hysteresis response, modest peak compressive to tensile strength ratio, and very predictable axial stiffness. These specimens sustain a cumulative plastic deformation of greater than 400 times the yield deformation. The hysteresis responses can be satisfactorily predicted by using a two‐surface plasticity analytical model. Advantages of the welded end‐slot connections are also presented through a discussion on the effects of the BRB yield region length ratio on the effective stiffness, the yield story drift, and the core strain level. Copyright © 2014 John Wiley & Sons, Ltd.     

Seismic performance analysis of BRBs and gussets in a full‐scale 2‐story BRB‐RCF specimen

The implementation of buckling‐restrained braces (BRBs) for new reinforced concrete frame (RCF) constructions is limited. This study investigates the seismic forces and stability in the BRBs and gussets of a 2‐story full‐scale RCF specimen by using Abaqus models and a newly proposed stability evaluation method. The hybrid and cyclic loading test results are accurately predicted by the Abaqus analyses. Existing methods for computing the gusset interface forces for steel buildings from both the brace and the frame actions are compared with the Abaqus results. The applicability of these methods for the BRB‐RCF design is critically evaluated. It is confirmed that the Parallel‐2 method is suitable for estimating the BRB force demand imposed on the corner gusset and the generalized uniform force method is good for the corner gusset at the base. In addition, existing stability evaluation methods for BRBs and gussets are applied to investigate the out‐of‐plane (OOP) buckling of the first‐story BRB observed at the end of tests. The proposed stability model incorporates the BRB restrainer's flexural effects and 4 rotational springs in assessing the BRB's buckling. This model confirms that the BRB and the gusset's OOP buckling limit states could be coupled and must be evaluated together. By incorporating the flexural effects of the steel casing and the infilled grout, the proposed model satisfactorily predicts the OOP buckling of the first‐story BRB and gussets. These research results can be used for the implementation of BRBs in new RC frame constructions.     

防屈曲支撑的有限元模拟及滞回性能分析

结合防屈曲支撑拟静力实验的研究成果,本文采用有限元软件ABAQU S对其进行了数值模拟分析。在模拟过程中,应用金属Com b ine本构模型设置内芯钢板材料属性。该模型是对传统双线性本构模型的改进,模拟结果很好地符合了实验结果,同时验证了防屈曲支撑具有良好的减震耗能性能,其在轴向加载达到7倍屈服位移时,依然能保持良好的滞回特性。通过对模型中橡胶无粘结层的合理设置,研究了内芯钢板在失稳变形中无摩擦滑移与能量缓冲转化的形变特点。分析表明,当外包约束强度和刚度足够时,内芯钢板在受轴向压力时只发生多波微幅弯曲失稳;随着内芯钢材与外包有效约束间隙的增大,支撑的失稳波幅也随之增大,支撑承载力与耗能能力显著降低。     

Design and full‐scale experimental evaluation of a seismically endurant steel buckling‐restrained brace system

This paper presents the results of 12 full‐scale tests on buckling‐restrained brace (BRB) specimens. A simple‐to‐fabricate all‐steel encasing joined by high‐strength bolts was used as the buckling‐restrainer mechanism. Steel BRBs offer significant energy dissipation capability through nondeteriorating inelastic response of an internal ductile core. However, seismic performance of BRBs is characterized by interaction between several factors. In this experimental study, the effects of core‐restrainer interfacial condition, gap size, loading history, bolt spacing, and restraining capacity are evaluated. A simple hinge detail is introduced at the brace ends to reduce the flexural demand on the framing components. Tested specimens with bare steel contact surfaces exhibited satisfactory performance under the American Institute of Steel Construction qualification test protocol. The BRBs with friction‐control self‐adhesive polymer liners and a graphite‐based dry lubricant displayed larger cumulative inelastic ductility under large‐amplitude cyclic loading, exceeding current code minimum requirements. The BRB system is also examined under repeated fast‐rate seismic deformation history. This system showed significant ductility capacity and remarkable endurance under dynamic loading. Furthermore, performance is qualified under long‐duration loading history from subduction zone's megathrust type of earthquake. Predictable and stable performance of the proposed hinge detail was confirmed by the test results. Internally imposed normal thrust on the restrainer is measured using series of instrumented bolts. Weak‐ and strong‐axis buckling responses of the core are examined. Higher post‐yield stiffness was achieved when the latter governed, which could be advantageous to the overall seismic response of braced frames incorporating BRBs.     

Finite element analysis of an all-steel buckling-restrained brace

Typical all-steel buckling-restrained braces (BRBs) usually exhibit obvious local buckling, which is attributed to the lack of longitudinal restraint to the rectangle core plate. To address this issue, all-steel BRBs are proposed, in which two T-shaped steel plates are adopted as the minor restraint elements to restrain the core plate instead of infilled concrete or mortar. In order to investigate the factors that characterize the hysterical responses of this device, different finite element (FE) models are developed for the specific context. The FE models are developed based on nonlinear finite element software, which incorporate continuum (shell or brick) elements, large displacement, and deformation formulations. In these FE models, two different steel constitutive models are adopted to precisely reproduce the cyclic response of the BRB component. Meanwhile, comparisons between the numerical and experimental results are conducted to validate the effectiveness and accuracy of the robust FE model. The agreements between experimental observations and numerical predictions demonstrate that the FE method could be utilized for in depth parametric analysis. Furthermore, BRBs with detailed configurations can provide excellent hysteretic behavior and seismic performance through the optimal design process.

     

Out‐of‐plane stability assessment of buckling‐restrained braces including connections with chevron configuration

One of the key limit states of buckling‐restrained braces (BRBs) is global flexural buckling including the effects of the connections. The authors have previously proposed a unified explicit equation set for controlling the out‐of‐plane stability of BRBs based on bending‐moment transfer capacity at the restrainer ends. The proposed equation set is capable of estimating BRB stability for various connection stiffnesses, including initial out‐of‐plane drift effects. However, it is only valid for symmetrical end conditions, limiting application to the single diagonal configuration. In the chevron configuration, the out‐of‐plane stiffness in the two ends differs because of the rotation of the attached beam. In this study, the equation set is extended to BRBs with asymmetric end conditions, such as the chevron configuration. Cyclic loading tests of the chevron configuration with initial out‐of‐plane drifts are conducted, and the results are compared with the proposed equation set, which is formulated as a function of the normalized stiffness of the attached beam. © 2016 The Authors. Earthquake Engineering & Structural Dynamics published by John Wiley & Sons Ltd. © 2016 The Authors. Earthquake Engineering & Structural Dynamics published by John Wiley & Sons Ltd.