TRANSALP—Cross-line recording during the seismic reflection transect in the Eastern Alps

Cross-line recording formed a companion experiment of the TRANSALP seismic reflection transect through the Eastern Alps, conducted by partner institutions from Austria, Germany and Italy in three field campaigns in the period fall 1998 to fall 1999. Besides of the originally expected three-dimensional control for the north–south running main transect, additional information on seismic anisotropy and alternative images of crucial parts of the main transect could be gained.Conventionally processed sections along N–S running common-midpoint (CMP) binning lines confirm and strengthen the predominance of midcrustal reflective structures of the ‘Sub-Tauern-Ramp’ beneath and south of the Tauern Window. Velocity analysis of the first arrivals exhibit about 10% higher velocities in east–west propagating P-waves, compatible with texture-dominated rock anisotropy, recorded on cross-lines at the Tauern Window. Pre-stack depth migration of cross-line recordings shows dominant south dip of the Sub-Tauern-Ramp with easterly dip components and a sub-horizontal root zone of the Sub-Dolomites-Ramp.     

Orogenic structure of the Eastern Alps, Europe, from TRANSALP deep seismic reflection profiling

The TRANSALP Group, comprising of partner institutions from Italy, Austria and Germany, acquired data on a 340 km long deep seismic reflection line crossing the Eastern Alps between Munich and Venice. Although the field work was split into four campaigns, between fall 1998 and summer 2001, the project gathered for the first time a continuous profile across the Alps using consistent field acquisition and data processing parameters. These sections span the orogen itself, at its broadest width, as well as the editor Fred Davey and the two adjacent basins. Vibroseis and explosion data, complementary in their depth penetration and resolution characteristics, were obtained along with wide-angle and teleseismic data. The profile shows a bi-vergent asymmetric structure of the crust beneath the Alpine axis which reaches a maximum thickness of 55 km, and 80–100 km long transcrustal ramps, the southward dipping ‘Sub-Tauern-Ramp’ and the northward-dipping ‘Sub-Dolomites-Ramp’. Strongly reflective patterns of these ramps can be traced towards the north to the Inn Valley and towards the south to the Valsugana thrust belt, both of which show enhanced seismicity in the brittle upper crust. The seismic sections do not reveal any direct evidence for the presence of the Periadriatic Fault system, the presumed equivalent to the Insubric Line in the Western Alps. According to our new evolutionary model, the Sub-Tauern-Ramp is linked at depth with remnants of the subducted Penninic Ocean. The ‘crocodile’-type model describes an upper/lower crustal decoupling and wedging of both the European and the Adriatic–African continents.     

Shear wave splitting in the Eastern Alps observed at the TRANSALP network

Data from the temporary TRANSALP seismic network were analysed to investigate the seismic anisotropy in the upper mantle beneath the Eastern Alps. We operated mostly short period and some broadband stations in a dense linear array, which transects the Eastern Alps at 12° E longitude. Recorded SKS and SKKS phases with different backazimuths were used simultaneously to calculate the splitting parameters of delay time and fast axis direction for each seismic station. While we found variations in the delay times between 0.8 and 2.0 s, the determined fast axis directions prove to be rather consistent along the profile (60°–70° N). They coincide well with the trend of the Eastern Alps, thus suggesting orogen-parallel flow in the upper mantle. Our findings support the earlier proposed idea that the Adriatic indenter which was forced northwards into the European plate during the late stage of the Alpine orogeny, triggered an escape movement to the less constrained Pannonian basin to the east.     

Crustal structure of the Eastern Alps along the TRANSALP profile from wide-angle seismic tomography

The objective of the TRANSALP project is an investigation of the Eastern Alps with regard to their deep structure and dynamic evolution. The core of the project is a 340-km-long seismic profile at 12°E between Munich and Venice. This paper deals with the P-wave velocity distribution as derived from active source travel time tomography. Our database consists of Vibroseis and explosion seismic travel times recorded at up to 100 seismological stations distributed in a 30-km-wide corridor along the profile. In order to derive a velocity and reflector model, we simultaneously inverted refractions and reflections using a derivative of a damped least squares approach for local earthquake tomography. 8000 travel time picks from dense Vibroseis recordings provide the basis for high resolution in the upper crust. Explosion seismic wide-angle reflection travel times constrain both deeper crustal velocities and structure of the crust–mantle boundary with low resolution. In the resulting model, the Adriatic crust shows significantly higher P-wave velocities than the European crust. The European Moho is dipping south at an angle of 7°. The Adriatic Moho dips north with a gentle inclination at shallower depths. This geometry suggests S-directed subduction. Azimuthal variations of the first-break velocities as well as observations of shear wave splitting reveal strong anisotropy in the Tauern Window. We explain this finding by foliations and laminations generated by lateral extrusion. Based on the P-wave model we also localized almost 100 local earthquakes recorded during the 2-month acquisition campaign in 1999. Seismicity patterns in the North seem related to the Inn valley shear zone, and to thrusting of Austroalpine units over European basement. The alignment of deep seismicity in the Trento-Vicenza region with the top of the Adriatic lower crust corroborates the suggestion of a deep thrust fault in the Southern Alps.     

Experimental study of the seismic properties of the Eastern Alps (Italy) along the Aurina–Tures–Badia Valleys transect

In order to better constrain the interpretation and the nature of the seismic reflectors, experimental measurements at high confining pressure (up to 300 MPa) and room temperature of the compressional wave velocity (Vp) on 10 samples representative of the most common lithologies along the Aurina (Ahrntal), Tures (Tauferer Tal), and Badia (Abtei Tal) Valleys profile (Eastern Alps, Italy) have been performed. For each sample, the speed of ultrasonic waves was measured in three mutually perpendicular directions, parallel and normal to the rock foliation and lineation.The main results are:(a) Good agreement between the calculated vs. measured modal compositions of the considered rocks, indicating that they were presumably equilibrated at the estimated P–T conditions; therefore, the seismic properties are representative of the crustal level indicated by the thermobarometry.(b) Measured and calculated average Vp are in good agreement, and are typical of mid-crustal level (6.0–6.5 km/s). Only the amphibolites show Vp typical of the lower crust (7.2 km/s).(c) The seismic anisotropy of metapelites is very high (12–27%), both with orthorhombic and transverse isotropy symmetry; amphibolites are transversely isotropic with an anisotropy of 8%; orthogneisses and granitoids are isotropic or weakly anisotropic.(d) The contacts between amphibolites and all other rock types may generate good reflections, provided they are not steeply inclined. Although the metamorphic foliation remains steeply inclined, discordant buried sub-horizontal igneous contacts may be detected.     

A review of the thermal regime of the Eastern Alps with respect to the effects of paleoclimate and exhumation

Transient thermal signals such as Pleistocene surface temperature variations or exhumation of great rock volumes are important for the current thermal regime of the Eastern Alpine crust. In this study transient 1-D forward simulations and an analytical approach were used to estimate the order of magnitude of these effects. A comparison with numerical forward simulations and inverse analyses of steady-state heat conduction yields the following main conclusions with respect to the thermal regime of the Eastern Alps along the TRANSALP profile: (1) The change of surface temperatures in the past affects mainly the uppermost part of the Eastern Alpine crust. It results in a maximum thermal signature of more than − 6 K at a depth of 2 km. The deviations from a steady-state temperature gradient and heat flow in the region of the Tauern Window range from 0.3–4 K km^− 1 and 0–6 mW m^− 2, respectively, with maximum values at the surface. (2) Exhumation of the Eastern Alpine lithosphere may result in a thermal signature of up to 4 K at a depth of 1 km. The thermal signature increases further with depth to a maximum of approximately 80 K at a depth of 50 km. As the temperature gradient of the exhumation signal is almost zero at the base of the crust, Moho heat flow appears to be not critically perturbed. (3) The combined effect of exhumation and changing surface temperatures at the Tauern Window amounts to less than 15% of the steady-state temperatures at a depth of  8 km and to less than 10% at the base of Eastern Alpine root. The corresponding perturbation in heat flow is less than 20% at a depth of 4 km, approaching zero below 40 km.     

New gravity maps of the Eastern Alps and significance for the crustal structures

The deep seismic profile Transalp crosses, from north to south, Germany, Austria and Italy. The gravity measurements for each country were made by national agencies with different reference systems and data reduction methods. Within the frame of the Transalp-project a comprehensive database of the Eastern Alps was compiled covering an area of 3.5° by 4° in longitude and latitude (275 by 445 km), respectively. To increase the data coverage in the south Alpine area two gravity surveys were carried out, resulting in 469 areally distributed new stations, of which 215 have been measured with the intent to improve the geoid in the area of the planned Brenner Basistunnel (BBT). The resulting gravity database is the best in terms of resolution and data quality presently available for the Eastern Alps. Here the free air, Bouguer and isostatic gravity fields are critically discussed. The spatial density of existing gravity stations in the three countries is discussed. On the Italian side of the Alps the spatial density is rather sparse compared to the Austrian side. The Bouguer-gravity field varies between − 190 * 10^− 5 m/s² and + 25 * 10^− 5 m/s², with the minimum located along the Alpine high topographic chain, but with a small offset (a few tens of km) to the greatest topographic elevation, showing that the Airy-type local isostatic equilibrium does not fully apply here. The maximum of the Bouguer anomaly has an elongated shape of 100 by 50 km located between the towns of Verona and Vicenza and covers the Venetian Tertiary Volcanic Province (VTVP), a feature not directly related to the plate collision in the Eastern Alps. The gravity high is only partly explainable by high-density magmatic rocks and requires also a deeper source, like a shallowing of the Moho. The isostatic residual anomalies (Airy model) are in the range ± 50 * 10^− 5 m/s², with the greatest positive anomaly corresponding to the location of the VTVP, indicating here under-compensation of masses. At last a discussion of a 2D density model based on reflection seismic data and receiver functions is made.     

Prograde–retrograde P–T–t–deformation path of Austroalpine micaschists during Variscan continental collision (Eastern Alps)

A complete prograde P–T path, defined by 10 calculated P–T fields in succession, is recognized from metapelites by using geothermobarometry on garnet-bearing assemblages with microstructural control. Overstacking of several tectonic units during an early Variscan continental collision explains the complex prograde P–T history. Isostatic uplift and deformation controlled the retrograde P–T path. Deformation with changing character acted continuously during all stages of the evolution of the Austroalpine basement complex. After the intrusion of Caledonian granitoids, metapelites and magmatic rocks suffered a shearing deformation D₁–D₂, which produced sheath folds as well as the main foliation S₂. Spessartine-rich first-generation garnets, situated in microlithons enclosed by S₂, record the onset of shearing under increasing high-pressure–low-temperature conditions (7 kbar/380°C). Geothermobarometry on second-generation garnets which have been rotated during growth indicates isothermal decompression from 9 kbar to 5 kbar/500°C and subsequent recompression/heating during continuing shearing. This is explained by overthrusting of a tectonic unit (unit 2) from NE to SW upon the micaschist unit (unit 1), followed by isostatic uplift and further overstocking of a third unit (unit 3). The resulting P_max of 12 kbar at 650°C and further increasing temperatures up to 680°C accompanied by decompression have been calculated using a third generation of garnets. These high-pressure–high-temperature conditions may explain the occurrence of eclogitic metabasites in adjacent regions. Staurolite and kyanite first appeared under decreasing pressures at the last stage of prograde P–T evolution. Shortening deformation D₃ and simultaneous growth of typical amphibolite facies minerals (staurolite 2, kyanite 2, sillimanite, andalusite) occurred during the retrograde path. A final step of Variscan evolution was marked by an oppositely directed shearing D₄ (at T > 300°C and P > 3 kbar), possibly indicating backthrusting or extension. Apart from acid intrusions, no signs of a previous Caledonian thermotectonic history were found in the area to the south of the Defereggen–Antholz–Vals Line.     

The crustal structure of the Eastern Alps from a combination of 3D gravity modelling and isostatic investigations

The transition between European and Adriatic crust is an important feature related to the plate collision that formed the European Alps. The diversity of seismic and geological information allows the construction of two alternative 3D density models, which both match the observed gravity field. Different seismic experiments suggest a thickness for the Adriatic crust between 30 and 40 km. The thick crust model requires an unusually dense lower crust (>3050 kg/m³) to reproduce the observed Bouguer anomaly. To evaluate the two alternative models, the isostatic implications of the geometry and density distribution within both 3D models are investigated, using local (Airy) and regional (Vening Meinesz) isostasy.Airy isostatic investigations show that the Eastern Alps are not isostatically compensated and the residuals correlate strongly with exposed geological formations. Subsequently, subsurface loading is an important factor controlling isostatic processes. The different geometry and densities in the two 3D models imply different loading at the crust–mantle boundary. The subsurface loads calculated from the 3D density models were used to estimate regional isostasy by a convolution method. In general, small rigidity values (D<10×10²¹ Nm) are determined for the Eastern Alpine lithosphere. In the model with a 40-km-thick Adriatic crust, high flexural rigidities are inferred for the Adriatic plate (>100×10²¹ Nm), but these values are unusual for an active orogenic region. The results point to the interfingering of European and Adriatic crust that results in the squeezing of European crust between Adriatic crust and mantle with additional contamination by mantle material.     

VRANCEA99—the crustal structure beneath the southeastern Carpathians and the Moesian Platform from a seismic refraction profile in Romania

The VRANCEA99 seismic refraction experiment is part of an international and multidisciplinary project to study the intermediate depth earthquakes of the Eastern Carpathians in Romania. As part of the seismic experiment, a 300-km-long refraction profile was recorded between the cities of Bacau and Bucharest, traversing the Vrancea epicentral region in NNE–SSW direction.

The results deduced using forward and inverse ray trace modelling indicate a multi-layered crust. The sedimentary succession comprises two to four seismic layers of variable thickness and with velocities ranging from 2.0 to 5.8 km/s. The seismic basement coincides with a velocity step up to 5.9 km/s. Velocities in the upper crystalline crust are 5.9–6.2 km/s. An intra-crustal discontinuity at 18–31 km divides the crust into an upper and a lower layer. Velocities within the lower crust are 6.7–7.0 km/s. Strong wide-angle PmP reflections indicate the existence of a first-order Moho at a depth of 30 km near the southern end of the line and 41 km near the centre. Constraints on upper mantle seismic velocities (7.9 km/s) are provided by Pn arrival times from two shot points only. Within the upper mantle a low velocity zone is interpreted. Travel times of a PLP reflection define the bottom of this low velocity layer at a depth of 55 km. The velocity beneath this interface must be at least 8.5 km/s.

Geologic interpretation of the seismic data suggests that the Neogene tectonic convergence of the Eastern Carpathians resulted in thin-skinned shortening of the sedimentary cover and in thick-skinned shortening in the crystalline crust. On the autochthonous cover of the Moesian platform several blocks can be recognised which are characterised by different lithological compositions. This could indicate a pre-structuring of the platform at Mesozoic and/or Palaeozoic times with a probable active involvement of the Intramoesian and the Capidava–Ovidiu faults. Especially the Intramoesian fault is clearly recognisable on the refraction line. No clear indications of the important Trotus fault in the north of the profile could be found. In the central part of the seismic line a thinned lower crust and the low velocity zone in the uppermost mantle point to the possibility of crustal delamination and partial melting in the upper mantle.     

Local seismic hazard assessment in areas of weak to moderate seismicity—case study from Eastern Germany

Generally the seismic hazard of an area of interest is considered independent of time. However, its seismic risk or vulnerability, respectively, increases with the population and developing state of economy of the area. Therefore, many areas of moderate seismic hazard gain increasing importance with respect to seismic hazard and risk analysis. However, these areas mostly have a weak earthquake database, i.e., they are characterised by relative low seismicity and uncertain information concerning historical earthquakes. In a case study for Eastern Thuringia (Germany), acting as example for similar places in the world, seismic hazard is estimated using the probabilistic approach. Because of the lack of earthquakes occurring in the recent past, mainly historical earthquakes have to be used. But for these the actual earthquake sources or active faults, needed for the analysis, are imprecisely known. Therefore, the earthquake locations are represented by areal sources, a common practice. The definition of these sources is performed carefully, because their geometrical shape and size (apart from the earthquake occurrence model) influence the results significantly. Using analysis tools such as density maps of earthquake epicentres, seismic strain and energy release support this. Oversizing of areal sources leads to underestimation of seismic hazard and should therefore be avoided. Large location errors of historical earthquakes on the other hand are represented by several alternative areal sources with final superimposition of the different results. In a very similar way information known from macroseismic observations interpreted as source rather than as site effects are taken into account in order to achieve a seismic hazard assessment as realistic as possible. In very local cases the meaning of source effects exceeds those of site effects very likely. The influence of attenuation parameter variations on the result of estimated local seismic hazard is relatively low. Generally, the results obtained by the seismic hazard assessment coincide well with macroseismic observations from the thoroughly investigated largest earthquake in the region.     

Deep seismic reflection profiling in the Archaean northeastern Yilgarn Craton, Western Australia: implications for crustal architecture and mineral potential

Deep seismic reflection data across the Archaean Eastern Goldfields Province, northeastern Yilgarn Craton, Western Australia, have provided information on its crustal architecture and on several of its highly mineralised belts. The seismic reflection data allow interpretation of several prominent crustal scale features, including an eastward thickening of the crust, subdivision of the crust into three broad layers, the presence of a prominent east dip to the majority of the reflections and the interpretation of three east-dipping crustal-penetrating shear zones. These east-dipping shear zones are major structures that subdivide the region into four terranes. Major orogenic gold deposits in the Eastern Goldfields Province are spatially associated with these major structures. The Laverton Tectonic Zone, for example, is a highly mineralised corridor that contains several world-class gold deposits plus many smaller deposits. Other non crustal-penetrating structures within the area do not appear to be as well endowed metallogenically as the Laverton structure. The seismic reflection data have also imaged a series of low-angle shear zones within and beneath the granite–greenstone terranes. Where the low-angle shear zones intersect the major crustal-penetrating structures, a wedge shaped geometry is formed. This geometry forms a suitable fluid focusing wedge in which upward to subhorizontal moving fluids are focused and then distributed into the nearby complexly deformed greenstones.     

宽角反射、折射地震数据与重力数据综合解释龙门山及邻近地区地壳结构

青藏高原东部的隆升机制一直都是地学界的研究热点,研究学者们提出和发展了多种岩石圈变形模型,而存在多种模型的主要原因之一是对青藏高原东部地壳及岩石圈结构认识不足。本文主要针对SinoProbe-02项目横跨龙门山断裂带、全长400多公里的宽角、折射地震数据及重力数据进行联合反演和综合解释。研究结果表明,龙门山及邻近地区地壳结构可明确划分为上地壳、中地壳和下地壳。上地壳上层为沉积层,龙门山断裂带以西大部分区域被三叠纪复理岩覆盖,而在龙日坝断裂与岷江断裂之间出现了密度为2.7g/cm³的高速异常体;向东靠近龙门山地区,沉积层厚度逐渐减薄。中地壳速度变化不均一,而且变形强烈;若尔盖盆地和龙门山断裂带下方出现明显低速带;中地壳在龙门山西侧厚度加厚,在岷江断裂下方和四川盆地靠近龙门山断裂带地区附近厚度达到最大。莫霍面整体深度从东往西增厚,最厚可达56 km。本次研究得到的地壳结构和密度分布分析结果表明现有的地壳厚度和物质组成不足以支撑龙门山及邻近地区目前所达到的隆升高度,因此四川盆地刚性基底西缘因挤压作用产生的弯曲应力也是该地区抬升的重要条件之一。     

High‐resolution seismic reflection profiling of neotectonic faults in Lake Timiskaming,Timiskaming Graben,Ontario‐Quebec,Canada

The Timiskaming Graben is a 400 km long, 50 km wide north‐west trending morphotectonic depression within the Canadian Shield of eastern North America and experiences frequent intraplate earthquakes. The graben extends along the border of Ontario and Quebec, connecting southward with the Nipissing and Ottawa‐Bonnechere grabens and the St. Lawrence Rift System which includes a similar structure underlying the Hudson Valley of the eastern USA. Together they form a complex failed rift system related to regional extension of North American crust during the breakup of Rodinia and, later, Pangea. The Timiskaming Graben lies within a belt of heightened seismic activity (Western Quebec Seismic Zone) with frequent moderate magnitude (greater than magnitude 5) earthquakes including a magnitude 6.2 in 1935. These events threaten aging urban infrastructure built on soft glacial sediments; post‐glacial landslides along the Ottawa Valley suggest earthquakes as large as magnitude 7. The inner part of the Timiskaming Graben is filled by Lake Timiskaming, a large 110 km long post‐glacial successor to glacial Lake Barlow that was ponded by the Laurentide Ice Sheet 9500 years ago. The effects of frequent ground shaking on lake floor sediments was assessed by collecting more than 1000 line kilometres of high‐resolution ‘chirp’ seismic profiles. Late glacial Lake Barlow glaciolacustrine and overlying post‐glacial sediments are extensively deformed by extensional faults that define prominent horsts and grabens; multibeam bathymetry data suggest that faults influence the morphology of the modern lake floor, despite high sedimentation rates, and indicate recent neotectonic deformation. The Lake Timiskaming area provides evidence of post‐glacial intracratonic faulting related to recurring earthquake activity along a weak spot within the North American plate.     

Three-dimensional seismic modelling of crustal structure in the TESZ region based on POLONAISE''97 data

This paper reports the results of 3-D tomographic modelling of crustal structure in the Trans European Suture Zone region (TESZ) of Poland, eastern Germany and Lithuania. The data are the product of a large-scale seismic experiment POLONAISE'97, which was carried out in 1997. This experiment was designed to provide some 3-D coverage. The TESZ forms the boundary between the Precambrian crustal terranes of the East European Craton (EEC) and the younger Phanerozoic terranes to the southwest. The 3-D results generally confirm the earth models derived by earlier 2-D analyses, but also add some important details as well as a 3-D perspective on the structure. The velocity model obtained shows substantial horizontal variations of crustal structure across the study area. Seismic modelling shows low (<6.1 km/s) velocities suggesting the presence of sedimentary rocks down to a depth of about 20 km in the Polish basin. The shape of the basin in the vicinity of the profile P4 shows significant asymmetry. Three-dimensional modelling also allowed tracing of horizontal irregularities of the basin shape as well as variations of the Moho depth not only along profiles, but also between them. The slice between P2 and P4 profiles shows about 10-km variations of the Moho over a 100-km interval. The crustal thickness varies from about 30 km in SW, beneath the Palaeozoic platform, to about 42 km beneath East European Craton in NE. High seismic velocities of about 6.6 km/s were found in the depth range 2–10 km, which coincides with K trzyn anorthosite massif. The results of this 3-D seismic modelling of the POLONAISE'97 data will ultimately be supplemented by inversion of seismic data from previous experiments.     

Seismic image of the deep crust at the eastern margin of the Alps (Austria): indications for crustal extension in a convergent orogen

A 39-km-long deep seismic reflection profile recorded during two field campaigns in 1996 and 2002 provides a first detailed image of the deep crust at the eastern margin of the Eastern Alps (Austria). The ESE–WNW-trending, low-fold seismic line crosses Austroalpine basement units and extends approximately from 20 km west of the Penninic window group of Rechnitz to 60 km SSE of the Alpine thrust front.The explosive-source seismic data reveals a transparent shallow crust down to 5 km depth, a complexly reflective upper crust and a highly reflective lowermost crust. The upper crust is dominated by three prominent west-dipping packages of high-amplitude subparallel reflections. The upper two of these prominent packages commence at the eastern end of the profile at about 5 and 10 km depth and are interpreted as low-angle normal shear zones related to the Miocene exhumation of the Rechnitz metamorphic core complex. In the western portion of the upper crust, east-dipping and less significant reflections prevail. The lowermost package of these reflections is suggested to represent the overall top of the European crystalline basement.Along the western portion of the line, the lower crust is characterised by a 6–8-km-thick band of high-amplitude reflection lamellae, typically observed in extensional provinces. The Moho can be clearly defined at the base of this band, at approximately 32.5 km depth. Due to insufficient signal penetration, outstanding reflections are missing in the central and eastern portion of the lower crust. We speculate that the result of accompanying gravity measurements and lower crustal sporadic reflections can be interpreted as an indication for a shallower Moho in the east, preferable at about 30.5 km depth.The high reflectivity of the lowermost part of the lower crust and prominent reflection packages in the upper crust, the latter interpreted to represent broad extensional mylonite zones, emphasises the latest extensional processes in accordance with eastward extrusion.     

Structural fabric of the Central Metasedimentary Belt of southern Ontario, Canada, from deep seismic profiling

The Central Metasedimentary Belt boundary tectonic zone (CMBbtz) is a 10–20-km-wide zone of intense structural deformation within the 1.3–1.0 Ga Grenville orogen of southeastern Canada. The crustal structure of the exposed CMBbtz has been well studied, but its sub-Phanerozoic location and geometry beneath the urban development and nuclear stations of the Toronto region are not well known. A new 75-km Lithoprobe reflection profile acquired close to Toronto provides a clear image of the CMBbtz as a panel of southeast-dipping reflections that extends with moderate dip (<25°) to mid-crustal depth (25 km). These dipping reflections truncate and (or) overprint a subhorizontal band of reflectivity at 21 km depth. The seismic line is oblique to the major structural trends; cross-dip analysis shows that the southeast-dipping reflections have a strike and dip of N13°E and 25°, whereas the “subhorizontal” reflections strike and dip at N65°E and 20°, respectively. Both of these bands of reflectivity can be correlated to magnetic anomalies in the CMBbtz or its immediate footwall. Magnetic anomalies with similar strike directions are well expressed within a distinct rhomboid-shaped region (106×109 km) in the subsurface of western Lake Ontario, herein named Mississauga domain. Taken together, the seismic and magnetic data are inconsistent with existing models, in which the CMBbtz is extrapolated beneath Lake Ontario along a linear magnetic anomaly. We propose a revised subsurface trace of the CMBbtz along the western edge of the Mississauga domain. Small earthquakes in western Lake Ontario appear to cluster along trends co-linear with ENE magnetic anomalies, suggesting a possible degree of basement tectonic control on local intraplate seismicity.     

Variable post-Paleozoic deformation detected by seismic reflection profiling across the northwestern “prong” of New Madrid seismic zone

High-resolution shallow seismic reflection profiles across the northwesternmost part of the New Madrid seismic zone (NMSZ) and northwestern margin of the Reelfoot rift, near the confluence of the Ohio and Mississippi Rivers in the northern Mississippi embayment, reveal intense structural deformation that apparently took place during the late Paleozoic and/or Mesozoic up to near the end of the Cretaceous Period. The seismic profiles were sited on both sides of the northeast-trending Olmsted fault, defined by varying elevations of the top of Mississippian (locally base of Cretaceous) bedrock. The trend of this fault is close to and parallel with an unusually straight segment of the Ohio River and is approximately on trend with the westernmost of two groups of northeast-aligned epicenters (“prongs”) in the NMSZ. Initially suspected on the basis of pre-existing borehole data, the deformation along the fault has been confirmed by four seismic reflection profiles, combined with some new information from drilling. The new data reveal (1) many high-angle normal and reverse faults expressed as narrow grabens and anticlines (suggesting both extensional and compressional regimes) that involved the largest displacements during the late Cretaceous (McNairy); (2) a different style of deformation involving probably more horizontal displacements (i.e., thrusting) that occurred at the end of this phase near the end of McNairy deposition, with some fault offsets of Paleocene and younger units; (3) zones of steeply dipping faults that bound chaotic blocks similar to that observed previously from the nearby Commerce geophysical lineament (CGL); and (4) complex internal deformation stratigraphically restricted to the McNairy, suggestive of major sediment liquefaction or landsliding. Our results thus confirm the prevalence of complex Cretaceous deformations continuing up into Tertiary strata near the northern terminus of the NMSZ.     

深水区地震波传播特性研究

根据层速度与Q值的经验公式和对射线参数进行泰勒展开的方法，以及二维有限差分声波波动方程波场数值模拟技术，为海上长排列大容量震源地震资料采集及高分辨率地震勘探野外施工的观测系统设计及数据处理方案等提供参考意见。     

Complexity of seismic process; measuring and applications — A review

Recent methods of analysis of so called disordered systems show that many objects and processes that earlier were considered as completely random reveal clear evidence of having some ordered structure in both time and space. These new methods (fractals, percolation, nonlinear dynamics and complexity theories) allow visualization and quantitative assessment of the level of complexity (orderliness) of these structures, using both theoretical models and experimental data. We consider sequentially some aspects of structural and evolutionary complexity of dynamics of seismic process and the technique of measuring this property.It is shown that the physical properties of geophysical medium are not always self-consistent and manifest fractal behavior on selected spatial and temporal scales. Mechanical percolation theory can be used for modeling geometry of fracture process. Namely, we consider fractal and connectivity aspects of delayed failure, including energy emission during fracturing. Special attention is paid to relating the intensity of geophysical anomalies to the strain in the framework of the pressure-induced anomalous strain-sensitivity (percolation) model, which explains naturally the observed heterogeneity of response of a geophysical media to the strain variation.Different methods of measuring the dynamic complexity of seismological time series are applied to magnitude and waiting time sequences of Caucasian earthquakes. The fractal (correlation) dimension d₂ of the latter is high (larger than 8), but the former one has as low dimension as 1.6–2.5, which makes waiting time sequences a promising tool for revealing precursory changes.The same nonlinear technique allow detecting significant changes in the seismic regime during external electromagnetic forcing by MHD pulses; similar tests on the laboratory scale show the possibility of triggering/controlling stick-slip process by relatively weak electromagnetic or mechanical forcing.Lastly, the predictive potential of complexity analysis of seismological time series is considered. For example, percolation model predicts the increase of the number of large events and the scatter of magnitudes of events, decrease of the magnitude-frequency relation slope and appearance of multifractality at approaching the final rupture.It seems that seismology can benefit from using the new techniques to cope with the complexity of earthquake machine; for example, the measures of complexity can be characteristic for a given region and change before strong earthquake.