岩体中节理面、软弱夹层等的力学性质和模拟分析方法(续)

六、滑移条件的实验依据和节理单元的塑性变形问题采用关联流动理论来推导节理单元的弹塑性物性矩阵可以明显看出它将使处于继续加载状态的单元的新应力点将落在残余强度线上,也就是说是满足“滑移条件”的,但这与实验结果是否接近呢? 现在我们列举一九七○年在某矿区所作的野外剪切“单点法”试验结果以资说明.     

基于结构面性状对岩体力学性质响应的模拟研究

为研究结构面性状对锦屏大奔流料场边坡岩体性质的影响,在对该边坡砂岩进行室内三轴压缩试验的基础上,开展含4组不同结构面性状岩体的力学模拟测试,最后对该边坡岩体的开挖进行数值模拟。试验结果表明,岩样破坏过程可以分为4个典型的阶段: 弹性变形阶段,屈服阶段,残余强度阶段及塑性流动阶段。随着围压的增大,岩石破坏所需偏应力逐渐增大,且岩石逐渐表现出延性特征。结构面性状模拟结果表明,含软弱充填结构面比不含者对岩体力学性质影响(弱化)大,有倾角结构面比无倾角结构面对岩体性质影响较大,大倾角结构面总体上比小倾角的影响大,软弱充填厚度对岩体内摩擦角影响较大。实例模拟结果表明,开挖卸荷使得边坡后缘岩体产生卸荷回弹变形,产生X向拉伸位移,煌斑岩脉的存在使得塑性区域沿此软弱带发展,开挖第8步时,塑性区贯通,边坡发生失稳。研究结果对陡高边坡岩体开挖的稳定性评价具有一定指导意义。     

法向压力对岩体抗剪力学特性的影响

法向压力直接影响着岩体的抗剪力学特性．目前的岩石抗剪试验．对法向力的选取没有明确的规定．导致测试结果极容易出现因人而异的现象．作者针对这种状况．对完整岩块、结构面和软弱夹层三种类型分别提出直剪试验法向压力的确定原则．     

The Mechanical. Behaviors and Analog Analytical Method of Joints and Weak Intercalations in Rock Mass

In this paper, the mechanical behaviors of rock joints and internationals etc. are described. According to the filed results of the shear tests, several basic types of shear displacement are discussed and classified。 based on the nonlinear properties of these weak plants ,the analytical models and methods suggested in this paper, the influence of normal stress on the shear deformation may be considered .It also can be applied to the complicated conditions of loading-unloading-reloadings. The non-linear and the problems of the weak plane’s reclosing after opening can be handled simultaneously. The same analytical method is also acceptable to the shear deformation properties of various types only by choosing different parameters. Wish this analytical method, analogic calculations for the in-situ weak-plane shear tests are made and results are well checked by curves .This method has been used in some practical engineering problems .     

The Mechanical. Behaviors and Analog Analytical Method of Joints and Weak Intercalations in Rock Mass (Continued)

In this paper, the mechanical behaviors of rock joints and internationals etc. are described. According to the filed results of the shear tests, several basic types of shear displacement are discussed and classified。 based on the nonlinear properties of these weak plants ,the analytical models and methods suggested in this paper, the influence of normal stress on the shear deformation may be considered .It also can be applied to the complicated conditions of loading-unloading-reloadings. The non-linear and the problems of the weak plane’s reclosing after opening can be handled simultaneously. The same analytical method is also acceptable to the shear deformation properties of various types only by choosing different parameters. Wish this analytical method, analogic calculations for the in-situ weak-plane shear tests are made and results are well checked by curves .This method has been used in some practical engineering problems .     

组合节理面抗剪力学特性的模型试验研究

本文研究了处于同一平面上的两组性能各异、交替出现的子节理面所组成的组合节理面的抗剪力学性质。通过对脆—脆、脆—塑、塑—塑三种类型的组合节理面的模型抗剪试验,得出了组合节理面的抗剪强度与各单体(又称子节理面)材料在组合节理面上所占的面积、单体交替出现的次数及抗剪方向等之间的关系。这些结论在实际工程应用方面有着非常重要的意义。     

变形岩体软弱破裂带的处理技术

在研究完成变形岩体软弱破裂带可灌性的基础上,采用旋喷注浆技术进行直接加固处理,提高破裂带的内聚力和内摩擦角,实践证明,抑制了岩体的变表,防止了滑坡的产生。     

葛洲坝泥化夹层的物质组成特性

葛溯坝基岩中,砂岩或粉砂岩岩层间夹有一些厚薄不等,性状各异的粘土岩或粉砂质粘土岩,以及它们的泥化夹层等软弱夹层。本文主要是根据若干典型夹层的矿物成分及其定量分析结果和部分颗粒分析资料等,叙述和讨论了软弱岩层的物质组成,特别是亲水性粘土矿物的组成特性与泥化夹层形成的关系。     

Experimental Study of Mechanical Behaviour of Rock Joints Under Cyclic Loading

Summary Evaluation of the effects of small repetitive earthquakes on the strength parameters of rock joints in active seismic zones is of interest of the designers of underground constructions. In order to evaluate these effects, it is necessary to study the behaviour of rock joints under dynamic and cyclic loadings. This paper presents the results of a systematic study on the behaviour of artificial rock joints subjected to cyclic shearing. More than 30 identical replicas have been tested using triaxial compression devices under different conditions of monotonic and cyclic loading. At the first stage a few samples have been tested in monotonic loading modes under various confining pressures and rate of displacement. In the second series of tests, small cyclic loads were applied on the samples for increasing number of cycles, frequency levels and stress amplitudes. These were then followed by monotonic loading again. The variations of maximum and residual shear strengths for each test have been studied. The results show increase of shear strength as a result of the increase in confining pressure and they display decrease of shear strength due to the increase of rate of loading, number of cycles, frequency levels and stress amplitudes.     

The Planar Shape of Rock Joints

Knowing the planar shape of discontinuities is important when characterizing discontinuities in a rock mass. However, the real discontinuity shape is rarely known, since the rock mass is usually inaccessible in three dimensions. Information on discontinuity shape is limited and often open to more than one interpretation. This paper discusses the planar shape of rock joints, the most common discontinuities in rock. First, a brief literature review about the shape of joints is presented, including some information on joint-surface morphology, inferences from observed trace lengths on different sampling planes, information based on experimental studies, and joint shapes assumed by different researchers. This review shows that joints not affected by adjacent geological structures such as bedding boundaries or pre-existing fractures tend to be elliptical (or approximately circular but rarely). Joints affected by or intersecting such geological structures tend to be rectangular. Then, using the general stereological relationship between trace length distributions and joint size distributions developed by Zhang et al. (Geotechnique 52(6):419–433, 2002) for elliptical joints, the effect of sampling plane orientation on trace lengths is investigated. This study explains why the average trace lengths of non-equidimensional (elliptical or similar polygonal) joints on two sampling planes can be about equal and thus the conclusion that rock joints are equidimensional (circular) drawn from the fact that the average trace lengths on two sampling planes are approximately equal can be wrong. Finally, methods for characterizing the shape and size of joints (elliptical or rectangular) from trace length data are recommended, and the appropriateness of using elliptical joint shapes to represent polygonal, especially rectangular, joints is discussed.     

Application of Rock Mass Characterization for Determining the Mechanical Properties of Rock Mass: a Comparative Study

The results of geotechnical explorations, engineering geological investigation (including laboratory and in situ tests) and field observations have been used, along with borehole logging charts, to obtain the rock mass geotechnical data. Based on the data, the rock mass along the Sabzkuh water conveyance tunnel route was classified by rock mass rating (RMR), Q-system (Q), rock mass index (RMi) and geological strength index (GSI) (3 methods). A new series of correlations were established between the systems based on the data collected from the study area. These relationships were then compared with those reported in the literature, and two new relations were recommended. The classifications were utilized to calculate mechanical properties (rock mass strength and deformation modulus) of the rock mass along the tunnel according to available empirical relations, and to distinguish the upper-bound and lower-bound relations.