南京地区新近沉积土的动剪切模量和阻尼比的初步研究

本文通过对南京地区两个工程场地漫滩相成因的砂土和淤泥质粉粘土与粉砂互层土的自振动柱试验结果进行分析，探讨了围压对剪切模量G及阻力比λ的影响，通过与Seed和Idriss建议的砂土G/Gmax-γ和λ-γ曲线变化范围的对比，认为不能简单地把淤泥质粉质粘土与粉砂层土当作砂土或粉质粘土对待。     

固结比对土最大动剪切模量的影响

采用共振柱试验方法,研究了固结比对土最大动剪切模量的影响并给出了土最大动剪切模量的建议公式。通过对砂土、粉质黏土和粉土的系统试验,提出了不同固结比下土最大动剪切模量与固结比kc-1呈指数形式的增长模式,不同于Hard in公式最大动剪切模量与固结比kc呈直线形式的增长模式。同时给出了计算不同固结比下砂土、粉质黏土和粉土最大动剪切模量的建议公式,并与Hard in公式进行了对比,结果表明,固结比对土最大动剪切模量影响程度明显比Hard in公式要大,固结比对粉质黏土和粉土最大动剪切模量的影响程度要比对砂土的影响程度更大。     

常规土类动剪切模量比和阻尼比试验研究

采用共振柱自振试验方法给出国内常规土类动剪切模量比G／Gmax和阻尼比λ变化的平均曲线,推荐值和包线,使用的共振仪是由工种力学研究所原有共振柱改装而成,并经试验验证了改装后仪器的精度可靠性,试验土类包括粘土,粉质土,粉土,砂土,淤泥和淤泥质土,土样来自国内十余个不同地区,采用折线双曲线拟合G／Gmax,λ随γ衰减关系,其中参数a和b由最小二乘法对每次试验结果回归分析得到,对同类土,将所有的a,b 值平均,用均值a和b给出动剪切模量比和阻尼比与剪应变关系,从而得到了此类土G/Gmax,λ随γ变化曲线及推荐值,试验是在两种固结压力下进行,因而得到的结构分别适用于土体埋深小于10m和埋深10m-20m之间的两种情况。     

山西黄土动剪切模量与阻尼比试验研究

土的动剪切模量与阻尼比作为土动力特性研究的重要参数,一直备受关注。为了研究山西地区黄土的动力特性,对山西某土石坝坝基黄土进行了共振柱与动三轴试验,获得了在较大应变范围内的动剪切模量与阻尼比试验数据。试验结果表明,山西黄土动剪切模量与阻尼比均显著受初始含水率影响,其归一化的动剪切模量能够用修正的Hardin模型进行拟合,并给出了相关参数;阻尼比可以采用本文建议的公式进行拟合,拟合效果良好。最后,采用经验公式确定了不同围压下的最大动剪切模量的参数。     

饱和砂土最大动剪切模量的不同试验对比研究

对233个饱和砂土土样室内试验确定的最大动剪切模量和同一位置现场原位试验确定的最大动剪切模量进行了对比研究。结果表明：两者相差很大,室内试验结果基本上小于现场试验结果,埋藏深的土样相差更大;室内试验的最大动剪切模量与深度符合幂函数规律,且与砂土的密实度有关,与砂土的颗粒成分关系不大。通过工程实例,比较了2种试验最大动剪切模量对地震反应分析的影响,得到了室内试验最大动剪切模量与现场剪切波速的统计经验关系式。该经验关系式对工程场地地震反应分析具有一定的参考应用价值。     

南京细砂动剪切模量和阻尼比的试验研究

动剪切模量和阻尼比是重大工程开展场地地震反应分析必不可少的参数。完成了南京细砂的自振柱和动三轴试验,研究了固结围压、孔隙比、含水量和荷载频率对动剪切模量和阻尼比的影响。试验结果表明:固结围压和孔隙比对最大动剪切模量的影响显著,建立了最大剪切模量与固结围压、孔隙比之间的经验关系,最大剪切模量随细砂中含水量的增加而减小并趋于稳定;固结围压对动剪切模量比具有一定影响,其他3个因素对动剪切模量比和阻尼比的影响不明显;排水条件下泊松比随剪应变幅值的增大而增大,剪应变幅值在1.0×10-4~1.0×10-3范围时,泊松比增大的趋势更加明显;采用自振柱和动三轴试验测试得到的动剪切模量比和阻尼比基本一致。     

西安地区典型土动剪切模量比和阻尼比的统计研究

利用西安市地震小区划项目中的大量典型土样动三轴试验结果,采用双曲线模型拟合得到了西安地区粉质粘土、粉土、砂土和卵砾土的动剪切模量比和阻尼比随剪应变的变化关系,给出了西安地区上述4种主要土壤类型在8个典型应变下的动参数值。所提结果对研究西安地区地基振动反应和场地地震安全性评价等工作具有参考和借鉴作用。     

相对密实度对含黏粒砂土动剪切模量与阻尼比影响的试验研究

利用GCTS共振柱系统开展一系列含黏粒砂土的动力特性试验,研究相对密实度对含黏粒砂土动剪切模量和阻尼比的影响,并探讨其影响规律.试验结果表明:相对密实度对动剪切模量、动剪切模量比、阻尼比、最大动剪切模量均有影响.动剪切模量随着相对密实度的增加而变大,但动剪切模量增大的幅度更大;当黏粒含量较小时,动剪切模量比随相对密实度...     

福建漳州地区典型土动力特性的试验研究

通过对福建漳州地区淤泥、粉质粘土、粉质粘土与粉砂互层土、残积土等4类典型土的共振柱试验,探讨了围压大小、土的性质对这4类典型土的动剪切模量G及阻尼比γ的影响,给出了在不同围压下的G/Gmax和λ/λmax随γ变化的平均曲线及其参数的推荐值,并定量的给出围压对参数的影响规律。结果对实际工程具有一定的借鉴作用。     

Dynamic shear modulus of undisturbed soil under different consolidation ratios and its effects on surface ground motion

The dynamic shear modulus for three types of undisturbed soil under different consolidation ratios is presented by using the resonant column test method. Its effects on surface ground motion is illustrated by calculation. The test results indicate that the power function is a suitable form for describing the relationship between the ratio of the maximum dynamic shear modulus due to anisotropic and isotropic consolidations and the increment of the consolidation ratio. When compared to sand, the increment of the maximum dynamic shear modulus for undisturbed soil due to anisotropic consolidation is much larger. Using a one-dimensional equivalent linearization method, the earthquake influence factor and the characteristic period of the surface acceleration are calculated for two soil layers subjected to several typical earthquake waves. The calculated results show that the difference in nonlinear properties due to different consolidation ratios is generally not very notable, but the degree of its influence on the surface acceleration spectrum is remarkable for the occurrence of strong earthquakes. When compared to isotropic consolidation, the consideration of actual anisotropic consolidation causes the characteristic period to decrease and the earthquake influence factor to increase.     

土体动剪切模量及其衰减特性现场试验研究

如何获取土体动模量原位衰减曲线是研究天然土层在循环动荷载下的动变形特性课题中亟待解决的难题。为此,本文自制了一套地震动参数现场试验系统,依据动剪切模量原位测试原理获得了不同深度土体在小应变范围内的动模量原位衰减曲线。试验数据表明:当剪应变小于4×10^－5时,土体变形处于线性阶段;当剪应变大于4×10^－5时,土体归一化动剪切模量G/G_max衰减加快,以塑性变形为主。同时,当向土层施加的垂向静荷载越大,归一化动剪切模量值G/G_max与对数剪应变值logγ_d之间的关系会逐渐上移,但直线段斜率值不变。相关成果可为试验场地的动模量取值提供一定参考。     

Effect of consolidation ratios on maximum dynamic shear modulus of sands

The dynamic shear modulus (DSM) is the most basic soil parameter in earthquake or other dynamic loading conditions and can be obtained through testing in the field or in the laboratory. The effect of consolidation ratios on the maximum DSM for two types of sand is investigated by using resonant column tests. And, an increment formula to obtain the maximum DSM for cases of consolidation ratio κc>1 is presented. The results indicate that the maximum DSM rises rapidly when κc is near 1 and then slows down, which means that the power function of the consolidation ratio increment κc-1 can be used to describe the variation of the maximum DSM due to κc>1. The results also indicate that the increase in the maximum DSM due to κc>1 is significantly larger than that predicted by Hardin and Black's formula.     

A Modified approach for calculating dynamic shear modulus of stiff specimens by resonant column tests

1 Introduction Study of the shear modulus to represent the static and dynamic properties of geotechnical materials is a basic topic in the geotechnical engineering and many researchers (Hardin and Black, 1966; Zhang and Li, 2003; Richard and Richard, 1988; Yuan et al, 2000; Soo et al, 1995) have investigated this phenomenon. The resonant column device provides a powerful tool for testing the shear modulus and damping ratio of the soil-like materials. In 1984, the ?rst resonant column device…     

动荷载作用下饱和砂土动剪模量试验研究

在50kPa、100kPa和200kPa 3种固结压力下分别对饱和度为95%、92%、88%和83%的土样进行了循环单剪试验,得到了该土样在4种饱和度、3种固结压力下的最大动剪模量Gdmax以及动剪模量比G/Gdmax-γ归一化曲线。分析得出,同一固结压力下土样的Gdmax和G/Gdmax随着饱和度的增大相对减小;随着固结压力的增大,两者数值上差异逐渐减小。最后对此种现象进行了讨论并分析了其产生的原因。     

青藏铁路重塑冻结粉质黏土动剪切模量试验研究

通过低温动三轴试验,研究青藏铁路中重塑冻结粉质黏土的动剪切模量的变化规律及其主要因素。研究表明,冻土的最大动剪切模量随负温降低而显著增大,动剪切模量比随轴向荷载单级振次增加而有所增大,随负温降低而降低,随围压增加趋于一致。负温是冻土动力性能的一个极其重要的影响因素,因而寒区工程应引起足够的重视。研究结果对于合理认识冻土动力性能具有一定意义,也为进一步开展多年冻土场地工程地震安全性评价积累部分基础资料。     

Effects of fabric anisotropy on elastic shear modulus of granular soils

The fabric anisotropy of a granular soil deposit can strongly infl uence its engineering properties and behavior. This paper presents the results of a novel experimental study designed to examine the effects of fabric anisotropy on smallstrain stiffness and its evolution with loading on the elastic shear modulus of granular materials under a K0 condition. Two primary categories of fabric anisotropy, i.e., deposition-induced and particle shape-induced, are investigated. Toyoura sand deposits with relative densities of 40% and 80% were prepared using deposition angles oriented at 0o and 90o. Piezoelectric transducers were used to obtain the elastic shear modulus in the vertical and horizontal directions(Gvh and Ghh). The measurements indicate distinct differences in the values of G with respect to the different deposition angles. Particle shapeinduced fabric anisotropy was examined using four selected sands. It was concluded that sphericity is a controlling factor dominating the small-strain stiffness of granular materials. The degree of fabric anisotropy proves to be a good indicatorin the characterization of stress-induced fabric evolution during loading and unloading stress cycles. The experimental data were used to calibrate an existing micromechanical model, which was able to represent the behavior of the granular material and the degree of fabric anisotropy reasonably well.