波浪荷载作用下砂土变形特性的模拟试验研究

利用新研制的“土工静力-动力液压三轴-扭转多功能剪切仪”模拟波浪荷载作用，对福建标准砂进行了4组三轴一扭转耦合振动剪切试验，以研究海床砂土在波浪荷载作用下的变形特性及其对砂土初始密度和固结压力的依赖性。试验结果表明，应力-应变呈现出良好的双曲线关系，与等效线性模型理论相吻合；阻尼比和模量随应变幅值的变化规律均依赖于土体的初始密度和固结压力；归一化后的E／Emax-ε及G／Gmax-γ曲线对相对密度和固结压力仍具有明显的依赖性；但完全归一化后的E／Emax-ε/εr及G／Gmax-γ/γr的关系曲线则与固结压力无关。     

不同地区黄土阻尼比变化特性试验研究

通过兰州、洛川、杨凌地区黄土在不同条件下的动扭剪三轴试验,研究了黄土阻尼比滞回圈形状变化的基本特性以及黄土阻尼比在不同固结压力、不同含水率条件下的变化规律。结果表明,黄土阻尼比滞回圈形状受动剪应变、含水率影响较明显;黄土阻尼比受一般的固结作用的影响并不大,但受含水率的影响较明显。根据含水率的不同,按照半对数坐标中的直线方程,分别给出了兰州、洛川、杨凌地区黄土阻尼比在不同固结压力下的拟合结果,并对拟合结果进行了对比分析;在此基础上,进一步对该三个地区黄土的阻尼比进行了汇总拟合,为西北相近地区黄土在中、大应变条件下的阻尼比取值提供了参考。     

陕北榆林地区 砂土动剪切模量比和阻尼比的统计研究

陕北榆林地区位于鄂尔多斯地块内部,其沉积地层主要为细砂。基于该地区大量的工程场地地震安全性评价报告,本文共收集了83组砂样动三轴试验数据,并分类统计分析了松散~稍密、中密和密实三种密实程度的砂土在8个典型剪应变下的动剪切模量比和阻尼比统计值。选取一个典型钻孔,建立土层地震反应模型,分别以本文"统计值"、"规范值"和"推荐值"作为模型参数进行土层地震反应计算,并对反应得到的地面峰值加速度与反应谱进行了对比分析。     

High strain dynamic modulus and damping of chemically grouted sand

Laboratory resonant column and cyclic triaxial tests are performed to determine the dynamic response (i.e. shear modulus and damping) of chemically grouted sand. The effect of chemical grouting is evaluated as a function of shearing-strain amplitude, confining stress, cycling prestrain, number of cycles, grout type, concentration, and curing time. The test results show that the shearing-strain amplitude, grout type and grout concentration have significant effects on the shear modulus and damping ratio of the test specimens. The increased addition of sodium silicate grout, which produces stiff gels, improved the shear modulus of the test sand. The acrylate (AC-400) and polyurethane (CG5610) grout, which produces flexible (rubber-like) gels, improved the damping capacity of the sand with increasing grout concentration. The addition of chemical grout greatly reduces the effect of cyclic prestraining over untreated sands. In the case of dense sands, the reduction of cyclic prestraining is less pronounced than in loose sands, which have a higher potential for particle movement and reorientation.     

南京地区新近沉积土的动剪切模量和阻尼比的初步研究

本文通过对南京地区两个工程场地漫滩相成因的砂土和淤泥质粉粘土与粉砂互层土的自振动柱试验结果进行分析，探讨了围压对剪切模量G及阻力比λ的影响，通过与Seed和Idriss建议的砂土G/Gmax-γ和λ-γ曲线变化范围的对比，认为不能简单地把淤泥质粉质粘土与粉砂层土当作砂土或粉质粘土对待。     

动荷载作用下土阻尼比的试验对比研究

本文对一粉质粘土,在100kPa、200kPa、300kPa 3种固结压力下,分别进行了原状土样的循环单剪试验、扰动土样的动三轴试验,得到了该粉质粘土2种土样、3种固结压力下的D/Ddm ax-γ曲线。试验结果表明,由循环单剪试验得到的原状土的D/Ddm ax-γ曲线与扰动土样的动三轴试验结果D/Ddm ax-γ曲线有一定差异,且随着固结压力的不同而变化。     

Estimation of damping ratio of soil sites using microtremor

It is widely known that the seismic response characteristics of a soil site depends heavily on several key dynamic properties of the soil stratum, such as predominant frequency and damping ratio. A widely used method for estimating the predominant frequency of a soil site by using microtremor records, proposed by Nakamura, is investigated to determine its effectiveness in estimating the damping ratio. The authors conducted some microtremor measurements of soil sites in Hong Kong and found that Nakamura’s method might also be used to estimate the damping ratio of a soil site. Damping ratio data from several typical soil sites were obtained from both Nakamura’s ratio curves using the half power point method and resonant column tests. Regression analysis indicates that there is a strong correlation between the damping ratios derived from these two different approaches. Supported by: Research project (PolyU 5076/97E), of the Department of Civil and Structural Engineering, The Hong Kong Polytechnic University     

钢筋混凝土建筑非线性阻尼性能及阻尼比表达式研究

阻尼比是反映结构耗能能力的参数，它对结构的振动反应有重要的影响。目前结构设计阶段通常取阻尼比为常数，这不能真实反映建筑物的阻尼机理，与阻尼比的实测结果也有很大的差距。通过对建筑物阻尼机理、建筑材料、建筑物和建筑模型阻尼性能试验数据的分析，本文对混凝土强度、纵向配筋率、结构形式和结构变形大小等建筑阻尼性能的主要影响因素进行了分析。在此基础上，本文提出了钢筋混凝土结构非线性阻尼比的统一表达式。     

Shear modulus and damping ratio of grouted sand

An experimental comparative study of three different grouted sands in terms of their effects on the values of two dynamic properties is presented. The dynamic properties studied are the shear modulus and the damping ratio which are determined with resonant column tests and cyclic triaxial tests. The behaviour of a pure Fontainebleau sand is compared with the behaviour of a Fontainebleau sand grouted with a silicate grout, a micro-fine cement grout and a mineral grout. The effects of the grouting treatment, the type of grout, the confining pressure, and the strains, on the shear modulus and the damping ratio are studied. The test results have shown that grouting improves the stiffness of the sand especially for small strains. Whatever the type of material, confining stress improves the shear modulus whereas it has a negligible effect on the damping ratio. When strain increases, the shear modulus decreases and the damping ratio increases.     

复阻尼振动方程频域解法中有关问题的研究

以地震反应谱的形式，阐述了复阻尼系统在频域求解过程中容易出现的问题。通过理论与计算分析得知，这些问题对反应谱计算有很大的影响。另外，还初步分析了时域精确法及频域分析方法的计算效率，认为时域精确法比频域分析方法的计算效率高。     

武汉砂土动剪切模量与阻尼比的试验研究

以武汉地铁4号线二期工程越江段饱和砂土为研究对象,通过室内GDS动力三轴试验,较为系统地研究了在单向循环荷载作用下砂土的动剪切模量和阻尼比规律特性及其影响因素。试验结果表明:动剪切模量、阻尼比与动剪应变的关系可以用Hardin-Drnevich双曲线模型进行描述;动剪切模量随动应变的增大而减小,随围压和固结比的增大而增大,而阻尼比的变化规律与动剪切模量相反。从而为工程建筑物的抗震设计提供了重要依据。     

黏性土的动剪切模量比和阻尼比与剪应变关系的统计分析

动剪切模量比和阻尼比是土体重要的动力特性参数,这两种参数取值的合理性对场地地震响应分析的结果有重要影响.为进一步完善黏性土的动剪切模量比和阻尼比随剪应变的变化关系的研究,给出了新的计算模型和推荐曲线.新曲线的计算模型基于Davidenkov模型和新的阻尼比计算模型,通过对搜集的大量黏性土数据进行非线性回归分析后得到.将分析结果与已有国内外学者的成果进行对比,验证了新计算模型具有较好的可靠性和工程实用性.     

利用ARX模型识别土-结构体系的低阶模态频率和阻尼

利用美国Alaska-14层的办公大楼及周围场地上记录到的地震动,对此结构进行了低阶模态频率和阻尼的识别。和考虑土-结构动力相互作用后的土-结体系的低阶模态的频率和阻尼的识别。提供了一种ARX参数模型辨识方法,并与非参数模型辨识比较分析,发现两种模型得到的低阶模态频率和阻尼基本一致,但在高阶模态上会出现明显的差异。通过分析还发现考虑土-结相互作用后,体系的传递函数幅值有所降低。并编制了相应的Matlab计算程序。     

Pre-shear effect on liquefaction resistance of a Fujian sand

Pre-shear history has been shown to be a critical factor in the liquefaction resistance of sand. By contrast to prior experimental studies in which triaxial shear tests were used to examine the effects of pre-shear on the liquefaction resistance of sand, hollow cylinder torsional shear tests were used in this study to avoid the influence of the inherent anisotropy that is inevitably produced during the sample preparation process because of gravitational deposition. A series of cyclic undrained shear tests were performed on sand samples that had experienced medium to large pre-shear loading. The test results showed that the liquefaction resistance of sand can be greatly reduced by its pre-shear history, and a pre-shear strain within the range from 0.1% to 5% can cause sand to be more prone to liquefaction. During the cyclic shear tests, the samples that had experienced pre-shear loading exhibited different behaviors when cyclic shear loading started in different directions, i.e., the clockwise direction and the counterclockwise direction. If the cyclic loading started in the identical direction as the pre-shear loading, then the mean effective stress of the sand was almost unchanged during the first half of the loading cycle; if the cyclic loading started in the direction opposite to that of the pre-shear loading, then the mean effective stress decreased significantly during the first half of the loading cycle. However, this anisotropic behavior was only remarkable during the first loading cycle. From the second cycle onward, the speeds of the decrease in the mean effective stresses in the two types of shear tests became similar.     

基于楼层剪力的等效阻尼比计算方法研究

针对现有附加有效阻尼比计算方法存在的问题,本文从能量的角度揭示了阻尼比对结构影响的机理。从结构设计的角度,提出一种在时程分析下基于楼层剪力的消能减震结构等效阻尼比计算方法。对布置黏滞阻尼器和软钢阻尼器的消能减震模型,采用本文提出的等效阻尼比计算方法,建立等效结构进行结构响应对比。结果表明,由该计算方法得到的等效阻尼比能够准确地评估阻尼器在结构中的耗能效果,建立的等效结构能够准确反映消能减震结构实际情况。基于楼层剪力的等效阻尼比计算方法通过等效结构楼层剪力大于或等于消能减震结构楼层剪力判断迭代完成,该方法计算过程不涉及阻尼器参数及结构形式,适用于所有阻尼器类型与结构类型。计算得到的等效结构进行设计能够确保结构设计的安全。     

Morison方程中动水阻力项对桥梁桩柱地震反应的影响

深水桥梁地震反应计算时,当采用Morison公式考虑水的作用时,增加了一个附加惯性项和一个附加阻尼项,其中附加阻尼项是非线性的。由于非线性附加阻尼项的存在,给采用反应谱方法求解桥梁的地震反应带来不便。讨论了非线性阻尼项对一般桥梁桩、墩结构地震反应的贡献,得到的结论是阻尼项的贡献很小,可以忽略。从而水中桥梁地震反应的计算就得到了很大的简化。     

抗震结构的阻尼减振效果分析

研究了抗震结构的阻尼减振效果。首先，考虑了单自由度体系在不同频率简谐干扰作用下阻尼比对结构反应的减小效果；然后，考虑了阻尼比对结构地震反应谱的影响，分析了我国现行建筑抗震设计规范反应谱，并讨论了不同阻尼比对水平地震影响系数的修正公式。     

土动剪切模量和阻尼比的推荐值和规范值的合理性比较

参照目前国内外试验测得的土的动剪切模量和阻尼比,以及多种土层工况和实际地震动输入下土层地震反应分析计算结果,对袁晓铭等给出的推荐值和《工程场地地震安全性评价工作规范》中给出的数值的合理性进行了对比研究。结果表明,与规范值相比,推荐值与国内外结果更相接近,特别是与国内结果相差不大,且避免了土层地震反应中地表反应谱“矮、粗、胖”现象,较符合客观实际情况,可供无试验资料情形和今后修订规范时参考。     

土的动模量和阻尼比研究述评

总结和评述了土的动模量和阻尼比的国内外研究现状,分析了现有工作不完善和存在缺陷的原因,提出了今后的研究设想。     

Using centrifuge tests data to identify the dynamic soil properties: Application to Fontainebleau sand

Knowledge of the dynamic properties of the soil is of great importance as the dynamic shear modulus and damping ratio are necessary input data in finite element modeling programs. This paper presents a post-processing strategy to identify the shear modulus and damping ratio vs. shear strain curves using the experimental results of a dynamic centrifuge program. Application is presented for the Fontainebleau sand. The proposed methodology is fast, robust and able to capture the nonlinear hysteretic behavior of the material. Based on the results, specific parameters for the Fontainebleau sand are identified for the empirical equation of shear modulus and damping ratio proposed by Ishibashi and Zhang [1]. It is found that confining pressure has an important influence on both shear modulus evolution and damping ratio.