The NOAA Goes-12 Solar X-Ray Imager (SXI) 1. Instrument, Operations, and Data

The Solar X-ray Imager (SXI) was launched 23 July 2001 on NOAAs GOES-12 satellite and completed post-launch testing 20 December 2001. Beginning 22 January 2003 it has provided nearly uninterrupted, full-disk, soft X-ray solar images, with a continuous frame rate significantly exceeding that for previous similar instruments. The SXI provides images with a 1 min cadence and a single-image (adjustable) dynamic range near 100. A set of metallic thin-film filters provides temperature discrimination in the 0.6 – 6.0 nm bandpass. The spatial resolution of approximately 10 arcsec FWHM is sampled with 5 arcsec pixels. Three instrument degradations have occurred since launch, two affecting entrance filters and one affecting the detector high-voltage system. This work presents the SXI instrument, its operations, and its data processing, including the impacts of the instrument degradations. A companion paper (Pizzo et al., this issue) presents SXI performance prior to an instrument degradation that occurred on 5 November 2003 and thus applies to more than 420000 soft X-ray images of the Sun.     

Formation of Transient Coronal Holes during the Eruption of a Quiescent Filament and its Overlying Sigmoid

By using Hα, He I 10830, EUV and soft X-ray (SXR) data, we examined a filament eruption that occurred on a quiet-sun region near the center of the solar disk on 2006 January 12, which disturbed a sigmoid overlying the filament channel observed by the GOES-12 SXR Imager (SXI), and led to the eruption of the sigmoid. The event was associated with a partial halo coronal mass ejection (CME) observed by the Large Angle and Spectrometric Coronagraphs (LASCO) on board the Solar and Heliospheric Observatory (SOHO), and resulted in the formation of two flare-like ribbons, post-eruption coronal loops, and two transient coronal holes (TCHs), but there were no significantly recorded GOES or Hα flares corresponding to the eruption. The two TCHs were dominated by opposite magnetic polarities and were located on the two ends of the eruptive sigmoid. They showed similar locations and shapes in He Ⅰ 10830, EUV and SXR observations. During the early eruption phase, brightenings first appeared on the locations of the two subsequent TCHs, which could be clearly identified on He Ⅰ 10830, EUV and SXR images. This eruption could be explained by the magnetic flux rope model, and the two TCHs were likely to be the feet of the flux rope.     

Early In-orbit Performance of Scanning Sky Monitor Onboard AstroSat

We report the in-orbit performance of Scanning Sky Monitor (SSM) onboard AstroSat. The SSM operates in the energy range 2.5 to 10 keV and scans the sky to detect and locate transient X-ray sources. This information of any interesting phenomenon in the X-ray sky as observed by SSM is provided to the astronomical community for follow-up observations. Following the launch of AstroSat on 28th September, 2015, SSM was commissioned on October 12th, 2015. The first power ON of the instrument was with the standard X-ray source, Crab in the field-of-view. The first orbit data revealed the basic expected performance of one of the detectors of SSM, SSM1. Following this in the subsequent orbits, the other detectors were also powered ON to find them perform in good health. Quick checks of the data from the first few orbits revealed that the instrument performed with the expected angular resolution of 12’ \(\times \) 2.5\(^\circ \) and effective area in the energy range of interest. This paper discusses the instrument aspects along with few on-board results immediately after power ON.     

The spatial distribution of 6 centimeter gyroresonance emission from a flaring X-ray loop

We compare simultaneous high resolution soft X-ray and 6 cm images of the decay phase of an M3 X-ray flare in Hale Region 16413. The photographic X-ray images were obtained on an AS & E sounding rocket flown 7 November, 1979, and the 6 cm observations were made with the VLA. The X-ray images were converted to arrays of line-of-sight emission integrals and average temperature throughout the region. The X-ray flare structure consisted of a large loop system of length 1.3 arc min and average temperature 8 × 10⁶ K. The peak 6 cm emission appeared to come from a region below the X-ray loop. The predicted 6 cm flux due to thermal bremsstrahlung calculated on the basis of the X-ray parameters along the loop was about an order of magnitude less than observed. We model the loop geometry to examine the expected gyroresonance absorption along the loop. We find that thermal gyroresonance emission requiring rather large azimuthal or radial field components, or nonthermal gyrosynchrotron emission involving continual acceleration of electrons can explain the observations. However, we cannot choose between these possibilities because of our poor knowledge of the loop magnetic field.     

The microscope for Beagle 2

The microscope for the Beagle 2 lander, which was launched as part of the European Space Agency's Mars Express mission on 2 June 2003, will provide images of the Martian surface at around resolution. It will provide optical images of the surface of Mars at a resolution 5 times higher than any other experiment currently planned. The device has a working distance of and uses a set of 12 light-emitting diodes which surround the aperture to illuminate the sample in four colours. The target is brought into focus using a stepper motor. This article describes the scientific objectives and the design of the microscope. It also discusses initial results from ground calibration exercises which were designed to validate the system and describes aspects of its operation.     

A simple method for correcting spatially resolved solar intensity oscillation observations for variations in scattered light

A measurement of the intensity distribution in an image of the solar disk will be corrupted by a spatial redistribution of the light that is caused by the Earth's atmosphere and the observing instrument. If the precise form of the spatial point spread function is known and can be modeled, then the observed image can be corrected for its effects. However, accurate modeling of the spatial point spread function, which can be considered as composed of a blurring component and a scattering component (Zwaan, 1965), is difficult and the correction for its effects is computationally expensive.We introduce a simple correction method that is applicable for solar p-mode intensity observations obtained over a period of time in which there is a significant change in the scattering component of the point spread function. The method circumvents the problems incurred with an accurate determination of the spatial point spread function and its subsequent deconvolution from the observations. The method only corrects the spherical harmonic coefficients that represent the spatial frequencies present in the image and does not correct the image itself. The method is computationally inexpensive and has the potential of being useful in correcting for changes in the blurring component of the point spread function and also for correcting velocity images.     

The development of X-ray flare onsets near active region filaments

Skylab X-ray images of the early phases of six active region transient brightenings were compared with simultaneous H images to study the spatial relationships between filaments and the X-ray brightenings. When the X-ray loops were roughly perpendicular to the axes of the H filaments, the filaments did not disappear. X-ray loops which appeared nearly parallel to the filaments were generally associated with the disappearances of those filaments. It is suggested that the perpendicular loops correspond to the class I X-ray flares of Pallavicini et al. (1977) while the parallel loops are the early phases of their class II flares characterized in the decay phases by arcades of large loops with low energy densities. Both kinds of X-ray flares can be associated with impulsive phases.     

X-ray and optical observations of the AM Her star H0139-68

We summarize results of our ongoing analysis of optical and X-ray data on the AM Herculis type binary H0139-68 (see also Beuermann et al., 1984; Schwope and Beuermann, 1985).Paper presented at the IAU Colloquium No. 93 on Cataclysmic Variables. Recent Multi-Frequency Observations and Theoretical Developments, held at Dr. Remeis-Sternwarte Bamberg, F.R.G., 16–19 June, 1986.     

Huygens/HASI 2002 balloon test campaign: Probe trajectory and atmospheric vertical profiles reconstruction

In the framework of the activities going on in preparation for the mission of the Huygens probe in Titan's atmosphere (January 2005), the Huygens Atmospheric Structure Instrument (HASI) team scheduled and performed several balloon campaigns to test the HASI sensors’ performance in flight conditions in the Earth's atmosphere. In particular, pressure conditions reached during each test are similar to those expected in Titan's lower atmosphere. A 1:1 scaled mock-up of the Huygens probe was launched with a stratospheric balloon in 2001 (Br. Assoc. Adv. Sci. 33 (2001) 1109) and in 2002 (Br. Assoc. Adv. Sci. 34 (2002) 911; Adv. Space. Sci. (2003)) from the G. Broglio base of the Italian Space Agency, located in Trapani Milo (Sicily). In both cases the mock-up was dropped from an altitude higher than 27 and , respectively, and recovered on the ground after a parachuted descent. In this paper, we describe the results obtained in reconstructing (i) the probe descent trajectory and (ii) the profiles of the physical quantities characterizing the Earth's atmosphere, on the basis of a complete analysis of the data obtained during the HASI 2002 balloon flight experiment. Using temperature and pressure measurements, we are able to reach an accuracy of the order of 0.5% on the altitude reconstruction during the descent. We validate both the models used for trajectory reconstruction and to check the sensors’ performance. We describe the problems faced in determining the Huygens probe descent trajectory in Titan's atmosphere focusing our discussion on the critical aspects of the descent reconstruction (such as the uncertainties due to measurement errors, limited knowledge of the atmospheric composition, etc.) and the validity of the adopted assumptions.     

Sounding Rocket Observations of Active Region Soft X-Ray Spectra Between 0.5 and 2.5 nm Using a Modified SDO/EVE Instrument

Spectrally resolved measurements of individual solar active regions (ARs) in the soft X-ray (SXR) range are important for studying dynamic processes in the solar corona and their associated effects on the Earth’s upper atmosphere. They are also a means of evaluating atomic data and elemental abundances used in physics-based solar spectral models. However, very few such measurements are available. We present spectral measurements of two individual ARs in the 0.5 to 2.5 nm range obtained on the NASA 36.290 sounding rocket flight of 21 October 2013 (at about 18:30 UT) using the Solar Aspect Monitor (SAM), a channel of the Extreme Ultaviolet Variability Experiment (EVE) payload designed for underflight calibrations of the orbital EVE on the Solar Dynamics Observatory (SDO). The EVE rocket instrument is a duplicate of the EVE on SDO, except the SAM channel on the rocket version was modified in 2012 to include a freestanding transmission grating to provide spectrally resolved images of the solar disk with the best signal to noise ratio for the brightest features, such as ARs. Calibrations of the EVE sounding rocket instrument at the National Institute of Standards and Technology Synchrotron Ultraviolet Radiation Facility (NIST/SURF) have provided a measurement of the SAM absolute spectral response function and a mapping of wavelength separation in the grating diffraction pattern. We discuss techniques (incorporating the NIST/SURF data) for determining SXR spectra from the dispersed AR images as well as the resulting spectra for NOAA ARs 11877 and 11875 observed on the 2013 rocket flight. In comparisons with physics-based spectral models using the CHIANTI v8 atomic database we find that both AR spectra are in good agreement with isothermal spectra (4 MK), as well as spectra based on an AR differential emission measure (DEM) included with the CHIANTI distribution, with the exception of the relative intensities of strong Fe?xvii lines associated with \(2p^{6}\)–\(2p^{5}3{s}\) and \(2p^{6}\)–\(2p^{5}3{d}\) transitions at about 1.7 nm and 1.5 nm, respectively. The ratio of the Fe?xvii lines suggests that the AR 11877 is hotter than the AR 11875. This result is confirmed with analysis of the active regions imaged by X-ray Telescope (XRT) onboard Hinode.     

Chromospheric variability in late-type dwarfs from high-resolution spectra of Caii H

Precise photometric observations of stars in the double cluster h and Persei reveal a large spread in the colours and magnitudes of the upper Main-Sequence; half of the stars are variables that are Be stars or related stars. The reported age difference between both clusters is found to be spurious. Rotation apparently affects both the intrinsic and the observed colours of the early-type stars in h and Persei. This result questions the validity of photometric calibrations that heavily rely on h and Persei or similar clusters.Paper presented at the 11th European Regional Astronomical Meeting of the IAU on New Windows to the Universe, held 3–8 July, 1989, Tenerife, Canary Islands, Spain.     

Impulsive phase heating and a coronal explosion in a solar flare

The flare of 12 November 1980, 0250 UT, in Active Region 2779 (NOAA classification) was studied by using X-ray images obtained with the Hard X-Ray Imaging Spectrometer aboard NASA's Solar Maximum Mission. In a ten-minute period, between about 0244 and 0254 UT, some five short-lived impulsive bursts occurred. We found that the so-called hard bursts ( 15 keV) are also detectable in low energy images. During that 10 min period - the impulsive phase - the heat input into the flare and the total number of energetic electrons increased practically exponentially, to reach their maximum values at 0254 UT. At the end of that period, when the thermal energy content of the flare was largest, a burst was observed, for the first time, to spread in a broad southern direction from an initially small area with a speed of about 50 km s^–1. We have called this phenomenon a coronal explosion.Fokker Aircraft Industries, Schiphol, The Netherlands.     

A quantitative treatment of solar ‘seeing’, I

Measurements of temperature-fluctuation statistics in a locally homogeneous, isotropic turbulent atmosphere above level land are shown to enable the quality of telescopic images of celestial objects to be calculated. Data obtained with captive-balloon-borne apparatus are used, together with other existing data, to calculate the modulation transfer function and Strehl Definition for both long- and short-exposure images formed by typical solar telescopes operating under a variety of meteorological conditions. The size of telescope may thus be matched to the expected atmospheric conditions; the improvement in performance and utilization of the instrument, obtainable by raising it on a tower, may be calculated. An 11-cm aperture telescope, for example, is shown to be atmosphere-limited for long exposures in average daytime conditions; raising it from 2 to 30 m above the ground makes an almost threefold improvement in definition. If observations are confined to intervals of good seeing the full resolution of such a telescope may be realized. The existence of such intervals is attributed to convective thermal structure in the atmosphere and observational statistics of periods of below-average temperature fluctuation are given for a range of general meteorological conditions.     

New Digital Magnetograph At Big Bear Solar Observatory

A new digital magnetograph system has been installed and tested at Big Bear Solar Observatory. The system uses part of BBSO's existing videomagnetograph (VMG) system: a quarter wave plate, a ferro-electric liquid crystal to switch polarizations, and a 0.25 Å bandpass Zeiss filter tuned at Cai 6103 Å. A new 256×256 pixels, 12-bit Dalsa camera is used as the detector and as the driver to switch the liquid crystal. The data rate of the camera is 90 frames s–1. The camera is interfaced to a Pentium-166 PC with a Tech imaging board for data acquisition and analysis. The computer has 128 MByte of RAM, and up to 700 live images can be stored in memory for quick post-exposure image processing (image selection and alignment). We have significantly improved the sensitivity and spatial resolution over the old BBSO VMG system. In particular: (1) New digital image data are in 12 bits while the video signal is digitized as 8 bits. Polarizations weaker than 1% can not be detected by a single pair subtraction in the video system. The digital system can detect a polarization signal of about 0.3% by a single pair subtraction. (2) Data rate of the digital system is 90 frames s–1, that of the video system is 30 frames s–1. So the time difference between two polarizations is reduced in the new system. Under good seeing conditions, the data rate of 90 frames s–1 ensures that most of the wavefront distortions are frozen and fairly closely the same for the left and right circular polarized image pairs. (3) Magnetograms are constructed after image selection and alignment. We discuss the characteristics of this new system. We present the results of our first tests to reconstruct magnetograms with speckle interferometric techniques. We also present some preliminary results on the comparison of facular/micropore contrasts and magnetic field structure. The experiment with this small detector lays ground for a larger format digital magnetograph system at BBSO, as well as a future Fabry-Pérot system, which will be able to scan across the spectral line.     

Solar soft X-rays and solar activity

Flare-associated soft X-ray bursts (8–12 Å) are examined for 283 events observed by OSO-III. These bursts are shown to be predominantly thermal in nature. Their time-profiles are roughly similar to those of the associated H flares, although the X-ray burst begins about two minutes earlier, on the average. The strength of the soft X-ray burst is directly related to the area and brilliance of the flare, the age and flare-richness of the associated plage, and the general level of solar activity at the time of the burst. The peak enhancements in the soft X-ray and H emission rates during flares are of the same order of magnitude, as are the total flare energies radiated at these wavelengths. We estimate that soft X-radiation accounts for up to 10% of a flare's total electromagnetic emission.NRC/NAS Resident Research Associate.     

Coronal Shocks of November 1997 Revisited: The Cme–Type II Timing Problem

We re-examine observations bearing on the origin of metric type II bursts for six impulsive solar events in November 1997. Previous analyses of these events indicated that the metric type IIs were due to flares (either blast waves or ejecta). Our point of departure was the study of Zhang et al. (2001) based on the Large Angle and Spectrometric Coronagraphs C1 instrument (occulting disk at 1.1 R₀) that identified the rapid acceleration phase of coronal mass ejections (CMEs) with the rise phase of soft X-ray light curves of associated flares. We find that the inferred onset of rapid CME acceleration in each of the six cases occurred 1–3 min before the onset of metric type II emission, in contrast to the results of previous studies for certain of these events that obtained CME launch times 25–45 min earlier than type II onset. The removal of the CME-metric type II timing discrepancy in these events and, more generally, the identification of the onset of the rapid acceleration phase of CMEs with the flare impulsive phase undercuts a significant argument against CMEs as metric type II shock drivers. In general, the six events exhibited: (1) ample evidence of dynamic behavior [soft X-ray ejecta, extreme ultra-violet imaging telescope (EIT) dimming onsets, and wave initiation (observed variously in H, EUV, and soft X-rays)] during the inferred fast acceleration phases of the CMEs, consistent with the cataclysmic disruption of the low solar atmosphere one would expect to be associated with a CME; and (2) an organic relationship between EIT dimmings (generally taken to be source regions of CMEs) and EIT waves (which are highly associated with metric type II bursts) indicative of a CME-driver scenario. Our analysis indicates that the broad (90 to halo) CMEs observed in the outer LASCO coronagraphs for these impulsive events began life as relatively small-scale structures, with angular spans of 15 in the low corona. A review of on-going work bearing on other aspects (than timing) of the question of the origin of metric type II bursts (CME association; connectivity of metric and decametric-hectometric type II shocks; spatial relationship between CMEs and metric shocks) leads to the conclusion that CMEs remain a strong candidate to be the principal/sole driver of metric type II shocks vis-à-vis flare blast waves/ejecta.     

High-Resolution Hα Observations of Proper Motion in NOAA 8668: Evidence for Filament Mass Injection by Chromospheric Reconnection

There have been two different kinds of explanations for the source of cool material in prominences or filaments: coronal condensations from above and cool plasma injections from below. In this paper, we present observational results which support filament mass injection by chromospheric reconnection. The observations of an active filament in the active region NOAA 8668 were performed on 17 August 1999 at a wavelength of H–0.6 Å using the 65 cm vacuum reflector, a Zeiss H birefringent filter, and a 12-bit SMD digital camera of Big Bear Solar Observatory. The best image was selected every 12 s for an hour based on a frame selection algorithm. All the images were then co-aligned and corrected for local distortion due to the seeing. The time-lapse movie of the data shows that the filament was undergoing ceaseless motion. The H flow field has been determined as a function of time using local correlation tracking. Time-averaged flow patterns usually trace local magnetic field lines, as inferred from H fibrils and line-of-sight magnetograms. An interesting finding is a transient flow field in a system of small H loops, some of which merge into the filament. The flow is associated with a cancelling magnetic feature which is located at one end of the loop system. Initially a diverging flow with speeds below 10 km s^–1 is visible at the flux cancellation site. The flow is soon directed along the loops and accelerated up to 40 km s^–1 in a few minutes. Some part of the plasma flow then merges into and moves along the filament. This kind of transient flow takes place several times during the observations. Our results clearly demonstrate that reconnection in the photosphere and chromosphere is a likely way to supply cool material to a filament, as well as re-organizing the magnetic field configuration, and, hence, is important in the formation of filaments.     

The mark II Nançay radioheliograph

We describe the new Nançay Radioheliograph (version II) which is a multicorrelator system. The main characteristics of this instrument are high space and time resolutions and flexible on-line data processing. At present it produces one-dimensional images at 169 MHz. This instrument is mainly intended for solar observations.An accurate calibration of the instrument has been carried out leading to a precise fringe stopping and to a proper knowledge of the grating response. Preliminary solar results are presented: existence of apparent motions in noise storms with a velocity of the order of 5000 km s^–1; observations of radiobursts as narrow as 0.7 (Kerdraon, 1977); observations of spikeburst activity.Presently in Sydney, Australia.