共查询到20条相似文献,搜索用时 93 毫秒
1.
江西省德兴铜矿矿区重金属元素的环境效应 总被引:6,自引:0,他引:6
本文系统研究了德兴铜矿排石场和尾砂库的环境问题,以环境介质(水土植物)中重金属元素含量为研究对象,论述矿区重金属的环境效应。研究结果表明祝家村低品位矿石堆浸场淋滤产生的酸性废水是造成大坞河流域重金属污染的主要来源。大坞河上游水体中Cu元素含量高达14506μg/L,是国家Ⅲ级水标准的14倍之多,Zn元素含量高达2938μg/L,是国家Ⅲ级水标准的2.9倍,同时pH值在3~4范围内;到中下游水体中Cu元素含量减小到几千到几百μg/L,水质有所改善。大坞河沿岸上游和中游土壤重金属含量受河水影响,随着与河岸距离的增加而减小。同时水稻中Pb元素含量是国家粮食标准的2倍。推测4#尾砂库尾砂表层氧化带深度大于80cm;而1#尾砂库库内尾砂中氧化带估计在0~25cm处。推测两个尾砂库产酸能力小于酸中和能力,故坝底水中pH值在7左右,对周围水体影响较小。与4#尾砂库距离近的石墩头村稻田表层土壤中Cu、Mo元素含量较高,远离尾砂库土壤中重金属含量降低。同时4#尾砂库周围土壤中Cd、Pb、Cu元素的吸附态、碳酸盐态比例在20%左右,因而在酸性环境下较容易被植物吸收。1#尾砂库矿建村种植的小白菜中Pb元素含量超过国家蔬菜标准的4倍,Cu、Pb、Zn元素含量严重超过背景值。 相似文献
2.
3.
4.
德兴铜矿床地质环境模型初探 总被引:1,自引:0,他引:1
德兴铜矿位于赣东北地区,该矿床自开发以来,为国家和地方作出了巨大贡献。在矿山环境方面,总体上是矿山环境较好的矿区,但局部仍存在一定的问题。本文建立了包含影响潜在环境效应的地质因素、开采前的环境特征和开采过程中的环境特征三方面内容的矿床地质环境模型。据原生铜矿石、氧化矿石、淋滤矿石和次生硫化物矿石的有关元素含量,计算出开采前由矿床向环境输出了2.1万吨Cu、7.6万吨S和941吨Mo。主要金属硫化物黄铁矿由地下被带至地表经氧化和水解反应后产生酸、Fe^3 及释放出的As、Cd、Cu等重金属元素污染了环境。黄铜矿在人工堆浸后,排放水中的Cu^2 及其它重金属元素也对环境造成了污染。矿山开采低品位矿石堆浸产生的集液池之外排水为大坞河之污染源,该源头每年至少输出Cu 202吨、Zn 22.04吨、Cd 307kg。30年间铜矿开采过程中大坞河流域河床沉积物中有2.58吨Pb、3.1吨Zn、351.2吨Cu和11.5吨Mo,均为河水污染所致。 相似文献
5.
大冶铜绿山铜铁矿床尾矿砂中重金属与微量元素环境地球化学特征研究 总被引:5,自引:1,他引:5
为了解铜绿山铜铁矿床尾矿砂中重金属元素的释放迁移地球化学过程及其扩散范围,运用ICP.MS对大冶铜绿山铜铁矿床尾砂库的尾矿砂及其相关的水系沉积物和土壤中重金属元素、稀土元素进行了测试分析.环境地球化学研究发现,研究区重金属元素在尾矿砂垂向剖面和水系沉积物中具有较明显的垂向和横向空间分布规律;尾砂库西北边水稻田土壤明显受到Cu、Zn、Cd等重金属元素的污染,稀土元素分布模式及微量元素比值研究揭示了污染原因可能是水稻田土壤继承了附近废弃的选矿厂和矿体的特征;尾矿砂和水系沉积物稀土元素分布模式及微量元素比值的变化规律,在一定程度上可以解释重金属元素在垂向和横向空间上的分布特征. 相似文献
6.
7.
以广西大厂镇鲁塘铅锌矿尾砂为研究对象,通过淋滤实验研究了不同氧化还原条件下尾砂中Cu、Cd、Zn、Pb和As等元素的活化和迁移规律。结果表明:经高浓度氧化、高浓度还原条件处理的尾矿表现为pH<7的酸性环境,经低浓度氧化环境条件处理的尾砂呈现pH>7的弱酸性至弱碱性环境;尾砂中Cu、Cd元素活化迁移受pH值的影响明显,即高浓度还原和高浓度氧化条件可以促进Cu和Cd元素的迁移,酸性条件对Cu和Cd元素的迁移起到促进作用;Zn与Cd元素存在竞争吸附关系,但二者仍有明显差别;Pb和As元素受到还原条件的影响,能有效促进Pb和As元素的释放迁移。在淋滤实验前期,铅锌矿的表面阻力较小,由于环境酸碱性的改变,初始尾砂对重金属元素的吸附位能发生变化,重金属元素初期迁移能力得到加强;淋滤后期,矿物颗粒表面由于发生氧化还原反应,促使颗粒表面的阻力增加,重金属元素的溶出量减少,迁移能力受到抑制。 相似文献
8.
9.
10.
富镉铅锌矿山的环境影响——以贵州都匀牛角塘矿床为例 总被引:4,自引:0,他引:4
矿床的开采和选冶,常常将其中重金属有毒元素释放到环境中,铅锌矿造成的环境污染尤为严重。贵州都匀牛角塘矿床是国内外少见的富镉锌矿床,其中镉高度富集。本文通过对通过对矿区水、土壤及植物的分析和调查,发现其中镉和锌均已远远超过国家标准,矿区周围环境已受到严重污染。研究表明矿床的表生风化作用是镉等重金属释放的主要途径之一,更重要的是矿山的采矿和选矿更加剧了其释放量,虽在目前人群中没有明显中毒现象,可能是由于矿床开采时间较短,Cd等重金属元素在人体中积累不多所致。但矿山环境污染是污染元素长期积累造成的结果,即使在矿山关闭十年、上百年甚至上千年时间内,矿山尾矿淋滤液对环境生态的影响依然存在。因此,在矿山开发过程中必须注意矿床中有用元素的综合利用和重视环境保护,防患于未然。特别是对这类富含有毒污染元素的金属矿山的开采更应如此。 相似文献
11.
S. Viswanathan K. Surya Prakash Rao B. Mahabaleswar 《Journal of the Geological Society of India》2013,82(6):621-627
Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours. 相似文献
12.
13.
奥地利安东帕有限公司 《岩矿测试》2009,28(3):306-306
最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提 相似文献
14.
E. M. Prasolov S. A. Sergeev B. V. Belyatsky E. S. Bogomolov K. A. Gruzdov I. N. Kapitonov R. Sh. Krymsky V. O. Khalenev 《Geochemistry International》2018,56(1):46-64
This paper reports the first results of a study of 11 isotope systems (3He/4He, 40Ar/36Ar, 34S/32S, 65Cu/63Cu, 62Ni/60Ni, 87Sr/86Sr, 143Nd/144Nd, 206–208Pb/204Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others. 相似文献
15.
Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance. 相似文献
16.
17.
岩石密度和超高压岩石折返速率 总被引:1,自引:3,他引:1
在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。 相似文献
18.
Mercury,arsenic, antimony,and selenium contents of sediment from the Kuskokwim River,Bethel, Alaska,USA 总被引:1,自引:0,他引:1
The Kuskokwim River at Bethel, Alaska, drains a major mercury-antimony metallogenic province in its upper reaches and tributaries. Bethel (population 4000) is situated on the Kuskokwim floodplain and also draws its water supply from wells located in river-deposited sediment. A boring through overbank and floodplain sediment has provided material to establish a baseline datum for sediment-hosted heavy metals. Mercury (total), arsenic, antimony, and selenium contents were determined; aluminum was also determined and used as normalizing factor. The contents of the heavy metals were relatively constant with depth and do not reflect any potential enrichment from upstream contaminant sources. 相似文献
19.
滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床. 相似文献
20.
Alexander E. C. Broberg J. S. Kehren A. R. Graziani M. M. Turri W. L. 《Environmental Geology》1993,22(4):353-361
Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×106 1 of partially treated effluent and about 600 m3 of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes. 相似文献