V-M荷载作用下双层黏土地基破坏包络线研究

地基破坏包络线的研究是复合加载模式下地基承载力设计的关键。根据建立的数值计算模型,用Abaqus商业软件分析了V-M荷载作用下,位于双层黏土地基上条形基础的破坏包络线随上层土厚度比、土层强度比的变化规律,以及地基破坏模式随荷载偏心率的变化趋势。用有效面积概念将传统竖向极限承载力换算为V-M荷载平面的破坏包络线,与数值计算结果进行对比。结果表明,公式换算方法适用于均质黏土地基,而对双层黏土地基偏于保守。     

复合加载模式作用下地基承载性能数值分析

确定竖向荷载(V)、水平荷载(H)和力矩(M)共同作用下建筑物地基的破坏模式及在荷载空间(H,V,M)中的破坏包络面是地基设计中的关键问题。为提高Swipe试验方法计算精度,提出了改进方案,进而利用有限元方法分析了复合加载模式作用下均质粘性土地基上条形基础的破坏包络面。计算表明,基于改进Swipe试验方法的数值模拟结果明显好于常规Swipe试验方法。针对海洋工程中实际复合加载模式的特点,探讨了竖向荷载分量V对地基破坏模式和H-M荷载平面上的破坏包络线的影响,结果表明竖向荷载分量显著地改变了地基的破坏模式及包络线的形状。     

复合加载下考虑接触作用的地基承载特性数值分析

港口、海洋工程结构物基础一般处于复合加载状态,其极限承载力通常采用近来引入的极限荷载图进行评价.对位于地基表面的重力式海洋基础,需要考虑基础与地基间的接触特性对极限承载力的影响.以大型通用有限元软件ABAQUS为计算平台,建立了复合加载模式的地基极限承载力数值分析方法;针对饱和黏土地基上的表面基础,利用在ABAQUS平台上开发的接触计算模块,模拟基础与地基间竖向可分离、切向完全粘结的接触作用;进而基于建立的分析方法,进行系统的有限元计算,分析地基的破坏模式随荷载条件的变化,给出地基的极限荷载包络图,并与经典承载力计算公式结果进行对比.研究结果表明,经典承载力计算公式低估了三维荷载条件下的地基极限承载力,有限元计算模型及数值分析方法,可以较好地分析研究地基的失稳机理及承载力特性,并可考虑基础与地基不同的接触条件对破坏模式及组合极限承载力的影响.     

近海重力式建筑物地基设计与计算的若干问题

鉴于波浪激起重力式建筑物的振动为海底地基上的主要荷载之一,同时为能合理地设计,文中介绍了笔者研究过的统一等效谐振荷载以及海底地基的变形、稳定性与液化势等特性.基于这些研究,提出了近海重力式建筑物地基设计与计算的若干考虑.     

重载码头堆场CFG桩网复合地基离心模型试验研究

CFG桩网复合地基广泛应用于处理软土地基。采用土工离心模型试验研究某码头堆场超大荷载下CFG桩网复合地基的变形和桩土应力特性,试验模拟了地基、CFG桩、树根桩、加筋垫层、防尘网和轨道梁基础、矿石堆载等,分析了超大荷载作用下复合地基表面变形、桩顶轴力、桩间土压力、桩土应力比的变化规律。试验结果表明,复合地基的沉降速率在稳定控制标准之内,沉降量满足堆场使用要求,防尘网基础和轨道梁基础水平位移和沉降均很小,桩土应力比为25.2~43.8,CFG桩网复合地基在350 kPa荷载作用下是稳定安全的,达到了预期加固效果。     

软土地基沉箱防波堤失稳模式及稳定性分析方法

针对现阶段深水软黏土地基防波堤建设的设计理论和稳定性分析方法尚不成熟,结合实际工程,采用三维弹塑性有限元数值分析方法,研究在水平或竖直单一方向荷载以及复合加载条件下软黏土地基上沉箱防波堤的失稳模式,提出破坏包络线的稳定性判别方法。在波浪水平荷载作用下,深水软基上沉箱防波堤发生倾覆失稳破坏,失稳转动点为沉箱底面以下中轴线偏右的某点,不同于规范中规定的岩石或砂质地基沉箱倾覆转动点为其后踵点;在重力等竖向荷载作用下,沉箱的失稳模式为结构整体下陷,抛石基床及地基形成连贯的塑性区域,呈现较明显地冲剪破坏形式;在水平、竖向复合荷载作用下,软基上沉箱防波堤的破坏包络线由结构倾覆破坏线和地基承载力破坏线组成,包络线将荷载组合区分成稳定区、仅发生水平承载力不足倾覆破坏区、仅发生地基竖向承载力不足破坏区、同时发生水平承载力和地基竖向承载力不足破坏区4个区域。研究成果为深水软基沉箱防波堤建设提供参考和借鉴。     

有限元法在桩靴承载力计算中的应用

自升式钻井平台插桩是地基土在桩靴荷载作用下发生连续的塑性破坏的动态过程,当地基极限承载力等于桩靴荷载时插桩完成。经典土力学极限承载力理论对土体潜在滑动面做了假设,无法有效分析土体内部的破坏过程。本研究应用有限元法（FEM ）对插桩过程进行了模拟,得到地基土的破坏机制以及中间荷载下土体的应力、应变情况,通过和各理论公式计算的极限承载力进行对比分析,分析影响地基极限承载力的因素。研究表明,基础宽度与硬土层厚度的比值 B/H越大,下卧软土层越容易发生塑性破坏,极限承载力明显下降,当B/H＜0．286时,可以忽略下卧软土层对地基承载力的影响。     

嵌入式筒型结构抗倾稳定性简化计算方法

针对嵌入式筒型结构在淤泥质海床上的工作机理,建立其在软土地基上的理论计算模型,提出适用于该模型的土压力、摩阻力、地基反力的计算方法,由静力平衡方程,求解得到维持结构稳定的水平极限荷载。通过ANSYS数值模拟软件进行分析,并通过荷载位移曲线找到结构发生倾覆破坏时的极限荷载,对理论计算进行验证。     

东营地区地基土工程特性分析

东营地区地处黄河三角洲,其地层主要由第四纪新近沉积土和一般沉积土构成。其特点是地层较软弱,天然地基承载力低,承受荷载后地基变形较大。为了适应东营地区天然地基承载力低的特殊地质情况,目前常用的地基处理方法是水泥粉体喷射搅拌桩复合地基。采用水泥粉喷搅拌桩复合地基处理技术以后,复合地基承载力可提高到天然地基承载力的1.22.3倍。     

扩底抗拔桩动态变形全过程承载特性模型试验研究

利用砂土中扩底抗拔桩的模型试验,研究从开始加载到破坏时扩底抗拔桩地基动态变形全过程的承载特性。试验结果表明:半模试验得到的极限荷载和破坏面均略小于全模试验结果,采用半模试验测量地基变形过程与破坏模式有明显优势,用半模试验代替全模试验是可行的;随着桩顶荷载的增加,扩大头上方的土体由压缩变形逐渐发展为局部的压缩—剪切破坏;扩大头对其上部的桩侧摩阻力有增强作用,对其下部的桩侧摩阻力有削弱作用;扩大头在工作荷载、极限荷载和破坏荷载作用时分担的荷载比例为15%~20%。     

Numerical study on long-term monopile foundation response

This paper analyzes the long-term monopile foundation that undergoes numerous mechanical cycles. The semiempirical scheme is adopted to involve a mechanical constitutive model to extract stress and strains at the first cycle and polynomial-type strain accumulation functions to track the progressive plastic deformation. In particular, the strain function contains the fundamental features that require simulating the long-term response of geomaterials: volumetric strain (terminal void ratio) and shear strain (shakedown or ratcheting), the strain accumulation rate, and stress obliquity. The numerical simulation shows evolution of displacements, pile rotation, and stress redistribution along the embedded pile as the number of load cycles increases. The analysis highlights that the pile rigidity affects the pattern of horizontal stress and displacement. The repetitive lateral load enhances the lateral load resistance due to soil densification along the pile.     

Microbial Biomass and Organic Nutrients in the Deep-Sea Sediments of the Central Indian Ocean Basin

In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification

An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

Phylogenetic diversity and phenotypic characterization of cultivable bacterioplankton isolated from polar oceans

A set of 27 marine planktonic bacteria isolated from the polar regions was characterized by 16S rDNA sequencing and physiological and biochemical testing. More than half of these bacteria were positive for caseinase, gelatinase and 13-glucosidase, and could utilize glucose, maltose or malic acid as carbon source for cell growth. Twelve isolates expressed nitrate reduction activities. Except for one antarctic isolate BSwlO175 belonging to Actinobacteria phylum, these isolates were classified as γ-Proteobacteria, suggesting that γ-Proteobacteria dominated in cultivable marine bacterioplankton at both poles. Genus Pseudoalteromonas was the predominant group in the Chukchi Sea and the Bering Sea, and genus ShewaneUa dominated in cultivable bacterioplankton in the Prydz Bay. With sequence similarities above 97%, genus Psychrobacter was found at both poles. These 27 isolates were psychrotolerant, and significant 16S rDNA sequence similarities were found not only between arctic and antarctic marine bacteria （ 〉 99% ）, but also between polar marine bacteria and bacteria from other aquatic environments （ ≥ 98.8% ）, including temperate ocean, deep sea, pond and lake, suggesting that in the polar oceans less temperature-sensitive bacteria may be cosmopolitan and have a bipolar, even global, distribution at the species level.     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.