Mixing-height estimation in the convective boundary layer using sodar data

Sodar has been used for about 20 years to determine mixing height. However, estimation of the height of a convective boundary layer (CBL) that exceeds the sodar-probing range is still an unsolved question. As one possible way, it is suggested that one adapt a simple mixed-layer model to sodar observations during the morning growth period of the CBL, when its top can be clearly detected. Results are compared with other methods for CBL-height estimation from sodar data that have been proposed in the literature. Finally, some prognostic aspects are discussed.     

Composing the diurnal cycle of mixing height from simultaneous sodar and wind profiler measurements

Mixing heights have been determined independently from sodar and boundary-layer wind profiler measurements carried out at the Meteorological Observatory Lindenberg of the German Weather Service between 1 June 1994 and 6 July 1994. Good agreement between both systems was found for mixing height values between about 250 m and 700 m, i.e., in an evolving convective boundary layer. Considering the typical sounding ranges of the sodar (50 m up to 800 m) and of the wind profiler (200 m up to higher than 3000 m), simultaneous operation of the two systems is demonstrated to be a promising tool for continously monitoring the mixing height throughout its complete diurnal cycle.     

大气边界层高度确定及应用研究进展

大气边界层高度是表征边界层特征的重要参量,影响边界层内水热、物质、能量的垂直分布,也是数值模拟、环境评估中的重要参数。从湍流运动、热力作用、动力作用以及物质分布等多视角总结了大气边界层高度的定义及确定方法,回顾了采用直接观测手段和遥感手段确定大气边界层高度的不同方法,对比了大气边界层高度不同获取手段的优缺点,梳理了大气边界层高度参数化方案,探讨了大气边界层高度确定中存在的问题,并提出未来相关研究和应用可能突破方向。     

Evaluation of Sodar methods for the determination of the atmospheric boundary layer mixing height

Summary It is the purpose of this paper to evaluate the different Sodar approaches and methods for the determination of the atmospheric mixing height against direct measurements. To achieve this objective a specific experiment was designed and performed incorporating, a research home made Sodar, a tethered balloon and a radiosonde facility as well as a conventional ground based meteorological station. The obtained data were statistically treated and analyzed to high-light the advantages and disadvantages of the various methods during different meteorological conditions. The results indicate that all three manual methods produce reasonable estimates during convective conditions, while for the stable cases the acceptable techniques are reduced to two. For the automated approach however, the two methods produced quite acceptable estimates during convective conditions, while for the stable cases none was found suitable for use.     

Estimating surface sensible heat flux using sodar and surface temperature measurements in the evolving convective boundary layer

A simple method is described for estimating the sensible heat flux by using a Doppler sodar system and a thermal probe. This method, which can be applied to a convective boundary layer in morning hours, is based on knowing the zero heat flux level from the reflectivity and the vertical wind speed.     

Airborne measurements of the vertical flux of ozone in the boundary layer

A fast-response chemiluminescent ozone sensor was mounted in an aircraft instrumented for air motion and temperature measurements. Measurements of the vertical flux of ozone by the eddy correlation technique were obtained after correcting for time delay and pressure sensitivity in the ozone sensor output. The observations were taken over eastern Colorado for two days in April, one a morning and the other an afternoon flight. Since the correlation coefficient of ozone and vertical velocity is small compared to, for example, temperature and vertical velocity in the lower part of the convective boundary layer, an averaging length of the order of 100 km was required to obtain a reasonably accurate estimate of the ozone flux. The measured variance of ozone appeared to be too large, probably mainly due to random noise in the sensor output, although the possibility of the production of ozone fluctuations by chemical reactions cannot be dismissed entirely. Terms in the budget equation for ozone were estimated from the aircraft measurements and the divergence of the ozone flux was found to be large compared to the flux at the surface divided by the boundary-layer height.Part of this work was carried out while a visitor at Risø National Laboratory, Denmark.The National Center for Atmospheric Research is sponsored by the National Science Foundation.     

基于风廓线雷达的对流边界层高度的确定

大气边界层高度对于天气、气候和大气污染研究是一个至关重要的参量。对流边界层(Convective Boundary Layer,CBL)顶部的夹卷过程造成温度和湿度垂直梯度增强,导致这一层的折射率结构常数C■变高。C■的这种垂直分布特征经常被用来定位出CBL高度Z_i。本文利用2010年7—8月天津大港的风廓线雷达数据推断出CBL高度Z_i,对于多重C■峰值或不明确的C■峰值,本文改进了对Z_i的测定,分别讨论了C■最大后向散射法与C■和垂直速度方差(σ■)相结合的新方法的适用性。研究显示:(1)C■廓线具有单峰时,最大后向散射强度法能正确估计CBL高度,这种情况往往对应的是晴天。CBL上存在的残留层或云层引起的温湿起伏变化导致C■廓线具有双峰甚至多峰时,最大后向散射强度法可能会错误估计CBL高度;(2)C■和σ■结合的方法不仅与晴天时C■最大后向散射法有较好的一致性,而且可以将CBL造成的C■峰值从云层造成的C■峰值中区分出来,从而正确估计CBL高度;(3)一般而言,对流边界层中存在有明显的、破碎或者分散不明显的云时,C■和σ■结合的方法都能较好地识别出CBL对应的C■峰值。但由于边界层中的情况极为复杂,C■和σ■结合法也会因不同的原因而错误估计CBL高度。     

Wind profile constants in a neutral atmospheric boundary layer over complex terrain

The roughness height z ₀ and the zero-plane displacement height d ₀ were determined for a region of complex terrain in the Pre-Alps of Switzerland. This region is characterized by hills of the order of 100 m above the valley elevations, and by distances between ridges of the order of 1 km; it lies about 20 to 30 km north from the Alps. The experimental data were obtained from radiosonde observations under near neutral conditions. The analysis was based on the assumption of a logarithmic profile for the mean horizontal wind existing over one half of the boundary layer. The resulting (z ₀/h) and (d ₀/h) (where h is the mean height of the obstacles) were found to be in reasonable agreement with available relationships in terms of placement density and shape factor of the obstacles, which were obtained in previous experiments with h-scales 2 to 4 orders of magnitude smaller than the present ones.     

Deriving characteristic parameters of the convective boundary layer from sodar measurements of the vertical velocity variance

This paper deals with the derivation of the convective mixing height and the characteristic convective velocity w _* from profiles of _w measured by sodar. The parameters were obtained by fitting an analytical profile to the observed data. Results were compared with values obtained by the meteorological preprocessor of a dispersion model and from noon radiosoundings. In addition, a Monte Carlo method was applied to study the influence of measurement errors. It turned out that it is inherently difficult to determine the depth of deep mixed layers from sodar measurements with a limited range, although the determination of w _* should be possible. However, a significant underestimation of _w , and thus w _*, was found, which is probably due to disproportional sampling of updrafts and downdrafts.     

Investigation of the planetary boundary layer height variations over complex terrain

The effects of sea-breeze interactions with synoptic forcing on the PBL height over complex terrain are investigated through the use of a 3-D mesoscale numerical model. Two of the results are as follows. First, steep PBL height gradients—order of 1500 m over a grid interval of 10 km — are associated with the sea-breeze front and are enhanced by the topography. Second, a significant horizontal shift in the maximum PBL height relative to the mountains, is induced by a corresponding displacement of the thermal ridge due to the mountains, in the presence of large scale flow.     

A parameterization of the nocturnal ozone reduction in the residual layer by verticla downward mixing during summer smog situations using sodar data

The reduction of ozone in the nocturnal residual layer by vertical mixing to the surface was investigated for several summer smog episodes on the Swiss plateau in the years 1990 and 1991. Using a limited data set of SODAR measurements and surface ozone concentrations, a parameterization of the ozone depletion in the nocturnal residual layer due to vertical mixing to the ground is proposed. This model is not intended to be physically complete but is rather simple with limited input information required. The nocturnal ozone reduction within the whole planetary boundary layer (nocturnal boundary layer plus residual layer) over the complex terrain of the Swiss plateau for the days investigated is between 20 and 50%.     

A sodar study of the temperature structure parameter in the convective boundary layer

From sodar measurements gathered during the Voves experiment (France, summer 1977), the variations of the temperature structure parameter C _T ² were studied in the morning planetary boundary layer. Dimensionless profiles of C _T ² are consistent with the mixed-layer scaling of Kaimal et al. (1976); however, for z < 0,5 z _i, the decrease of C _T ² as z ^4/3 should be weighted according to Frisch and Ochs (1975).When the final breakup of the nocturnal inversion is achieved, the variations of the maximum of the C _T ² profile are in good agreement with those predicted by Wyngaard and Le Mone (1980). Discrepancies are observed mainly when the mixed layer is shallow and mechanical turbulence is important compared with buoyancy-driven turbulence.     

Airborne measurements of turbulent trace gas fluxes and analysis of eddy structure in the convective boundary layer over complex terrain

Using the new high-frequency measurement equipment of the research aircraft DO 128, which is described in detail, turbulent vertical fluxes of ozone and nitric oxide have been calculated from data sampled during the ESCOMPTE program in the south of France. Based on airborne turbulence measurements, radiosonde data and surface energy balance measurements, the convective boundary layer (CBL) is examined under two different aspects. The analysis covers boundary-layer convection with respect to (i) the control of CBL depth by surface heating and synoptic scale influences, and (ii) the structure of convective plumes and their vertical transport of ozone and nitric oxides. The orographic structure of the terrain causes significant differences between planetary boundary layer (PBL) heights, which are found to exceed those of terrain height variations on average. A comparison of boundary-layer flux profiles as well as mean quantities over flat and complex terrain and also under different pollution situations and weather conditions shows relationships between vertical gradients and corresponding turbulent fluxes. Generally, NO_x transports are directed upward independent of the terrain, since primary emission sources are located near the ground. For ozone, negative fluxes are common in the lower CBL in accordance with the deposition of O₃ at the surface.The detailed structure of thermals, which largely carry out vertical transports in the boundary layer, are examined with a conditional sampling technique. Updrafts mostly contain warm, moist and NO_x loaded air, while the ozone transport by thermals alternates with the background ozone gradient. Evidence for handover processes of trace gases to the free atmosphere can be found in the case of existing gradients across the boundary-layer top. An analysis of the size of eddies suggests the possibility of some influence of the heterogeneous terrain in mountainous area on the length scales of eddies.     

Estimation of surface stress over a forest from sodar measurements and its use to parameterize the stable boundary-layer height

Sodar observations from three nights of the HAPEX-MOBILHY experiment have been used to compute covariances between single measurements of the three velocity components. From these, estimates of a low frequency friction velocityu _* are derived which show better correlation with observed values of the stable boundary layer (SBL) height,h, than directu _*-measurements by an ultrasonic anemometer. On the contrary, interdiurnal variability ofh is better correlated with directu _*-measurements. These findings should be mainly due to the problem of different spectral and spatial representativity of the twou _*-values.     

Non-local mixing of momentum in the convective boundary layer

Recently Frech and Mahrt proposed a closure scheme which includes alarge-scale stress term to represent the effects of non-local momentummixing in the convective boundary layer. Here large-eddy simulation (LES)datasets are used to evaluate the performance of this scheme across a rangeof stabilities between neutral and highly convective conditions, and as afunction of baroclinity. Generally the inclusion of the non-local term inthe closure model leads to results in better agreement with LES, althoughsome modifications to the model formulation are suggested.     

SWT声雷达探测系统对大气边界层声回波信号的变换与检测

在SWT声雷达探测系统中,采用作者提出的检测声回波信号的跟踪滤波锁相方法(PLTF),提取Doppler频偏f_d的V-F-BCD变换和模块化设计,减小了锁相环(PLL)的失锁现象,改善了声雷达的测风精度,闭路同源标定结果表明SWT声雷达探测系统的测频精度优于0.1Hz,相当于测风精度可达λ/4/s(λ——发射声波长),由于环境噪声的干扰,将会使测风精度略有降低。     

近山地区大气边界层声雷达回波的季节特征

本文根据北京附近某一近山地区冬季和夏季的声雷达探测结果,对比了大气边界层声雷达回波图象在季节上的相似性和差异,分析了冬夏逆温层和对流混合层的生消演变特征,并对声雷达回波图象的几种类型与边界层风廓线的关系作了初步探讨。     

Implementation of turbulent mixing over a stratocumulus-topped boundary layer and its impact in a GCM

The effect of a vertical diffusion scheme over a stratocumulus topped boundary layer (STBL) was investigated using the YONU AGCM (Yonsei University Atmospheric General Circulation Model). To consider the impact of clouds on the turbulence production, the turbulence mixing term, driven by radiative cooling at the cloud top, is implemented as an extended non-local diffiusion scheme. In the model with this new scheme, the STBL parameterization significantly influences the lower atmosphere over the tropical and...     

Convective characteristics of the nocturnal urban boundary layer as observed with Doppler sodar and Raman lidar

Convective plume patterns, characteristic of clear sky and light wind daytime boundary layers over land, were observed for two nights with a tri-axial Doppler sodar operated in the central area of Rome during the summer of 1994. An urban heat island effect, combined with a continuation of a breeze from the sea late into night during both days, is believed to be responsible for the observed nocturnal convection. Estimates of the surface heat flux and the vertical velocity scaling parameter are obtained from profiles of vertical velocity variance, and the Raman lidar water vapor measurements are used to obtain the humidity scaling parameter. Convective scaling results for vertical wind and humidity fairly agree with the results of other experiments and models. On the basis of available measurements, it appears that mixed-layer similarity formulations used to characterize the daytime convective boundary layer over horizontally homogeneous surfaces can also be applied to the nocturnal urban boundary layer during periods of reasonable convective activity.