Characterization of frozen soil-cement mixture for berm construction in cold regions

Lagoon berms in western Alaska are difficult to design and build due to limited resources, high cost of construction and materials, and warm permafrost conditions. This paper explores methods to treat locally available frozen materials and use them for berm construction. The goal is to find an optimized mix ratio for cement and additives that can be effective in increasing the strength and decreasing the thaw settlement of an ice-rich frozen silty soil. Soil of similar type and ice content to the permafrost found at a project site in Eek, Alaska is prepared in a cold room. The frozen soil is pulverized and cement, additives and fibers are added to the samples for enhancing shear strength and controlling thaw settlement. Thaw settlement and direct shear testsare performed to assess strength and settlement characteristics. This paper presents a sample preparation method, data from thaw settlement and direct shear tests, and analyses of the test results and preliminary conclusions.     

A study on dynamic shear strength on frozen soil-concrete interface

Using newly developed dynamic shearing devices, the dynamic shearing strength of frozen soil-concrete interface was studied experimentally. By placing concrete blocks in the lower half of the shear box and frozen soil sample in the upper part, a series of dynamic shear tests on their interfaces were carried out. The obtained results are summarized and the main influencing factors are revealed.     

Freezing and thawing effects of sand-silt mixtures on elastic waves

Freezing and thawing during the winter season change soil properties such as density. The density change in the particulate media influences soil stiffness. In addition, freezing of partially or fully saturated soils changes the soil matrix from a particulate media to a continuum. The goal of this study is to investigate the cyclic freezing and thawing effects on elastic waves. Sand-silt mixtures with 10% silt fraction in weight and 40% saturation are prepared. The sand-silt mixtures are placed in a nylon cell, onto which a pair of bender elements and a pair of piezoelectric disk elements are installed for the measurement of shear and compressional waves, respectively. The temperature of the mixtures decreases from 20°C to 10°C to freezing. The frozen sample is gradually thawed at room temperature (20°C). These freezing-thawing processes are repeated three times. The test result shows that the shear and compressional wave velocities significantly increase when the specimen is frozen. When the temperature is greater than 0°C, the elastic wave velocities are lower during thawing than during freezing due to soil structure change. This study demonstrates that soil structure change during the winter season may be effectively estimated from elastic waves.     

An experimental study on the relationship between acoustic parameters and mechanical properties of frozen silty clay

To study the influence of temperature and water content on ultrasonic wave velocity and to establish the relationship between ultrasonic wave velocity and frozen silty clay strength, ultrasonic tests were conducted to frozen silty clay by using RSM-SY5(T) nonmetal supersonic test meter, and the tensile strength and compressive strength of silty clay were measured under various negative temperatures. Test and analysis results indicate that, ultrasonic wave velocity rapidly changes in the temperature range of 1 °C to 5 °C. Ultrasonic wave velocity increased with an increase of water content until the water content reached the critical water content, while decreased with an increase of water content after the water content exceeded the critical water content. This study showed that there was strong positive correlation between the ultrasonic wave velocity and the frozen soil strength. As ultrasonic wave velocity increased, either tensile strength or compressive strength increased. Based on the experimental data, the relationship between ultrasonic wave velocity and frozen silty clay strength was obtained through regression analysis. It was found that the ultrasonic test technique can be used to test frozen soils and lay the foundation for the determination of frozen soil strength.     

A nonlinear interface structural damage model between ice crystal and frozen clay soil

The shear properties of ice-frozen soil interface are important when studying the constitutive model of frozen soil and slope stability in cold regions. In this research, a series of cryogenic direct shear tests for ice-frozen clay soil interface were conducted. Based on experimental results, a nonlinear interface structural damage model is proposed to describe the shear properties of ice-frozen clay soil interface. Firstly, the cementation and friction structural properties of frozen soil materials were analyzed, and a structural parameter of the ice-frozen clay soil interface is proposed based on the cryogenic direct shear test results. Secondly, a structural coefficient ratio is proposed to describe the structural development degree of ice-frozen clay soil interface under load, which is able to normalize the shear stress of ice-frozen clay soil interface,and the normalized data can be described by the Duncan-Chang model. Finally, the tangent stiffness of ice-frozen clay soil interface is calculated, which can be applied to the mechanics analysis of frozen soil. Also, the shear stress of ice-frozen clay soil interface calculated by the proposed model is compared with test results.     

Determination of long-term strength of frozen loess after numerous freeze-thaw cycles

In order to determine the changing rule of long-term frozen soil strength and elucidate the connection between long-term strength and soil physical properties,frozen loess was subjected to 4,6,8,10,and 50 freeze-thaw cycles,under closed-state conditions in a constant-temperature box.The frozen samples were tested on a spherical template indenter,and the results show that under the effect of repeated freeze-thaw cycles,the long-term strength of frozen loess decreased; changes in the mechanical property indices were highly unstable during the first 10 cycles; the soil strength and density were the greatest at the eighth cycle while the void ratio was the smallest; and after eight cycles all of the indices had less fluctuation and certain rising or falling tendencies.By converting the number of freeze-thaw cycles into elapsed time in the tests,three different forecasting methods of long-term soil strength could be assessed and the soil equivalent cohesive force after 10 years,20 years,or 30 years could be estimated.     

Coupling numerical simulation with remotely sensed information for the study of frozen soil dynamics

The acquisition of spatial-temporal information of frozen soil is fundamental for the study of frozen soil dynamics and its feedback to climate change in cold regions. With advancement of remote sensing and better understanding of frozen soil dynamics, discrimination of freeze and thaw status of surface soil based on passive microwave remote sensing and numerical simulation of frozen soil processes under water and heat transfer principles provides valuable means for regional and global frozen soil dynamic monitoring and systematic spatial-temporal responses to global change. However, as an important data source of frozen soil processes, remotely sensed information has not yet been fully utilized in the numerical simulation of frozen soil processes. Although great progress has been made in remote sensing and frozen soil physics, yet few frozen soil research has been done on the application of remotely sensed information in association with the numerical model for frozen soil process studies. In the present study, a distributed numerical model for frozen soil dynamic studies based on coupled water-heat transferring theory in association with remotely sensed frozen soil datasets was developed. In order to reduce the uncertainty of the simulation, the remotely sensed frozen soil information was used to monitor and modify relevant parameters in the process of model simulation. The remotely sensed information and numerically simulated spatial-temporal frozen soil processes were validated by in-situ field observations in cold regions near the town of Naqu on the East-Central Tibetan Plateau. The results suggest that the overall accuracy of the algorithm for discriminating freeze and thaw status of surface soil based on passive microwave remote sensing was more than 95%. These results provided an accurate initial freeze and thaw status of surface soil for coupling and calibrating the numerical model of this study. The numerically simulated frozen soil processes demonstrated good performance of the distributed numerical model based on the coupled water-heat transferring theory. The relatively larger uncertainties of the numerical model were found in alternating periods between freezing and thawing of surface soil. The average accuracy increased by about 5% after integrating remotely sensed information on the surface soil. The simulation accuracy was significantly improved, especially in transition periods between freezing and thawing of the surface soil.     

环境气候条件下土壤冻融过程中湿热耦合作用模型研究

基于Harlan模型和Darcy定律,综合考虑环境气候因素和水热特征参数对湿热迁移影响,建立了环境气候条件下季节性冻土区土壤冻融过程中湿热耦合作用模型.根据地表能量交换平衡原理推导出边界条件.依据实测数据回归分析出土壤湿热特征参数表达式.采用全隐式有限差分格式和TDMA迭代法对内蒙古锡林浩特地区冻结期间土壤湿热迁移规律进行了数值模拟.温度计算值和实测值比较一致,最大误差不超过2.5℃,说明该模型具有较高的准确性.利用该模型仅通过气象资料和湿热特征参数就可预测季冻区土壤冻胀和田间湿热分布状况并能够用来指导农田工程建设和农业生产.     

Evaluation of creep models for frozen soils

To model the creep behavior of frozen soils, three creep stages have to be reasonably described (i.e., primary, secondary and tertiary stages). Based on a series of uniaxial creep test results, three creep models were evaluated. It was shown that hypoplastic creep model has high prediction accuracy for both creep strain and strain rate in a wide stress range. The elementary rheological creep model can only be used for creep strains at low stress levels, because of the restraints of its mathematical construction. For the soft soil creep model, the progressive change from the primary to secondary and tertiary stages cannot be captured at high stress levels. Therefore, the elementary rheological and soft soil creep models can only be used for low stress levels without a tertiary stage; while the hypoplastic creep model is applicable at high stress levels with the three creep stages.     

东北黑土区土壤剖面地温和水分变化规律

东北黑土区土壤侵蚀的结果使土壤在坡面上发生再分配,土壤腐殖质层厚度的空间变异增大。腐殖质层厚度的变化又引起地温和土壤水分等土壤物理性质的变化,地温和水分是影响和反映冻融侵蚀作用的重要因子,也是影响地表和土壤剖面物质运移的重要因素。本文通过实测不同厚度腐殖质层剖面的地温和土壤水分,分析了地温和水分随时间和土壤剖面深度的变化规律。结果显示腐殖质层厚度对土壤温度和含水量有显著影响,腐殖质层较厚的剖面解冻速度比薄层黑土区要慢,不同深度土层温度到达0℃的日期也不相同,腐殖质层较厚的剖面冻结时间要滞后1周左右。同时,腐殖质层较厚的黑土区土壤含水量明显大于薄层黑土区,土壤水分运移的深度范围也大。     

Numerical simulation and experimental validation of moisture-heat coupling for saturated frozen soils

In seasonally frozen regions, freezing-and-thawing action is the main cause responsible for the destruction of canals, which is closely linked to the temperature gradient and water transport. To investigate the behaviour of soils under freezing-and-thawing actions, many numerical models have been established that consider the important coupling of moisture transport and temperature evolution; but they contain excessive parameters, some of which are rather difficult to determine. Based on the well-known Harlan''s theory, a simple moisture-heat coupling model was recently proposed to quantify the coupled moisture-heat transport performance of soils in terms of the central temperature and porosity. The mathematical module of COMSOL Multiphysics was further employed to solve the governing equations numerically. To validate our model, a thorough experimental scheme was carried out in our lab. The measured temperature distribution was found to be consistent with the predicted results.     

Constitutive models and salt migration mechanisms of saline frozen soil and the-state-of-the-practice countermeasures in cold regions

A series of saline soil-related problems, including salt expansion and collapse, frost heave and thaw settlement, threaten the safety of the road traffic and the built infrastructure in cold regions. This article presents a comprehensive review of the physical and mechanical properties, salt migration mechanisms of saline soil in cold environment, and the countermeasures in practice. It is organized as follows:(1) The basic physical characteristics;(2) The strength criteria and constitutive models;(3) Water and salt migration characteristics and mechanisms; and(4) Countermeasures of frost heave and salt expansion. The review provides a holistic perspective for recent progress in the strength characteristics, mechanisms of frost heave and salt expansion, engineering countermeasures of saline soil in cold regions. Future research is proposed on issues such as the effects of salt erosion on concrete and salt corrosion of metal under the joint action of evaporation and freeze-thaw cycles.     

Experimental research on acoustic wave velocity of frozen soils during the uniaxial loading process

Ultrasonic P-wave tests of frozen silt and frozen sand were conducted during uniaxial loading by using an RSM^®-SY5(T) nonmetal ultrasonic test meter to study the velocity characteristics of P-waves. The experimental results indicate that the P-wave velocity is affected by soil materials, temperature, and external loads, so the P-wave velocity is different in frozen silt and frozen sand, but all decrease with an increase of temperature and increase at first and then decrease with strain during the loading process. There is an exponential relationship between uniaxial compressive strength and P-wave velocity, and the correlation between them is very good. The characteristic parameters of acoustic waves can, to some extent, reflect the development of internal cracks in frozen soils during loading.     

1960-2015年新疆塔什库尔干河谷季节性冻土对气候变化的响应

利用1960-2015 年新疆塔什库尔干河谷季节性冻土的冻结始日、冻结终日、年冻结日数、年累积冻土厚度、最大冻土深度等特征指标资料,采用气候倾向率、气候突变、气候变化趋势的持续性等方法,分析近56 a该地区季节性冻土的年际、年代际变化特征。研究发现：（1）在全球变暖的背景下,1960-2015 年新疆塔什库尔干河谷气温变化亦呈上升趋势,升温趋势的持续性较强,升温幅度0.03 ℃·a^-1、0.29 ℃·（10 a）^-1、0.74 ℃·（30 a）^-1。（2）在1960-2015年期间,该地区季节性冻土呈退化趋势,具体表现为;冻结始日推迟,冻结终日提前,年冻结日数减少,年累积冻土厚度减小,最大冻土深度减小。（3）在1960-2015年期间,该地区季节性冻土持续退化趋势持续性强。（4）1960-2015 年新疆塔什库尔干河谷季节性冻土对气温变暖的具体响应呈现为退化状态。（5）按气候升温率Gt;0.034~0.046 ℃·a^-1 计算,在气候变暖背景下,该地区季节性冻土到2050 年（较2000 年）的冻结始日将推迟12~15 d、年冻结日数将减少21~27 d、年累积冻土厚度将减少36.3%~46.7%。     

Status and prospects of frozen soft studies using CT technology

This paper introduces the characteristics of Computed Tomography （CT） technology and reviews its history, current situation, representative achievements, and use of using CT technology on frozen soil study, including auxiliary equipment specially de- signed for frozen soil studies. CT numbers are used to analyze frozen soil internal structure change, defining and exploring dam- age evolution, and use of CT images on observing soil mesostructure. Finally, this paper presents existing problems confronted by using CT in frozen soil studies, possible solutions and challenges, among which, we introduce high quality CT image processing for frozen soils, and relations between CT number change and each component change on frozen soil samples within the region of interest. It is shown that present CT technology is one of the most ideal and effective technology to study frozen soil mesostructure using non-desmactive testing. CT technology will play a key role in the study and development in the field of frozen soil by means of auxiliary equipment and the digital imaging processing.     

Laboratory investigation on the mechanical behavior of ice-saturated frozen loess

To investigate the mechanical properties of ice-saturated frozen soil, a series of triaxial tests under various confining pressures（0.5 to 9.0 MPa） on ice-saturated frozen loess with ice content of 23.7% were carried out at a temperature-6 °C, and at 1.25 mm/min of loading rate. The triaxial tests include two loading modes, one with monotonic loading（i.e., triaxial compression）, and another with static cycle loading. The test results under triaxial compression show that the strength and deformation behaviors of ice-saturated frozen loess are affected by confining pressure. According to the test results of triaxial loading-unloading cycle test, the elastic modulus evolution with the number of cycles under different confining pressures are analyzed.     

Status and prospects of frozen soil studies using CT technology

This paper introduces the characteristics of Computed Tomography (CT) technology and reviews its history, current situation, representative achievements, and use of using CT technology on frozen soil study, including auxiliary equipment specially designed for frozen soil studies. CT numbers are used to analyze frozen soil internal structure change, defining and exploring damage evolution, and use of CT images on observing soil mesostructure. Finally, this paper presents existing problems confronted by using CT in frozen soil studies, possible solutions and challenges, among which, we introduce high quality CT image processing for frozen soils, and relations between CT number change and each component change on frozen soil samples within the region of interest. It is shown that present CT technology is one of the most ideal and effective technology to study frozen soil mesostructure using non-destructive testing. CT technology will play a key role in the study and development in the field of frozen soil by means of auxiliary equipment and the digital imaging processing.     

Impacts of snow cover and frozen soil in the Tibetan Plateau on summer precipitation in China

This paper presents an analysis of the mechanisms and impacts of snow cover and frozen soil in the Tibetan Plateau on the summer precipitation in China, using RegCM3 version 3.1 model simulations. Comparisons of simulations vs. observations show that RegCM3 well captures these impacts. Results indicate that in a more-snow year with deep frozen soil there will be more precipitation in the Yangtze River Basin and central Northwest China, western Inner Mongolia, and Xinjiang, but less precipitation in Northeast China, North China, South China, and most of Southwest China. In a less-snow year with deep frozen soil, however, there will be more precipitation in Northeast China, North China, and southern South China, but less precipitation in the Yangtze River Basin and in northern South China. Such differences may be attributed to different combination patterns of melting snow and thawing frozen soil on the Plateau, which may change soil moisture as well as cause differences in energy absorption in the phase change processes of snow cover and frozen soil. These factors may produce more surface sensible heat in more-snow years when the frozen soil is deep than when the frozen soil is shallow. The higher surface sensible heat may lead to a stronger updraft over the Plateau, eventually contributing to a stronger South Asia High and West Pacific Subtropical High. Due to different values of the wind fields at 850 hPa, a convergence zone will form over the Yangtze River Basin, which may produce more summer precipitation in the basin area but less precipitation in North China and South China. However, because soil moisture depends on ice content, in less-snow years with deep frozen soil, the soil moisture will be higher. The combination of higher frozen soil moisture with latent heat absorption in the phase change process may generate less surface sensible heat and consequently a weaker updraft motion over the Plateau. As a result, both the South Asia High and the West Pacific Subtropical High will be weaker, hence causing more summer precipitation in northern China but less in southern China.     

Effect of cryostructures on the uniaxial compressive strength of frozen clay

Unconfined uniaxial compressive tests were performed to study the influence of cryostructure on frozen clay's behavior,such as strain-stress,compressive strength,and failure characteristics,at temperatures varying from-10 to-2°C and strain rates varying from 1.0×10-5to 1.0×10-3s-1.Artificial samples were prepared of three types:(1)integral structure,(2)laminar structure,and(3)reticular structure.The impact of temperature,strain rate,and cryostructure on the mechanical properties is discussed.In general,frozen clay with various cryostructures shows strain-softening behavior in the range of testing temperatures and strain rates.For frozen clay of different cryostructures,the ultimate compressive strength increases with increasing strain rate and decreasing temperature.Under the same testing conditions,the ultimate compressive strengths from high to low are in integral samples,laminar samples,and reticular samples.Failure strain of frozen clay generally increases with increasing temperature and does not indicate any correlation with cryostructure or strain rate.The failure mode of integral and reticular samples was shear failure,while laminar samples showed tensile failure.     

Characteristics of dynamic strain and strength of frozen silt under long-term dynamic loading

The dynamic strain and strength of frozen silt under long-term dynamic loading are studied based on creep tests. Three groups of tests are performed (Groups I, II, and III). The initial deviator stresses of Groups I and II are same and the dynamic stress amplitude of Group II is twice as that of Group I. The minimum value of dynamic stress in Group III is near zero and its dynamic stress amplitude is larger than those of Groups I and II. In tests of all three groups there are similar change trends of accumulative strain, but with different values. The accumulative strain curves consist of three stages, namely, the initial stage, the steady stage, and the gradual flow stage. In the tests of Groups I and II, during the initial stage with vibration times less than 50 loops the strain amplitude decreased with the increase of vibration times and then basically remained constant, fluctuating in a very small range. For the tests of Group III, during the initial and steady stages the strain amplitude decreased with the increase of vibration times, and then increased rapidly in the gradual flow stage. The dynamic strength of frozen silt decreases and trends to terminal dynamic strength as the vibration times of loading increase.