黏滞阻尼器耗能减振工程应用设计方法研究

本中文阐述了黏滞阻尼器的构造、力学模型以及其耗能减振的基本原理,并基于国际结构振动控制公共平台Benchmark模型,采用ANSYS和SAP2000有限元软件对其进行无控和有控地震反应分析,研究了黏滞阻尼器自身参数、设置形式、速度指、阻尼系数、位置和数量等因素对其控制效果的影响规律.结合国内外规范,给出LVD安装形式、...     

三种阻尼减振结构抗震性能的对比分析

对设置两种新型摩擦阻尼器(T形芯板摩擦阻尼器和拟粘滞摩擦阻尼器)和粘滞阻尼器的单自由度结构及多层实际工程结构进行了时程分析研究。结果表明，一方面三种阻尼器都能有效地控制结构的反应，另一方面T形芯板摩擦阻尼器的位移控制效果略好于拟粘滞摩擦阻尼器，但是后者的加速度控制效果好于前者。     

基于耗能连梁钢板阻尼器的高层结构耗能减振分析及应用

为改善传统连梁钢板阻尼器的适用性,提出了一种新型耗能连梁钢板阻尼器的设计方法,通过对阻尼器工作区域的划分与设计,使新型阻尼器充分发挥耗能作用,有效地提高了结构整体耗能能力。基于有限元软件ABAQUS模拟低周反复荷载作用下墙肢与阻尼器的应力应变状态,以验证所提出的新型阻尼器的设计方法及端部嵌固区的可靠性,并通过对原结构和实施耗能连梁钢板阻尼器结构进行弹塑性时程分析,探讨其改进后的抗震性能。研究结果表明,新型嵌固区构造不仅能够保证阻尼器与墙肢协同工作良好,还能大大降低施工难度;通过实施该阻尼器,可形成耗能连梁及抗震多道防线,在连梁钢筋混凝土部分损伤较为严重的情况下,仍能保证连梁具有一定的延性和耗能能力。     

渡槽结构隔震耗能减振控制的试验研究

本文在理论分析的基础上，对设计中的南水北调中线工程北京段南泉河水大型渡槽工程结构，按几何相似比1：10研制了结构模型及多组隔震耗能混合减振支座，在振动台上成功地进行了多工况的地震模拟试验。试验结果表明：将由隔震器与阻尼器组成的隔震耗能混合减振支座应用于渡槽结构，可以有效地减小渡槽结构的地震响应。此外，所研制的隔震耗能混合减振支座，在实际结构工程中的施工简单可行。     

基于Benchmark模型的抑制屈曲支撑耗能减振作用分析

抑制屈曲支撑可在拉压循环荷载作用下均达到屈服,拉压承载力基本一致,滞回曲线稳定饱满,耗能能力强。基于Benchmark模型对安装抑制屈曲支撑的钢框架结构基于ANSYS的数值分析表明,抑制屈曲支撑不仅可使结构在小震时的抗侧刚度有所提高,同时在大震时通过其往复滞回变形发挥耗能减振作用,大大地降低了结构的地震响应,提高了结构的抗震性能。同时分析表明考虑高阶振型影响的能力谱分析方法是一种更为精确的分析方法。     

网壳结构的粘滞阻尼减振分析与试验研究

本文将粘滞阻尼器引入网壳结构,针对网壳结构粘滞阻尼器减振系统,编制了有限元分析程序,并对网壳结构进行了大量的振动控制分析和计算。作者设计制做了适合网壳结构的粘滞阻尼器,进行了性能试验;在此基础上设计制作了一个球型网壳结构模型,并进行了粘滞阻尼器减振的地震模拟振动台试验。     

网壳结构的粘弹阻尼器减振分析

本文将粘弹阻尼器引入网壳结构，针对网壳结构粘弹阻尼器减振系统，编制了有限元分析程序，利用该程序对单层球面网壳和单层柱面网壳进行了大量的减振分析。计算结果表明，粘弹阻尼器减振系统对大跨网壳结构的减振效果是十分明显的，是一种适合大跨网壳结构的减振系统。     

斜拉桥纵向设置粘滞阻尼器参数分析

采用Maxwell阻尼模型模拟了粘滞阻尼器的滞回耗能特性。通过对设置粘滞阻尼器斜拉桥纵向非线性地震反应的分析，讨论了粘滞阻尼器各参数对结构地震响应的影响，并通过计算证实了粘滞阻尼器具有良好的消能减振效果。     

基于几何非线性的Pall型摩擦阻尼器滞回特性分析与试验验证

本文从Palll摩擦阻尼器四连杆机构的几伺非线性变形特征出发,分析一种改进的Pall摩擦阻尼器--T形芯板摩擦阻尼器的滞回特性以及支撑的受力特点.本文与不考虑几何非线性的简化计算方法得到完全不同的结论:支撑的拉力在阻尼器起滑后并不保持为一常数,而是呈显著增加趋势,支撑最大拉力可达起滑时的2～3倍.试验结果也充分验证了这一结论.这一结论意味着按传统简化计算方法设计的Pall阻尼结构可能存在较大安全隐患.     

单层柱面网壳的粘滞阻尼器减振分析

采用粘滞阻尼器减振系统对单层柱面网壳的减振效果进行了较为系统的分析，分别考虑了阻尼系数C0、结构自身阻尼比ζ、屋面质量和结构自身刚度对结构减振系数δ的影响，同时考察了设置阻尼器的数目以及阻尼器的位置的影响。通过较大规模参数化分析，基本了解了粘滞阻尼器减振系统在单层柱面网壳中的减振规律。     

大跨径拱桥被动减震控制的仿真分析

本文采用现代控制理论对设有耗能减震装置的拱桥结构进行被动减震控制仿真分析,给出了大跨度拱桥在多点激励下的运动微分方程,将拱桥简化成平面杆系模型,给出减震结构的状态方程,然后基于SIMULINK环境下对设有粘滞阻尼器的拱桥减震结构进行动态仿真分析,并考虑了行波效应对减震效果的影响。该方法较之传统的分析方法更简便、有效,分析结果表明设置了耗能器的拱桥结构地震反应有明显的降低。     

A study on using wide‐flange section web under out‐of‐plane flexure for passive energy dissipation

It is not common to purposely subject the web of wide‐flange or I‐sections to out‐of‐plane bending. However, yielding the web under this loading condition can be a stable source of energy dissipation as the transition at the corner from the web to the flanges is smooth and weld‐free; this prevents stress concentrations causing premature failure and eliminates uncertainties and imperfections associated with welding. Further, short segments of wide‐flange or I‐sections constitute a simple and inexpensive energy dissipating device as minimum manufacturing is required and leftovers not useful for other structural purposes can be re‐utilized. This paper proposes a new type of seismic damper in the form of braces based on yielding the web of short length segments of wide‐flange or I‐shaped steel sections under out‐of‐plane bending. The hysteretic behavior and ultimate energy dissipation capacity is investigated via component tests under cyclic loads. The experimental results indicate that the damping device has stable restoring force characteristics and a high energy dissipation capacity. Based on these results, a simple hysteretic model for predicting the load–displacement curve of the seismic damper is proposed, along with a procedure for predicting its ultimate energy dissipation capacity and anticipating its failure under arbitrarily applied cyclic loads. The procedure considers the influence of the loading path on the ultimate energy dissipation capacity. Finally, shaking table tests on half‐scale structures are conducted to further verify the feasibility and effectiveness of the new damper, and to assess the accuracy of the hysteretic model and the procedure for predicting its failure. Copyright © 2010 John Wiley & Sons, Ltd.     

基于无能源磁摩擦控制装置的被动智能控制研究

将无能源磁摩擦控制装置应用于结构被动智能控制。分析了无能源磁摩擦控制装置的恢复力特性及影响参数，建立了被动连续变刚度体系的理论模型，推导了受控结构系统的一般方程，进行了模型结构的被动智能控制仿真分析。从理论上验证了无能源磁摩擦控制装置用于结构被动智能控制具有良好的控制效果。     

基于ANSYS的木框架有限元静力弹塑性分析

采用大型有限元软件ANSYS10.0对单调水平荷载作用下一榀门式木框架及其各种加固方案进行了静力弹塑性计算分析。通过各种加固方式屈服荷载、极限荷载大小的比较以及相对于未加固木框架提高程度的比较,从中得出了对门式木框架加固的最佳方案,为木柱、梁-土坯组合墙体的抗震加固提供方案。     

Experimental evaluation of dynamic characteristics of seesaw energy dissipation system for vibration control of structures

Seesaw energy dissipation system (SEDS), a vibration control system used to provide enhanced seismic protection, has been proposed and investigated numerically. Because of its complicated arrangement, verification experiments are necessary to demonstrate the SEDS damping capacity. This paper presents the results of experimental investigation of the SEDS using fluid viscous dampers. Free vibration tests are conducted to demonstrate the SEDS damping capacity. Results of the free vibration test show that the SEDS has sufficient damping capacity for reduction of the seismic response of the frames. Parametric experimental investigations of the SEDS were conducted, the results of which demonstrate the effects of the system parameter on the damping capacity. Copyright © 2014 John Wiley & Sons, Ltd.     

Semi-active model predictive control for 3rd generation benchmark problem using smart dampers

A semi-active strategy for model predictive control (MPC), in which magneto-rheological dampers are used as an actuator, is presented for use in reducing the nonlinear seismic response of high-rise buildings. A multi-step predictive model is developed to estimate the seismic performance of high-rise buildings, taking into account of the effects of nonlinearity, time-variability, model mismatching, and disturbances and uncertainty of controlled system parameters by the predicted error feedback in the multi-step predictive model. Based on the predictive model, a Kalman-Bucy observer suitable for semi-active strategy is proposed to estimate the state vector from the acceleration and semi-active control force feedback. The main advantage of the proposed strategy is its inherent stability, simplicity, on-line real-time operation, and the ability to handle nonlinearity, uncertainty, and time-variability properties of structures. Numerical simulation of the nonlinear seismic responses of a controlled 20-story benchmark building is carried out, and the simulation results are compared to those of other control systems. The results show that the developed semi-active strategy can efficiently reduce the nonlinear seismic response of high-rise buildings.     

黏滞阻尼器对拉索参数振动的控制分析

提出采用黏滞阻尼器对拉索参数振动进行控制,建立了黏滞阻尼器控制拉索参数振动的运动方程。从频域和时域以及起振幅值等角度,研究了最优黏滞阻尼器对不同垂度拉索参数振动的控制效果;此外,还研究了最优黏滞阻尼器安装位置对拉索参数振动控制效果的影响。研究表明,黏滞阻尼器可以有效控制拉索的参数振动,控制效果与拉索的激励幅值、最优阻尼器的安装位置和斜拉索的垂度有关。激励幅值越大,控制效果一般越差;最优阻尼器的安装位置越靠近跨中,则控制效果越好;黏滞阻尼器对大垂度拉索的控制效果不及对小垂度拉索的控制效果。     

摩擦与粘性流体耗能器串联体系动力分析

采用粘性屈服模型来模拟摩擦耗能器的力－速度关系，建立了摩擦与粘性流体耗能器串联耗能体系的动力分析方法．为考虑框架杆件和支撑材料的几何非线性，采用增量型Ｒｏｓｅｎｂｒｏｃｋ二级三阶半隐式Ｒｕｎｇｅ－Ｋｕｔｔａ法求解动力方程．比较了仅有摩擦耗能器体系与串联组合耗能体系的减振效果，分析了粘性流体耗能器参数对组合耗能体系减振效果的影响。     

Dynamic analysis method of a combined energy dissipation system and its experimental verification

A combined energy dissipation system is developed in this paper. In this system lead rubber dampers and their parallel connection with oil dampers are used in the braces of a structural frame. A dynamic analysis method of the system, including the modelling of the lead rubber damper and the oil damper, is proposed. In the analysis method, the restoring force characterestics of the lead rubber damper is simulated by the Bouc–Wen hysteretic model, and the behaviour of the oil damper is simulated by a velocity and displacement‐related model in which the contributions of the oil damper to the damping force and stiffness of the system are considered. A series of shaking table tests of a three‐storey steel frame with the combined energy dissipation system are carried out to evaluate the performance of the system and to verify the analysis method. The test and analysis show that the performance of the combined energy dissipation system is quite satisfactory and there is a good agreement between the analysis and test results, which indicates that the analysis method proposed in this paper is valid and suitable for the dynamic analysis of the combined energy dissipation system. Copyright © 2002 John Wiley & Sons, Ltd.