Correction of Single Log-Derived Temperatures in the Danish Central Graben,North Sea

An equation for correcting log-derived temperatures measured at well depths between 1200 and 5400 m has been derived by comparing log-derived temperatures from wells in the Danish Central Graben (North Sea) with DST temperatures, from the same wells, that are believed to represent true formation temperatures. Equations developed previously using data over different depth ranges from Malaysia and Mexico yield fair results when applied to the North Sea. However, a better fit to the Danish data was obtained using new equations that are similar to those published in the earlier studies. The correction method here is based principally on time since end of circulation (TSC), but it also includes a small dependence on depth. In this study the true subsurface temperature (T_true) (°C) is given by where the correction factor f = 3.07·TSC^(–0.09)/(0.47·Z^(0.175)), T_surf is the seafloor temperature in °C, T_meas is the measured log temperature in °C, TSC is in hours, and Z is the depth below seafloor in meters. When TSC is not known, maximum probable, minimum probable, and most likely values can be estimated from the observed trend of TSC with depth.An estimate of the uncertainty in the corrected temperature can be obtained from the equation where is the standard deviation of the error in the correction factor f. This approach can be modified to include the additional uncertainty associated with unspecified TSC.     

Evaluation of Horner plot-corrected log-derived temperatures in the Danish Central Graben,North Sea

A small dataset comprising all temperature available data from reliable Horner plots from the Danish Central Graben was examined. Temperatures obtained by extrapolation using standard Horner plots were determined to be lower than true formation temperatures, as interpreted from DST data. Excellent agreement between true formation temperatures and Horner plot temperatures was achieved when the Horner plot temperatures (T_HP) were corrected upward by an amount proportional to the slope (A) of the Horner plot using the equation where the temperatures and the slope are in degrees Celsius. The standard deviation of the error in the corrected Horner plot temperatures was 2.1°C, indicating that this method is consistent. Further studies using larger numbers of Horner plots from a variety of geographic areas should be carried out to test and refine the hypotheses presented here. Efforts also should be made to understand the causes of variability in slopes of Horner plots.     

Impact of normal faulting and pre‐rift salt tectonics on the structural style of salt‐influenced rifts: the Late Jurassic Norwegian Central Graben,North Sea

Studies of salt‐influenced rift basins have focused on individual or basin‐scale fault system and/or salt‐related structure. In contrast, the large‐scale rift structure, namely rift segments and rift accommodation zones and the role of pre‐rift tectonics in controlling structural style and syn‐rift basin evolution have received less attention. The Norwegian Central Graben, comprises a complex network of sub‐salt normal faults and pre‐rift salt‐related structures that together influenced the structural style and evolution of the Late Jurassic rift. Beneath the halite‐rich, Permian Zechstein Supergroup, the rift can be divided into two major rift segments, each comprising rift margin and rift axis domains, separated by a rift‐wide accommodation zone – the Steinbit Accommodation Zone. Sub‐salt normal faults in the rift segments are generally larger, in terms of fault throw, length and spacing, than those in the accommodation zone. The pre‐rift structure varies laterally from sheet‐like units, with limited salt tectonics, through domains characterised by isolated salt diapirs, to a network of elongate salt walls with intervening minibasins. Analysis of the interactions between the sub‐salt normal fault network and the pre‐rift salt‐related structures reveals six types of syn‐rift depocentres. Increasing the throw and spacing of sub‐salt normal faults from rift segment to rift accommodation zone generally leads to simpler half‐graben geometries and an increase in the size and thickness of syn‐rift depocentres. In contrast, more complex pre‐rift salt tectonics increases the mechanical heterogeneity of the pre‐rift, leading to increased complexity of structural style. Along the rift margin, syn‐rift depocentres occur as interpods above salt walls and are generally unrelated to the relatively minor sub‐salt normal faults in this structural domain. Along the rift axis, deformation associated with large sub‐salt normal faults created coupled and decoupled supra‐salt faults. Tilting of the hanging wall associated with growth of the large normal faults along the rift axis also promoted a thin‐skinned, gravity‐driven deformation leading to a range of extensional and compressional structures affecting the syn‐rift interval. The Steinbit Accommodation Zone contains rift‐related structural styles that encompass elements seen along both the rift margin and axis. The wide variability in structural style and evolution of syn‐rift depocentres recognised in this study has implications for the geomorphological evolution of rifts, sediment routing systems and stratigraphic evolution in rifts that contain pre‐rift salt units.     

Salt thickness and composition influence rift structural style,northern North Sea,offshore Norway

“Salt” giants are typically halite‐dominated, although they invariably contain other evaporite (e.g. anhydrite, bittern salts) and non‐evaporite (e.g. carbonate, clastic) rocks. Rheological differences between these rocks mean they impact or respond to rift‐related, upper crustal deformation in different ways. Our understanding of basin‐scale lithology variations in ancient salt giants, what controls this and how this impacts later rift‐related deformation, is poor, principally due to a lack of subsurface datasets of sufficiently regional extent. Here we use 2D seismic reflection and borehole data from offshore Norway to map compositional variations within the Zechstein Supergroup (ZSG) (Lopingian), relating this to the structural styles developed during Middle Jurassic‐to‐Early Cretaceous rifting. Based on the proportion of halite, we identify and map four intrasalt depositional zones (sensu Clark et al., Journal of the Geological Society, 1998, 155, 663) offshore Norway. We show that, at the basin margins, the ZSG is carbonate‐dominated, whereas towards the basin centre, it becomes increasingly halite‐dominated, a trend observed in the UK sector of the North Sea Basin and in other ancient salt giants. However, we also document abrupt, large magnitude compositional and thickness variations adjacent to large, intra‐basin normal faults; for example, thin, carbonate‐dominated successions occur on fault‐bounded footwall highs, whereas thick, halite‐dominated successions occur only a few kilometres away in adjacent depocentres. It is presently unclear if this variability reflects variations in syn‐depositional relief related to flooding of an underfilled presalt (Early Permian) rift or syn‐depositional (Lopingian) rift‐related faulting. Irrespective of the underlying controls, variations in salt composition and thickness influenced the Middle Jurassic‐to‐Early Cretaceous rift structural style, with diapirism characterising hangingwall basins where autochthonous salt was thick and halite‐rich and salt‐detached normal faulting occurring on the basin margins and on intra‐basin structural highs where the salt was too thin and/or halite‐poor to undergo diapirism. This variability is currently not captured by existing tectono‐stratigraphic models largely based on observations from salt‐free rifts and, we argue, mapping of suprasalt structural styles may provide insights into salt composition and thickness in areas where boreholes are lacking or seismic imaging is poor.     

Seismic geomorphology and origin of diagenetic geobodies in the Upper Cretaceous Chalk of the North Sea Basin (Danish Central Graben)

Kilometre‐scale geobodies of diagenetic origin have been documented for the first time in a high‐resolution 3D seismic survey of the Upper Cretaceous chalks of the Danish Central Graben, North Sea Basin. Based on detailed geochemical, petrographic and petrophysical analyses, it is demonstrated that the geobodies are of an open‐system diagenetic origin caused by ascending basin fluids guided by faults and stratigraphic heterogeneities. Increased amounts of porosity‐occluding cementation, contact cement and/or high‐density/high‐velocity minerals caused an impedance contrast that can be mapped in seismic data, and represent a hitherto unrecognized, third type of heterogeneity in the chalk deposits in addition to the well‐known sedimentological and structural features. The distribution of the diagenetic geobodies is controlled by porosity/permeability contrasts of stratigraphic origin, such as hardgrounds associated with formation tops, and the feeder fault systems. One of these, the Top Campanian Unconformity at the top of the Gorm Formation, is particularly effective and created a basin‐wide barrier separating low‐porosity chalk below from high‐porosity chalk above (a Regional Porosity Marker, RPM). It is in particular in this upper high‐porosity unit (Tor and Ekofisk Formations) that the diagenetic geobodies occur, delineated by “Stratigraphy Cross‐cutting Reflectors” (SCRs) of which eight different types have been distinguished. The geobodies have been interpreted as the result of: (i) escaping pore fluids due to top seal failure, followed by local mechanical compaction of high‐porous chalks, paired with (ii) ascension of basinal diagenetic fluids along fault systems that locally triggered cementation of calcite and dolomite within the chalk, causing increased contact cements and/or reducing porosity. The migration pathway of the fluids is marked by the SCRs, which are the outlines of high‐density bodies of chalk nested in highly porous chalks. This study, thus, provides new insights into the 3D relationship between fault systems, fluid migration and diagenesis in chalks and has important applications for basin modelling and reservoir characterization.     

Relay ramp evolution and mass flow deposition (Upper Kimmeridgian–Lower Volgian) in the Tail End Graben, Danish North Sea

The Central Graben in the Danish North Sea sector consists of a series of N–S to NW–SE trending, eastward‐tilted half‐grabens, bound to the east by the Coffee Soil Fault zone. This fault zone has a complex Jurassic history that encompasses at least two fault populations; N–S to NNW–SSE striking faults active in the Late Aalenian–Early Oxfordian, and NNW–SSE to WNW–ESE striking faults forming in Late Kimmeridgian time (sensu gallico), following a short period of tectonic quiescence. Sediment transport across the Coffee Soil Fault zone was controlled by fault array evolution, and in particular the development of relay ramps that formed potential entry points for antecedent drainage systems from the Ringkøbing–Fyn High east of the rift. Fault and isochore trends of the Upper Kimmeridgian–Lower Volgian succession in the northeast Danish Central Graben show that accommodation space was initially generated close to several minor, isolated or overlapping faults. Subsidence became focused along a few master faults in the Early Volgian through progressive linkage of selected faults. Seismic time isochore geometries, seismic facies, amplitude trends and well ties indicate the presence of coarse clastic lithologies locally along the fault zone. The deposits probably represent submarine mass flow deposits supplied from footwall degradation and possibly also from the graben hinterland via a relay ramp. The latter source appears to have been cut off as the relay ramp was breached and the footwall block are uplifted. Fault growth and linkage processes thus controlled the spatial and temporal trends of accommodation space generation and sediment supply to the rift basin.     

Mid-Jurassic through mid-Cretaceous extension in the Central Graben of the North Sea - part 1: estimates from subsidence

Abstract The post early Carboniferous subsidence history of the Central North Sea basin can be separated into three major periods: Permian, Triassic and post Mid-Jurassic. Prior efforts to account for this subsidence within an extensional framework have concentrated on the post Mid-Jurassic. These efforts have assumed that the effects of the previous periods of extension necessary to create the Permian and Triassic subsidence are negligible. We consider the 80-km value for the Mid-Jurassic-mid-Cretaceous extension from these efforts a reasonable upper estimate of the likely amount of extension. This value has received considerable criticism as it is almost four times as great as that determined by summing the horizontal displacement (heave) on faults observed on industry seismic lines in the area.
We treat the two earlier phases of extension as one phase and develop a method to estimate the maximum value of this extension. We use this value, with estimates of the total extension from the early Carboniferous to Present, to determine a likely minimum value for the mid-Mid-Jurassic through mid-Cretaceous extension. After justifying the use of Airy isostasy for the loading response of the lithosphere we show that the observed unloaded basement subsidence history is compatible with the parameters we derive for the pre and post Mid-Jurassic extension. Our minimum estimate of 38 km is still significantly higher than that: made by summing the heave on the faults active throughout the Upper Jurassic and lower Cretaceous.     

Controls on early post-rift physiography and stratigraphy, lower to mid-Cretaceous, North Viking Graben, Norwegian North Sea

The transition from syn- to post-rift is often poorly constrained and in contrast to syn-rift systems, the controls on the development of post-rift systems are poorly understood. This paper documents the timing of the post-rift onset and discusses the controls that affected the subsequent development of the post-rift infill of the North Viking Graben using an integration of seismic and well data. The study enhances our understanding of post-rift system development in general and provides an analogue for other post-rift systems. Within the early post-rift infill of the North Viking Graben five key seismic surfaces were mapped [Base Cretaceous Unconformity (BCU), Intra-Aptian, Top Albian, Top Cenomanian and Top Turonian], which divide the post-rift interval into four key seismic stratigraphic units (K1–K4). The BCU has an intra-Volgian age on the basin slopes and shelfal and terrace areas and is interpreted to mark the end of rifting in the study area. On the footwall crests adjacent to the graben the BCU represents a complex unconformity from the syn- and post-rift combined, and in the graben it forms a conformable contact. Therefore, the BCU could not be used to date the onset of the post-rift in these locations. The thickness variations and age relationships between the syn-rift stratigraphy and the K-units reveal that the early post-rift infill of the North Viking Graben was dominantly controlled by the significant local syn-rift topography, especially in the K1 and K2 stages. The Cretaceous post-rift stratigraphy was also influenced by relative base level, which controlled the sediment source areas, the development of the basin geometry itself and subsequently the style of sediment deposition in the study area. Regional variations are also recognised in the post-rift stratigraphy although these variances are strongly influenced by the local basin physiography.     

The structural and sedimentological evolution of early synrift successions: the Middle Jurassic Tarbert Formation, North Sea

ABSTRACT This study addresses the complex relationship between an evolving fault population and patterns of synrift sedimentation during the earliest stages of extension. We have used 3D seismic and well data to examine the early synrift Tarbert Formation from the Middle–Late Jurassic northern North Sea rift basin. The Tarbert Formation is of variable thickness across the study area, and thickness variations define a number of 1- to 5-km-wide depocentres bounded by normal faults. Seismic reflections diverge towards the bounding faults indicating that the faults were active contemporaneous with the deposition of the formation. Many of these faults became inactive during later Heather Formation times. The preservation of the Tarbert Formation in both footwall and hangingwall locations demonstrates that, during the earliest synrift, the rate of deposition balanced the rate of tectonic subsidence. Local space generated by hangingwall subsidence was superimposed upon accommodation generated due to a regional rise in relative sea-level. In basal Tarbert Formation times, transgression across the prerift coastal plain produced lagoons and bays, which became increasingly marine. During continued transgression, barrier islands moved landward across the drowned bays. In the southern part of our study area, shallow marine sediments are erosionally truncated by fluvial deposition. These fluvial systems were constrained by fault growth monoclines, and flowed parallel to the main faults. We illustrate that stratal architecture and facies distribution of early sedimentation is strongly influenced by the active short-lived faults. Local depocentres adjacent to fault displacement maxima focused channel stacking and allowed the aggradation of thick shoreface successions. These depocentres formed early in the rift phase are not necessarily related to Late Jurassic – Early Cretaceous depocentres developed along the major linked normal fault systems.     

The episodic geomorphological-sedimentary evolution of different basins in the Fenwei Graben and its tectonic implication

There are a series of basins in the Fenwei Graben. Field survey found that there took place several paleolake regressions or intensive stream down-incisions in all basins during the Mid-Late Quaternary. The lowest and oldest paleosol/loess units overlying three of the lacustrine terraces or alluvial ones and some paleomagenetism data from the lacustrine sediment indicate that the onset times of three paleolake regressions or intensive stream down-incisions are synchronous with the formation of L₉, L₆ and L₂ respectively in the Weihe Basin, S₈, S₅ and S₁ respectively in the Linfen-Taiyuan-Xingding Basins, and L₈, L₅ and L₁ respectively in the Datong Basin. The difference in the onset time of each lake regressions or intensive stream down-incision in different basins reveals that the farther the basin is from the Tibetan Plateau, the later it took place. Taking these field facts and the former research results in terms of the regional tectonic movement into account, it is inferred that the tectonic movement of the Tibetan Plateau most probably controlled such geomorphologicalsedimentary evolution in the graben.     

Evolution of basin architecture in an incipient continental rift: the Cenozoic Most Basin, Eger Graben (Central Europe)

The Oligo-Miocene Most Basin is the largest preserved sedimentary basin within the Eger Graben, the easternmost part of the European Cenozoic Rift System (ECRIS). The basin is interpreted as a part of an incipient rift system that underwent two distinct phases of extension. The first phase, characterised by NNE–SSW- to N–S-oriented horizontal extension between the end of Eocene and early Miocene, was oblique to the rift axis and caused evolution of a fault system characterised by en-échelon-arranged E–W (ENE–WSW) faults. These faults defined a number of small, shallow initial depocentres of very small subsidence rates that gradually merged during the growth and linkage of the normal fault segments. The youngest part of the basin fill indicates accelerated subsidence caused probably by the concentration of displacement at several major bounding faults. Major post-depositional faulting and forced folding were related to a change in the extension vector to an orthogonal position with respect to the rift axis and overprinting of the E–W faults by an NE–SW normal fault system. The origin of the palaeostress field of the earlier, oblique, extensional phase remains controversial and can be attributed either to the effects of the Alpine lithospheric root or (perhaps more likely because of the dominant volcanism at the onset of Eger Graben formation) to doming due to thermal perturbation of the lithosphere. The later, orthogonal, extensional phase is explained by stretching along the crest of a growing regional-scale anticlinal feature, which supports the recent hypothesis of lithospheric folding in the Alpine–Carpathian foreland.     

Mid-Jurassic through mid-Cretaceous extension in the Central Graben of the North Sea - part 2: estimates from faulting observed on a seismic reflection line

Abstract We present an interpretation of the structure and faulting of an industry multichannel line across the Central North Sea Graben. We observe substantial faulting between the mid-Jurassic and mid-Cretaceous and on the base Zechstein (salt) reflector. To estimate the extension from these faults we consider movement along both planar and curved faults. We demonstrate that summing the heave (the horizontal displacement) overestimates the time measure of elongation for planar, ‘domino-type’, faulting. However, for high-angle normal faults and up to 70% extension (β= 1.7) the heave only overestimates the extension by 13%. In the absence of other information, summing the heave provides a useful estimate of extension in the case of domino-type faulting. For curved ‘listric’ faults the heave is only a true measure of the elongation if the antithetic faulting which removes the voids is vertical. Antithetic movement along inclined shear planes implies significantly more extension. We used the two models; of faulting to introduce progressively greater amounts of internal deformation in the crustal rocks and sediments to attempt to reconcile the estimate of extension necessary to give the observed subsidence and that given by analysing the faults visible on the seismic line. Estimates of extension obtained by allowing antithetic faulting along inclined shear planes are consistent with the range of estimates necessary to account for the post-mid-Jurassic subsidence. The estimates for the prior mid-Jurassic faulting are still substantially less than those necessary to explain the subsidence. However, this is not of major concern as there are many reasons as to why analysis of the faulting should underestimate the pre mid-Jurassic extension. Our interpretation of the seismic line implies curved faults bottoming in the lithologically weak Zechstein salt. These faults are decoupled from the region below and, hence, do not reflect the geometry of the faulting in the basement.     

A proposed granite batholith along the western flank of the North Sea Viking Graben

Summary. A pronounced positive magnetic anomaly of approximately 300 gamma occurs over the eastern edge of the East Shetland Platform at approximately 60°N, 1°E. After the removal of the regional gravity variation and the gravity effect of the known geological structure, it is found that this magnetic high correlates with a negative gravity residual anomaly of approximately 30 mGal. Seismic data indicate that these anomalies occur in an area of relatively shallow basement on the upthrown side of the main Viking Graben margin fault. The presence of a buried granite batholith of approximately 40 × 40km may explain the gravity, magnetic and seismic observations. The observed deviation of the fault defining the edge of the Viking Graben in the proximity of the proposed granite may be explained in terms of the tectonic influence of the buoyant granite block during the taphrogenic development of the graben.     

Normal fault array evolution above a reactivated rift fabric; a subsurface example from the northern Horda Platform,Norwegian North Sea

The impact of a pre‐existing rift fabric on normal fault array evolution during a subsequent phase of lithospheric extension is investigated using 2‐D and 3‐D seismic reflection, and borehole data from the northern Horda Platform, Norwegian North Sea. Two fault populations are developed: (i) a population comprising relatively tall (>2 km), N‐S‐striking faults, which have >1.5 km of throw. These faults are up to 60 km long, penetrate down into crystalline basement and bound the eastern margins of 6–15 km wide half‐graben, which contain >3 km of pre‐Jurassic, likely Permo–Triassic, but possibly Devonian syn‐rift strata; and (ii) a population comprising vertically restricted (<1 km), NW‐SE‐striking faults, which are more closely spaced (0.5–5 km), have lower displacements (30–100 m) and not as long (2–10 km) as those in the N–S‐striking population. The NW‐SE‐striking population typically occurs between the N‐S‐striking population, and may terminate against or cross‐cut the larger structures. NW–SE‐striking faults do not bound pre‐Jurassic half‐graben and are largely restricted to the Jurassic‐to‐Cretaceous succession. Seismic‐stratigraphic observations, and the stratigraphic position of the fault tips in both fault populations, allow us to reconstruct the Late Jurassic‐to‐Early Cretaceous growth history of the northern Horda Platform fault array. We suggest the large, N‐S‐striking population was active during the Permo–Triassic and possibly earlier (Devonian?), before becoming inactive and buried during the Early and Middle Jurassic. After a period of relative tectonic quiescence, the N‐S‐striking, pre‐Jurassic fault population propagated through the Early‐Middle Jurassic cover and individual fault systems rapidly (within <10 Ma) established their maximum length in response to Late Jurassic extension. These fault systems became the dominant structures in the newly formed fault array and defined the locations of the main, Late Jurassic‐to‐Early Cretaceous, syn‐rift depocentres. Late Jurassic extension was also accommodated by broadly synchronous growth of the NW‐SE‐striking fault population; the eventual death of this population occurred in response to the localization of strain onto the N–S‐striking fault population. Our study demonstrates that the inheritance of a pre‐existing rift fabric can influence the geometry and growth of individual fault systems and the fault array as a whole. On the basis of observations made in this study, we present a conceptual model that highlights the influence of a pre‐existing rift fabric on fault array evolution in polyphase rifts.     

Tectonic evolution of the North Sea basin: crustal stretching and subsidence

Summary. The lithospheric stretching model for the formation of sedimentary basins was tested in the central North Sea by a combined study of crustal thinning and basement subsidence patterns. A profile of crustal structure was obtained by shooting a long-range seismic experiment across the Central Graben, the main axis of subsidence. A seabed array of 12 seismometers in the graben was used to record shots fired in a line 530 km long across the basin. The data collected during the experiment were interpreted by modelling synthetic seismograms from a laterally varying structure, and the final model showed substantial crustal thinning beneath the graben. Subsidence data from 19 exploration wells were analysed to obtain subsidence patterns in the central North Sea since Jurassic times. Changes in water depth were quantified using foraminiferal assemblages where possible, and observed basement subsidence paths were corrected for sediment loading, compaction and changes in water depth through time. The seismic model is shown to be compatible with the observed gravity field, and the small size of observed gravity anomalies is used to argue that the basin is in local isostatic equilibrium. Both crustal thinning and basement subsidence studies indicate about 70 km of stretching across the Central Graben during the mid-Jurassic to early Cretaceous extensional event. This extension appears to have occurred over crust already slightly thinned beneath the graben, and the seismic data suggest that total extension since the early Permian may have been more than 100km. The data presented here may all be explained using a simple model of uniform extension of the lithosphere.     

Tectonic control on sedimentary evolution of three North Atlantic borderland Mesozoic basins1

Multiple episodes of extensional tectonism dominated the formation of Mesozoic fault-bounded basins on the Grand Banks of Newfoundland, the Irish Continental Shelf and the central North Sea. A range of structural and stratigraphic responses in the Jeanne d'Arc, Porcupine and Moray Firth basins support widespread synchronous tectonic controls on sedimentation during one of these episodes, the Late Cimmerian. Rifting was preceded by a phase of related tectonism during which subsidence rates began to vary across broad areas but without significant fault block rotation. This Late Cimmerian ‘onset warp’ pattern of subsidence is considered to have been essential in the establishment of restricted anoxic basins from latest Oxfordian through Kimmeridgian (sensu gallico) time and the development of one prolific layer of organic-rich source rocks. The most prominent and widely recognized structural/lithostratigraphic response to Late Cimmerian rifting was the deposition of sediment wedges. Tithonian to early Valanginian strata generally thicken- into northerly trending faults in the Jeanne d'Arc and Porcupine basins, indicating that extensional stress was orientated WNW-ESE across a very broad area. The misalignment of this regional Late Cimmerian extensional stress with local inherited structural fabric may be responsible for transpressional uplift of individual fault blocks in the Outer Moray Firth basin. Sedimentological responses to Late Cimmerian rifting were varied, though a common lithofacies stacking pattern is recognized. Variably thick conglomerates and/or sandstones were widely deposited at the start of rift deformation, while palaeoenvironments ranged from alluvial and braid plain to submarine fan even within individual basins. The relatively coarse basal sediments fine upwards into a second layer of commonly organic-rich shales and mark The widest variations in palaeoenvironments and sediment thicknesses occurred during the last phase of Late Cimmerian rift tectonism, though all three basins show evidence of decreasing water depths, increasing oxygen levels and increasing grain size. This lithofacies stacking pattern of relatively coarse to fine to coarse (reservoir/source/reservoir) and the development of bounding unconformities are largely attributable to progressive changes in rift-controlled subsidence. Rift basin subsidence rates are interpreted to increase from a low at initiation of faulting to a mid-rift peak, followed by slowing subsidence to the end of extension. A number of counteracting crustal mechanisms that may account for progressive variations in rift-induced subsidence are considered.     

Tectono‐sedimentary evolution of the western Corinth rift (Central Greece)

The Corinth rift (Greece) is one of the world's most active rifts. The early Plio‐Pleistocene rift is preserved in the northern Peloponnese peninsula, south of the active Corinth rift. Although chronostratigraphic resolution is limited, new structural, stratigraphic and sedimentological data for an area >400 km² record early rift evolution in three phases separated by distinct episodes of extension rate acceleration and northward fault migration associated with major erosion. Minimum total N–S extension is estimated at 6.4–7.7 km. The earliest asymmetrical, broad rift accommodated slow extension (0.6–1 mm a^?1) over >3 Myrs and closed to the west. North‐dipping faults with throws of 1000–2200 m defined narrow blocks (4–7 km) with little footwall relief. A N‐NE flowing antecedent river system infilled significant inherited relief (Lower group). In the earliest Pleistocene, significant fluvial incision coincided with a 15 km northward rift margin migration. Extension rates increased to 2–2.5 mm a^?1. The antecedent rivers then built giant Gilbert‐type fan deltas (Middle group) north into a deepening lacustrine/marine basin. N‐dipping, basin margin faults accommodated throws <1500 m. Delta architecture records initiation, growth and death of this fault system over ca. 800 ka. In the Middle Pleistocene, the rift margin again migrated 5 km north. Extension rate increased to 3.4–4.8 mm a^?1. This transition may correspond to an unconformity in offshore lithostratigraphy. Middle group deltas were uplifted and incised as new hangingwall deltas built into the Gulf (Upper group). A final increase to present‐day extension rates (11–16 mm a^?1) probably occurred in the Holocene. Fault and fault block dimensions did not change significantly with time suggesting control by crustal rheological layering. Extension rate acceleration may be due to strain softening or to regional tectonic factors.