Tectono-sedimentary processes along an active marine/lacustrine half-graben margin: Alkyonides Gulf, E. Gulf of Corinth, Greece

ABSTRACT The Alkyonides half‐graben is separated from the Gerania Range to the south by active faults whose offshore traces are mapped in detail. The East Alkyonides and Psatha Faults have well‐defined, Holocene‐active tip zones and cannot be extrapolated from the onshore Skinos Fault into a single continuous surface trace. During the late Quaternary, catchments draining the step‐faulted range front have supplied sediment to alluvial fans along a subsiding marine ramp margin in the hangingwall of the Skinos Fault, to shelf ledge fans on the uplifting footwall to the East Alkyonides Fault and to the Alepochori submarine fan in the hangingwall of the latter. During late Pleistocene lowstand times (c. 70–12 ka), sediment was deposited in Lake Corinth as fan deltas on the subsiding Skinos shelf ramp which acted as a sediment trap for the adjacent 360 m deep submarine basin plain. At the same time, the uplifting eastern shelf ledge was exposed, eroded and bypassed in favour of deposition on the Alepochori submarine fan. During Holocene times, the Skinos bajada was first the site of stability and soil formation, and then of substantial deposition before modern marine erosion cut a prominent cliffline. The uplifting eastern shelf ledge has developed substantial Holocene fan lobe depositional sequences as sediment‐laden underflows have traversed it via outlet channels. We estimate mean Holocene displacement rates towards the tip of the Psatha Fault in the range 0.7–0.8 mm year^?1. Raised Holocene coastal notches indicate that this may be further partitioned into about 0.2 mm year^?1 of footwall uplift and hence 0.5–0.6 mm year^?1 of hangingwall subsidence. Holocene displacement rates towards the tip of the active East Alkyonides Fault are in the range 0.2–0.3 mm year^?1. Any uplift of the West Alkyonides Fault footwall is not keeping pace with subsidence of the Skinos Fault hangingwall, as revealed by lowstand shelf fan deltas which show internal clinoforms indicative of aggradational deposition in response to relative base‐level rise due to active hangingwall subsidence along the Skinos Fault. Total subsidence here during the last 58 kyr lowstand interval of Lake Corinth was some 20 m, indicating a reduced net displacement rate compared to estimates of late Holocene (< 2000 bp ) activity from onshore palaeoseismology. This discrepancy may be due to the competition between uplift on the West Alkyonides Fault and subsidence on the onshore Skinos Fault, or may reflect unsteady rates of Skinos Fault displacement over tens of thousands of years.     

Evolution of a mixed siliciclastic‐carbonate deep‐marine system on an unstable margin: The Cretaceous of the Eastern Greater Caucasus,Azerbaijan

Mixed siliciclastic‐carbonate deep‐marine systems (mixed systems) are less documented in the geological record than pure siliciclastic systems. The similarities and differences between these systems are, therefore, poorly understood. A well‐exposed Late Cretaceous mixed system on the northern side of the Eastern Greater Caucasus, Azerbaijan, provides an opportunity to study the interaction between contemporaneous siliciclastic and carbonate deep‐marine deposition. Facies analysis reveals a Cenomanian–early Turonian siliciclastic submarine channel complex that abruptly transitions into a Mid Turonian–Maastrichtian mixed lobe‐dominated succession. The channels are entrenched in lows on the palaeo‐seafloor but are absent 10 km towards the west where an Early Cretaceous submarine landslide complex acted as a topographic barrier to deposition. By the Campanian, this topography was largely healed allowing extensive deposition of the mixed lobe‐dominated succession. Evidence for irregular bathymetry is recorded by opposing palaeoflow indicators and frequent submarine landslides. The overall sequence is interpreted to represent the abrupt transition from Cenomanian–early Turonian siliciclastic progradation to c. Mid Turonian retrogradation, followed by a gradual return to progradation in the Santonian–Maastrichtian. The siliciclastic systems periodically punctuate a more widely extensive calcareous system from the Mid Turonian onwards, resulting in a mixed deep‐marine system. Mixed lobes differ from their siliciclastic counterparts in that they contain both siliciclastic and calcareous depositional elements making determining distal and proximal environments challenging using conventional terminology and complicate palaeogeographic interpretations. Modulation and remobilisation also occur between the two contemporaneous systems making stacking patterns difficult to decipher. The results provide insight into the behaviour of multiple contemporaneous deep‐marine fans, an aspect that is challenging to decipher in non‐mixed systems. The study area is comparable in terms of facies, architectures and the presence of widespread instability to offshore The Gambia, NW Africa, and could form a suitable analogue for mixed deep‐marine systems observed elsewhere.     

The tectono‐sedimentary evolution of a supra‐detachment rift basin at a deep‐water magma‐poor rifted margin: the example of the Samedan Basin preserved in the Err nappe in SE Switzerland

We describe the tectono‐sedimentary evolution of a Middle Jurassic, rift‐related supra‐detachment basin of the ancient Alpine Tethys margin exposed in the Central Alps (SE Switzerland). Based on pre‐Alpine restoration, we demonstrate that the rift basin developed over a detachment system that is traced over more than 40 km from thinned continental crust to exhumed mantle. The detachment faults are overlain by extensional allochthons consisting of upper crustal rocks and pre‐rift sediments up to several kilometres long and several hundreds of metres thick, compartmentalizing the distal margin into sub‐basins. We mapped and restored one of these sub‐basins, the Samedan Basin. It consists of a V‐shape geometry in map view, which is confined by extensional allochthons and floored by a detachment fault. It can be restored over a minimum distance of 11 km along and about 4 km perpendicular to the basin axis. Its sedimentary infill can be subdivided into basal (initial), intermediate (widening) and top (post‐tectonic) facies tracts. These tracts document (1) formation of the basin initially bounded by high‐angle faults and developing into low‐angle detachment faults, (2) widening of the basin and (3) migration of deformation further outboard. The basal facies tract is made of locally derived, poorly sorted gravity flow deposits that show a progressive change from hangingwall to footwall‐derived lithologies. Upsection the sediments develop into turbidity current deposits that show retrogradation (intermediate facies tract) and starvation of the sedimentary system (post‐tectonic facies tract). On the scale of the distal margin, the syn‐tectonic record documents a thinning‐ and fining‐upward sequence related to the back stepping of the tectonically derived sediment source, progressive starvation of the sedimentary system and migration of deformation resulting in exhumation and progressive delamination of the thinned crust during final rifting. This study provides valuable insights into the tectono‐sedimentary evolution and stratigraphic architecture of a supra‐detachment basin formed over hyper‐extended crust.     

Relationships between morphological and sedimentological parameters in source‐to‐sink systems: a basis for predicting semi‐quantitative characteristics in subsurface systems

The study of source‐to‐sink systems relates long‐term variations in sediment flux to morphogenic evolution of erosional–depositional systems. These variations are caused by an intricate combination of autogenic and allogenic forcing mechanisms that operate on multiple time scales – from individual transport events to large‐scale filling of basins. In order to achieve a better understanding of how these mechanisms influence morphological characteristics on different scales, 29 submodern source‐to‐sink systems have been investigated. The study is based on measurements of morphological parameters from catchments, shelves and slopes derived from a ∼1 km global digital elevation model dataset, in combination with data on basin floor fans, sediment supply, water discharge and deposition rates derived from published literature. By comparing various morphological and sedimentological parameters within and between individual systems, a number of relationships governing system evolution and behaviour are identified. The results suggest that the amount of low‐gradient floodplain area and river channel gradient are good indicators for catchment storage potential. Catchment area and river channel length is also related to shelf area and shelf width, respectively. Similarly to the floodplain area, these parameters are important for long‐term storage of sediment on the shelf platform. Additionally, the basin floor fan area is correlative to the long‐term deposition rate and the slope length. The slope length thus proves to be a useful parameter linking proximal and distal segments in source‐to‐sink systems. The relationships observed in this study provide insight into segment scale development of source‐to‐sink systems, and an understanding of these relationships in modern systems may result in improved knowledge on internal and external development of source‐to‐sink systems over geological time scales. They also allow for the development of a set of semi‐quantitative guidelines that can be used to predict similar relationships in other systems where data from individual system segments are missing or lacking.     

Forward stratigraphic modelling of sediment pathways and depocentres in salt‐influenced passive‐margin basins: Lower Cretaceous,central Scotian Basin

Source‐to‐sink studies and numerical modelling software are increasingly used to better understand sedimentary basins, and to predict sediment distributions. However, predictive modelling remains problematic in basins dominated by salt tectonics. The Lower Cretaceous delta system of the Scotian Basin is well suited for source‐to‐sink studies and provides an opportunity to apply this approach to a region experiencing active salt tectonism. This study uses forward stratigraphic modelling software and statistical analysis software to produce predictive stratigraphic models of the central Scotian Basin, test their sensitivity to different input parameters, assess proposed provenance pathways, and determine the distribution of sand and factors that control sedimentation in the basin. Models have been calibrated against reference wells and seismic surfaces, and implement a multidisciplinary approach to define simulation parameters. Simulation results show that previously proposed provenance pathways for the Early Cretaceous can be used to generate predictive stratigraphic models, which simulate the overall sediment distribution for the central Scotian Basin. Modelling confirms that the shaly nature of the Naskapi Member is the result of tectonic diversion of the Sable and Banquereau rivers and suggests additional episodic diversion during the deposition of the Cree Member. Sand is dominantly trapped on the shelf in all units, with transport into the basin along salt corridors and as a result of turbidity current flows occurring in the Upper Missisauga Formation and Cree Member. This led to sand accumulation in minibasins with a large deposit seawards of the Tantallon M‐41 well. Sand also appears to bypass the basin via salt corridors which lead to the down‐slope edge of the study area. Sensitivity analysis suggests that the grain size of source sediments to the system is the controlling factor of sand distribution. The methodology applied to this basin has applications to other regions complicated by salt tectonics, and where sediment distribution and transport from source‐to‐sink remain unclear.     

Present‐day stresses in Brunei,NW Borneo: superposition of deltaic and active margin tectonics

The Baram Delta System, Brunei, NW Borneo, is a Tertiary delta system located on an active continental margin. Delta top regions in many Tertiary delta systems (e.g. Niger Delta) are thought to exhibit a normal‐fault stress regime and margin‐parallel maximum horizontal stress orientations. However, unlike in passive margin Tertiary delta systems, two present‐day stress provinces have been previously identified across the Baram Delta System: an inner shelf inverted province with a margin‐normal (NW–SE) maximum horizontal stress orientation and an outer shelf extension province with a margin‐parallel (NE–SW) maximum horizontal stress orientation. Before this study, there were few data constraining the inverted province other than in the vicinity of the Champion Fields. New data from 12 petroleum wells in the western inner shelf and onshore west Brunei presented herein confirm the margin‐normal maximum horizontal stress orientations of the inverted province. A total of 117 borehole breakouts, all documented in shale units, and one drilling‐induced tensile fracture (in a sandstone interval) reveal a mean maximum horizontal stress orientation of 117 with a standard deviation of 19°. This orientation is consistent with contemporary margin‐normal maximum horizontal stress orientations of the inverted province described previously in the vicinity of the Champion Fields that have been linked to basement tectonics of the Crocker–Rajang accretionary complex and associated active margin. However, stress magnitudes calculated using data from these 12 petroleum wells indicate a borderline strike–slip fault to normal fault stress regime for the present day; combined with the absence of seismicity, this suggests that the studied part of the NW Borneo continental margin is currently tectonically quiescent.     

Tectonic and sedimentological evolution of the Pliocene–Quaternary basins of Zakynthos island, Greece: case study of the transition from compressional to extensional tectonics

Pliocene–Quaternary basins of the Ionian islands evolved in a complex tectonic setting that evolved from a mid to late Cenozoic compressional zone of the northern external Hellenides to the rapidly extending Pliocene–Quaternary basins of the Peloponnese. The northern limit of the Hellenic Trench marks the junction of these two tectonic regimes. A foreland-propagating fold and thrust system in the northern external Hellenides segmented the former Miocene continental margin basin in Zakynthos and permitted diapiric intrusion of Triassic gypsum along thrust ramps. Further inboard, coeval extensional basins developed, with increasing rates of subsidence from the Pliocene to Quaternary, resulting in four principal types of sedimentation: (1) condensed shelf-sedimentation on the flanks of rising anticlines; (2) coarse-grained sedimentation in restricted basins adjacent to evaporitic diapirs rising along thrust ramps; (3) larger basins between fold zones were filled by extrabasinal, prodeltaic mud and sand from the proto-Acheloos river; (4) margins of subsiding Quaternary basins were supplied at sea-level highstands by distal deltaic muds and at lowstands by locally derived coarse clastic sediment.     

Sediment dispersal and redistributive processes in axial and transverse deep‐time source‐to‐sink systems of marine rift basins: Dampier Sub‐basin,Northwest Shelf,Australia

Morphological scaling relationships between source‐to‐sink segments have been widely explored in modern settings, however, deep‐time systems remain difficult to assess due to limited preservation of drainage basins and difficulty in quantifying complex processes that impact sediment dispersals. Integration of core, well‐logs and 3‐D seismic data across the Dampier Sub‐basin, Northwest Shelf of Australia, enables a complete deep‐time source‐to‐sink study from the footwall (Rankin Platform) catchment to the hanging wall (Kendrew Trough) depositional systems in a Jurassic late syn‐rift succession. Hydrological analysis identifies 24 drainage basins on the J50.0 (Tithonian) erosional surface, which are delimited into six drainage domains confined by NNE‐SSW trending grabens and their horsts, with drainage domain areas ranging between 29 and 156 km². Drainage outlets of these drainage domains are well preserved along the Rankin Fault System scarp, with cross‐sectional areas ranging from 0.08 to 0.31 km². Corresponding to the six drainage domains, sedimentological and geomorphological analysis identifies six transverse submarine fan complexes developing in the Kendrew Trough, ranging in areas from 43 to 193 km². Seismic geomorphological analysis reveals over 90‐km‐long, slightly sinuous axial turbidity channels, developing in the lower topography of the Kendrew Trough which erodes toe parts of transverse submarine fan complexes. Positive scaling relationships exist between drainage outlet spacing and drainage basin length, and drainage outlet cross‐sectional area and drainage basin area, which indicates the geometry of drainage outlets can provide important constraints on source area dimensions in deep‐time source‐to‐sink studies. The broadly negative bias of fan area to drainage basin area ratios indicates net sediment losses in submarine fan complexes caused by axial turbidity current erosion. Source‐to‐sink sediment balance studies must be done with full evaluating of adjacent source‐to‐sink systems to delineate fans and their associated up‐dip drainages, to achieve an accurate tectonic and sedimentologic picture of deep‐time basins.     

Morphology and structure of a landslide complex in an active margin setting: The Waitawhiti complex, North Island, New Zealand

Multi-scale gravitational instabilities are widespread in the Coastal Ranges of the North Island of New Zealand. We document here a detailed analysis of the Waitawhiti landslide complex, located in the core of the Tawhero syncline, and investigate the potential landslides triggering factors in the area. Four contiguous large slides form the Waitawhiti complex. These slides involve fine-grained Miocene sandstones and massive fractured siltstones. Sliding occurs mostly along nearly horizontal strata. All slides are bounded laterally and/or distally by deep-incised valleys. Three gas seeps evidencing thermogenic gas release have been discovered in the vicinity of the slides. We propose that river incision, continuously removing distal buttresses, is the main destabilizing factor in the area. However, additional factors, such as tectonic activity and intense rainfall, cannot be excluded. We also propose that fluid overpressure, reducing the effective shear strength at the base of low-permeability layers, may have influenced the triggering of landslides in the Waitawhiti area.     

Source‐to‐sink analysis in an active extensional setting: Holocene erosion and deposition in the Sperchios rift,central Greece

We present a source‐to‐sink analysis to explain sediment supply variations and depositional patterns over the Holocene within an active rift setting. We integrate a range of modelling approaches and data types with field observations from the Sperchios rift basin, Central Greece that allow us to analyse and quantify (1) the size and characteristics of sediment source areas, (2) the dynamics of the sediment routing system from upstream fluvial processes to downstream deposition at the coastline, and (3) the depositional architecture and volumes of the Holocene basin fill. We demonstrate that the Sperchios rift comprises a ‘closed’ system over the Holocene and that erosional and depositional volumes are thus balanced. Furthermore, we evaluate key controls in the development of this source‐to‐sink system, including the role of pre‐existing topography, bedrock erodibility and lateral variations in the rate of tectonic uplift/subsidence. We show that tectonic subsidence alone can explain the observed grain size fining along the rift axis resulting in the downstream transition from a braided channel to an extensive meander belt (>15 km long) that feeds the fine‐grained Sperchios delta. Additionally, we quantify the ratios of sediment storage to bypass for the two main footwall‐sourced alluvial fan systems and relate the fan characteristics to the pattern and rates of fault slip. Finally, we show that ≥40% of the sediment that builds the Sperchios delta is supplied by ≤22% of the entire source area and that this can be primarily attributed to a longer‐term (~10⁶ years) transient landscape response to fault segment linkage. Our multidisciplinary approach allows us to quantify the relative importance of multiple factors that control a complex source‐to‐sink system and thus improve our understanding of landscape evolution and stratigraphic development in active extensional tectonic settings.     

Multi‐scale constraints of sediment source to sink systems in frontier basins: a forward stratigraphic modelling case study of the Levant region

Recent scientific work has highlighted the presence of an up to 12 km thick Cenozoic siliclastic and carbonate infill in the Levant Basin. Since the Late Eocene, several regional geodynamic events affecting Afro‐Arabia and Eurasia (collision and strike slip deformation) induced marginal uplifts. The initiation of local and long‐lived regional drainage systems in the Oligo‐Miocene period (e.g., Lebanon, Arabia and Nile) provoked a change in the depositional pattern along the Levant region from carbonate‐dominated to mixed clastic‐rich systems. Herein, we explore the importance of multi‐scale constraints (i.e., seismic, well and field data) in the quantification of subsidence history, sediment transport and deposition of a Middle to Upper Miocene “multi‐source” to sink system along the northern Levant frontier region. Through a comprehensive 4D forward stratigraphic modelling workflow, we suggest that the contribution to basin infill is split between proximal and more distal clastic sources as well as in situ carbonate and hemipelagic deposition. The results show that single‐source scenarios could not reasonably satisfy the basin‐scale constraints. The worldwide application of such new multi‐disciplinary workflows in frontier regions highlights the additional data constraints that are needed to de‐risk highly uncertain geological models in the hydrocarbon exploration phase.     

Along‐strike structural linkage and interaction in an active thrust fault system: A case study from the western Sichuan foreland basin,China

Along‐strike structural linkage and interaction between faults is common in various compressional settings worldwide. Understanding the kinematic history of fault interaction processes can provide important constraints on the geometry and evolution of the lateral growth of segmented faults in the fold‐and‐thrust belts, which are important to seismic hazard assessment and hydrocarbon trap development. In this study, we study lateral structural geometry (fault displacement and horizon shortening) of thrust fault linkages and interactions along the Qiongxi anticline in the western Sichuan foreland basin, China, using a high‐resolution 3D seismic reflection dataset. Seismic interpretation suggests that the Qiongxi anticline can be related to three west‐dipping, hard‐linked thrust fault segments that sole onto a regional shallow detachment. Results reveal that the lateral linkage of fault segments limited their development, affecting the along‐strike fault displacement distributions. A deficit between shortening and displacement is observed to increase in linkage zones where complex structural processes occur, such as fault surface bifurcation and secondary faulting, demonstrating the effect of fault linkage process on structural deformation within a thrust array. The distribution of the geometrical characteristics shows that thrust fault development in the area can be described by both the isolated fault model and the coherent fault model. Our measurements show that new fault surfaces bifurcate from the main thrust ramp, which influences both strain distribution in the relay zone and along‐strike fault slip distribution. This work fully describes the geometric and kinematic characteristics of lateral thrust fault linkage, and may provide insights into seismic interpretation strategies in other complex fault transfer zones.     

Structural controls on the stratigraphic architecture of net‐transgressive shallow‐marine strata in a salt‐influenced rift basin: Middle‐to‐Upper Jurassic Egersund Basin,Norwegian North Sea

In this study, we integrate 3D seismic reflection, wireline log, biostratigraphic and core data from the Egersund Basin, Norwegian North Sea to determine the impact of syn‐depositional salt movement and associated growth faulting on the sedimentology and stratigraphic architecture of the Middle‐to‐Upper Jurassic, net‐transgressive, syn‐rift succession. Borehole data indicate that Middle‐to‐Upper Jurassic strata consist of low‐energy, wave‐dominated offshore and shoreface deposits and coal‐bearing coastal‐plain deposits. These deposits are arranged in four parasequences that are aggradationally to retrogradationally stacked to form a net‐transgressive succession that is up to 150‐m thick, at least 20 km in depositional strike (SW‐NE) extent, and >70 km in depositional dip (NW‐SE) extent. In this rift‐margin location, changes in thickness but not facies are noted across active salt structures. Abrupt facies changes, from shoreface sandstones to offshore mudstones, only occur across large displacement, basement‐involved normal faults. Comparisons to other tectonically active salt‐influenced basins suggest that facies changes across syn‐depositional salt structures are observed only where expansion indices are >2. Subsidence between salt walls resulted in local preservation of coastal‐plain deposits that cap shoreface parasequences, which were locally removed by transgressive erosion in adjacent areas of lower subsidence. The depositional dip that characterizes the Egersund Basin is unusual and likely resulted from its marginal location within the evolving North Sea rift and an extra‐basinal sediment supply from the Norwegian mainland.     

Tectonic development of the Drummond Basin, eastern Australia: backarc extension and inversion in a Late Palaeozoic active margin setting

Detailed seismic reflection data combined with regional magnetic, gravity and geological data indicate that the Drummond Basin originated as a backare extensional basin associated with Late Devonian and Early Carboniferous active margin tectonism in the northern New England Fold Belt. Seismic reflection data have been used to generate a two-way time map of seismic basement, providing a clear view of the basinal geometry and structural development. Broadscale structural asymmetry of the basin implies that simple shear along a deep, upper-crustal detachment provided the extensional mechanism and generated an inter-related set of listric normal faults and associated transfer faults, as well as steeply-dipping planat normal faults. The orientation of normal faults near the basin margins appears to have been controlled by regional basement structural trends. Transfer-fault trends were approximarely orthogonal to the line of plate convergence as assessed from the orientation of coeval are, forcare and subduction complex stratorectonic elements. Three distinct phases of infill are represented in the basinal stratigraphic succession. The first consists largely of volcanics and volcaniclastics, indicating that effusive magmatism and extension were closely associated in space and time. The second is quartzose and of basement derivation, but was not derived from footwall blocks at the faulted basinal margins to the east and north. Uplifted hanging-wall crust beyond the western basinal margin, a product of west-directed simple shear detachment, was the likely source terrain. The final infill phase consisted of volcaniclastics considered to have been derived from a coeval volcanic are to the east. Major faults at the basin margins provided conduits for magmatism during extensional basin development, and long after the basinal history was complete. During the Late Carboniferous and mid-Triassic, the basin was affected by two discrete episodes of compressional deformation. This led to inversion with the development of folds, and reverse and wrench faults now seen at the surface.     

Anomalous passive subsidence of deep‐water sedimentary basins: a prearc basin example,southern New Caledonia Trough and Taranaki Basin,New Zealand

Stratigraphic data from petroleum wells and seismic reflection analysis reveal two distinct episodes of subsidence in the southern New Caledonia Trough and deep‐water Taranaki Basin. Tectonic subsidence of ~2.5 km was related to Cretaceous rift faulting and post‐rift thermal subsidence, and ~1.5 km of anomalous passive tectonic subsidence occurred during Cenozoic time. Pure‐shear stretching by factors of up to 2 is estimated for the first phase of subsidence from the exponential decay of post‐rift subsidence. The second subsidence event occured ~40 Ma after rifting ceased, and was not associated with faulting in the upper crust. Eocene subsidence patterns indicate northward tilting of the basin, followed by rapid regional subsidence during the Oligocene and Early Miocene. The resulting basin is 300–500 km wide and over 2000 km long, includes part of Taranaki Basin, and is not easily explained by any classic model of lithosphere deformation or cooling. The spatial scale of the basin, paucity of Cenozoic crustal faulting, and magnitudes of subsidence suggest a regional process that acted from below, probably originating within the upper mantle. This process was likely associated with inception of nearby Australia‐Pacific plate convergence, which ultimately formed the Tonga‐Kermadec subduction zone. Our study demonstrates that shallow‐water environments persisted for longer and their associated sedimentary sequences are hence thicker than would be predicted by any rift basin model that produces such large values of subsidence and an equivalent water depth. We suggest that convective processes within the upper mantle can influence the sedimentary facies distribution and thermal architecture of deep‐water basins, and that not all deep‐water basins are simply the evolved products of the same processes that produce shallow‐water sedimentary basins. This may be particularly true during the inception of subduction zones, and we suggest the term ‘prearc’ basin to describe this tectonic setting.     

Constraining recycled detritus in quartz‐rich sandstones: Insights from a multi‐proxy provenance study of the Mid‐Carboniferous,Clare Basin,western Ireland

Quartz‐rich sandstones can be produced through multiple sedimentary processes, potentially acting in combination, such as extensive sedimentary recycling or intense chemical weathering. Determining the provenance of such sedimentary rocks can be challenging due to low amounts of accessory minerals, the fact that the primary mineralogy may have been altered during transport, storage or burial and difficulties in the recognition of polycyclic components. This study uses zircon and apatite U‐Pb geochronology, apatite trace elements, zircon‐tourmaline‐rutile indices and petrographic observations to investigate the sedimentary history of mineralogically mature mid‐Carboniferous sandstones of the Tullig Cyclothem, Clare Basin, western Ireland. The provenance data show that the sandstones have been dominantly and ultimately sourced from three basement terranes: older Laurentian‐ associated rocks (ca. 900–2500 Ma) which lay to the north of the basin, peri‐Gondwanan terranes (ca. 500–700 Ma) to the south and igneous intrusive rocks associated with the Caledonian Orogenic Cycle (ca. 380–500 Ma). However, the multi‐proxy approach also helps constrain the sedimentary history and suggests that not all grain populations were derived directly from their original source. Grains with a Laurentian or a Caledonian affinity have likely been recycled through Devonian basins to the south. Grains with a peri‐Gondwanan affinity appear to be first cycle and are potentially derived from south/southwest of the basin. Taken as a whole, these data are consistent with input into the basin from the south and southwest, with the reworking of older sedimentary rocks, rather than intensive first‐cycle chemical weathering, likely explaining the compositional maturity of the sandstones. This study highlights the need for a multi‐proxy provenance approach to constrain sedimentary recycling, particularly in compositionally mature sandstones, as the use of zircon geochronology alone would have led to erroneous provenance interpretations. Zircon, together with U‐Pb geochronology from more labile phases such as apatite, can help distinguish first‐cycle versus polycyclic detritus.