建筑楼梯在2008年汶川大地震中的震害分析

2008年汶川大地震中,不l同结构类型建筑的楼梯发生了不同程度的破坏,其中框架结构的楼梯破坏最严重.文中分析了砌体结构、框架结构、框剪结构的楼梯破坏原因.表明楼梯实际上参与了主体结构抗震,在整体结构中起着斜撑的作用,为限制结构层间位移作出了贡献,与目前的结构分析软件不考虑楼梯参与主体抗震作用,仅将其作为荷载加到主体结构...     

Experimental and parametric investigation of effects of built-in staircases on the dynamics of RC buildings

Past earthquakes, in many instances, have demonstrated poor performance of commonly used built-in staircase configurations. Codal provisions in India pertaining to staircases present a rather simple approach wherein the effects of built-in staircases on the overall dynamic properties or on the local behavior of structures are not addressed explicitly. Studies in the past have highlighted the scale of such effects, but most of them have relied completely on analytical models of buildings. This study analyzes the adequacy of the codal provisions by investigating two finite element (FE) models calibrated using ambient and forced vibration measurements. The effects of variations in building height, layout of staircase in plan, and presence of masonry infill walls in stairwells are also examined. The codal guidelines regarding empirical estimation of period and provision of enclosure walls around built-in staircases are found to be adequate. However, for the case of built-in staircases without enclosure walls, the force and displacement demands on landing beams are found to be considerably high. Drift-based approaches to estimate these demands are proposed.     

填充墙RC框架结构加固方法的研究现状及展望

综述了用于提高填充墙钢筋混凝土(RC)框架结构抗震性能和改善结构损伤模式的几类加固措施,从工艺、加固效果和破坏形式3个角度进行了分析.在建筑结构设计过程中,填充墙通常被视为一种典型的脆性非均质非结构构件,忽视了填充墙与RC框架之间的相互作用.地震调查报告表明,在结构遭受地震作用时,填充墙通常先于钢筋混凝土框架发生破坏,...     

钢筋混凝土框架柱震损程度量化鉴定方法

钢筋混凝土结构震后损伤鉴定中,最常见的方式是鉴定者观察房屋破坏现象,根据经验给出震损等级。该方法直观高效,但对鉴定者的专业经验要求较高,且鉴定结果的主观差异较大。对此以RC框架柱为对象,开展了基于震损现象的震损量化鉴定方法研究:在RC框架柱震损现象量化试验基础上给出基于构件骨架曲线特征阶段的震损分级方法;对7个RC框架柱试件进行了改进Park-Ang损伤指数分析,建立了RC框架柱损伤指数-震损分级-震损现象的对应关系;基于RC框架柱的试验结果及典型震害编制了RC框架柱震损图集,并给出了使用图集进行框架柱震损鉴定的流程及方法。使用该方法对2个实际震害中的RC框架柱进行了震损鉴定,可为更加客观以及准确地开展钢筋混凝土结构的震损鉴定提供参考。     

A novel structural detailing for the improvement of seismic and progressive collapse performances of RC frames

Earthquake-induced building collapse and progressive collapse due to accidental local failure of vertical components are the two most common failure modes of reinforced concrete (RC) frame structures. Conventional design methods usually focus on the design requirements of a specific hazard but neglect the interactions between different designs. For example, the progressive collapse design of an RC frame often yields increased reinforcement and flexural strength of the beams. As a result, the seismic design principle of “strong-column-weak-beam” may be violated, which may lead to unfavorable failure modes and weaken the seismic performance. To avoid these adverse effects of the progressive collapse design on the seismic resistance of RC frames, a novel structural detailing is proposed in this study. The proposed detailing technique intends to concurrently improve the seismic and progressive collapse performances of an RC frame by changing the layout of the newly added longitudinal reinforcement against progressive collapse without introducing any additional reinforcement. A six-story RC frame is used as the prototype building for this investigation. Both cyclic and progressive collapse tests are conducted to validate the performance of the proposed structural detailing. Based on the experimental results, detailed finite element (FE) models of the RC frame with different reinforcement layouts are established. The seismic and progressive collapse resistances of different models are compared based on the incremental dynamic analysis (IDA) and nonlinear dynamic alternate path (AP) methods, respectively. The results indicate that the proposed structural detailing can effectively resolve the conflict between the seismic and progressive collapse designs.     

基于有限元模拟的RC框架结构抗震性能影响因素分析

总结现行的RC框架结构抗震设计、抗震鉴定标准和震害资料,选取了场地条件、规则程度、混凝土强度以及结构层数4个影响框架结构抗震性能的主要因素进行分析;以7度设防的西南地区典型双跨外廊式教学楼为原型,设置8个分析工况,采用基于位移控制的非线性静力（Pushover）分析方法得到各工况在不同烈度罕遇地震下的最大层间位移角（ISDA）,以此为指标对4个框架结构抗震性能影响因素的重要性进行评价分析;最后采用模糊层次分析法,给出了以上影响因素在RC框架结构抗震性能评估中的重要性排序以及初始权重值。     

砌体填充墙框架结构抗震性能研究现状与展望

针对砌体填充墙框架结构在地震作用下的受力特点,分析了填充墙钢筋混凝土框架结构产生震害的主要原因。结合国内外砌体填充墙框架结构理论和试验研究成果,围绕填充墙的刚度退化规律和不同性能水平的层间位移角,评述了填充墙框架结构的研究现状。最后,结合基于性能的抗震设计理论背景和禁用黏土实心砖提倡节能的政策背景,指出了今后应以实现基于性能的抗震设计为目标,针对新型砌体填充墙框架结构开展系统研究。     

楼板及其配筋在RC框架结构实现抗震延性机制中的作用分析

总结采用梁有效翼缘来考虑楼板及配筋对"强柱弱梁"机制形成的影响的实验和数值仿真研究.基于SAP2000采用三种侧向加载模式对RC框架结构不带楼板、不带楼板考虑梁刚度放大、带楼板的三个模型进行pushover分析,对力与位移的关系曲线、塑性铰的出铰顺序以及顶点位移与层间位移等方面进行探讨.结果表明:三个模型的"强柱弱梁"...     

高强钢筋高延性纤维增强混凝土框架结构的屈服机制和抗震性能

为了对混凝土框架结构的地震破坏机制和抗震性能进行控制,在框架柱中配置高强钢筋,并将纤维增强混凝土(FRC)用于框架结构的预期损伤部位。结构柱中的高强钢筋用来减小结构的残余变形,FRC材料用来增加结构的耗能能力和损伤容限。设计了三个框架,采用动力弹塑性时程分析方法进行分析。研究结果表明,采用高强钢筋提高了结构的整体承载能力,在层间侧移角达到3%之前避免了柱铰的出现(包括底层柱底),并且减小了结构的残余变形;预期损伤部位采用FRC材料能够提高结构的塑性耗能。     

基于ETABS的钢筋混凝土框架与楼梯共同工作性能分析

本文利用大型结构分析软件ETABS设计了4种包含和不包含楼梯的钢筋混凝土框架计算模型,分别采用底部剪力法、反应谱法和时程分析法对各模型进行了弹性阶段地震反应特性对比计算分析.结果显示:楼梯参与结构整体计算后,结构出现抗侧刚度明显增加、结构扭转振动显著、梯间框架柱剪力突变等现象;建议结构设计时采用包含楼梯的层间结构计算模型(M-4),使用振型分解反应谱法进行结构抗震分析计算.     

框架-摇摆墙结构设计方法与研究现状分析

摇摆墙释放了墙底与基础之间的约束以实现竖向摇摆。已有研究表明:将摇摆墙与RC框架结构结合形成框架-摇摆墙结构体系能有效提高结构的整体承载力及延性,使结构的破坏发生在预期的位置,减少结构地震响应的不确定性。本文首先回顾了摇摆墙的发展历史,简要介绍了框架-摇摆墙结构的基本原理,综述了框架-摇摆墙结构的研究现状,总结了其墙体及连接节点的设计要点并对其未来的发展方向进行展望,指出框架-摇摆墙结构体系后续的研究重点可以包括:墙体与RC框架结构水平连接节点的设计、摇摆墙与基础实现理想铰接的设计、摇摆墙与预制装配式技术结合的设计及摇摆墙墙体在框架结构中布局方式的设计。     

Experimental investigation on reparability of an infilled rocking wall frame structure

Improving seismic performance is one of the critical objectives in earthquake engineering. With the development of economy and society, reparability and fast resilience of a structure are becoming increasingly important. Reinforced concrete (RC) frame structure is prone to soft story mechanism. As a result, deformation and damage are so concentrated that reparability is severely hampered. Rocking wall provides an available approach for deformation control in RC frame by introducing a continuous component along the height. Previous researches mostly focus on seismic responses of rocking wall frame structures, while damage mode and reparability have not been investigated in detail. In this study, a novel infilled rocking wall frame (IRWF) structure is proposed. A half‐scaled IRWF model was designed according to Chinese seismic design code. The model was subjected to cyclic pushover testing up to structure drift ratio of 1/50 (amplitude 1/50), and its reparability was evaluated thereafter. Retrofit was implemented by wrapping steel plates and installing friction dampers. The retrofitted model was further loaded up to amplitude 1/30. The IRWF model showed excellent reparability and satisfactory seismic performance on deformation control, damage mode, hysteresis behavior, and beam‐to‐column joint rotation. After retrofitting, capacity of the model was improved by 11% with limited crack distribution. The model did not degrade until amplitude 1/30, due to shear failure in frame beams. The retrofit procedure was proved effective, and reparability of the IRWF model was demonstrated. Seismic resilience tends to be achieved in the proposed system.     

An efficient performance‐based seismic design method for reinforced concrete frames

In this paper, a practical method is developed for performance‐based design of RC structures subjected to seismic excitations. More efficient design is obtained by redistributing material from strong to weak parts of a structure until a state of uniform deformation or damage prevails. By applying the design algorithm on 5, 10 and 15‐storey RC frames, the efficiency of the proposed method is initially demonstrated for specific synthetic and real seismic excitations. The results indicate that, for similar structural weight, designed structures experience up to 30% less global damage compared with code‐based design frames. The method is then developed to consider multiple performance objectives and deal with seismic design of RC structures for a design spectrum. The results show that the proposed method is very efficient at controlling performance parameters and improving structural behaviour of RC frames. Copyright © 2011 John Wiley & Sons, Ltd.     

带有可更换连梁的钢筋混凝土结构设计方法

钢筋混凝土剪力墙结构通过设置可更换连梁,在地震作用下集中损伤,保护主体结构不受或只受微小破坏,震后更换损伤构件即可恢复结构功能。参照现行规范和已有试验分析结果,在普通钢筋混凝土结构设计基础上,提出带有可更换连梁的钢筋混凝土结构实用设计方法,设定性能目标,总结设计流程。采用提出的设计方法对1个50层钢筋混凝土结构进行设计,并采用大型有限元分析软件ABAQUS建立数值模型,验证结构性能目标和提出的设计方法。结果表明:按该方法设计的带有可更换连梁的钢筋混凝土结构能满足所设定的性能目标,设计方法合理实用,为该新型结构的工程应用提供了参考。     

Seismic damage to structures in the <Emphasis Type="Italic">M</Emphasis><Subscript>s</Subscript>6.5 Ludian earthquake

On 3 August 2014, the Ludian earthquake struck northwest Yunnan Province with a surface wave magnitude of 6.5. This moderate earthquake unexpectedly caused high fatalities and great economic loss. Four strong motion stations were located in the areas with intensity V, VI, VII and IX, near the epicentre. The characteristics of the ground motion are discussed herein, including 1) ground motion was strong at a period of less than 1.4 s, which covered the natural vibration period of a large number of structures; and 2) the release energy was concentrated geographically. Based on materials collected during emergency building inspections, the damage patterns of adobe, masonry, timber frame and reinforced concrete (RC) frame structures in areas with different intensities are summarised. Earthquake damage matrices of local buildings are also given for fragility evaluation and earthquake damage prediction. It is found that the collapse ratios of RC frame and confined masonry structures based on the new design code are significantly lower than non-seismic buildings. However, the RC frame structures still failed to achieve the ‘strong column, weak beam’ design target. Traditional timber frame structures with a light infill wall showed good aseismic performance.     

强柱系数基于结构易损性的抗震性能评估

增大柱端抗弯承载力是抗震"能力设计"措施中引导钢筋混凝土框架结构形成梁铰型有利耗能机构的关键措施。本文以6层确定性钢筋混凝土框架结构为分析对象,通过结构易损性分析评估了不同强柱系数取值对钢筋混凝土框架结构抗震性能的影响。结构易损性分析表明增大柱端抗弯承载力是改善结构抗震性能的有效措施,增大强柱系数提高了结构的变形能力,使不同破坏极限状态之间形成较大的"梯度",对防止强烈地震作用下结构的突然倒塌提供了预示。结构易损性曲线对评估结构抗震性能、选用合适的目标强柱系数提供了量化标准。     

Development and modeling of a frictional wall damper and its applications in reinforced concrete frame structures

A wall‐type friction damper is newly proposed in this paper to improve the performance of reinforced concrete (RC) framed structures under earthquake loads. Traditionally, the damper was generally invented as a brace‐type member. However, it has been seen to cause problems in the RC frame structures in that concrete is apt to be damaged in the connection regions of the RC member and the brace‐type damper under earthquake loads. The proposed wall‐type damper has an advantage in the retrofit of RC structures. The system consists of a Teflon® slider and a RC wall. The damper is also designed to control normal pressures acting on a frictional slider. The numerical applications show that the proposed damper can be effective in mitigating the seismic responses of RC frame structures and reducing the damage to RC structural members. Copyright © 2004 John Wiley & Sons, Ltd.     

Study on the effect of the infill walls on the seismic performance of a reinforced concrete frame

Motivated by the seismic damage observed to reinforced concrete (RC) frame structures during the Wenchuan earthquake, the effect of infill walls on the seismic performance of a RC frame is studied in this paper. Infill walls, especially those made of masonry, offer some amount of stiffness and strength. Therefore, the effect of infill walls should be considered during the design of RC frames. In this study, an analysis of the recorded ground motion in the Wenchuan earthquake is performed. Then, a numerical model is developed to simulate the infill walls. Finally, nonlinear dynamic analysis is carried out on a RC frame with and without infill walls, respectively, by using CANNY software. Through a comparative analysis, the following conclusions can be drawn. The failure mode of the frame with infill walls is in accordance with the seismic damage failure pattern, which is strong beam and weak column mode. This indicates that the infill walls change the failure pattern of the frame, and it is necessary to consider them in the seismic design of the RC frame. The numerical model presented in this paper can effectively simulate the effect of infill walls on the RC frame.     

非一致地震波动输入下大型钢筋混凝土框架结构-地基体系地震响应规律

为探索非一致地震波动输入对大型钢筋混凝土框架结构地震响应的影响,基于OpenSees软件平台建立二维钢筋混凝土框架结构\|地基动力相互作用有限元模型。将El-Centro地震波按P波波形分别以0°、15°、30°和35°角入射该有限元模型进行计算,对比分析框架柱内力和楼层层间位移的地震响应。研究发现非一致地震波输入方法对于大型钢筋混凝土框架结构建筑动力响应影响明显,随着地震波入射角的增大,钢筋混凝土框架结构底层柱的轴力幅值减小,剪力幅值增大,而弯矩幅值变化较小,楼层层间位移幅值也随之增大。研究结果对于大型钢筋混凝土框架结构抗震设计具有参考意义。