砂-黏土双层地基极限承载力的数值研究

在实际工程中,常见天然的或通过人工换填形成的上部砂土、下部黏土的层状地基,目前关于这种双层地基极限承载力和破坏机制研究还不够深入。通过有限差分法建立双层地基数值模型,分析基底粗糙程度、砂土剪胀角和超载对地基破坏模式及极限承载力的影响,并根据有限差分法计算结果对强度加权平均法、应力扩散法和冲剪破坏法等现有实用计算方法的估算正确性进行评价。研究结果表明,基底粗糙程度对极限承载力的影响随着砂土内摩擦角的增大而减小;当剪胀角较小时,剪胀角变化对承载力的影响更为明显;当下层黏土强度较小时,超载的作用更明显。强度加权平均法由于低估破坏面影响深度导致砂土层权重较大,计算结果偏大;应力扩散法忽略了砂土剪切强度,在砂土层较厚时出现低估;冲剪破坏法由于可较为精确地计算砂土破坏面上抗剪强度和被动土压力,是3种实用方法中计算最准确的,当砂土厚度和黏土强度较大时,建议按太沙基经验公式对下卧黏土进行局部剪切破坏修正后确定极限承载力。     

Bearing capacity of square footings on reinforced layered soil

In the present study, an approximate method has been suggested to calculate the ultimate bearing capacity of a square footing resting on reinforced layered soil. The soil is reinforced with horizontal layers of reinforcement in the top layer of soil only. The pre requisite to the method is the ultimate bearing capacity of unreinforced layered soil, which can be determined from the methods already available in literature. The results have been validated with the model tests conducted on two layered soil compacted at different densities and the top layer reinforced with horizontal layers of geogrid reinforcement.     

条形基础加筋砂土地基极限承载力计算

基于传统的极限平衡条分法,利用临界滑动场法计算了条形基础的加筋地基极限承载力。假定土体处于极限平衡状态时,土体与筋材间存在均匀的摩擦力,通过建立土体条块极限平衡方程,推导了地基承载力的递推关系式。首先,设定计算土体范围,并划分条块和离散状态点;其次,根据递推公式计算各个状态点的参数,并搜索临界滑面;最后,根据搜索出的滑面计算地基承载力。通过实例比较进一步验证了计算结果的可靠性,并分析了首层筋带埋深、铺设层数和长度对地基承载力和滑面位置的影响。研究结果表明：地基承载力随着筋带埋深的增加先增大后减小;随着层数和长度的增加先逐渐增大,最后趋于稳定;滑面位置的变化规律主要是垂直影响深度和水平影响范围增大或减小。该方法原理简单、易于编程,为条形基础加筋地基承载力的计算提供了一种新思路,是临界滑动场法在地基承载力计算中的推广应用。     

考虑地表沉陷影响的复合地基承载力计算方法

受地下开采的剧烈扰动,采煤沉陷区的复合地基工程会发生非常大的下沉和水平位移,常规的承载力计算方法未考虑地表沉陷影响。在研究地表沉陷影响的复合地基承载特性的基础上,建立了考虑地表沉陷影响的复合地基受力模型,并且提出了考虑地表沉陷影响的复合地基承载力计算方法。通过一个采煤沉陷区桥梁复合地基工程实例的计算分析,发现考虑地表沉陷影响后,复合地基承载力有一定程度的下降。     

Bearing capacity of rectangular footings in uniform clay with deep embedment

This letter is concerned with the undrained bearing capacity of rectangular footings with various aspect ratios and embedment ratios in uniform clay. It covers thin plate foundations with low aspect ratios and high embedment depth with embedment ratio up to 150. The work is based on small strain finite element analysis (FEA). After verification of the FEA model against existing solutions of the bearing capacity factors of rectangular footings, a series of FEA results are obtained. Based on the FEA results, a simple formulation is proposed to calculate the bearing capacity factor for rectangle footing with different aspect ratio in any embedment depth, extending the existing solutions to cover a wider ranges of footing aspect ratios and embedment ratios.     

Bearing Capacity of Shallow Foundation on Two Clay Layers by Numerical Approach

Natural soils are often deposited in layers. The estimation of the bearing capacity of the soil, using conventional bearing capacity theory based on the properties of the top layer, introduces significant inaccuracies if the thickness of the top layer is comparable to the width of the rigid footing placed on the soil surface. Saturated normally consolidated and lightly overconsolidated clays indicate that under undrained condition the cohesion of soil mass increases almost linearly with depth. A few theoretical studies have been proposed in the literature to incorporate the variation of cohesion with depth in the computation of the ultimate bearing capacity of strip and circular footings. In this paper, after reviewing previous works, numerical computations using the FLAC code (Fast Lagrangian Analyses of Continua) are reported to evaluate the two layered clays effect on the bearing capacity beneath rigid strip footing subject to axial static load. The results of the bearing capacity relating to the relative thickness of the top layer, the strength ratio of the soil two-layered clays and the rates of the increase of soil cohesion with depth are presented in Tables and graphs. The obtained results are compared with previous published results available in the literature.     

浅论地基承载力的深度修正

为了确定修正后的复合地基承载力特征值,论述了天然地基承载力的深宽修正的理论依据,并指出《建筑地基基础设计规范》GB 50007-2002所给出计算方法的局限性。将复合地基分为散体桩、低粘结强度桩和高粘结强度桩复合地基三种情况予以讨论,通过理论推导,提出了复合地基承载力特征值深度修正的计算公式,并结合工程实际进行了验证。     

关于偏心荷载下地基承载力的验算方法

针对偏心荷载作用下的地基承载力验算,以条形基础为例,介绍了Meyerhof提出的考虑荷载偏心的地基承载力计算方法,并通过与有限元上下限极限分析这一极限荷载精细数值计算方法的比较验证了其正确性和准确性。所考虑的地基既包括排水条件下的一般地基,也包括不排水强度随深度近似线性增大的饱和黏性土地基。依据有关机理深入分析了基础埋深对偏心荷载下地基承载力计算精度的影响,明确了可以考虑基础埋深有利作用的偏心距上限。进而采用本课题组所提出计算地基承载力的改进公式,通过计算并结合理论分析比较了国内规范验算方法与按Meyerhof方法的验算,表明采用后一方法更为合理。     

公路路基地基承载力的离心模型试验与分析

公路路基由于基底的柔性和荷载分布为梯形,路基地基的破坏模式和确定方法与刚性基础地基有所差异,对公路路基地基承载力的研究具有重要的理论意义和实用价值。通过柔性条形基础、梯形路基以及模拟沟谷地形的柔性条形基础等3组离心模型试验,对公路路基地基的破坏机制和极限承载力进行了研究,并采用关联流动的Mohr-Coulomb内切圆屈服准则对试验结果进行了数值模拟和对比分析,研究结果表明,公路路基地基由于基底的柔性和较高的离心加速度,很难产生理想的整体剪切破坏形式;与刚柔性条形基础相比,梯形路基作用下的基底中心点沉降更大;沟谷地形对柔性条形基础基底中心点的沉降有一定的影响,但并不明显影响地基极限承载力。     

Effects of base geogrid on geocell-reinforced foundation beds

The effect of a base geogrid layer below the geocell mattress in sand, sand overlying soft clay, and soft clay foundation beds has been studied using a series of laboratory scale load tests. A rigid circular model footing was used to apply static monotonic loading on the foundation beds with and without geocell reinforcement. The model test results show that the provision of an additional layer of planar geogrid at the base of the geocell mattress further increases the performance of the footing in terms of bearing capacity and reduction in surface heave of the foundation bed. It is also observed that the beneficial effect of the base geogrid layer becomes negligible with increasing height of the geocell mattress beyond the influence of the depth of the footing. Strain measurements in the base geogrid layer indicate that it is more effective with the limited heights of the geocell mattress. The earth pressure cells embedded in the subgrade soil provide evidence that when the base geogrid is provided below the geocell mattress, the footing pressure is distributed more uniformly over an extended area.     

海洋静力触探在海上平台桩基承载力计算中的应用

静力触探探测具有原位性、连续性、高效性以及高分辨率的优点,利用海洋静力触探探测成果计算海上平台桩基承载力具有非常大的应用空间。以胜利油田埕岛海域某平台为例,使用ROSON100型海洋静力触探仪对平台各桩腿开展原位探测,同步进行钻探取样及室内土工参数测试。分别利用静力触探和钻探取样测试成果计算了平台桩基承载力,对比讨论了3种桩基承载力计算方法之间的异同。结果表明:3种方法对应的桩侧摩阻力随埋深变化整体趋势基本一致;基于一定区域工程经验,钻探规范法和静探间接法得到的桩端阻力、单桩极限承载力基本吻合,而静探直接法得到的桩端阻力和单桩极限承载力相较前两者明显偏大;考虑以粉砂作为持力层的前提下3种桩基极限承载力计算方法表现出较好的兼容性。研究成果可为海洋工程桩基承载力计算提供新的借鉴,具有一定科学意义和应用价值。     

基于非对称双侧破坏模式的临坡地基承载力上限分析

临坡地基已成为一种广泛的地基形式。针对临坡条形基础地基破坏模式的非对称性特点,首先引进双侧破坏模式的研究思路,重点考虑临坡地基基础两侧滑块大小和同一滑块几何形状的双重非对称性特征,构建了临坡条形基础地基非对称双侧破坏模式,为临坡地基承载力分析奠定了坚实基础;然后在此基础上,引进极限上限分析和优化理论,建立了临坡条形基础地基承载力分析的模型与方法,该方法不仅可考虑地基破坏模式,还可考虑基础与坡顶距离对临坡地基承载力的影响,而且还可较好地蜕化为平地地基承载力的分析;最后通过工程实例计算,并与现有相关分析方法进行对比分析,表明该方法的可行性与合理性以及普遍适用性。     

墙下条形基础与层状横观各向同性地基共同作用

运用对偶积分方程来求解层状横观各向同性地基与墙下条形基础的共同作用问题。从直角坐标平面应变问题控制方程出发,通过傅里叶（Fourier）变换和层间连续性条件,可以得到层状横观各向同性地基的传递矩阵解。基于该传递矩阵解,并利用条形基础与地基接触的混合边值条件,推导出一组关于基础挠度和地基反力的对偶积分方程。考虑墙下条形基础受到竖向集中荷载的情况,利用弹性薄板理论先求解出条形基础挠度;随后应用雅可比（Jacobi）正交多项式和级数展开的方法,将对偶积分方程转化为线性代数方程组进行求解。编制了相应的计算程序,其计算结果与有限元软件ABAQUS的结果基本吻合,从而验证了所提理论的正确性。算例分析表明,板土相对刚度与地基成层性对地基反力、地表沉降和沿z轴竖向正应力有很大的影响。     

港口工程中非均质层状地基承载力计算方法

在深水码头、防浪堤等大型港口工程建设中常常会遇到构筑物下覆地基由非均质的层状土构成的情况。对于这类非均质层状地基,我国港口工程地基规范推荐采用Hansen 61公式、Hansen 69公式和Sokolovskii数值解法3种方法计算地基的极限承载能力。然而,工程实践中由这3种方法计算得出的地基极限承载力数值往往有较大的差别。考虑到规范的继承性,基于牛顿迭代法,针对3个理论计算公式编制了计算程序,根据长江口深水治理二期工程地质实测资料,运用该计算程序对该地区地基的极限承载能力进行了计算比较。计算结果表明,对于非均质层状地基,在相同地质条件、相同荷载条件下Sokolovskii数值解法得到的承载力数值最大,Hansen 69公式得到的承载力数值最小。     

圆形基础地基极限承载力计算

利用临界滑动场法计算了浅埋圆形基础的地基承载力,并提供了系数N、Nq和Nc的计算表格和曲线,同时分析了侧面土压力对N、Nq的影响。通过建立土体条块极限平衡方程,推导了计算地基承载力的递推关系式。首先,设定土体计算范围,并划分条块和设置状态点; 其次,根据递推公式和推力极值原理计算各个状态点的参数,并搜索临界滑面; 最后,根据搜索出的临界滑面计算地基承载力。通过与已有系数计算值或模型试验的比较,验证了该方法的合理性。研究结果表明:N、Nq和Nc与其他学者的计算值相近; 相同情况下侧面土压力越大系数N、Nq越小。该方法是临界滑动场法在地基承载力研究中的推广应用,原理简单、易于编程,可为深入研究圆形基础地基承载力的计算提供参考。     

延吉—珲春地区圆砾层地基承载力研究

延吉—珲春地区的圆砾层是该区域工程建设经常利用的土层.为了获取圆砾层可靠的地基承载力数据,探讨确定地基承载力适宜的测试手段和方法,以及检验以前地基承载力数据的可靠度,采用载荷试验和重型圆锥动力触探试验原位测试方法对圆砾层的地基承载力进行了测试研究,获取了十二组地基承载力特征值、变形模量和重型圆锥动力触探锤击数试验数据.通过对试验数据的统计分析,得到了圆砾层地基承载力特征值的范围,得出地基承载力特征值、变形模量与重型圆锥动力触探锤击数线性相关的结论.据此,提出了适合当地工程地质条件的根据重型圆锥动力触探锤击数计算圆砾层地基承载力特征值和变形模量的经验公式.为延吉—珲春地区岩土工程勘察工作能够准确可靠、便捷、经济地确定圆砾层地基承载力特征值和变形模量提供了依据和方法,并为吉林省其他地区圆砾层地基承载力的研究提供了参考.     

非均质地基承载力及破坏模式的FLAC数值分析

利用基于Lagrangian显式差分的FLAC算法，通过数值计算，对黏结力随深度线性增长的非均质地基上条形基础和圆形基础的极限承载力及地基破坏模式进行了对比计算与系统分析。研究表明：（1）随着地基黏结力沿深度非均匀变化系数的增大，地基的破坏范围逐渐集中在地基表层和基础两侧：（2）即使地基的非均质程度较小，当将非均质地基近似地按均质地基考虑时，由此所估算的承载力可能过于保守；（3）地基承载力系数随黏结力沿深度非均匀变化系数的增大而非线性地增大。与数值解相比，skempton与Peck等近似公式均可能高估了非均质地基承载力。     

Experimental Study of Bearing Capacity of Granular Soils,Reinforced with Innovative Grid-Anchor System

The pull-out resistance of reinforcing elements is one of the most significant factors in increasing the bearing capacity of geosynthetic reinforced soils. In this research a new reinforcing element that includes elements (anchors) attached to ordinary geogrid for increasing the pull-out resistance of reinforcements is introduced. Reinforcement therefore consists of geogrid and anchors with cubic elements that attached to the geogrid, named (by the authors) Grid-Anchor. A total of 45 load tests were performed to investigate the bearing capacity of square footing on sand reinforced with this system. The effect of depth of the first reinforcement layer, the vertical spacing, the number and width of reinforcement layers, the distance that anchors are effective, effect of relative density, low strain stiffness and stiffness after local shear were investigated. Laboratory tests showed that when a single layer of reinforcement is used there is an optimum reinforcement embedment depth for which the bearing capacity is the greatest. There also appeared to be an optimum vertical spacing of reinforcing layers for multi-layer reinforced sand. The bearing capacity was also found to increase with increasing number of reinforcement layer, if the reinforcement were placed within a range of effective depth. The effect of soil density also is investigated. Finally the results were compared with the bearing capacity of footings on non-reinforced sand and sand reinforced with ordinary geogrid and the advantages of the Grid-Anchor were highlighted. Test results indicated that the use of Grid-Anchor to reinforce the sand increased the ultimate bearing capacity of shallow square footing by a factor of 3.0 and 1.8 times compared to that for un-reinforced soil and soil reinforced with ordinary geogrid, respectively.     

黄河三角洲地区地基承载力的确定

由于试验原理的不同,不同试验方法在判别土体破坏时的依据也不相同,而且有些试验需要经过概率统计的修正,导致由不同试验方法确定的承载力值之间存在较大的差异。不同试验所测得的数据与承载力之间具有一定的内在联系,利用这一特点,针对不同岩性的土体,采用回归分析法可以建立比贯入阻力与地基承载力值、标贯击数与地基承载力值、室内土工参数与地基承载力值的相关关系,以克服各试验方法间的差异性,为黄河三角洲地区高速公路勘察设计提供快速、准确的地基承载力特征值。     

成层软土地基预固结处理后桩基水平承载力估算方法

目前通过对软土地基预加固处理来提高桩基水平承载力已被工程界认可,但如何在工程前期设计过程中估算软土地基预处理后桩基水平承载力提高值仍是技术难点。基于此,参考Bowles[1]的地基土水平抗力计算式,同时考虑成层软土地基预排水固结处理影响,通过数学推导,推求出根据原状软土室内土工试验抗剪强度指标及预加固处理时间,估算软土地基预处理后桩基水平承载力提高值的实用计算方法。考虑桩侧土弹塑性屈服影响,推导出成层软土中水平受荷桩弹塑性解析解及塑性区深度的计算式,给出了桩顶水平位移、桩身最大弯矩的无量纲计算式及相关计算源代码。依托于浙江省某水闸桩基工程案例,根据提出的计算方法对桩基水平承载力、桩顶水平位移及桩身最大弯矩等性状进行预估计算,并与地基预处理前、后现场试桩检测值进行验证对比,认为桩基水平承载力、桩顶水平位移及桩身最大弯矩等预估计算成果与工程现场试桩的检测值较接近,对类似工程设计具有较好的参考价值。