Release of arsenic associated with the reduction and transformation of iron oxides

The behaviour of trace amounts of arsenate coprecipitated with ferrihydrite, lepidocrocite and goethite was studied during reductive dissolution and phase transformation of the iron oxides using [⁵⁵Fe]- and [⁷³As]-labelled iron oxides. The As/Fe molar ratio ranged from 0 to 0.005 for ferrihydrite and lepidocrocite and from 0 to 0.001 for goethite. For ferrihydrite and lepidocrocite, all the arsenate remained associated with the surface, whereas for goethite only 30% of the arsenate was desorbable. The rate of reductive dissolution in 10 mM ascorbic acid was unaffected by the presence of arsenate for any of the iron oxides and the arsenate was not reduced to arsenite by ascorbic acid. During reductive dissolution of the iron oxides, arsenate was released incongruently with Fe²⁺ for all the iron oxides. For ferrihydrite and goethite, the arsenate remained adsorbed to the surface and was not released until the surface area became too small to adsorb all the arsenate. In contrast, arsenate preferentially desorbs from the surface of lepidocrocite. During Fe²⁺ catalysed transformation of ferrihydrite and lepidocrocite, arsenate became bound more strongly to the product phases. X-ray diffractograms showed that ferrihydrite was transformed into lepidocrocite, goethite and magnetite whereas lepidocrocite either remained untransformed or was transformed into magnetite. The rate of recrystallization of ferrihydrite was not affected by the presence of arsenate. The results presented here imply that during reductive dissolution of iron oxides in natural sediments there will be no simple correlation between the release of arsenate and Fe²⁺. Recrystallization of the more reactive iron oxides into more crystalline phases, induced by the appearance of Fe²⁺ in anoxic aquifers, may be an important trapping mechanism for arsenic.     

Electronic structures of iron(III) and manganese(IV) (hydr)oxide minerals: Thermodynamics of photochemical reductive dissolution in aquatic environments

Sunlight-induced reduction and dissolution of colloidal Fe-Mn (hydr)oxide minerals yields elevated concentrations of Fe²⁺ and Mn²⁺ in natural waters. Since these elements may be biolimiting micronutrients, photochemical reactions might play a significant role in biogeochemical cycles. Reductive photodissolution of Fe (hydr)oxide minerals may also release sorbed metals. The reactivity of Fe-Mn (hydr)oxide minerals to sunlight-induced photochemical dissolution is determined by the electronic structure of the mineral-water interface. In this work, oxygen K-edge absorption and emission spectra were used to determine the electronic structures of iron(III) (hydr)oxides (hematite, goethite, lepidocrocite, akaganeite and schwertmannite) and manganese(IV) oxides (pyrolusite, birnessite, cryptomelane). The band gaps in the iron(III) (hydr)oxide minerals are near 2.0-2.5 eV; the band gaps in the manganese (IV) oxide phases are 1.0-1.8 eV. Using published values for the electrochemical flat-band potential for hematite together with experimental pH_pzc values for the (hydr)oxides, it is possible to predict the electrochemical potentials of the conduction and valence bands in aqueous solutions as a function of pH. The band potentials enable semiquantitative predictions of the susceptibilities of these minerals to photochemical dissolution in aqueous solutions. At pH 2 (e.g., acid-mine waters), photoreduction of iron(III) (hydr)oxides could yield millimolal concentrations of aqueous Fe²⁺ (assuming surface detachment of Fe²⁺ is not rate limiting). In seawater (pH 8.3), however, the direct photo-reduction of colloidal iron(III) (hydr)oxides to give nanomolal concentrations of dissolved, uncomplexed, Fe²⁺ is not thermodynamically feasible. This supports the hypothesis that the apparent photodissolution of iron(III) (hydr)oxides in marines systems results from Fe³⁺ reduction by photochemically produced superoxide. In contrast, the direct photoreduction of manganese oxides should be energetically feasible at pH 2 and 8.3.     

A Mössbauer spectroscopic study of the iron redox transition in eastern Mediterranean sediments

Fe cycling at two sites in the Mediterranean Sea (southwest of Rhodes and in the North Aegean) has been studied, combining the pore water determination of nutrients, manganese, and iron, citrate-bicarbonate-dithionite (CDB) and total sediment extractions, X-ray diffraction, and ⁵⁷Fe Mössbauer spectroscopy (MBS). At the Rhodes site, double peaks in the CDB-extractable Mn and Fe profiles indicate non-steady-state diagenesis. The crystalline iron oxide hematite, identified at both sites by room temperature (RT) MBS, appears to contribute little to the overall Fe reduction. MBS at liquid helium temperature (LHT) revealed that the reactive sedimentary Fe oxide phase was nanophase goethite, not ferrihydrite as is usually assumed. The pore water data at both sites indicates that upon reductive dissolution of nanophase goethite, the upward diffusing dissolved Fe²⁺ is oxidized by Mn oxides, rather than by nitrate or oxygen. The observed oxidation of Fe²⁺ by Mn oxides may be more common than previously thought but not obvious in sediments where the nitrate penetration depth coincides with the Mn oxide peak. At the Rhodes site, the solid-phase Fe(II) increase occurred at a shallower depth than the accumulation of dissolved Fe²⁺ in the pore water. The deeper relict Mn oxide peak acts as an oxidation barrier for the upward diffusing dissolved Fe²⁺, thereby keeping the pore water Fe²⁺ at depth. At the North Aegean site, the solid-phase Fe(II) increase occurs at approximately the same depth as the increase in dissolved Fe²⁺ in the pore water. Overall, the use of RT and cryogenic MBS provided insight into the solid-phase Fe(II) gradient and allowed identification of the sedimentary Fe oxides: hematite, maghemite, and nanophase goethite.     

Structural constraints of ferric (hydr)oxides on dissimilatory iron reduction and the fate of Fe(II)

Due to the strong reducing capacity of ferrous Fe, the fate of Fe(II) following dissimilatory iron reduction will have a profound bearing on biogeochemical cycles. We have previously observed the rapid and near complete conversion of 2-line ferrihydrite to goethite (minor phase) and magnetite (major phase) under advective flow in an organic carbon-rich artificial groundwater medium. Yet, in many mineralogically mature environments, well-ordered iron (hydr)oxide phases dominate and may therefore control the extent and rate of Fe(III) reduction. Accordingly, here we compare the reducing capacity and Fe(II) sequestration mechanisms of goethite and hematite to 2-line ferrihydrite under advective flow within a medium mimicking that of natural groundwater supplemented with organic carbon. Introduction of dissolved organic carbon upon flow initiation results in the onset of dissimilatory iron reduction of all three Fe phases (2-line ferrihydrite, goethite, and hematite). While the initial surface area normalized rates are similar (∼10⁻¹¹ mol Fe(II) m⁻² g⁻¹), the total amount of Fe(III) reduced over time along with the mechanisms and extent of Fe(II) sequestration differ among the three iron (hydr)oxide substrates. Following 16 d of reaction, the amount of Fe(III) reduced within the ferrihydrite, goethite, and hematite columns is 25, 5, and 1%, respectively. While 83% of the Fe(II) produced in the ferrihydrite system is retained within the solid-phase, merely 17% is retained within both the goethite and hematite columns. Magnetite precipitation is responsible for the majority of Fe(II) sequestration within ferrihydrite, yet magnetite was not detected in either the goethite or hematite systems. Instead, Fe(II) may be sequestered as localized spinel-like (magnetite) domains within surface hydrated layers (ca. 1 nm thick) on goethite and hematite or by electron delocalization within the bulk phase. The decreased solubility of goethite and hematite relative to ferrihydrite, resulting in lower Fe(III)_aq and bacterially-generated Fe(II)_aq concentrations, may hinder magnetite precipitation beyond mere surface reorganization into nanometer-sized, spinel-like domains. Nevertheless, following an initial, more rapid reduction period, the three Fe (hydr)oxides support similar aqueous ferrous iron concentrations, bacterial populations, and microbial Fe(III) reduction rates. A decline in microbial reduction rates and further Fe(II) retention in the solid-phase correlates with the initial degree of phase disorder (high energy sites). As such, sustained microbial reduction of 2-line ferrihydrite, goethite, and hematite appears to be controlled, in large part, by changes in surface reactivity (energy), which is influenced by microbial reduction and secondary Fe(II) sequestration processes regardless of structural order (crystallinity) and surface area.     

Comparative data on the volatile component composition of magma

Ferrihydrite (2.5 Fe₂O₂-4.5 H₂O) is an unstable colloidal mineral. It dissolves in highly alkaline solutions and is precipitated from them in the form of goethite. Jarosite is stable at very low pH but is decomposed at higher values of pH with separation of iron oxides. Experiments show that in rapid decomposition of jarosite a protohematite substance, ferrihydrite, is formed. This transformation occurs at moderate pH values when solutions percolate through the aggregates of jarosite. Ferrihydrite, an unstable colloidal hydrated oxide of ferric iron, changes spontaneously to stable hematite with time. Very slow decomposition of jarosite results in its replacement by iron hydroxide, goethite. Under laboratory conditions in alkaline solutions lepidocrocite may be obtained from jarosite. The synthesis of this iron hydroxide passes through a stage of intermediate products: ferrihydrite and hydrated ferric oxide - ferriprotolepidocrocite, formed by solution of ferrihydrite in strongly alkaline solutions. The transformation of ferriprotolepidocrocite into lepidocrocite may be regarded as a topotactic reaction. —Authors.     

Evidence for a simple pathway to maghemite in Earth and Mars soils

Soil magnetism is greatly influenced by maghemite (γ-Fe₂O₃), the presence of which is usually attributed to the following: (1) heating of goethite in the presence of organic matter; (2) oxidation of magnetite (Fe₃O₄); or (3) dehydroxylation of lepidocrocite (γ-FeOOH). Formation of the latter two minerals in turn requires the presence of Fe(II) in the system. No laboratory experiment or soil study to date has shown whether maghemite can form from ferrihydrite, a poorly crystalline Fe(III) oxide [∼Fe_4.5(O,OH,H₂O)_13.5], below 250°C. However, ferrihydrite is the usual precursor of goethite (α-FeOOH) and hematite (α-Fe₂O₃), the most frequently occurring crystalline Fe(III) oxides in soils. Here is presented in vitro evidence that ferryhidrite can partly transform into maghemite at 150°C. This transformation occurs upon aging of ferrihydrite precipitated in the presence of phosphate or other ligands capable of ligand exchange with Fe-OH surface groups. This maghemite coexists with hematite and is a transient phase in the transformation of ferrihydrite to hematite, which is apparently stabilized by the adsorbed ligands. Its particle size is small (10 to 30 nm), and its X-ray diffraction pattern exhibits superstructure reflections. The possible formation of maghemite in Mars and in different Earth soils can partly be explained in the light of this pathway with minimal ad hoc assumptions.     

铁（氢）氧化物悬液中磷酸盐的吸附-解吸特性研究

铁（氢）氧化物对P的吸持和释放在一定程度上决定着P的生物有效性和水体富营养化。以两种环境中常见晶质铁氧化物（针铁矿和赤铁矿）为对照,采用X射线衍射（XRD）、透射电镜（TEM）、热重分析（TGA）和孔径分析以及动力学和吸附-解吸热力学平衡等技术方法,研究了弱晶质水铁矿对P吸附-解吸特性,并探讨了相关机制。实验表明,三种矿物对P的吸附分为起始的快速反应和随后的慢速反应,它们均符合准一级动力学过程,反应中OH释放明显滞后于P吸附,P吸附经历了从外围到内囤配位、单齿到多齿配位过渡的过程,与晶质氧化铁比,水铁矿吸附容量和OH释放量更大、慢速吸附反应更快、存在缓慢扩散反应阶段,吸附容量依次是：水铁矿（436μmol／m^2）〉针铁矿（262μmol／m^2）〉赤铁矿（228μmol／m^2）,针铁矿和赤铁矿吸附P符合L（Langmuir）模型,而水铁矿更符合F（Fremldlictl）模型。中性盐介质（KCl）中在最大吸附量时P的解吸率依次为：水铁矿（85％）〈针铁矿（10％）〈赤铁矿（125％）,柠檬酸通过配体解吸和诱导溶解两种机制促进P的解吸,最大吸附量时解吸率依次是：针铁矿（25％）〈水铁矿（32％）〈赤铁矿（50％）。     

Mössbauer hyperfine parameters of iron species in the course of <Emphasis Type="Italic">Geobacter</Emphasis>-mediated magnetite mineralization

Amorphous ferric iron species (ferrihydrite or akaganeite of <5 nm in size) is the only known solid ferric iron oxide that can be reductively transformed by dissimilatory iron-reducing bacteria to magnetite completely. The lepidocrocite crystallite can be transformed into magnetite in the presence of abiotic Fe(II) at elevated pH or biogenic Fe(II) with particular growth conditions. The reduction of lepidocrocite by dissimilatory iron-reducing bacteria has been widely investigated showing varying results. Vali et al. (Proc Natl Acad Sci USA 101:16121–16126, 2004) captured a unique biologically mediated mineralization pathway where the amorphous hydrous ferric oxide transformed to lepidocrocite was followed by the complete reduction of lepidocrocite to single-domain magnetite. Here, we report the ⁵⁷Fe Mössbauer hyperfine parameters of the time-course samples reported in Vali et al. (Proc Natl Acad Sci USA 101:16121–16126, 2004). Both the quadrupole splittings and linewidths of Fe(III) ions decrease consistently with the change of aqueous Fe(II) and transformations of mineral phases, showing the Fe(II)-mediated gradual regulation of the distorted coordination polyhedrons of Fe³⁺ during the biomineralization process. The aqueous Fe(II) catalyzes the transformations of Fe(III) minerals but does not enter the mineral structures until the mineralization of magnetite. The simulated abiotic reaction between Fe(II) and lepidocrocite in pH-buffered, anaerobic media shows the simultaneous formation of green rust and its gradual transformation to magnetite plus a small fraction of goethite. We suggested that the dynamics of Fe(II) supply is a critical factor for the mineral transformation in the dissimilatory iron-reducing cultures.     

The effect of silica and natural organic matter on the Fe(II)-catalysed transformation and reactivity of Fe(III) minerals

The Fe(II)-catalysed transformation of synthetic schwertmannite, ferrihydrite, jarosite and lepidocrocite to more stable, crystalline Fe(III) oxyhydroxides is prevented by high, natural concentrations of Si and natural organic matter (NOM). Adsorption isotherms demonstrate that Si adsorbs to the iron minerals investigated and that increasing amounts of adsorbed Si results in a decrease in isotope exchange between aqueous Fe(II) and the Fe(III) mineral. This suggests that the adsorption of Si inhibits the direct adsorption of Fe(II) onto the mineral surface, providing an explanation for the inhibitory effect of Si on the Fe(II)-catalysed transformation of Fe(III) minerals. During the synthesis of lepidocrocite and ferrihydrite, the presence of equimolar concentrations of Si and Fe resulted in the formation of 2-line ferrihydrite containing co-precipitated Si in both cases. Isotope exchange experiments conducted with this freeze-dried Si co-precipitated ferrihydrite species (Si-ferrihydrite) demonstrated that the rate and extent of isotope exchange between aqueous Fe(II) and solid ⁵⁵Fe(III) was very similar to that of 2-line ferrihydrite formed in the absence of Si and which had not been allowed to dry. In contrast to un-dried ferrihydrite formed in the absence of Si, Si-ferrihydrite did not transform into a more crystalline Fe(III) mineral phase over the 7-day period of investigation. Reductive dissolution studies using ascorbic acid demonstrated that both dried Si-ferrihydrite and un-dried 2-line ferrihydrite were very reactive, suggesting these species may be major contributors to the rapid release of dissolved iron following flooding and the onset of conditions conducive to reductive dissolution in acid sulphate soil environments.     

Environmental monitoring of magnetic iron phases of urban water reservoir lake sediments (Taiaçupeba Lake,metropolitan region of São Paulo,Brazil) by using Mössbauer spectroscopy

In the present work, we investigate the iron oxides and oxyhydroxides behavior and evolution, related to the geochemical behavior of some metals, which could be retained as solid phases in the sediments from an urban water reservoir lake, placed in Taiaçupeba, Great São Paulo, Brazil. These tasks were performed by the establishment of a proceduring setting for environmental monitoring analysis through Mössbauer spectroscopy measurements associated to hysteresis loops measurements and chemical analysis [X-ray fluorescence (XRF)]. We inferred the possibility of goethite occurrence in broad particle size distribution (5–50 nm), and related to ferrihydrite, and small grain-size hematite (about 8 nm). The magnetometry results pointed to the paramagnetic/superparamagnetic behavior of the magnetic phases present in the samples and also suggested the occurrence of small grain-size magnetite. We also verified the presence of clay minerals related to Fe, as well as the occurrence of Fe³⁺ and/or Fe²⁺ in short-range structural order. Through a straight correlation among Mössbauer spectra data gained at T = 77 K and Al-metal, metal-Fe molar ratios, provided through XRF data, we found remarkable indications of interference on meta-stable phases evolution to its final products. Such results can be pointing for evidences about the possible isomorphic replacing and/or adsorption of Al and other metals in goethite and hematite.     

磷灰石对湖泊沉积物中水铁矿稳定性的制约

通过在滇池开展原位实验,研究探讨了湖泊沉积物中磷灰石制约水铁矿分解和转化的机制,以及二者共存时的环境效应。结果表明:将水铁矿放置到沉积物中1个月,矿物保持稳定;放置时间达到3个月时,添加磷灰石实验中水铁矿发生了显著物相转变。冬天(12—2月)实验中,转化产物随深度的变化趋势为针铁矿+磁(赤)铁矿→针铁矿+纤铁矿→针铁矿;夏天(6—9月)实验中,转化产物随深度的变化趋势为针铁矿+纤铁矿+磁(赤)铁矿→针铁矿+纤铁矿→未转化。透射电镜分析结果显示冬天实验中生成的磁性铁氧化物为纳米磁铁矿和磁赤铁矿,夏天实验中产生的则主要为纳米磁铁矿。X射线光电子能谱分析结果显示冬天表层实验样品具有较高P含量。分析表明的湖泊沉积物中磷灰石促进水铁矿转化的过程为:(1)微生物促进磷灰石溶解;(2)磷灰石溶解释放的P促进铁还原菌生长;(3)铁还原菌促进水铁矿还原;(4)水铁矿还原产生的溶解态Fe²⁺催化水铁矿向针铁矿、纤铁矿和磁铁矿转化。冬天及沉积氧化-还原界面最适宜磷灰石分解菌和铁还原菌生长,水铁矿的转化和P释放能力也更强,相应地内源磷释放的风险也更大。     

Microbial sulfidogenesis in ferrihydrite-rich environments: Effects on iron mineralogy and arsenic mobility

Microbial sulfidogenesis plays a potentially important role in Fe and As biogeochemistry within wetland soils, sediments and aquifers. This study investigates the specific effects of microbial sulfidogenesis on Fe mineralogy and associated As mobility in mildly acidic (pH 6) and mildly basic (pH 8) advective-flow environments. A series of experiments were conducted using advective-flow columns, with an initial solid-phase comprising As(III)-bearing ferrihydrite-coated quartz sand. Columns for each pH treatment were inoculated with the sulfate-reducing bacteria Desulfovibrio vulgaris, and were compared to additional abiotic control columns. Over a period of 28 days, microbial sulfidogenesis (as coupled to the incomplete oxidation of lactate) caused major changes in Fe mineralogy, including replacement of ferrihydrite by mackinawite and magnetite at the in-flow end of the inoculated columns. At pH 8, the Fe²⁺ produced by electron transfer between sulfide and ferrihydrite was mainly retained near its zone of formation. In contrast, at pH 6, much of the produced Fe²⁺ was transported with advecting groundwater, facilitating the downstream Fe²⁺-catalyzed transformation of ferrihydrite to goethite. At both pH 6 and pH 8, the sulfide-driven reductive dissolution of ferrihydrite and its replacement by mackinawite at the in-flow end of the inoculated columns resulted in substantial mobilization of As into the pore-water. At pH 8, this caused the downstream As concentrations within the inoculated columns to be greater than the corresponding abiotic column. However, the opposite occurred under pH 6 conditions, with the Fe²⁺-catalyzed transformation of ferrihydrite to goethite in the inoculated columns causing a decrease in downstream As concentrations compared to the abiotic column. Although thermodynamically favorable at intermediate times and depth intervals within the inoculated columns, solid As sulfide phases were undetectable by As XANES spectroscopy. Our findings show that microbial sulfidogenesis can trigger significant As mobilization in subsurface environments with advective groundwater flow. The results also demonstrate that formation of mackinawite by sulfidization of ferric (hydr)oxides is not effective for the immobilization of As, whereas the Fe²⁺-catalyzed transformation of ferrihydrite to goethite under mildly acidic conditions may mitigate As mobility.     

Contrasting effects of Al substitution on microbial reduction of Fe(III) (hydr)oxides

Aluminum, one of the most abundant elements in soils and sediments, is commonly found co-precipitated with Fe in natural Fe(III) (hydr)oxides; yet, little is known about how Al substitution impacts bacterial Fe(III) reduction. Accordingly, we investigated the reduction of Al substituted (0-13 mol% Al) goethite, lepidocrocite, and ferrihydrite by the model dissimilatory Fe(III)-reducing bacterium (DIRB), Shewanella putrefaciens CN32. Here we reveal that the impact of Al on microbial reduction varies with Fe(III) (hydr)oxide type. No significant difference in Fe(III) reduction was observed for either goethite or lepidocrocite as a function of Al substitution. In contrast, Fe(III) reduction rates significantly decreased with increasing Al substitution of ferrihydrite, with reduction rates of 13% Al-ferrihydrite more than 50% lower than pure ferrihydrite. Although Al substitution changed the minerals’ surface area, particle size, structural disorder, and abiotic dissolution rates, we did not observe a direct correlation between any of these physiochemical properties and the trends in bacterial Fe(III) reduction. Based on projected Al-dependent Fe(III) reduction rates, reduction rates of ferrihydrite fall below those of lepidocrocite and goethite at substitution levels equal to or greater than 18 mol% Al. Given the prevalence of Al substitution in natural Fe(III) (hydr)oxides, our results bring into question the conventional assumptions about Fe (hydr)oxide bioavailability and suggest a more prominent role of natural lepidocrocite and goethite phases in impacting DIRB activity in soils and sediments.     

Effects of sediment iron mineral composition on microbially mediated changes in divalent metal speciation: Importance of ferrihydrite

Dissimilatory metal reducing bacteria (DMRB) can influence geochemical processes that affect the speciation and mobility of metallic contaminants within natural environments. Most investigations into the effect of DMRB on sediment geochemistry utilize various synthetic oxides as the Fe^III source (e.g., ferrihydrite, goethite, hematite). These synthetic materials do not represent the mineralogical composition of natural systems, and do not account for the effect of sediment mineral composition on microbially mediated processes. Our experiments with a DMRB (Shewanella putrefaciens 200) and a divalent metal (Zn^II) indicate that, while complexity in sediment mineral composition may not strongly impact the degree of “microbial iron reducibility,” it does alter the geochemical consequences of such microbial activity. The ferrihydrite and clay mineral content are key factors. Microbial reduction of a synthetic blend of goethite and ferrihydrite (VHSA-G) carrying previously adsorbed Zn^II increased both [Zn^II-aq] and the proportion of adsorbed Zn^II that is insoluble in 0.5 M HCl. Microbial reduction of Fe^III in similarly treated iron-bearing clayey sediment (Fe-K-Q) and hematite sand, which contained minimal amounts of ferrihydrite, had no similar effect. Addition of ferrihydrite increased the effect of microbial Fe^III reduction on Zn^II association with a 0.5 M HCl insoluble phase in all sediment treatments, but the effect was inconsequential in the Fe-K-Q. Zinc k-edge X-ray absorption spectroscopy (XAS) data indicate that microbial Fe^III reduction altered Zn^II bonding in fundamentally different ways for VHSA-G and Fe-K-Q. In VHSA-G, ZnO₆ octahedra were present in both sterile and reduced samples; with a slightly increased average Zn-O coordination number and a slightly higher degree of long-range order in the reduced sample. This result may be consistent with enhanced Zn^II substitution within goethite in the microbially reduced sample, though these data do not show the large increase in the degree of Zn-O-metal interactions expected to accompany this change. In Fe-K-Q, microbial Fe^III reduction transforms Zn-O polyhedra from octahedral to tetrahedral coordination and leads to the formation of a ZnCl₂ moiety and an increased degree of multiple scattering. This study indicates that, while many sedimentary iron minerals are easily reduced by DMRB, the effects of microbial Fe^III reduction on trace metal geochemistry are dependent on sediment mineral composition.     

Aluminum coprecipitates with Fe (hydr)oxides: Does isomorphous substitution of Al for Fe in goethite occur?

Iron (hydr)oxides are common in natural environments and typically contain large amounts of impurities, presumably the result of coprecipitation processes. Coprecipitation of Al with Fe (hydr)oxides occurs, for example, during alternating reduction-oxidation cycles that promote dissolution of Fe from Fe-containing phases and its re-precipitation as Fe-Al (hydr)oxides. We used chemical and spectroscopic analyses to study the formation and transformation of Al coprecipitates with Fe (hydr)oxides. In addition, periodic density functional theory (DFT) computations were performed to assess the structural and energetic effects of isolated or clustered Al atoms at 8 and 25 mol% Al substitution in the goethite structure. Coprecipitates were synthesized by raising the pH of dilute homogeneous solutions containing a range of Fe and Al concentrations (100% Fe to 100% Al) to 5. The formation of ferrihydrite in initial suspensions with ?20 mol% Al, and of ferrihydrite and gibbsite in initial suspensions with ?25 mol% Al was confirmed by infrared spectroscopic and synchrotron-based X-ray diffraction analyses. While base titrations showed a buffer region that corresponded to the hydrolysis of Fe in initial solutions with ?25 mol% Al, all of the Al present in these solutions was retained by the solid phases at pH 5, thus indicating Al coprecipitation with the primary Fe hydroxide precipitate. In contrast, two buffer regions were observed in solutions with ?30 mol% Al (at pH ∼2.25 for Fe³⁺ and at pH ∼4 for Al³⁺), suggesting the formation of Fe and Al (hydr)oxides as two separate phases. The Al content of initial coprecipitates influenced the extent of ferrihydrite transformation and of its transformation products as indicated by the presence of goethite, hematite and/or ferrihydrite in aged suspensions. DFT experiments showed that: (i) optimized unit cell parameters for Al-substituted goethites (8 and 25 mol% Al) in clustered arrangement (i.e., the formation of diaspore-like clusters) were in good agreement with available experimental data whereas optimized unit cell parameters for isolated Al atoms were not, and (ii) Al-substituted goethites with Al in diaspore-like clusters resulted in more energetically favored structures. Combined experimental and DFT results are consistent with the coprecipitation of Al with Fe (hydr)oxides and with the formation of diaspore-like clusters, whereas DFT results suggest isomorphous Al for Fe substitution within goethite is unlikely at ?8 mol% Al substitution.     

Adsorption and surface oxidation of Fe(II) on metal (hydr)oxides

The Fe(II) adsorption by non-ferric and ferric (hydr)oxides has been analyzed with surface complexation modeling. The CD model has been used to derive the interfacial distribution of charge. The fitted CD coefficients have been linked to the mechanism of adsorption. The Fe(II) adsorption is discussed for TiO₂, γ-AlOOH (boehmite), γ-FeOOH (lepidocrocite), α-FeOOH (goethite) and HFO (ferrihydrite) in relation to the surface structure and surface sites. One type of surface complex is formed at TiO₂ and γ-AlOOH, i.e. a surface-coordinated Fe²⁺ ion. At the TiO₂ (Degussa) surface, the Fe²⁺ ion is probably bound as a quattro-dentate surface complex. The CD value of Fe²⁺ adsorbed to γ-AlOOH points to the formation of a tridentate complex, which might be a double edge surface complex. The adsorption of Fe(II) to ferric (hydr)oxides differs. The charge distribution points to the transfer of electron charge from the adsorbed Fe(II) to the solid and the subsequent hydrolysis of the ligands that coordinate to the adsorbed ion, formerly present as Fe(II). Analysis shows that the hydrolysis corresponds to the hydrolysis of adsorbed Al(III) for γ-FeOOH and α-FeOOH. In both cases, an adsorbed M(III) is found in agreement with structural considerations. For lepidocrocite, the experimental data point to a process with a complete surface oxidation while for goethite and also HFO, data can be explained assuming a combination of Fe(II) adsorption with and without electron transfer. Surface oxidation (electron transfer), leading to adsorbed Fe(III)(OH)₂, is favored at high pH (pH > ∼7.5) promoting the deprotonation of two Fe_III-OH₂ ligands. For goethite, the interaction of Fe(II) with As(III) and vice versa has been modeled too. To explain Fe(II)-As(III) dual-sorbate systems, formation of a ternary type of surface complex is included, which is supposed to be a monodentate As(III) surface complex that interacts with an Fe(II) ion, resulting in a binuclear bidentate As(III) surface complex.     

Iron(III) accumulations in inland saline waterways,Hunter Valley,Australia: Mineralogy,micromorphology and pore-water geochemistry

Discharge of Fe(II)-rich groundwaters into surface-waters results in the accumulation of Fe(III)-minerals in salinized sand-bed waterways of the Hunter Valley, Australia. The objective of this study was to characterise the mineralogy, micromorphology and pore-water geochemistry of these Fe(III) accumulations. Pore-waters had a circumneutral pH (6.2–7.2), were sub-oxic to oxic (Eh 59–453 mV), and had dissolved Fe(II) concentrations up to 81.6 mg L⁻¹. X-ray diffraction (XRD) on natural and acid-ammonium-oxalate (AAO) extracted samples indicated a dominance of 2-line ferrihydrite in most samples, with lesser amounts of goethite, lepidocrocite, quartz, and alumino-silicate clays. The majority of Fe in the samples was bound in the AAO extractable fraction (Fe^Ox) relative to the Na-dithionite extractable fraction (Fe^Di), with generally high Fe^Ox:Fe^Di ratios (0.52–0.92). The presence of nano-crystalline 2-line ferrihydrite (Fe₅HO₃·4H₂O) with lesser amounts of goethite (α-FeOOH) was confirmed by scanning electron microscopy (SEM) coupled with energy dispersive X-ray analysis (EDX), and transmission electron microscopy (TEM) coupled with selected area electron diffraction (SAED). In addition, it was found that lepidocrocite (γ-FeOOH), which occurred as nanoparticles as little as ∼5 lattice spacings thick perpendicular to the (0 2 0) lattice plane, was also present in the studied Fe(III) deposits. Overall, the results highlight the complex variability in the crystallinity and particle-size of Fe(III)-minerals which form via oxidation of Fe(II)-rich groundwaters in sand-bed streams. This variability may be attributed to: (1) divergent precipitation conditions influencing the Fe(II) oxidation rate and the associated supply and hydrolysis of the Fe(III) ion, (2) the effect of interfering compounds, and (3) the influence of bacteria, especially Leptothrix ochracea.     

Stable Fe isotope fractionations produced by aqueous Fe(II)-hematite surface interactions

Stable Fe isotope fractionations were investigated during exposure of hematite to aqueous Fe(II) under conditions of variable Fe(II)/hematite ratios, the presence/absence of dissolved Si, and neutral versus alkaline pH. When Fe(II) undergoes electron transfer to hematite, Fe(II) is initially oxidized to Fe(III), and structural Fe(III) on the hematite surface is reduced to Fe(II). During this redox reaction, the newly formed reactive Fe(III) layer becomes enriched in heavy Fe isotopes and light Fe isotopes partition into aqueous and sorbed Fe(II). Our results indicate that in most cases the reactive Fe(III) that undergoes isotopic exchange accounts for less than one octahedral layer on the hematite surface. With higher Fe(II)/hematite molar ratios, and the presence of dissolved Si at alkaline pH, stable Fe isotope fractionations move away from those expected for equilibrium between aqueous Fe(II) and hematite, towards those expected for aqueous Fe(II) and goethite. These results point to formation of new phases on the hematite surface as a result of distortion of Fe-O bonds and Si polymerization at high pH. Our findings demonstrate how stable Fe isotope fractionations can be used to investigate changes in surface Fe phases during exposure of Fe(III) oxides to aqueous Fe(II) under different environmental conditions. These results confirm the coupled electron and atom exchange mechanism proposed to explain Fe isotope fractionation during dissimilatory iron reduction (DIR). Although abiologic Fe(II)_aq - oxide interaction will produce low δ⁵⁶Fe values for Fe(II)_aq, similar to that produced by Fe(II) oxidation, only small quantities of low-δ⁵⁶Fe Fe(II)_aq are formed by these processes. In contrast, DIR, which continually exposes new surface Fe(III) atoms during reduction, as well as production of Fe(II), remains the most efficient mechanism for generating large quantities of low-δ⁵⁶Fe aqueous Fe(II) in many natural systems.     

The oxidation of carbonate green rust into ferric phases:solid-state reaction or transformation via solution

The oxidation of carbonate green rust, GR(CO₃²⁻), in NaHCO₃ solutions at T = 25°C has been investigated through electrochemical techniques, FTIR, XRD, TEM and SEM. The used GR(CO₃²⁻) samples were made of either suspended solid in solution or a thin electrochemically formed layer on the surface of an iron disc. Depending on experimental conditions, oxidation occurs, with or without major modifications of the GR(CO₃²⁻) structure, suggesting the existence of two pathways: solid-state oxidation (SSO) leading to a ferric oxyhydroxycarbonate as the end product, and a dissolution-oxidation-precipitation (DOP) mechanism leading to ferric oxihydroxides such as lepidocrocite, goethite, or ferrihydrite. A formula was proposed for this ferric oxyhydroxycarbonate, Fe₆^IIIO_(2+x)(OH)_(12-2x)(H₂O)_x(CO₃), assuming that the solid-state oxidation reaction is associated to a deprotonation of the water molecules within the interlayers, or of the hydroxyl groups in the Fe(O,H) octahedra layers. The DOP mechanism involves transformation via solution with the occurrence of soluble ferrous-ferric intermediate species. A discussion about factors influencing the oxidation of carbonate green rust is provided hereafter. The ferric oxyhydroxycarbonate can be reduced back to GR(CO₃²⁻) by a reverse solid-state reduction reaction. The potentiality for a solid-state redox cycling of iron to occur may be considered. The stability of the ferric oxyhydroxycarbonate towards thermodynamically stable ferric phases, such as goethite and hematite, was also studied.     

Fe isotopic fractionation during mineral dissolution with and without bacteria

Fe released into solution is isotopically lighter (enriched in the lighter isotope) than hornblende starting material when dissolution occurs in the presence of the siderophore desferrioxamine mesylate (DFAM). In contrast, Fe released from goethite dissolving in the presence of DFAM is isotopically unchanged. Furthermore, Δ⁵⁶Fe_{solution-hornblende} for Fe released to solution in the presence of ligands varies with the affinity of the ligand for Fe. The extent of isotopic fractionation of Fe released from hornblende also increases when experiments are agitated continuously. The Fe isotope fractionation observed during hornblende dissolution with organic ligands is attributed predominantly to retention of ⁵⁶Fe in an altered surface layer, while the lack of isotopic fractionation during goethite dissolution in DFAM is consistent with the lack of an altered layer. When a siderophore-producing soil bacterium is added to the system (without added organic ligands), Fe released to solution from both hornblende and goethite differs isotopically from Fe in the bulk mineral: Δ⁵⁶Fe_{solution-starting material} = −0.56 ± 0.19 (hornblende) and −1.44 ± 0.16 (goethite). Increased isotopic fractionation is attributed in this case to the fact that as bacterial respiration depletes the system in oxygen and aqueous Fe is reduced, equilibration between aqueous ferrous and ferric iron creates a pool of isotopically heavy ferric iron that is assimilated by bacterial cells. Adsorption of isotopically heavy ferrous iron (Fe(II) enriched in the heavier isotope) or precipitation of isotopically heavy Fe minerals may also contribute to observed fractionations.To test whether these Fe isotope signatures are recorded in natural systems, we also investigated extractions of samples of soils from which the bacteria were isolated. These extractions show variability in the isotopic signatures of exchangeable Fe and Fe oxyhydroxide fractions from one soil sample to another, but exchangeable Fe is observed to be lighter than Fe in soil Fe oxyhydroxides and hornblende. This observation is consistent with isotopically light Fe-organic complexes in soil pore water derived from the Fe-silicate starting materials in the presence of growing microorganisms, as documented in experiments reported here. The contributions from phenomena including organic ligand-promoted nonstoichiometric dissolution of Fe silicates, uptake of ferric iron by organisms, adsorption of isotopically heavy ferrous iron, and precipitation of iron minerals should create complex isotopic signatures in soils. Better understanding of these processes and the timescales over which they contribute to fractionation is needed.