Removal of Chromium from Synthetic Effluent using Nymphaea rubra

In the present work, biosorption of Cr(VI) by Nymphaea rubra was investigated in batch studies. Batch experiments were conducted to study the effect of initial sorbent dosage, solution pH and initial Cr(VI) concentration. The results showed that the equilibrium uptake capacity was increased with decrease in biomass dosage. The Cr(VI) removal was influenced by the initial chromium compound concentration. Langmuir and Freundlich adsorption isotherm models were used to represent the equilibrium data. The Freundlich isotherm model was fitted very well with the equilibrium data when compared to Langmuir isotherm model. The sorption results were analyzed for pseudo‐first order and pseudo‐second order kinetic model. It was observed that the kinetic data fitted very well with the pseudo‐second order rate equation when compared to the pseudo‐first order rate equation. Fourier transform infrared spectrum showed the presence of different functional groups in the biomass. The surface morphology of the sorbent was exemplified by SEM analysis. Aquatic weeds seem to be a promising biosorbent for the removal of chromium ions from water environment. This paper reports the research findings of a laboratory‐based study on the removal of Cr(VI) from the synthetic solution using the dried stem of N. rubra as a biosorbent.     

Removal of Organic Pollutants from Wastewater Using Wood Fly Ash as a Low‐Cost Sorbent

In this study, untreated and treated wood fly ash (WA) was used as a low‐cost sorbent in batch sorption tests to investigate the removal of organic pollutants from a real wastewater generated by cleaning/washing of machinery in a wood‐laminate floor industry in Sweden. The experiments focused on the effect of the WA dosage and particle size on the removal efficiency for organic compounds. With a WA dosage of 160 g L^?1 and a particle size less than 1 mm, the reductions of chemical oxygen demand (COD), biologic oxygen demand, and total organic carbon were 37 ± 0.4, 24 ± 0.4, and 30 ± 0.3%, respectively. Pre‐treatment of WA with hot water improved the COD removal efficiency by absorption from 37 ± 0.4 to 42 ± 1.6% when the same dosage (160 g L^?1) was applied. Sorption isotherm and sorption kinetics for COD using untreated WA can be explained by Freundlich isotherm and pseudo‐second‐order kinetic models. Intra‐particle diffusion model indicates that pore diffusion is not the rate‐limiting step for COD removal. Based on the experimental data, WA could be used as an alternative low‐cost sorption media/filter for removal of organic compounds from real industrial wastewater.     

Removal of COD from Industrial Effluent Containing Indigo Dye Using Adsorption Method by Activated Carbon Cloth: Optimization,Kinetic, and Isotherm Studies

The pollution of underground and surface water streams is a tremendous environmental problem. Adsorption, in which activated carbon (AC) is used as an adsorbent, is one of efficient procedures to remove organic and inorganic pollutants from industrial wastewaters. Activated carbon fiber (ACF), a newly developed form of AC, has high adsorption rate and surface area and can be used for the treatment of industrial wastewaters. In this work, ACF was prepared by physicochemical activation method from kenaf and we studied its ability in the treatment of indigo‐containing wastewater produced from a dying factory. The filtered wastewater was treated via adsorption by ACF, and response surface experimental design method was used to study the effect of ACF dosage, contact time, temperature, and pH of the wastewater on the removal process. ACF dosage of 0.256 g, temperature of 12.5°C, pH 8.5, and contact time of 125 min were optimum treatment conditions. The adsorption process obeys pseudo‐second‐order kinetic and Freundlich isotherm models.     

Experimental and Isothermal Studies on Sorption of Congo Red by Modified Mycelial Biomass of Wood‐rotting Fungus

Batch biosorption experiments were carried out for the removal of Congo red from aqueous solution using native and pretreated mycelial pellets/biomass of Trametes versicolor. The effect of process parameters such as contact time, dye concentration, and pH on the extent of Congo red biosorption has been investigated. Higher dye concentrations resulted in lower biosorption. Increases in biomass dosage led to increases in the levels of biosorption. Biosorption kinetics and equilibrium data are essential basic requirements to develop an effective and accurate design model for the removal of the dye. A kinetic study showed that the biosorption of the dye on fungal biomass was a gradual process. Pseudo‐first‐order, pseudo‐second‐order, and Bangham's model were used to fit the experimental data. The results of the kinetic studies showed that the second‐order kinetic model fitted well for the present experimental data. Equilibrium isotherms were analyzed by Langmuir, Freundlich, Dubnin‐Radushkevich, and Temkin isotherms. The biosorption equilibrium data obeyed the Langmuir and Temkin isotherms well. Acidic pH was favorable for the biosorption of the dye. Studies on the pH effect and desorption show that chemisorption seems to play a major role in the biosorption process. Among the native and pretreated biomass studied, autoclaved biomass showed a better biosorption capacity.     

Use of Pistachio Shells as an Adsorbent for the Removal of Zinc(II) Ion

In this study, the removal of zinc(II) ion from an aqueous solution by pistachio shells (PS) is investigated. The dynamic behavior of the adsorption is examined on the effects of pH, adsorbent dosage, and contact time. The adsorption rates are determined quantitatively and simulated by the Lagergren first order, pseudo‐second order, Elovich, and intra‐particle diffusion kinetic models. The adsorption kinetic models are also tested for validity. The thermodynamic parameters, which are also deduced from adsorption experiments, are very useful in elucidating the nature of adsorption. The experimental results reveal that the optimum pH value and the contact time for the adsorption of Zn²⁺ onto PS are found as 6 and 10 min, respectively. According to these parameters, adsorption process follows the pseudo‐second order kinetic model with high correlation coefficients (R² = 0.999). The obtained results demonstrate that PS is a reasonably effective adsorbent for the removal of Zn²⁺ from aqueous leachate of hazardous waste.     

Biosorption of Methylene Blue from Aqueous Solution Using a Bioenergy Forest Waste: Xanthoceras sorbifolia Seed Coat

Xanthoceras sorbifolia seed coat (XSSC), a bioenergy forest waste, was used for the adsorption of methylene blue (MB) from aqueous solutions. The effects of adsorbent dosage, pH, adsorbate concentration and contact time on MB biosorption were studied. The equilibrium adsorption data was analyzed by Langmuir and Freundlich isotherm models. The results indicated that the Langmuir model provided the best correlation with the experimental data. The adsorption capacity of XSSC for MB was determined with the Langmuir model and was found to be 178.6 mg/g at 298 K. The adsorption kinetic data was modeled using the pseudo‐first order, pseudo‐second order, and intraparticle diffusion kinetic equations. It was seen that the pseudo‐second order equation could describe the adsorption kinetics, and intraparticle diffusion was not the sole rate controlling factor. Thermodynamic parameters were also evaluated. Standard Gibbs free energy was spontaneous for all interactions, and the biosorption process exhibited exothermic standard enthalpy values. The results indicated that XSSC is an attractive alternative for removing cationic dyes from wastewater.     

Adsorption Characteristics of Reactive Black 5 from Aqueous Solution onto Chitosan

Adsorption of reactive black 5 (RB5) from aqueous solution onto chitosan was investigated in a batch system. The effects of solution pH, initial dye concentration, and temperature were studied. Adsorption data obtained from different batch experiments were modeled using both pseudo first‐ and second‐order kinetic equations. The equilibrium adsorption data were fitted to the Freundlich, Tempkin, and Langmuir isotherms over a dye concentration range of 45–100 µmol/L. The best results were achieved with the pseudo second‐order kinetic and Langmuir isotherm equilibrium models, respectively. The equilibrium adsorption capacity (q_e) was increased with increasing the initial dye concentration and solution temperature, and decreasing solution pH. The chitosan flakes for the adsorption of the dye was regenerated efficiently through the alkaline solution and was then reused for dye removal. The activation energy (E_a) of sorption kinetics was estimated to be 13.88 kJ/mol. Thermodynamic parameters such as changes in free energy (ΔG), enthalpy (ΔH), and entropy (ΔS) were evaluated by applying the van't Hoff equation. The thermodynamics of reactive dye adsorption by chitosan indicates its spontaneous and endothermic nature.     

Adsorption Kinetic Modeling of Safranin onto Rice Husk Biomatrix Using Pseudo‐first‐ and Pseudo‐second‐order Kinetic Models: Comparison of Linear and Non‐linear Methods

Batch kinetic studies were carried out for the removal of safranin from aqueous solution using a biomatrix prepared from rice husk. The adsorption kinetic data were modeled using the pseudo‐first‐order and pseudo‐second‐order kinetic equations. The linear and non‐linear forms of these two widely used kinetic models were compared in this study. In order to determine the best‐fitting equation, the coefficient of determination (r²), the sum of the squares of the errors (SSE), sum of the absolute errors (SAE), average relative error (ARE), hybrid fractional error function (HYBRID), Marquardt's percent standard deviation (MPSD), and the Chi‐squared test (χ²) were used as error analysis methods. Results showed that the non‐linear forms of pseudo‐first‐order and pseudo‐second‐order models were more suitable than the linear forms for fitting the experimental data. Non‐linear method is thus more appropriate for estimating the kinetic parameters and should primarily be used to describe adsorption kinetics.     

Malachite Green Removal from Aqueous Solution by the Peel of Cucumis sativa Fruit

This study investigates the potential use of activated carbon prepared from the peel of Cucumis sativa fruit for the removal of malachite green (MG) dye from simulated wastewater. The effects of different system variables, adsorbent dosage, initial dye concentration, pH, and contact time were investigated and optimal experimental conditions were ascertained. The results showed that when the amount of the adsorbent increased, the percentage of dye removal increased accordingly. Optimum pH value for dye adsorption was 6.0. Maximum dye was sequestered within 50 min of the start of every experiment. The adsorption of MG followed the pseudo‐second‐order rate equation and fits the Langmuir, Freundlich, Dubinin–Radushkevich (D–R), and Tempkin equations well. The maximum removal of MG was obtained at pH 6 as 99.86% for adsorbent dose of 1 g/50 mL and 25 mg L^?1 initial dye concentration at room temperature. Activated carbon developed from the peel of C. sativa fruit can be an attractive option for dye removal from diluted industrial effluents since test reaction made on simulated dyeing wastewater showed better removal percentage of MG.     

Biosorption Kinetics and Isotherm Studies of Cd(II) by Dried Enteromorpha compressa Macroalgae Cells from Aqueous Solutions

For the first time ever, Enteromorpha compressa macroalgae (ECM), which is commonly found in Turkey, has been used as biosorbent by us. This study aims to investigate the biosorption of Cd²⁺ from aqueous solutions in a batch system by using an alga of ECM in different concentrations, pH levels, agitation rates (90–150 rpm), and contact periods. The maximum biosorption capacity of the ECM was found to be 9.50 mg/g at pH 6, Cd²⁺ initial concentration of 10 mg/L and agitation rate 150 rpm. Cadmium removal efficiency was about 95%. The experimental isotherm data were analyzed using the Langmuir and Freundlich equations. Isotherm parameters for both equations were determined and discussed. The stated biosorption mechanism is explained by the Freundlich isotherm (r² = 0.998) theory. Two simplified kinetic models including a pseudo‐first‐ and second‐order equation were selected to follow the biosorption process. Kinetic parameters; rate constants, equilibrium adsorption capacities and related correlation coefficients, for each kinetic model were calculated and discussed. It was shown that the biosorption of cadmium onto ECM could be described by the pseudo‐second‐order equation (r² > 0.99).     

Adsorption of Selenium Using Bagasse Fly Ash

The present work involves the study of Se(IV) adsorption onto bagasse fly ash. The adsorbents were coated with a ferric chloride solution for the effective removal of selenium. The physico‐chemical characterization of the adsorbent was carried out using standard methods, e. g., proximate analysis, scanning electron microscopy, Fourier transform infrared spectroscopy, thermo‐gravimetric analysis and differential thermal analysis. Batch experiments were carried out to determine the effect of various parameters such as adsorbent dose, initial pH, contact time, and temperature on the adsorption process. Results obtained from these studies were analyzed using various kinetic models and isotherms. Se(IV) adsorption onto adsorbent was high at low pH values, and decreased with an increase in initial pH. A temperature study showed that the uptake of Se(IV) was greatest at 293 K, within the temperature range studied. The parameters of pseudo first order, pseudo second order, and Weber‐Morris intra‐particle kinetic models were determined. Equilibrium isotherms were analyzed using Langmuir, Freundlich, and Temkin isotherms. Error analyses were also carried out using hybrid fractional error function and Marquardt's percent standard deviation.     

Adsorption of Cadmium Ions from Aqueous Solution Using Granular Activated Carbon and Activated Clay

The present study was aimed at removing cadmium ions from aqueous solution through batch studies using adsorbents, such as, granular activated carbon (GAC) and activated clay (A‐clay). GAC was of commercial grade where as the A‐clay was prepared by acid treatment of clay with 1 mol/L of H₂SO₄. Bulk densities of A‐clay and GAC were 1132 and 599 kg/m³, respectively. The surface areas were 358 m²/g for GAC and 90 m²/g for A‐clay. The adsorption studies were carried out to optimize the process parameters, such as, pH, adsorbent dosage, and contact time. The results obtained were analyzed for kinetics and adsorption isotherm studies. The pH value was optimized at pH 6 giving maximum Cd removal of 84 and 75.2% with GAC and A‐clay, respectively. The adsorbent dosage was optimized and was found to be 5 g/L for GAC and 10 g/L for A‐clay. Batch adsorption studies were carried out with initial adsorbate (Cd) concentration of 100 mg/L and adsorbent dosage of 10 g/L at pH 6. The optimum contact time was found to be 5 h for both the adsorbents. Kinetic studies showed Cd removal a pseudo second order process. The isotherm studies revealed Langmuir isotherm to better fit the data than Freundlich isotherm.     

Effect of Temporal Changes in Air Injection Rate on Air Sparging Performance Groundwater Remediation

Air sparging (AS) is a commonly applied method for treating groundwater contaminated with volatile organic compounds (VOCs). When using a constant injection of air (continuous mode), a decline in remediation efficiency is often observed, resulting from insufficient mixing of contaminants at the pore scale. It is well known that turning the injection on and off (pulsed mode) may lead to a better remediation performance. In this article, we investigate groundwater mixing and contaminant removal efficiency in different injection modes (i.e., continuous and pulsed), and compare them to those achieved in a third mode, which we denote as “rate changing.” In this mode, injection is always on, and its rate is varying with time by abrupt changes. For the purpose of this investigation, we conducted two separate sets of experiments in a laboratory tank. In the first set of experiments, we used dye plume tracing to characterize the mixing induced by AS. In the second set of experiments, we contaminated the tank with a VOC and compared the remediation efficiency between the different injection modes. As expected, we observed that time‐variable injection modes led to enhanced mixing and contaminant removal. The decrease in contaminant concentrations during the experiment was found to be double for the “rate changing” and “pulsed” modes compared to the continuous mode, with a slightly preferable performance for the “rate changing” mode. These results highlight the critical role that mixing plays in AS, and support the need for further investigation of the proposed “rate changing” injection mode.     

Remediation of Iron,Manganese, and Organic Pollutants in Lignite‐Derived Water Using an Upflow Biological Aerated Filter

A large amount of lignite‐derived water is created during the process of refining lignite. The concentration of Fe, Mn, phenol, and some other organic pollutants of the lignite‐derived water is above the discharge permit or circulating cooling water reuse standard in China. A laboratory‐scale upflow biological aerated filter (UBAF) was developed to treat this lignite‐derived water. Three kinds of coke powders, as waste products in the coal chemical industry with 0.1–0.4 mm, 0.5–1.0 mm, and 1.0–2.0 mm in diameter, were tested as the UBAF's carrier materials. A comparative study of gas–water ratio for the UBAF is presented. The studies presented in this paper demonstrate that with coke powder diameter of 0.5–1.0 mm and gas/water ratio of 7:1, the UBAF reactor can achieve optimal removal efficiency. After the UBAF treatment, the removal efficiency of Fe, Mn, and phenol was found to be 38.4–62.5%, 56.6–74.3%, and 89.5–94.3%, respectively. The lignite‐derived water can meet the discharge permit to surface water and reuse standard for circulating cooling water after the treatment by UBAF. The coke powder, as a waste material, can be used as a support material for UBAF very well.     

Removal of Carbamazepine,Naproxen, and Trimethoprim from Water by Amberlite XAD‐7: A Kinetic Study

The adsorption kinetics of carbamazepine, naproxen, and trimethoprim in aqueous solution by Amberlite? XAD‐7 has been studied. The influence of adsorbent dose (1–3 g/L), stirring rate (80–240 rpm), pH (2–9), temperature (20–60°C), and initial concentration (25–75 ppm) on the adsorption kinetics has been analyzed. The removal efficiency in the first 2 h reaches 85% for carbamazepine, 60% for naproxen, and 70% for trimethoprim. pH appears to be the most important factor conditioning the removal of these latter solutes, whereas carbamazepine adsorption seems to be independent of the pH of the adsorptive solution. Initial concentration and operation temperature moderately influence the adsorption process. Finally, stirring rate scarcely affects the process. The experimental data have been fitted to four kinetic models, namely pseudo‐first and pseudo‐second order, intra‐particle diffusion and Bangham's. The model providing the best fit is the pseudo‐second order one. Again, pH is the factor that affects the adsorption rate in a more remarkable manner although other parameters such as temperature and stirring rate also contribute to accelerate the removal of the solutes. Under the optimal operation conditions, Amberlite? XAD‐7 exhibits a promising ability for the removal of the pharmaceuticals under study.     

Removal of Copper,Nickel, and Zinc Ions from Electroplating Rinse Water

Removal of copper, nickel, and zinc ions from synthetic electroplating rinse water was investigated using cationic exchange resin (Ceralite IR 120). Batch ion exchange studies were carried out to optimize the various experimental parameters (such as contact time, pH, and dosage). Influence of co‐existing cations, chelating agent EDTA on the removal of metal ion of interest was also studied. Sorption isotherm data obtained at different experimental conditions were fitted with Langmuir, Freundlich, Redlich–Peterson, and Toth models. A maximum adsorption capacity of 164 mg g^?1 for Cu(II), 109 mg g^?1 for Ni(II), and 105 mg g^?1 for Zn(II) was observed at optimum experimental conditions according to Langmuir model. The kinetic data for metal ions adsorption process follows pseudo second‐order. Presence of EDTA and co‐ions markedly alters the metal ion removal. Continuous column ion exchange experiments were also conducted. The breakeven point of the column was obtained after recovering effectively several liters of rinse water. The treated rinse water could be recycled in rinsing operations. The Thomas and Adams–Bohart models were applied to column studies and the constants were evaluated. Desorption of the adsorbed metal ions from the resin column was studied by conducting a model experiments with Cu(II) ions loaded ion exchange resin column using sulfuric acid as eluant. A novel lead oxide coated Ti substrate dimensionally stable (DSA) anode was prepared for recovery of copper ions as metal foil from regenerated liquor by electro winning at different current densities (50–300 A cm^?2).     

Adsorption of Basic Dyes from Aqueous Solutions by Depolymerization Products of Post‐Consumer PET Bottles

The purpose of this work is the removal of basic dyes (Safranine T and Brilliant Green) from aqueous media by depolymerization products (DP) obtained from aminoglycolysis of waste poly(ethylene terephthalate) (PET). The surface morphology and physical properties of depolymerization product were also determined. Adsorption behaviors (adsorption capacities, adsorption kinetics and adsorption isotherms) of these samples were realized at room temperature. Then, the amounts of residual dye concentrations were measured using Visible Spectrophotometer at 530 and 618 nm for Safranine T (ST) and Brilliant Green (BG), respectively. All adsorption experiments were carried out for different depolymerization products (DP1, DP2, DP3, and DP4). Adsorption capacities of depolymerization products for both of dyes decrease with following order: DP2 > DP4 > DP1 > DP3. The maximum adsorption capacities for ST and BG onto DP2 sample were found to be 29 and 33 mg g^?1, respectively. In addition, the adsorption kinetic results show that the pseudo‐second‐order kinetic model is more suitable than pseudo‐first‐order model for the adsorption of basic dyes onto DP samples. Adsorption data were evaluated using Langmuir and Freundlich adsorption isotherm models. The results revealed that the adsorption of basic dyes onto DP sample fit very well Langmuir isotherm model. In conclusion, the depolymerization products of post‐consumer PET bottles can be used as low cost adsorbent for the removal of basic dyes from wastewaters.     

Removal of the Azo Dye Congo Red from Aqueous Solutions by the Marine Alga Porphyra yezoensis Ueda

Batch adsorption experiments were carried out using nonliving biomass of Porphyra yezoensis Ueda (red alga) for the removal of Congo red from aqueous solutions at 25°C. The effects of process parameters such as contact time, adsorbent concentration and ionic strength were investigated. The raw biomass and Congo red loaded biomass were characterized by Fourier transform infrared spectroscopy (FTIR). The pseudo first order, pseudo second order and intraparticle diffusion models were tested. The results showed that adsorption of Congo red followed pseudo second order kinetics very well. Langmuir and Freundlich equations were applied to the data related to the adsorption isotherms, and the observed maximum adsorption capacities (q_m) were 71.46 mg/g at 25°C. Adsorbent concentration and ionic strength had a marked effect on Congo red adsorption.