Removal of COD from Industrial Effluent Containing Indigo Dye Using Adsorption Method by Activated Carbon Cloth: Optimization,Kinetic, and Isotherm Studies

The pollution of underground and surface water streams is a tremendous environmental problem. Adsorption, in which activated carbon (AC) is used as an adsorbent, is one of efficient procedures to remove organic and inorganic pollutants from industrial wastewaters. Activated carbon fiber (ACF), a newly developed form of AC, has high adsorption rate and surface area and can be used for the treatment of industrial wastewaters. In this work, ACF was prepared by physicochemical activation method from kenaf and we studied its ability in the treatment of indigo‐containing wastewater produced from a dying factory. The filtered wastewater was treated via adsorption by ACF, and response surface experimental design method was used to study the effect of ACF dosage, contact time, temperature, and pH of the wastewater on the removal process. ACF dosage of 0.256 g, temperature of 12.5°C, pH 8.5, and contact time of 125 min were optimum treatment conditions. The adsorption process obeys pseudo‐second‐order kinetic and Freundlich isotherm models.     

Dye Removal from Colored Textile Wastewater by Poly(propylene imine) Dendrimer: Operational Parameters and Isotherm Studies

This paper deals with the removal of textile dyes from aqueous solutions by poly(propylene imine) dendrimer (PPI). Direct red 80 (DR80), Acid Green 25 (AG25), Acid Blue 7 (AB7), and Direct Red 23 (DR23) were used as model dyes. The effects of operational parameters on dye removal such as dendrimer concentration, dye concentration, salt (inorganic anions), and pH have been studied at 25°C. The Langmuir and Freundlich isotherm models were investigated. In addition, dye desorption of dendrimer was studied. The results indicated that acidic pH supported the adsorption of dyes by dendrimer. Furthermore studies of dye concentration and salt effects exhibited that dye removal percentage by dendrimer was decreased. It was found that the isotherm data of DR80, AG25, and DR23 followed Langmuir isotherm and isotherm data of AB7 followed Freundlich isotherm models. Desorption tests showed that maximum dye releasing of 76.5% for DR80, 84.5% for AG25, 87% for AB7, and 93% for DR23 were achieved in aqueous solution at pH 12. Based on the data of present study, one could conclude that the dendrimer being an environmentally friendly adsorbent with relatively large adsorption capacity might be a suitable alternative for elimination of dyes from colored textile wastewater.     

Treatability of Dye Solutions Containing Disperse Dyes by Fenton and Fenton‐Solar Light Oxidation Processes

This study attempts to explore the possibility of treating dye solutions containing Disperse Yellow 119 and Disperse Red 167 by Fenton and Fenton under solar‐light oxidation processes. Experiments were conducted to examine the effects of various operating conditions on the performance of the treatment systems. The Fenton results showed that 98.6% spectral absorption coefficient (SAC) and 90.8% chemical oxygen demand (COD) removals were proved at pH 3, 50 mg/L Fe²⁺, and 75 mg/L H₂O₂, 15 min oxidation time for Disperse Yellow 119. After 40 min solar irradiation time during Fenton process the SAC removal was 99.1%. COD reduction of about 98.3% was observed at the same time. It was also obtained as 97.8% SAC and 97.7% COD removal with pH 3, 75 mg/L Fe²⁺, 100 mg/L H₂O₂, and 25 min oxidation time for Disperse Red 167 at this optimum conditions. For Disperse Red 167 during Fenton under solar light process, after 40 min of solar irradiation time the SAC and COD reduction were obtained 99.3 and 98.4%, respectively.     

Response Surface Optimization of Acid Red 119 Dye Adsorption by Mixtures of Dried Sewage Sludge and Sewage Sludge Ash

The mixtures of dried sewage sludge (DSS) and sewage sludge ash were studied for removal of acid red 119 (AR119) dye as a new, more environmental friendly, and low cost adsorbent. For this purpose, response surface methodology was applied to optimize the dye removal efficiency and turbidity of treated dye solutions as two individual responses. Results revealed that an optimum condition under specified constraints (dye removal efficiency >95% and turbidity <50 NTU) was obtained at a contact time of 60 min, 40 wt% DSS in the mixture, an initial pH of 6, and an initial dye concentration of 200 mg dye/L in distilled water. Under the optimal condition, dye removal efficiency of 94.98% and effluent turbidity of 24.9 NTU was observed. In further studies, at optimum condition, the effect of some additives on adsorption process and desorption/reusability of adsorbent was investigated. It was observed that removal efficiency was significantly decreased to 83.76% when a simulated dye wastewater (containing the selected dye, acetic acid, and Glauber's salt dissolved in tap water) was used. Desorption studies revealed that AR119 dye could be well removed from dye‐loaded adsorbent by 0.3 M NaOH solution.     

Central Composite Design Optimization of Biological Dye Removal in the Presence of Macroalgae Chara sp.

Response surface methodology (RSM) was employed to investigate the effects of different operational parameters on the biological decolorization of a dye solution containing malachite green (MG) in the presence of macroalgae Chara sp. The investigated variables were the initial pH, initial dye concentration, algae amount, and reaction time. Central composite design (CCD) was used for the optimization of biological decolorization process. Predicted values were found to be in good agreement with experimental values (R² = 0.982 and Adj‐R² = 0.966), which indicated suitability of the employed model and the success of RSM. The results of optimization predicted by the model showed that maximum decolorization efficiency was achieved at the optimum condition of the initial pH 6.8, initial dye concentration 9.7 mg/L, algae amount 3.9 g, and reaction time 75 min. UV–VIS spectra and FT‐IR analysis showed degradation of MG.     

Preparation of Nano‐Lepidocrocite and an Investigation of Its Ability to Remove a Metal Complex Dye

Lepidocrocite (γ‐FeOOH) nanoparticles were synthesized from iron(II) sulfate solution and characterized using X‐ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform‐IR (FT‐IR), nitrogen adsorption, and point of zero charge pH (pH_PZC) analyses. TEM, XRD, and FT‐IR analyses proved the synthesis of nano‐lepidocrocite. Surface area and pH_PZC of the synthesized lepidocrocite were 68.1 m² g^?1 and 4.8, respectively. Utilization of the synthesized lepidocrocite in the adsorption of Lanacron brown S‐GL (LBS‐GL) from aqueous solutions was investigated, and the effect of lepidocrocite dosage, pH, temperature, and contact time on this process were optimized and modeled using response surface methodology approach. The lepidocrocite dosage of 0.015 g, pH 3.5, temperature of 38°C, and contact time of 100 min were determined as optimum adsorption conditions. Isotherm and kinetics of the adsorption process were analyzed at the optimum conditions. The equilibrium data were fitted well to the Langmuir isotherm model. The maximum monolayer adsorption capacity was 528.21 mg g^?1. The adsorption process was described by the pseudo‐second‐order kinetic model. Furthermore, the effect of pH on the desorption of LBS‐GL was investigated. High LBS‐GL desorption efficiency was achieved at a high pH value.     

Optimization of a Photo‐assisted Fenton Oxidation Process: A Statistical Model for MDF Effluent Treatment

In the present study, the effects of initial COD (chemical oxygen demand), initial pH, Fe²⁺/H₂O₂ molar ratio and UV contact time on COD removal from medium density fiberboard (MDF) wastewater using photo‐assisted Fenton oxidation treatment were investigated. In order to optimize the removal efficiency, batch operations were carried out. The influence of the aforementioned parameters on COD removal efficiency was studied using response surface methodology (RSM). The optimal conditions for maximum COD removal efficiency from MDF wastewater under experimental conditions were obtained at initial COD of 4000 mg/L, Fe²⁺/H₂O₂ molar ratio of 0.11, initial solution pH of 6.5 and UV contact time of 70 min. The obtained results for maximum COD removal efficiency of 96% revealed that photo‐assisted Fenton oxidation is very effective for treating MDF wastewater.     

Adsorption of Basic Dyes from Aqueous Solutions by Depolymerization Products of Post‐Consumer PET Bottles

The purpose of this work is the removal of basic dyes (Safranine T and Brilliant Green) from aqueous media by depolymerization products (DP) obtained from aminoglycolysis of waste poly(ethylene terephthalate) (PET). The surface morphology and physical properties of depolymerization product were also determined. Adsorption behaviors (adsorption capacities, adsorption kinetics and adsorption isotherms) of these samples were realized at room temperature. Then, the amounts of residual dye concentrations were measured using Visible Spectrophotometer at 530 and 618 nm for Safranine T (ST) and Brilliant Green (BG), respectively. All adsorption experiments were carried out for different depolymerization products (DP1, DP2, DP3, and DP4). Adsorption capacities of depolymerization products for both of dyes decrease with following order: DP2 > DP4 > DP1 > DP3. The maximum adsorption capacities for ST and BG onto DP2 sample were found to be 29 and 33 mg g^?1, respectively. In addition, the adsorption kinetic results show that the pseudo‐second‐order kinetic model is more suitable than pseudo‐first‐order model for the adsorption of basic dyes onto DP samples. Adsorption data were evaluated using Langmuir and Freundlich adsorption isotherm models. The results revealed that the adsorption of basic dyes onto DP sample fit very well Langmuir isotherm model. In conclusion, the depolymerization products of post‐consumer PET bottles can be used as low cost adsorbent for the removal of basic dyes from wastewaters.     

Removal of EDTA from Aqueous Solutions Using Activated Carbon Prepared from Rubber Wood Sawdust: Kinetic and Equilibrium Modeling

Adsorptive removal of EDTA (ethylenediaminetetraacetic acid) from aqueous solution was studied using steam pyrolyzed activated carbon. Rubber wood sawdust, obtained from a local timber facility at Kodangavila, Trivandrum, Kerala, India was used as the precursor for the production of the activated carbon. Batch adsorption experiments were employed to monitor and optimize the removal process. The experimental parameters, i. e., solution pH, agitation time, initial EDTA concentration and adsorbent dosage, affecting the adsorption of EDTA onto sawdust activated carbon (SDAC) were optimized. The inner core mechanism for the interaction between EDTA and SDAC, which resulted in the adsorption process, was also discussed. The change in amount of EDTA adsorbed onto SDAC and CAC (commercial activated carbon) was compared over a wide range of pH (2.0–8.0). The maximum removal of EDTA took place in the pH range of 4.0–6.0 for SDAC and 5.0–5.5 for CAC, which demonstrates the effectiveness of the former adsorbent. Kinetic as well as equilibrium studies were performed to determine the rate constant and adsorption capacity, respectively. The adsorption kinetic data was fitted with pseudo‐first‐order kinetics and the equilibrium data was shown to follow the Langmuir isotherm model. These observations explain the formation of a monolayer of EDTA on the surface of SDAC as confirmed by the slow approach to equilibrium after 4 h of contact time. The adsorption capacity of SDAC for the removal of EDTA was 0.526 mmol/g and is seen to be greater than that of CAC and other reported adsorbents (0.193–0.439 mmol/g). Finally, it is clear that the production of steam pyrolyzed activated carbon in the presence of K₂CO₃ greatly enhanced EDTA removal and resulted in a product with possible commercial value for wastewater treatment strategies.     

Experimental Designs Applied to Desorption of Dichromate Ions after Separation and Preconcentration from Natural and Industrial Water by Modified Nano‐Alumina

Nano‐alumina modified by 9‐aminoacridine was used as a sorbent for separation and determination of dichromate ions from water. Statistical method, based on surface response design, has been used for the optimization of dichromate ions elution from 9‐aminoacridine nano‐alumina. The adsorbed dichromate ions were found to be eluted quantitatively with 0.8 mol L^?1 KCl in 1.6 mol L^?1 NaOH which optimized by response surface design. Under optimum conditions, the accuracy, precision (relative standard deviation, RSD%) and R‐square of the method were calculated as >98, <3, and >94%, respectively. Remarkable agreement between experimental and theoretical data was confirmed the predicted assumption. The method was applied to the simultaneous determination of dichromate in natural and industrial water samples. We also examined the retention of dichromate anions in the presence of Cl^?, , and anions at pH 3.     

Ionic Liquid Modified Resin for the Adsorptive Removal of Dibutyl Phthalate: Equilibrium,Kinetic, and Thermodynamic Studies

This study evaluated the adsorptive properties of dibutyl phthalate (DBP) on room temperature ionic liquid (RTIL) modified XAD‐4 resin. The modified RTIL‐XAD 4 sorbent was characterized by FTIR. Effect of varying experimental conditions such as pH, contact time, temperature, shaking speed, concentrations, and interfering species were investigated by batch adsorption experiments. Adsorption was found to be most favorable at pH 6 within 30 min. Experimental data were evaluated in terms of kinetic, equilibrium, and thermodynamic modeling. Kinetics of the sorption was found to follow pseudo second order rate equation whereas Freundlich and D–R isotherms were the most suitable models to explain sorption phenomenon. Thermodynamically sorption was endothermic, irreversible, and spontaneous in nature.